共查询到20条相似文献，搜索用时 859 毫秒
1.
针对地震槽波在低速层的传播特性,开展了煤层内地震槽波勘探的数值模拟和物理模拟研究的初探工作.在数值模拟研究方面,采用交错网格有限差分法对煤层中的地震槽波进行三分量全波场模拟.基于波场快照和人工合成地震记录研究了不同模型中的波场特征和各种波型的传播规律.在物理模拟方面,通过选用不同配比的环氧树脂和硅橡胶类材料构建地震槽波物理模型,利用透射法和反射法观测系统获得了清晰的地震槽波记录以研究槽波的地震学特征.研究表明,在煤层内槽波的地震波场中,Love型槽波的能量小于Rayleigh型槽波的SV分量,大于Rayleigh型槽波的SH分量.相对于Love型槽波和Rayleigh型槽波的SH分量,Rayleigh型槽波的SV分量在围岩中的泄露能量较强.在煤层界面附近的围岩中,地震波仍以槽波形式传播,随着距离的增加能量逐渐衰减.随着煤层变薄,煤层槽波主频向高频方向移动,频散现象增强,传播速度增大. 相似文献
2.
New alternative formulations of exact boundary conditions for arbitrary three-dimensional (3D) free-surface topographies on seismic media have been derived. They are shown to be equivalent to previously published formulations, thereby verifying the validity of each set of formulations. The top of a curved grid represents the free-surface topography while the interior of the grid represents the physical medium. We assume the velocity–stress version of the viscoelastic wave equations to be valid in this grid before transforming the equations to a rectangular grid. In order to perform the numerical discretization we apply the latter version of the equations for seismic wave propagation simulation in the medium. The numerical discretization of the free-surface topography boundary conditions by second-order finite differences (FDs) is shown, as well as the spatially unconditional stability of the resulting system of equations. The FD order is increased by two for each point away from the free surface up to eight, which is the order used in the interior. We use staggered grids in both space and time and the second-order leap-frog and Crank– Nicholson methods for wavefield time propagation. An application using parameters typical of teleseismic earthquakes and explosions is presented using a 200 × 100 km2 area of real topography from southwestern Norway over a homogeneous medium. A dipping plane wave simulates a teleseismic P-wave incident on the surface topography. Results show conversion from P- to Rg- (short period fundamental mode Rayleigh) waves in the steepest and/or roughest topography, as well as attenuated waves in valleys and fjords. The codes are parallelized for simulation on fast supercomputers and PC-clusters to model high frequencies and/or large areas. 相似文献
3.
中国大陆中西部普遍具有强烈的地形起伏,起伏地形会对地震资料的处理分析产生严重干扰.精细处理起伏地形成为高精度地震成像的必然要求.传统方法通过填充低速介质将不规则模型扩展为规则模型来处理起伏地形.近年来,借助坐标变换将物理空间不规则模型转换为计算空间规则模型的地形平化方法,为解决起伏地形问题提供了新思路.本文基于经典的模型扩展和新发展的地形平化方法分别处理起伏地形,从走时正演、射线追踪和反演成像三个方面,全面细致地评判了两种地形处理方法在起伏地形层析成像中的适用性和有效性.结果表明,模型扩展中阶梯状近似和填充介质速度参与计算,会造成起伏地形走时计算精度损失,出现虚假射线路径和错误出射角,导致反演分辨率降低,成像结果模糊甚至失真;地形平化中采用贴体网格参数化,能够保证离散模型完全匹配起伏地形,并且保持起伏地形在物理空间和计算空间中均为自由表面.在此基础上发展的层析成像技术具有高度的保真性,有效地处理了地形起伏效应,为起伏地形区域精细速度成像提供了有力的技术保障. 相似文献
4.
