首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
On 11 March 2011, a moment magnitude M w = 9.0 earthquake occurred off the Japan Tohoku coast causing catastrophic damage and loss of human lives. In the immediate aftermath of the earthquake, we conducted the reconnaissance survey in the city of Rikuzentakata, Japan. In comparison with three previous historical tsunamis impacting the same region, the 2011 event presented the largest values with respect to the tsunami height, the inundation area and the inundation distance. A representative tsunami height of 15 m was recorded in Rikuzentakata, with increased heights of 20 m around rocky headlands. In terms of the inundation area, the 2011 Tohoku tsunami exceeded by almost 2.6 times the area flooded by the 1960 Chilean tsunami, which ranks second among the four events compared. The maximum tsunami inundation distance was 8.1 km along the Kesen River, exceeding the 1933 Showa and 1960 Chilean tsunami inundations by factors of 6.2 and 2.7, respectively. The overland tsunami inundation distance was less than 2 km. The tsunami inundation height linearly decreased along the Kesen River at a rate of approximately 1 m/km. Nevertheless, the measured inland tsunami heights exhibit significant variations on local and regional scales. A designated “tsunami control forest” planted with a cross-shore width of about 200 m along a 2 km stretch of Rikuzentakata coastline was completely overrun and failed to protect the local community during this extreme event. Similarly, many designated tsunami shelters were too low and were overwashed by tsunami waves, thereby failing to provide shelter for evacuees—a risk that had been underestimated.  相似文献   

2.
The 2010 Mentawai earthquake (magnitude 7.7) generated a destructive tsunami that caused more than 500 casualties in the Mentawai Islands, west of Sumatra, Indonesia. Seismological analyses indicate that this earthquake was an unusual “tsunami earthquake,” which produces much larger tsunamis than expected from the seismic magnitude. We carried out a field survey to measure tsunami heights and inundation distances, an inversion of tsunami waveforms to estimate the slip distribution on the fault, and inundation modeling to compare the measured and simulated tsunami heights. The measured tsunami heights at eight locations on the west coasts of North and South Pagai Island ranged from 2.5 to 9.3 m, but were mostly in the 4–7 m range. At three villages, the tsunami inundation extended more than 300 m. Interviews of local residents indicated that the earthquake ground shaking was less intense than during previous large earthquakes and did not cause any damage. Inversion of tsunami waveforms recorded at nine coastal tide gauges, a nearby GPS buoy, and a DART station indicated a large slip (maximum 6.1 m) on a shallower part of the fault near the trench axis, a distribution similar to other tsunami earthquakes. The total seismic moment estimated from tsunami waveform inversion was 1.0 × 1021 Nm, which corresponded to Mw 7.9. Computed coastal tsunami heights from this tsunami source model using linear equations are similar to the measured tsunami heights. The inundation heights computed by using detailed bathymetry and topography data and nonlinear equations including inundation were smaller than the measured ones. This may have been partly due to the limited resolution and accuracy of publically available bathymetry and topography data. One-dimensional run-up computations using our surveyed topography profiles showed that the computed heights were roughly similar to the measured ones.  相似文献   

3.
The M w = 9.0 earthquake that occurred off the coast of Japan’s Tohoku region produced a great tsunami causing catastrophic damage and loss of life. Within hours of the tsunami event, satellite data were readily available and massive media coverage immediately circulated thousands of photographs and videos of the tsunami. Satellite data allow a rapid assessment of inundated areas where access can be difficult either as a result of damaged infrastructure (e.g., roads, bridges, ports, airports) or because of safety issues (e.g., the hazard at Nuclear Power Plant at Fukushima). In this study, we assessed in a day tsunami inundation distances and runup heights using satellite data (very high-resolution satellite images from the GeoEye1 satellite and from the DigitalGlobe worldview, SRTM and ASTER GDEM) of the Tohoku region, Northeast Japan. Field survey data by Japanese and other international scientists validated our results. This study focused on three different locations. Site selection was based on coastal morphologies and the distance to the tsunami source (epicenter). Study sites are Rikuzentakata, Oyagawahama, and Yagawahama in the Oshika Peninsula, and the Sendai coastal plain (Sendai City to Yamamoto City). Maximum inundation distance (6 km along the river) and maximum runup (39 m) at Rikuzentakata estimated from satellite data agree closely with the 39.7 m inundation reported in the field. Here the ria coastal morphology and horn shaped bay enhanced the tsunami runup and effects. The Sendai coastal plain shows large inundation distances (6 km) and lower runup heights. Natori City and Wakabayashi Ward, on the Sendai plain, have similar runup values (12 and 16 m, respectively) obtained from SRTM data; these are comparable to those obtained from field surveys (12 and 9.5 m). However, at Yagawahama and Oyagawahama, Miyagi Prefecture, both SRTM and ASTER data provided maximum runup heights (41 to 45 m and 33 to 34 m, respectively), which are higher than those measured in the field (about 27 m). This difference in DEM and field data is associated with ASTER and SRTM DEM’s pixel size and vertical accuracy, the latter being dependent on ground coverage, slope, aspect and elevation. Countries with less access to technology and infrastructure can benefit from the use of satellite imagery and freely available DEMs for an initial, pre-field surveys, rapid estimate of inundated areas, distances and runup, and for assisting in hazard management and mitigation after a natural disaster.  相似文献   

