首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
Observations of pile foundation performance during previous earthquakes have shown that pile failure has been caused by lateral ground movements resulting from soil liquefaction. The recognition that lateral ground movements may play a critical role in pile performance during an earthquake has important implications for design and risk assessment, and requires that analytical models be devised to evaluate these potential problems.In this paper, parametric studies were conducted to estimate the maximum bending moments induced in piles subjected to lateral ground displacement. The results are summarized in charts using dimensionless parameters.The analyses reveal that the existence of a nonliquefiable layer at the ground surface can affect significantly the maximum bending moment of the pile. When a relatively thick nonliquefiable layer exists above a liquefiable layer, neither the material nonlinearity of the soil nor loss of soil stiffness within the liquefiable layer significantly affect the maximum bending moment. When the thickness of the liquefiable soils is greater than about three times that of an overlying intact layer, soil stiffness in the liquefiable layer must be chosen carefully when evaluating the maximum bending moment.  相似文献   

2.
可液化倾斜场地中桩基动力响应振动台试验研究   总被引:2,自引:1,他引:1       下载免费PDF全文
为研究倾斜场地中桩基的动力响应,以2011年新西兰地震中受损的Dallington桥为原型,设计并完成可液化倾斜场地桥梁桩-土相互作用的振动台模型试验。试验再现了喷砂、冒水、地裂缝、场地流滑等宏观现象。试验结果表明,土层足够的液化势及惯性是造成倾斜场地侧向流滑的必要条件;浅层土相比深层土更易液化,液化层中的加速度由下至上呈现逐渐衰减的趋势,而未液化砂土层却表现为逐渐增大的特征;深部测点的桩侧土压力明显大于浅部测点,且土体的液化会弱化土对结构的压力;结构应变最大值位于上部桥台,而结构弯矩在桩身中部及土层分界面附近出现两个较大值,桩端嵌固及倾斜场地流滑是造成出现两个弯矩较大值的主要原因。  相似文献   

3.
Soil liquefaction induced by earthquakes frequently cause costly damage to pile foundations. However, various aspects of the dynamic behavior and failure mechanisms of piles in liquefiable soils still remain unclear. This paper presents a shake-table experiment conducted to investigate the dynamic behavior of a reinforced-concrete (RC) elevated cap pile foundation during (and prior to) soil liquefaction. Particular attention was paid to the failure mechanism of the piles during a strong shaking event. The experimental results indicate that decreasing the frequency and increasing the amplitude of earthquake excitation increased the pile bending moment as well as the speed of the excess pore pressure buildup in the free-field. The critical pile failure mode in the conducted testing configuration was found to be of the bending type, which was also confirmed by a representative nonlinear numerical model of the RC pile. The experimental results of this study can be used to calibrate numerical models and provide insights on seismic pile analysis and design.  相似文献   

4.
<正>This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground.The soil profile,contained in a large-scale laminar shear box,consisted of a horizontally saturated sand layer overlaid with a silty clay layer,with the simulated low-cap pile groups embedded.The container was excited in three E1 Centra earthquake events of different levels.Test results indicate that excessive pore pressure(EPP) during slight shaking only slightly accumulated,and the accumulation mainly occurred during strong shaking.The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased.The acceleration response of the sand was remarkably influenced by soil liquefaction.As soil liquefaction occurred,the peak sand displacement gradually lagged behind the input acceleration;meanwhile,the sand displacement exhibited an increasing effect on the bending moment of the pile,and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top.A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events.It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun.  相似文献   

5.
The objectives of this paper are to show practically: (1) the validation of a proposed three-dimensional effective stress analysis for the pile foundations, and (2) the effectiveness of remedial deposits on pile stresses under liquefaction by making comparisons between the results of centrifuge tests and those of the proposed analysis. Two foundation models supported by end-bending piles were studied with improved and unimproved deposits. There exists a good consistency between the numerical and experimental results for excess pore water-pressure ratios ranging from 0 to about 0·9. From the numerical results, the bending moment at the pile top with the improved deposit is about 50 per cent lower than that with the unimproved deposit. However, it was found that the smaller the bending moment develops in the pile with the improved deposit, the larger the compressive and/or tensional axial stresses in the pile. This is due to the predominant excitation of rocking vibration of the foundation. From the analytical and experimental results, it has been found that the remedial method can be a variable means to protect piles from soil liquefaction hazards. However, both axial stress and bending moment produced in piles should be considered in assessing the liquefied seismic capacity of group pile-foundation–structural systems with improved soil deposits. © 1998 John Wiley & Sons, Ltd.  相似文献   