A hybrid method combining finite element and 4th-order finite difference techniques is developed to model SH and P-SV seismic wave propagation in a 2D elastic medium with irregular surface topography. Both the classic staggered grid finite difference scheme and the partially staggered grid scheme are tested. The accuracy of the hybrid method is studied by comparison with a semi-analytical and another numerical method. Subsequently, to study the amplification, numerical simulations of seismic wave propagation in a series of hills are carried out and compared with the single-hill case. Depending on the position of the source in relation to the topography, the ratio between the heights and lengths of the hills or the ratio between the lengths of the hills and the wavelength, the presence of several hills as opposed to a single one can increase the amplification effect due to topography. This study highlights the fact that, when evaluating topographic site effects, surrounding topography must be taken into account in addition to local topography. 相似文献
5.
Seismic wavefield modeling in media with fluid-filled fractures and surface topography 总被引：3，自引：0，他引：3
We present a finite difference (FD) method for the simulation of seismic wave fields in fractured medium with an irregular (non-flat) free surface which is beneficial for interpreting exploration data acquired in mountainous regions. Fractures are introduced through the Coates-Schoenberg approach into the FD scheme which leads to local anisotropic properties of the media where fractures are embedded. To implement surface topography, we take advantage of the boundary-conforming grid and map a rectangular grid onto a curved one. We use a stable and explicit second-order accurate finite difference scheme to discretize the elastic wave equations (in a curvilinear coordinate system) in a 2D heterogeneous transversely isotropic medium with a horizontal axis of symmetry (HTI). Efficiency tests performed by different numerical experiments clearly illustrate the influence of an irregular free surface on seismic wave propagation in fractured media which may be significant to mountain seismic exploration. The tests also illustrate that the scattered waves induced by the tips of the fracture are re-scattered by the features of the free surface topography. The scattered waves provoked by the topography are re-scattered by the fractures, especially Rayleigh wave scattering whose amplitudes are much larger than others and making it very difficult to identify effective information from the fractures. 相似文献
6.
煤层中存在的裂隙会导致介质表现为各向异性,本文以HTI型煤层为例,结合各向异性介质弹性矩阵和各向异性裂隙理论,推导出不同充填物的垂直裂隙中各向异性参数表达式,将其应用于地震波响应分析;通过改进的交错网格差分法和各向异性Christoffel方程波场分解法,得到地震波合成记录和分解后的P波和SV波记录;将Thomsen群速度与相速度公式,经过坐标轴旋转变换,得到HTI型煤层中不同各向异性参数的地震波速度响应表达式;建立不同类型煤层地质模型,分析了裂隙密度、裂隙充填物以及煤层厚度等参数变化时的地震波响应特征.研究结果为分析垂向裂隙各向异性薄煤层地震波传播规律提供工具,为选用相应地震数据进行地震波各向异性参数反演提供依据. 相似文献
7.
8.
We have implemented a 3D finite‐difference scheme to simulate wave propagation in arbitrary anisotropic media. The anisotropic media up to orthorhombic symmetry were modelled using a standard staggered grid scheme and beyond (monoclinic and triclinic) using a rotated staggered grid scheme. The rationale of not using rotated staggered grid for all types of anisotropic media is that the rotated staggered grid schemes are more expensive than standard staggered grid schemes. For a 1D azimuthally anistropic medium, we show a comparison between the seismic data generated by our finite‐difference code and by the reflectivity algorithm; they are in excellent agreement. We conducted a study on zero‐offset shear‐wave splitting using the finite‐difference modelling algorithm using the rotated staggered grid scheme. Our S‐wave splitting study is mainly focused on fractured media. On the scale of seismic wavelenghts, small aligned fractures behave as an equivalent anisotropic medium. We computed the equivalent elastic properties of the fractures and the background in which the fractures were embedded, using low‐frequency equivalent media theories. Wave propagation was simulated for both rotationally invariant and corrugated fractures embedded in an isotropic background for one, or more than one, set of fluid‐filled and dry fractures. S‐wave splitting was studied for dipping fractures, two vertical non‐orthogonal fractures and corrugated fractures. Our modelling results confirm that S‐wave splitting can reveal the fracture infill in the case of dipping fractures. S‐wave splitting has the potential to reveal the angle between the two vertical fractures. We also notice that in the case of vertical corrugated fractures, S‐wave splitting is sensitive to the fracture infill. 相似文献
9.