4.
The major (M w = 8.8) Chilean earthquake of 27 February 2010 generated a trans-oceanic tsunami that was observed throughout the Pacific Ocean. Waves associated with this event had features similar to those of the 1960 tsunami generated in the same region by the Great (M w = 9.5) 1960 Chilean Earthquake. Both tsunamis were clearly observed on the coast of British Columbia. The 1960 tsunami was measured by 17 analog pen-and-paper tide gauges, while the 2010 tsunami was measured by 11 modern digital coastal tide gauges, four NEPTUNE-Canada bottom pressure recorders located offshore from southern Vancouver Island, and two nearby open-ocean DART stations. The 2010 records were augmented by data from seven NOAA tide gauges on the coast of Washington State. This study examines the principal characteristics of the waves from the 2010 event (height, period, duration, and arrival and travel times) and compares these properties for the west coast of Canada with corresponding properties of the 1960 tsunami. Results show that the 2010 waves were approximately 3.5 times smaller than the 1960 waves and reached the British Columbia coast 1 h earlier. The maximum 2010 wave heights were observed at Port Alberni (98.4 cm) and Winter Harbour (68.3 cm); the observed periods ranged from 12 min at Port Hardy to 110–120 min at Prince Rupert and Port Alberni and 150 min at Bamfield. The open-ocean records had maximum wave heights of 6–11 cm and typical periods of 7 and 15 min. Coastal and open-ocean tsunami records revealed persistent oscillations that “rang” for 3–4 days. Tsunami energy occupied a broad band of periods from 3 to 300 min. Estimation of the inverse celerity vectors from cross-correlation analysis of the deep-sea tsunami records shows that the tsunami waves underwent refraction as they approached the coast of Vancouver Island with the direction of the incoming waves changing from an initial direction of 340° True to a direction of 15° True for the second train of waves that arrived 7 h later after possible reflection from the Marquesas and Hawaiian islands.  相似文献   

5.
—Whereas the coast of Peru south of 10°S is historically accustomed to tsunamigenic earthquakes, the subduction zone north of 10°S has been relatively quiet. On 21 February 1996 at 21:51 GMT (07:51 local time) a large, tsunamigenic earthquake (Harvard estimate M w = 7.5) struck at 9.6°S, 79.6°W, approximately 130 km off the northern coast of Peru, north of the intersection of the Mendaña fracture zone with the Peru–Chile trench. The likely mechanism inferred from seismic data is a low-angle thrust consistent with subduction of the Nazca Plate beneath the South American plate, with relatively slow rupture characteristics. Approximately one hour after the main shock, a damaging tsunami reached the Peruvian coast, resulting in twelve deaths. We report survey measurements, from 7.7°S to 11°S, on maximum runup (2–5m, between 8 and 10°S), maximum inundation distances, which exceeded 500 m, and tsunami sediment deposition patterns. Observations and numerical simulations show that the hydrodynamic characteristics of this event resemble those of the 1992 Nicaragua tsunami. Differences in climate, vegetation and population make these two tsunamis seem more different than they were. This 1996 Chimbote event was the first large (M w >7) subduction-zone (interplate) earthquake between about 8 and 10°S, in Peru, since the 17th century, and bears resemblance to the 1960 (M w 7.6) event at 6.8°S. Together these two events are apparently the only large subduction-zone earthquakes in northern Peru since 1619 (est. latitude 8°S, est. M w 7.8); these two tsunamis also each produced more fatalities than any other tsunami in Peru since the 18th century. We concur with Pelayo and Wiens (1990, 1992) that this subduction zone, in northern Peru, resembles others where the subduction zone is only weakly coupled, and convergence is largely aseismic. Subduction-zone earthquakes, when they occur, are slow, commonly shallow, and originate far from shore (near the tip of the wedge). Thus they are weakly felt, and the ensuing tsunamis are unanticipated by local populations. Although perhaps a borderline case, the Chimbote tsunami clearly is another wake-up example of a "tsunami earthquake."  相似文献   

