共查询到20条相似文献，搜索用时 968 毫秒
1.
G. J. F. Holden 《The Photogrammetric Record》1968,6(31):41-48
The article describes a method of strip aerial triangulation using the Wild B8 plotter. The principal feature of the method is the transfer of exterior orientation of a camera by measurement of outer orientation parallel to successive airbases. 相似文献
2.
3.
多影像空三平差辅助下的车载全景相机严密标定方法 总被引：1，自引：0，他引：1
针对目前全景相机标定方法的研究现状,提出了一种多影像光束法空三平差辅助下的全景相机内参数严密标定方法。首先建立全景相机标定场,对组成全景相机的每台单相机的内参数进行标定;然后按照预先设计好的摄影参数,旋转摄影获取全景相机在标定场中多个不同摄影方向的影像,利用其中一个摄站的标定影像和物方控制点通过空间后方交会的方法解算单相机之间的初始相对方位元素,即粗标定;最后将所有摄站的标定影像构建区域网并进行光束法空三平差,获取精确的全景相机参数,即严密标定。试验表明,文中提出的全景相机标定方法可以提高标定结果的精度和可靠性,为全景影像的拼接、量测及真彩点云的生成等后续研究和应用奠定可靠的基础。 相似文献
4.
5.
异轨遥感立体像对外方位元素的求解算法 总被引：4，自引：1，他引：4
在对异轨遥感立体像对外方位元素求解的基本模型进行系统阐述的基础上 ,讨论了基于共面条件的后方交会模型改化方法及其和基于共线方程的后方交会模型的融合。给出了外方位元素初值求解的实用算法 ,并利用实测立体像对数据进行了联合平差计算 ,取得了较好的结果 相似文献
6.
轻小型组合宽角低空相机检校技术研究 总被引：1，自引：0，他引：1
轻小型组合宽角低空相机由四个非量测的CCD面阵相机组合而成,其内方位元素未知,并且相机畸变差较大.而无人机航空摄影测量作业对CCD相机的光学畸变参数有较高的要求,因为参数的一个像素的误差常常会导致地面几米甚至数十米的误差,因此对组合相机进行高精度检校是无人机航空摄影测量作业的关键步骤.本文采用多片空间后方交会方法在室外... 相似文献
7.
Albert K. Chong 《The Photogrammetric Record》2004,19(108):296-310
Generally, a low-cost image-based motion study system consists of a set of two or more video imaging cameras and a set of object space control targets. The control targets are required to provide for the computation of exterior parameters of the video frames of objects in motion. Subsequently, the computed exterior orientation parameters are used to compute the position of the motion targets. In general, the accuracy of the motion data is dependent largely on the accuracy of the 3D coordinates of the control targets, the computed camera and lens parameters and the frame rate of the camera. Obviously, it is difficult to improve the frame rate of a low-cost camera; however, the other factors may be optimised analytically. Optimising the accuracy of the control targets is a straightforward process and is discussed briefly in the paper. Optimising the computed camera and lens parameters was the main focus of the research. Consequently, the paper provides the detail of the developed optimising technique. The results show that an optimal principal distance and other lens parameters can be determined by analysing the error of a set of highly accurate object distances. The evaluation shows that the accuracy of the video motion study system can be improved by as much as six times or a reduction of scaling error from 1·06 to 1·01. 相似文献
8.
数码相机的标定参数包括相机的内方位元素和各项镜头畸变差。从摄影测量的理论出发,通过空间前方交会试验,分析并统计了相机标定的各参数对摄影测量精度的影响。 相似文献
9.
The determination of the attitude, the position and the intrinsic geometric characteristics of the camera is recognised as the fundamental photogrammetric problem. It can be summarised as the determination of camera interior and exterior orientation parameters, as well as the determination of 3D coordinates of object points. The term "exterior orientation"of an image refers to its position and orientation related to an exterior (object space) coordinate system. Several methods can be applied to determine the parameters of the orientation of one, two or more photos. The orientation can be processed in steps (as relative and absolute orientation) but simultaneous methods (such as bundle adjustments) are now available in many software packages. Several methods have also been developed for the orientation of single images. They are based in general on geometric and topological characteristics of imaged objects.
This paper presents a survey of classical and modern methods for the determination of the exterior parameters in photogrammetry, some of which are available as software packages (with practical examples) on the Internet. The methods presented are classified in three principal groups. In the first, a selection of approximate methods for applications that do not require great accuracy is presented. Such methods are also used to calculate values required for iterative processes. In the second group, standard point–based methods derived from collinearity, coplanarity or coangularity conditions are briefly reviewed, followed by line–based approaches. The third group represents orientation methods based on constraints and on concepts of projective geometry, which are becoming of increasing interest for photogrammetrists. In the last section, the paper gives a summary of existing strategies for automatic exterior orientation in aerial photogrammetry. 相似文献
This paper presents a survey of classical and modern methods for the determination of the exterior parameters in photogrammetry, some of which are available as software packages (with practical examples) on the Internet. The methods presented are classified in three principal groups. In the first, a selection of approximate methods for applications that do not require great accuracy is presented. Such methods are also used to calculate values required for iterative processes. In the second group, standard point–based methods derived from collinearity, coplanarity or coangularity conditions are briefly reviewed, followed by line–based approaches. The third group represents orientation methods based on constraints and on concepts of projective geometry, which are becoming of increasing interest for photogrammetrists. In the last section, the paper gives a summary of existing strategies for automatic exterior orientation in aerial photogrammetry. 相似文献
10.