Finite‐difference P‐SV simulations of seismic scattering characteristics of faulted coal‐seam models have been undertaken for near‐surface P‐ and S‐wave sources in an attempt to understand the efficiency of body‐wave to channel‐wave mode conversion and how it depends on the elastic parameters of the structure. The synthetic seismograms clearly show the groups of channel waves generated at the fault: one by the downgoing P‐wave and the other by the downgoing S‐wave. These modes travel horizontally in the seam at velocities less than the S‐wavespeed of the rock. A strong Airy phase is generated for the fundamental mode. The velocity contrast between the coal and the host rock is a more important parameter than the density contrast in controlling the amplitude of the channel waves. The optimal coupling from body‐wave energy to channel‐wave energy occurs at a velocity contrast of 1.5. Strong guided waves are produced by the incident S‐sources for source angles of 75° to 90° (close to the near‐side face of the fault). As the fault throw increases, the amplitude of the channel wave also increases. The presence of a lower‐velocity clay layer within the coal‐seam sequence affects the waveguiding characteristics. The displacement amplitude distribution is shifted more towards the lower‐wavespeed layer. The presence of a ‘washout’ zone or a brecciated zone surrounding the fault also results in greater forward scattering and channel‐wave capture by the coal seam. 相似文献
10.
对煤巷小构造地震波场进行了数值模拟研究,分析了层状煤层中地震波的传播特征.研究表明:(1)在煤巷迎头前方煤层内以纵波震源激发的Rayleigh型槽波相对于体波能量较强,波列较长,波速较低.(2)沿煤层传播的Rayleigh型槽波在小构造面上产生Rayleigh型槽波反射波,反射Rayleigh型槽波垂直分量相对于水平分量能量较强.沿煤层反向传播的反射Rayleigh型槽波在煤巷迎头面上转换为沿煤巷底板传播的Rayleigh面波.沿煤巷底板可以接收到能量较强的反射Rayleigh型槽波产生的Rayleigh面波,其可以作为超前探测小构造面的特征波.在地震记录上反射Rayleigh型槽波产生的Rayleigh面波波至最迟,在时间域与其他波列时间间隔较大,其垂直分量能量相对于水平分量较强,在地震记录上容易识别.(3)在相同的地质条件下应用反射地震超前探测方法,标志煤巷迎头前方存在小构造面的反射地震波能量较弱,受煤巷顶、底板界面和采煤迎头面的强反射波干扰,在地震记录中难以识别. 相似文献
11.
Wave-induced flow is observed as the dominated factor for P wave propagation at seismic frequencies. This mechanism has a mesoscopic scale nature. The inhomogeneous unsaturated patches are regarded larger than the pore size, but smaller than the wavelength. Surface wave, e.g., Rayleigh wave, which propagates along the free surface, generated by the interfering of body waves is also affected by the mesoscopic loss mechanisms. Recent studies have reported that the effect of the wave-induced flow in wave propagation shows a relaxation behavior. Viscoelastic equivalent relaxation function associated with the wave mode can describe the kinetic nature of the attenuation. In this paper, the equivalent viscoelastic relaxation functions are extended to take into account the free surface for the Rayleigh surface wave propagation in patchy saturated poroelastic media. Numerical results for the frequency-dependent velocity and attenuation and the time-dependent dynamical responses for the equivalent Rayleigh surface wave propagation along an interface between vacuum and patchy saturated porous media are reported in the low-frequency range (0.1–1,000 Hz). The results show that the dispersion and attenuation and kinetic characteristics of the mesoscopic loss effect for the surface wave can be effectively represented in the equivalent viscoelastic media. The simulation of surface wave propagation within mesoscopic patches requires solving Biot’s differential equations in very small grid spaces, involving the conversion of the fast P wave energy diffusion into the Biot slow wave. This procedure requires a very large amount of computer consumption. An efficient equivalent approach for this patchy saturated poroelastic media shows a more convenient way to solve the single phase viscoelastic differential equations. 相似文献
12.