6.
We calculated tsunami runup probability (in excess of 0.5 m) at coastal sites throughout the Caribbean region. We applied a Poissonian probability model because of the variety of uncorrelated tsunami sources in the region. Coastlines were discretized into 20 km by 20 km cells, and the mean tsunami runup rate was determined for each cell. The remarkable ~500-year empirical record compiled by O’Loughlin and Lander (2003) was used to calculate an empirical tsunami probability map, the first of three constructed for this study. However, it is unclear whether the 500-year record is complete, so we conducted a seismic moment-balance exercise using a finite-element model of the Caribbean-North American plate boundaries and the earthquake catalog, and found that moment could be balanced if the seismic coupling coefficient is c = 0.32. Modeled moment release was therefore used to generate synthetic earthquake sequences to calculate 50 tsunami runup scenarios for 500-year periods. We made a second probability map from numerically-calculated runup rates in each cell. Differences between the first two probability maps based on empirical and numerical-modeled rates suggest that each captured different aspects of tsunami generation; the empirical model may be deficient in primary plate-boundary events, whereas numerical model rates lack backarc fault and landslide sources. We thus prepared a third probability map using Bayesian likelihood functions derived from the empirical and numerical rate models and their attendant uncertainty to weight a range of rates at each 20 km by 20 km coastal cell. Our best-estimate map gives a range of 30-year runup probability from 0–30% regionally.  相似文献   

7.
We report the statistical and wavelet analyses of the 21 May 2003 tsunami produced by an M w 6.8–6.9 thrust earthquake in the western Mediterranean Sea using 19 tide gauge records. The largest trough-to-crest wave height was 196 cm recorded at the Sant Antoni station in the lee of the incoming tsunami wave. Except at one station, the first wave was not the largest wave at all the analyzed stations, and the largest wave arrived several hours after the first arrival. In addition, the tsunami waves persisted for more than 1 day at most stations. As the spectra of coastal tide gauge stations are strongly influenced by topographic features, special care was taken here while interpreting the results of spectral and wavelet analysis. Our wavelet analysis shows that only a peak at around 23 min is persistent for long duration, and other peaks at 14, 30, 45, and 60 min appeared at short durations. The 23-min signal is possibly associated with the width of the source fault whereas the fault length contributed to the 45-min signal. Based on these dominant periods, the tsunami source dimensions are estimated as 95 km × 45 km. The statistical and wavelet analyses performed here provide some new insights into the characteristics of the tsunami that was generated and propagated in the western Mediterranean basin.  相似文献   

8.
The dense broadband seismic network provides more high-quality waveform that is helpful to improve constraint focal depth of shallow earthquake. Many shallow earthquakes occurring in sediment were regarded as induced events. In Sichuan basin, gas industry and salt mining are dependent on fluid injection technique that triggers microseismicity. We adopted waveform inversion method with regional records to obtain focal mechanism of an M s4.8 earthquake at Changning. The result suggested that the Changning earthquake occurred at a ESE thrust fault, and its focal depth was about 3 km. The depth phases including teleseismic pP phase and regional sPL phase shows that the focal depth is about 2 km. The strong, short-period surface wave suggests that this event is a very shallow earthquake. The amplitude ratio between Rayleigh wave and direct S wave was also used to estimate the source depth of the mainshock. The focal depth (2–4 km) is far less than the depth of the sedimentary layer thickness (6–8 km) in epicentral region. It is close to the depth of fluid injection of salt mining, which may imply that this event was triggered by the industrial activity.  相似文献   