This work describes a calibration process for inexpensive consumer cameras integrated into a low cost and compact aerial multi-view imager for remote sensing and photogrammetry. The main advantage of this design is to make the filming component lightweight and rapidly deployable, as well as reducing cost when compared with mainstream commercial oblique imagery. An in situ flight test was carried out in Guiyang. In that experiment, a meridian convergence-based approach was adopted to adjust preprocessing, the residue error and the captured images’ exterior orientation linear and angular parameters were calculated by means of the direct geo-referencing approach yielding a favorable outcome for exterior orientation linear parameters of the camera, around 0.2–0.3 m deviation from the actual measured results at 1000 m flight above ground level. The camera’s exterior orientation angular parameters φ, ω whose difference compared with the standard aerial aero triangulation approach reached a high accuracy level within the intended endurance of 0.005°. These results indicate that the compact implementation of the oblique aerial imager comprised of consumer level off-the-shelf digital cameras achieved competitive accuracy at a low cost and high versatility. 相似文献
11.
数码相机检验中出现的问题及解决方法 总被引：1，自引：0，他引：1
数码相机的检验是近景摄影测量中经常碰到的问题。最常用的主要还是基于共线方程的后方交会法。但由于普通数码相机存在较大的镜头畸变,内方位元素也未知,所以仅用单片进行后方交会求取有关参数时,法方程可能会出现病态现象,从而影响最后的检验结果。文中对此现象进行了讨论,并给出了一些实用的解决方法。 相似文献
12.
针对众多非量测单相机的检校方法,通过分析数码相机的误差来源,并考虑相机的内、外方位元素和物镜光学畸变等因素引起的误差,提出一种基于类似棋盘检校场的数字相机检校方法。利用共线方程和二维DLT之间的关系导出了由二维DLT的9个参数表达的主纵线方程,构建同形矩阵,通过不同摄站拍摄目标的多幅影像,求得内、外方位元素的初始值,并由多张影像的空间后方交会求出相机需要检校参数,再由假设检验来检验相机系统参数的显著性。经实例分析表明,利用改进后的方法求解参数的精度满足实际需求,且效率更高。 相似文献
13.
非量测数码相机由于价格低廉、使用方便等原因成为近景摄影测量获取影像的主要设备之一。但非量测相机的内方位元素和畸变系数未知,不能直接利用共线方程进行解析计算,因而必须对相机进行检校。而相机参数检校成果质量的高低直接关系着能否满足测量精度的要求。本文提出了基于二维直接线性变换(DLT)的相机标定算法,利用平面控制点解算出像点坐标和相应物点物方空间坐标之间的线性关系,再结合内方位元素及畸变参数的解算进行迭代,以得到满足一定精度要求的相机参数(x0,y0,f,k1,k2,p1,p2),并用MATLAB加以实现。 相似文献
14.
Procedures for the calibration of a stereopair simultaneously with a bundle adjustment are presented. Distances and directions in object space are used as additional observations. The analytical simultaneous calibration of a photogrammetric camera is essential when instrument methods do not determine the precalibrated parameters of interior orientation with sufficient accuracy. 相似文献
15.
介绍了针对四拼数码航空相机的附加约束条件光束法区域网平差原理,包括计算四拼相机外方位元素,并同时计算四台子相机的相对位置关系,获取四拼相机平台检校参数。实验结果表明采用这种方法计算出来的平台检校参数精度高,生成的虚拟影像拼接效果好,测图精度满足大中比例尺地形图规范要求。 相似文献
16.
为了找到适合天绘一号卫星三线阵相机在轨几何精化的模型和算法,首先分析了外方位线元素误差在几何参数精化中的影响,然后通过对定姿数据的预处理,消除了其中含有的高频噪声,并用正弦函数补偿了卫星平台飞行过程中的低频抖动,为三线阵相机每个镜头设计了姿态角常差模型。此外,根据传统的附加参数模型,构建了直接以像素坐标为观测值的内方位元素模型,并使用单侧有控外推的方式,确定最佳的精化模型参数组合及求解策略。试验表明,采用本文的精化方案,利用合理分布的控制点,天绘一号能达到平面精度约1 GSD,高程精度约0.8 GSD。 相似文献
17.
18.
Commercial digital photogrammetric software has been applied to convergent stereoscopic photography of human tooth replicas prepared to exhibit optical texture resulting in successful generation of 3D coordinate data. Tooth replicas were imaged using a semi-metric 35 mm camera and f = 100 mm macro lens on extension bellows. Model precision was within acceptable limits of 12 μ m or better for manual target matching and 21 μ m or better for automatic image matching. Further improvement in optical texture is required to achieve automatic image matching precision comparable to that of manual target matching. Small errors in interior orientation parameters attributed to instability in the bellows as well as small errors in the relative orientation resulted in some systematic errors. The use of a fixed camera lens system is expected to reduce these errors. When combined with commercially available, moderately priced, digital SLR cameras this brings 3D model generation closer to everyday clinical dental practice. 相似文献
19.
20.
W. E. Sly 《The Photogrammetric Record》1968,6(31):59-74
Two experimental procedures for aerial survey camera calibration using respectively a Wild TA theodolite and a modified Cooke, Trough ton and Simms geodetic theodolite are described. The procedures determine radial distortion only; tangential distortion is assumed to be negligible. Details of a graphical method of computing the results are given in an appendix. 相似文献