13.
针对粘弹性裂隙型单斜介质,本文应用高阶交错网格差分法,对其传播快照以及多方位地面三分量记录进行模拟,结果证明了裂隙填充物的性质引起的各向异性与粘弹性性质对单斜介质波场有明显的影响,总结了不同观测方位地震记录呈现出的规律性,这为进一步了解波场在介质中的传播情况,提出更合理的理论模型,提供一种尝试. 相似文献
14.
The modelling of elastic waves in fractured media with an explicit finite‐difference scheme causes instability problems on a staggered grid when the medium possesses high‐contrast discontinuities (strong heterogeneities). For the present study we apply the rotated staggered grid. Using this modified grid it is possible to simulate the propagation of elastic waves in a 2D or 3D medium containing cracks, pores or free surfaces without hard‐coded boundary conditions. Therefore it allows an efficient and precise numerical study of effective velocities in fractured structures. We model the propagation of plane waves through a set of different, randomly cracked media. In these numerical experiments we vary the wavelength of the plane waves, the crack porosity and the crack density. The synthetic results are compared with several static theories that predict the effective P‐ and S‐wave velocities in fractured materials in the long wavelength limit. For randomly distributed and randomly orientated, rectilinear, non‐intersecting, thin, dry cracks, the numerical simulations of velocities of P‐, SV‐ and SH‐waves are in excellent agreement with the results of the modified (or differential) self‐consistent theory. On the other hand for intersecting cracks, the critical crack‐density (porosity) concept must be taken into account. To describe the wave velocities in media with intersecting cracks, we propose introducing the critical crack‐density concept into the modified self‐consistent theory. Numerical simulations show that this new formulation predicts effective elastic properties accurately for such a case. 相似文献
15.
Numerical simulations of full-wave fields and analysis of channel wave characteristics in 3-D coal mine roadway models 总被引：2，自引：0，他引：2
Currently, numerical simulations of seismic channel waves for the advance detection of geological structures in coal mine roadways focus mainly on modeling twodimensional wave fields and therefore cannot accurately simulate three-dimensional (3-D) full-wave fields or seismic records in a full-space observation system. In this study, we use the first-order velocity–stress staggered-grid finite difference algorithm to simulate 3-D full-wave fields with P-wave sources in front of coal mine roadways. We determine the three components of velocity Vx, Vy, and Vz for the same node in 3-D staggered-grid finite difference models by calculating the average value of Vy, and Vz of the nodes around the same node. We ascertain the wave patterns and their propagation characteristics in both symmetrical and asymmetric coal mine roadway models. Our simulation results indicate that the Rayleigh channel wave is stronger than the Love channel wave in front of the roadway face. The reflected Rayleigh waves from the roadway face are concentrated in the coal seam, release less energy to the roof and floor, and propagate for a longer distance. There are surface waves and refraction head waves around the roadway. In the seismic records, the Rayleigh wave energy is stronger than that of the Love channel wave along coal walls of the roadway, and the interference of the head waves and surface waves with the Rayleigh channel wave is weaker than with the Love channel wave. It is thus difficult to identify the Love channel wave in the seismic records. Increasing the depth of the receivers in the coal walls can effectively weaken the interference of surface waves with the Rayleigh channel wave, but cannot weaken the interference of surface waves with the Love channel wave. Our research results also suggest that the Love channel wave, which is often used to detect geological structures in coal mine stopes, is not suitable for detecting geological structures in front of coal mine roadways. Instead, the Rayleigh channel wave can be used for the advance detection of geological structures in coal mine roadways. 相似文献
16.