9.
Tsunami Warning Centers issue rapid and accurate tsunami warnings to coastal populations by estimating the location and size of the causative earthquake as soon as possible after rupture initiation. Both US Tsunami Warning Centers have therefore been using Mwp to issue Tsunami Warnings 5–10 min after Earthquake origin time since 2002. However, because Mwp (Tsuboi et al., Bulletin of the Seismological society of America 85:606–613, 1995) is based on the far-field approximation to the P-wave displacement due to a double couple point source, we should only very carefully apply Mwp to data obtained in the near field, at distances of less than a few wavelengths from the fault. On the other hand, the surface waves from Great Earthquakes, including those that occur just offshore of populated areas, such as the 2011 Tohoku earthquake, clip seismographs located near the fault. Because the first arriving P-waves from such large events are often on scale, Mwp should provide useful information, even for these Great Earthquakes. We therefore calculate Mwp from 18 unclipped STS-1 broadband P-wave seismograms, recorded at 2–15° distance from the Tohoku epicenter to determine if Mwp can usefully estimate Mw for this earthquake, using data obtained close to the epicenter. In this case there should be a good chance to get reliable Mwp values for stations at epicentral distances of 9–10°, since the source duration for the Tohoku earthquake is less than 200 s and the time window used to estimate Mwp is 120 s in duration. Our analysis indicates that Mwp does indeed give reliable results (Mw ~ 9.1) beginning at about 11° distance from the epicenter. The values of Mwp from seismic waveforms obtained at 11–15° epicentral distance from the Mw 9.1 off the east coast of Tohuku earthquake of March 11, 2011 fell within the range 9.1–9.3, and were available within 4–5 min after origin time. Even the Mwp values of 7.7–8.4, obtained at less than 5° epicentral distance, exceed the PTWC’s threshold of Mw 7.6 for issuing a regional tsunami warning to coastal populations within 1,000 km of the epicenter, and of Mw 6.9 for issuing a local tsunami warning to the coastal populations of Hawaii.  相似文献   

10.
We modeled a tsunami from the West Papua, Indonesia earthquakes on January 3, 2009 (M w?=?7.7). After the first earthquake, tsunami alerts were issued in Indonesia and Japan. The tsunami was recorded at many stations located in and around the Pacific Ocean. In particular, at Kushimoto on Kii Peninsula, the maximum amplitude was 43?cm, larger than that at Manokwari on New Guinea Island, near the epicenter. The tsunami was recorded on near-shore wave gauges, offshore GPS sensors and deep-sea bottom pressure sensors. We have collected more than 150 records and used 72 stations?? data with clear tsunami signals for the tsunami source modeling. We assumed two fault models (single fault and five subfaults) which are located to cover the aftershock area. The estimated average slip on the single fault model (80?×?40?km) is 0.64?m, which yields a seismic moment of 1.02?×?1020?Nm (M w?=?7.3). The observed tsunami waveforms at most stations are well explained by this model.  相似文献   

11.
Immediately following the M S7.0 Lushan earthquake on April 20, 2013, using high-pass and low-pass filtering on the digital seismic stations in the Shanxi Province, located about 870–1,452 km from the earthquake epicenter, we detected some earthquakes at a time corresponding to the first arrival of surface waves in high-pass filtering waveform. The earthquakes were especially noticed at stations in Youyu (YUY), Shanzizao (SZZ), Shanghuangzhuang (SHZ), and Zhenchuan (ZCH), which are located in a volcanic region in the Shanxi Province,but they were not listed in the Shanxi seismic observation report. These earthquakes occurred 4–50 min after the passage of the maximum amplitude Rayleigh wave, and the periods of the surface waves were mainly between 15 and 20 s following. The Coulomb stresses caused by the Rayleigh waves that acted on the four stations was about 0.001 MPa, which is a little lower than the threshold value of dynamic triggering, therefore, we may conclude that the Datong volcanic region is more sensitive to the Coulomb stress change. To verify, if the similar phenomena are widespread, we used the same filtering to observe contrastively continuous waveform data before, and 5 h after, the M S7.0 Lushan earthquake and M S9.0 Tohoku earthquake in 2011. The results show that the similar phenomena occur before the earthquakes, but the seismicity rates after the earthquakes are remarkably increased. Since these weak earthquakes are quite small, it is hard to get clear phase arrival time from three or more stations to locate them. In addition, the travel time differences between P waves and S waves (S–P) are all less than 4 s, that means the events should occur in 34 km around the stations in the volcanic region. The stress of initial dynamic triggering of the M S9.0 Tohoku earthquake was about 0.09 MPa, which is much higher than the threshold value of dynamic triggering stress. The earthquakes after the M S9.0 Tohoku earthquake are related to dynamic triggering stress, but the events before the earthquake cannot be linked to seismic events, but may be related to the background seismicity or from other kinds of local sources, such as anthropogenic sources (i.e., explosions). Using two teleseismic filtering, the small background earthquakes in the Datong volcanic region occur frequently, thus we postulate that previous catalog does not apply bandpass filter to pick out the weak earthquakes, and some of the observed weak events were not triggered by changes in the dynamic stress field.  相似文献   