An upwind fast sweeping scheme for calculating seismic wave first‐arrival travel times for models with an irregular free surface 
下载免费PDF全文
下载免费PDF全文 The topography‐dependent eikonal equation formulated in a curvilinear coordinate system has recently been established and revealed as being effective in calculating first‐arrival travel times of seismic waves in an Earth model with an irregular free surface. The Lax–Friedrichs sweeping scheme, widely used in previous studies as for approximating the topography‐dependent eikonal equation viscosity solutions, is more dissipative and needs a much higher number of iterations to converge. Furthermore, the required number of iterations grows with the grid refinement and results in heavy computation in dense grids, which hampers the application of the Lax–Friedrichs sweeping scheme to seismic wave travel‐time calculation and high‐resolution imaging. In this paper, we introduce a new upwind fast sweeping solver by discretising the Legendre transform of the numerical Hamiltonian of the topography‐dependent eikonal equation using an explicit formula. The minimisation related to the Legendre transform in the sweeping scheme is solved analytically, which proved to be much more efficient than the Lax–Friedrichs algorithm in solving the topography‐dependent eikonal equation. Several numerical experiments demonstrate that the new upwind fast sweeping method converges and achieves much better accuracy after a finite number of iterations, independently of the mesh size, which makes it an efficient and robust tool for calculating travel times in the presence of a non‐flat free surface. 相似文献
17.
本文通过数值模拟研究了介质黏弹性对瑞雷波传播的影响.模拟采用结合了交错Adams-Bashforth时间积分法、应力镜像法和多轴完美匹配层的标准交错网格高阶有限差分方案.通过模拟结果和理论结果对比,测试了方法的精度,验证了结果的正确性.在均匀半空间模型中,分别从波场快照、波形曲线及频散能量图三个角度,对黏弹性介质瑞雷波衰减和频散特性进行了详细分析.两层速度递增模型被用于进一步分析瑞雷波在黏弹性层状介质中的特性.结果表明：由于介质的黏弹性,瑞雷波振幅发生衰减,高频成分比低频成分衰减更剧烈,衰减程度随偏移距增大而增强;瑞雷波相速度发生频散,且随频率增大而增大,频散能量的分辨率有所降低;黏弹性波动方程中的参考频率,不会影响瑞雷波振幅衰减和相速度频散的程度,但决定了黏弹性和弹性介质瑞雷波相速度相等的频率位置.本研究有助于人们更好地理解地球介质中瑞雷波的行为,并为瑞雷波勘探的应用和研究提供了科学和有价值的参考. 相似文献
18.
An optimized finite difference method based on a polar coordinate system for regional-scale irregular topography 下载免费PDF全文
下载免费PDF全文 The finite difference method (FDM) is an important numerical approach for simulating the propagation of seismic waves, and some FDMs can be used to study the impact of the Earth’s curvature and topography over large distances. To efficiently model the effects of the Earth’s irregular topography on the propagation of seismic waves, here we optimize a previously proposed grid mesh method and develop a novel two-dimensional boundary-conforming FDM based on a curvilinear polar coordinate system. This method efficiently simulates the propagation of seismic waves in an arc-shaped model with large variations in surface topography. Our method was benchmarked against other reported methods using several global-scale models. The consistency of the results confirms the validity of our proposed optimization strategy. Furthermore, our findings indicate that the proposed optimization strategy improves computational efficiency. 相似文献
19.
20.
Yonghai Zhang 《Geophysical Prospecting》2010,58(6):915-924
Seismic data acquired along rugged topographic surfaces present well‐known problems in seismic imaging. In conventional seismic data processing, datum statics are approximated by the surface consistence assumption, which states that all seismic rays travel vertically in the top layer. Hence, the datum static for each single trace is constant. In case this assumption does not apply, non‐constant statics are required. The common reflection surface (CRS) stack for rugged surface topography provides the capability to deal with this non‐vertical static issue. It handles the surface elevation as a coordinate component and treats the elevation variation in the sense of directional datuming. In this paper I apply the CRS stack method to a synthetic data set that simulates the acquisition along an irregular surface topography. After the CRS stack, by means of the wavefield attributes, a simple algorithm for redatuming the CRS stack section to an arbitrarily chosen planar surface is performed. The redatumed section simulates a stack section whose acquisition surface is the chosen planar surface. 相似文献