12.
On March 11th 2011 a M w 9.0 mega-thrust interface subduction earthquake, the Great East Japan Earthquake, occurred 130 km off the northeast coast of Japan in the Pacific Ocean at the Japan Trench, triggering tsunami which caused damage along 600 km of coastline. Observations of damage to buildings (including vertical evacuation facilities) and coastal defences in Tōhoku are presented following investigation by the Earthquake Engineering Field Investigation Team (EEFIT) at 10 locations in Iwate and Miyagi Prefectures. Observations are presented in the context of the coastal setting and tsunami characteristics experienced at each location. Damage surveys were carried out in Kamaishi City and Kesennuma City using a damage scale for reinforced concrete (RC), timber and steel frame buildings adapted from an earlier EEFIT tsunami damage scale. Observations show that many sea walls and breakwaters were overtopped, overturned, or broken up, but provided some degree of protection. We show the extreme variability of damage in a local area due to inundation depth, flow direction, velocity variations and sheltering. Survival of many RC shear wall structures shows their high potential to withstand local earthquake and significant tsunami inundation but further research is required into mitigation of scour, liquefaction, debris impact, and the prevention of overturning failure. Damage to steel and timber buildings are also discussed. These observations are intended to contribute to mitigation of future earthquake and tsunami damage by highlighting the key features which influence damage level and local variability of damage sustained by urban coastal infrastructure when subjected to extreme tsunami inundation depths.  相似文献   

13.
We use a viscous slide model of Jiang and LeBlond (1994) coupled with nonlinear shallow water equations to study tsunami waves in Resurrection Bay, in south-central Alaska. The town of Seward, located at the head of Resurrection Bay, was hit hard by both tectonic and local landslide-generated tsunami waves during the M W 9.2 1964 earthquake with an epicenter located about 150 km northeast of Seward. Recent studies have estimated the total volume of underwater slide material that moved in Resurrection Bay during the earthquake to be about 211 million m3. Resurrection Bay is a glacial fjord with large tidal ranges and sediments accumulating on steep underwater slopes at a high rate. Also, it is located in a seismically active region above the Aleutian megathrust. All these factors make the town vulnerable to locally generated waves produced by underwater slope failures. Therefore it is crucial to assess the tsunami hazard related to local landslide-generated tsunamis in Resurrection Bay in order to conduct comprehensive tsunami inundation mapping at Seward. We use numerical modeling to recreate the landslides and tsunami waves of the 1964 earthquake to test the hypothesis that the local tsunami in Resurrection Bay has been produced by a number of different slope failures. We find that numerical results are in good agreement with the observational data, and the model could be employed to evaluate landslide tsunami hazard in Alaska fjords for the purposes of tsunami hazard mitigation.  相似文献   

14.
We studied two tsunamis from 2012, one generated by the El Salvador earthquake of 27 August (Mw 7.3) and the other generated by the Philippines earthquake of 31 August (Mw 7.6), using sea level data analysis and numerical modeling. For the El Salvador tsunami, the largest wave height was observed in Baltra, Galapagos Islands (71.1 cm) located about 1,400 km away from the source. The tsunami governing periods were around 9 and 19 min. Numerical modeling indicated that most of the tsunami energy was directed towards the Galapagos Islands, explaining the relatively large wave height there. For the Philippines tsunami, the maximum wave height of 30.5 cm was observed at Kushimoto in Japan located about 2,700 km away from the source. The tsunami governing periods were around 8, 12 and 29 min. Numerical modeling showed that a significant part of the far-field tsunami energy was directed towards the southern coast of Japan. Fourier and wavelet analyses as well as numerical modeling suggested that the dominant period of the first wave at stations normal to the fault strike is related to the fault width, while the period of the first wave at stations in the direction of fault strike is representative of the fault length.  相似文献   

15.
Evaluating Tsunami Hazard in the Northwestern Indian Ocean   总被引：1，自引：0，他引：1  
We evaluate here the tsunami hazard in the northwestern Indian Ocean. The maximum regional earthquake calculated from seismic hazard analysis, was used as the characteristic earthquake for our tsunami hazard assessment. This earthquake, with a moment magnitude of M w 8.3 and a return period of about 1000 years, was moved along the Makran subduction zone (MSZ) and its possible tsunami wave height along various coasts was calculated via numerical simulation. Both seismic hazard analysis and numerical modeling of the tsunami were validated using historical observations of the Makran earthquake and tsunami of the 1945. Results showed that the possible tsunami may reach a maximum height of 9.6 m in the region. The distribution of tsunami wave height along various coasts is presented. We recommend the development of a tsunami warning system in the region, and emphasize the value of education as a measure to mitigate the death toll of a possible tsunami in this region.  相似文献   

16.
以马尼拉海沟的北断层发生MW8.0地震在南海引发海啸为假想的模拟情景, 利用E-FAST法定量分析了COMCOT海啸数值模型输出(最大海啸波高)对震级, 震源深度, 震中位置和断层走向、 倾角、 滑动角等震源参数的敏感性, 以及各震源参数间的交互效应对最大海啸波高的影响. 结果表明, 观测点B1( 20.1°N, 119.4°E)、 B2(18.4°N, 118.1°E)和B3(13.5°N, 117.6°E)的最大海啸波高都对震级十分敏感, 对震中位置、 断层走向和倾角较为敏感. 敏感的震源参数在影响上述3个观测点的最大海啸波高时, 与其它震源参数产生了较强的交互效应. 但是对于不同的观测点, 各震源参数的重要度排序则存在一定的差异. 该分析结果有助于更好地认识海啸波高与潜在海啸源参数之间的关系.   相似文献   

17.
This study investigates the kinematics of the rupture process of the M L 7.3 Chi–Chi, Taiwan, earthquake on September 21, 1999. By applying the proposed hybrid homomorphic deconvolution method to deconvolve teleseismic broadband P-wave displacement recordings of the earthquake, this study derives the apparent source time functions (ASTFs) at ten stations located around the epicenter. To further characterize the fault, the kinematic history of the rupture was inverted from ASTFs using a genetic algorithm, coupled with nonlinear iterative technique. The calculated ASFTs reveal that the total rupture event lasted for approximately 27 s. Static slip distribution images indicate that most slip occurred at shallower portions of the fault plane, especially 20–55 km north of the epicenter. The maximum slip reached 20 m at 45 km north of the epicenter, and the average slip throughout the observed rupture area was approximately 2 m. Large asperities on the fault appeared at 25–35 km and 40–50 km north of the hypocenter, and coincided with relatively high rupture velocity. This suggests that the earthquake’s energy may have been released quickly. The rupture velocity decreased upon encountering an asperity, and increased again after passing the asperity. This implies that the rupture required more time to overcome the resistances of the asperities. The maximum rupture velocity was 3.8 km/s, while the average rupture velocity was approximately 2.2 km/s. The rise time distribution suggests that larger slip amplitudes generally correspond to shorter rise times on the subfaults.  相似文献   

18.
The tsunami generated by the 2011 Tohoku Earthquake (M w = 9.0) reached maximum heights of about 5 m along the coast of the Kuril Islands. The most essential feature of this event was sea ice about 0.5 m thick moved by the ocean water. The tsunami did not cause any essential damage on the Kuril Islands, but significantly affected coastal zones and produced interesting effects. The problem of a tsunami accompanied by marine ice is discussed and illustrated with photos.  相似文献   

19.
Probabilistic Assessment of Tsunami Recurrence in the Indian Ocean   总被引：1，自引：0，他引：1  
The Indian Ocean is one of the most tsunamigenic regions of the world and recently experienced a mega-tsunami in the Sumatra region on 26 December 2004 (M W 9.2 earthquake) with tsunami intensity I (Soloviev-Imamura intensity scale) equal to 4.5, causing heavy destruction of lives and property in the Indian Ocean rim countries. In this study, probabilities of occurrences of large tsunamis with tsunami intensities I ≥ 2.0 and I ≥ 3.0 (average wave heights H ≥ 2.83 m and H ≥ 5.66 m, respectively) during a specified time interval were calculated using three stochastic models, namely, Weibull, gamma and lognormal. Tsunami recurrence was calculated for the whole Indian Ocean and the special case of the Andaman-Sumatra-Java (ASJ) region, excluding the 1945 Makran event from the main data set. For this purpose, a reliable, homogeneous and complete tsunami catalogue with I ≥ 2.0 during the period 1797–2006 was used. The tsunami hazard parameters were estimated using the method of maximum likelihood. The logarithm of likelihood function (ln L) was estimated and used to test the suitability of models in the examined region. The Weibull model was observed to be the most suitable model to estimate tsunami recurrence in the region. The sample mean intervals of occurrences of tsunamis with intensity I ≥ 2.0 and I ≥ 3.0 were calculated for the observed data as well as for the Weibull, gamma and lognormal models. The estimated cumulative and conditional probabilities in the whole Indian Ocean region show recurrence periods of about 27–30 years (2033–2036) and 35–36 years (2039–2040) for tsunami intensities I ≥ 2.0 and I ≥ 3.0, respectively, while it is about 31–35 years (2037–2041) and 41–42 years (2045–2046) for a tsunami of intensity I ≥ 2.0 and I ≥ 3.0, respectively, in the ASJ region. A high probability (>0.9) of occurrence of large tsunamis with I ≥ 2.0 in the next 30–40 years in the Indian Ocean region was revealed.  相似文献   

20.
Tsunamis are most destructive at near to regional distances, arriving within 20–30 min after a causative earthquake; effective early warning at these distances requires notification within 15 min or less. The size and impact of a tsunami also depend on sea floor displacement, which is related to the length, L, width, W, mean slip, D, and depth, z, of the earthquake rupture. Currently, the primary seismic discriminant for tsunami potential is the centroid-moment tensor magnitude, M w CMT , representing the product LWD and estimated via an indirect inversion procedure. However, the obtained M w CMT and the implied LWD value vary with rupture depth, earth model, and other factors, and are only available 20–30 min or more after an earthquake. The use of more direct discriminants for tsunami potential could avoid these problems and aid in effective early warning, especially for near to regional distances. Previously, we presented a direct procedure for rapid assessment of earthquake tsunami potential using two, simple measurements on P-wave seismograms—the predominant period on velocity records, T d , and the likelihood, T 50 Ex , that the high-frequency, apparent rupture-duration, T 0, exceeds 50–55 s. We have shown that T d and T 0 are related to the critical rupture parameters L, W, D, and z, and that either of the period–duration products T d T 0 or T d T 50 Ex gives more information on tsunami impact and size than M w CMT , M wp, and other currently used discriminants. These results imply that tsunami potential is not directly related to the product LWD from the “seismic” faulting model, as is assumed with the use of the M w CMT discriminant. Instead, information on rupture length, L, and depth, z, as provided by T d T 0 or T d T 50 Ex , can constrain well the tsunami potential of an earthquake. We introduce here special treatment of the signal around the S arrival at close stations, a modified, real-time, M wpd(RT) magnitude, and other procedures to enable early estimation of event parameters and tsunami discriminants. We show that with real-time data currently available in most regions of tsunami hazard, event locations, m b and M wp magnitudes, and the direct, period–duration discriminant, T d T 50 Ex can be determined within 5 min after an earthquake occurs, and T 0, T d T 0, and M wpd(RT) within approximately 10 min. This processing is implemented and running continuously in real-time within the Early-est earthquake monitor at INGV-Rome (http://early-est.rm.ingv.it). We also show that the difference m b  ? log10(T d T 0) forms a rapid discriminant for slow, tsunami earthquakes. The rapid availability of these measurements can aid in faster and more reliable tsunami early warning for near to regional distances.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号