6.
To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction.  相似文献   

7.
An analytical fragility analysis was conducted in order to characterize the seismic vulnerability of existing southern Illinois wall pier supported highway bridges to potential earthquakes. To perform this fragility analysis, a detailed inventory survey was first taken of the wall pier bridges identified in an earlier random sampling of southern Illinois priority emergency route bridges. From the survey three types of wall pier bridges were identified. Of those identified, hammerhead and regular wall pier supported bridges represented nearly 90% of the population. Incorporating structural variations determined from the random sample survey, nearly 100 three‐dimensional nonlinear finite element models were constructed. Each model was subjected to a randomly assigned synthetic earthquake representative of those that could potentially occur within the region. From these analyses, a series of wall pier supported bridge fragility curves were produced. In addition, a liquefaction fragility analysis was conducted in order to characterize the seismic vulnerability of southern Illinois wall pier supported highway bridge sites to liquefaction in potential earthquakes. To perform this second fragility analysis, wall pier bridges within the southern Illinois random sample that may be susceptible to liquefaction were identified. A soil profile from each of these susceptible bridge sites was then subjected to randomly assigned bedrock motions, and an Arias intensity liquefaction analysis was carried out. From these analyses, a fragility curve for the potentially liquefiable wall pier supported bridge sites was produced. Overall results of this study indicate that southern Illinois wall pier supported bridges are moderately vulnerable to structural damage in a 2% probability of exceedance in 50 year earthquake, and in some cases they could also be highly vulnerable to on‐site liquefaction events. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

8.
Pile foundation as well as other underground structures could be seriously affected by soil liquefaction during strong earthquakes. Damages on pile foundation due to liquefaction can be reduced by implementation of some soil improvement method. Main objective of present study is developing of drain method that can improve the soil in order to mitigate the destructiveness of liquefaction on superstructure supported by pile foundation. Series of shaking table tests were conducted on 2×2 pile foundation and soil model was improved by drains. Configurations of drains around piles, intensity of shaking were one of the parameters that were changing during the tests in order to investigate the response of pile foundation in improved soil condition.Shaking table tests and performed On-site experiment showed the following effects of the new drain method. (1) When the intensity of earthquake motion is 200 gal or less, generation of excess pore water pressure is reduced and the pile bending moment is decreased, (2) when the intensity of earthquake motion is stronger (300 gal or more), drainage effect prevents disappearance of subgrade reaction, and (3) proposed new type of drain can control excess pore water pressure without clogging.  相似文献   

9.
为研究液化场地变截面桩的动力响应,依托翔安大桥实体工程,采用有限元软件,建立变截面桩-土和等截面桩-土相互作用模型,模拟液化场地变截面桩及等截面桩在地震作用下的振动反应,分析在地震作用下变截面位置不同的变截面桩及等截面桩的动力响应特征。结果表明:地震作用下,液化土层不同深度处的孔压比变化规律基本相同,均从0逐渐增大最后趋于稳定;变截面桩的桩身加速度和桩身位移均大于等截面桩,且桩顶加速度峰值出现的时刻均滞后于桩底;在饱和砂土层处,桩身位移变化趋势均较陡;变截面桩的桩身弯矩峰值和桩身剪力峰值均大于等截面桩,且其峰值出现的位置较等截面桩深;地震作用下,变截面桩及等截面桩的弯矩与剪力均在安全范围之内;液化场地变截面梁桥桩基础抗震设计时,应着重分析液化土层与非液化土层分界面以下的抗弯能力设计及液化土层中抗剪能力设计。  相似文献   

10.
基于黏弹性人工边界,建立上部结构-桩-土的共同作用三维有限元模型,分析地震作用下预应力混凝土管桩的运动响应特性。分别针对预应力混凝土管桩的桩径、双层软硬土剪切波速比值、上覆土层厚度、上部结构荷载等影响因素进行数值计算。参数分析表明:在地震作用下,桩径的增大会导致桩身整体弯矩相应增加,特别是桩身土层分界面处增大明显;软硬土层剪切波速比及上覆土层厚度的增加,引起土层分界面处桩身峰值弯矩增加;固定桩头条件下,桩头与桩身软硬土层分界面处均会产生较大的运动弯矩;上部结构的惯性荷载对固定桩头的内力有着较大影响,对桩身深处段弯矩影响较小。本文研究结论可为预应力混凝土管桩抗震设计提供有益的理论参考。  相似文献   

11.
For sites susceptible to liquefaction induced lateral spreading during a probable earthquake, geotechnical engineers often need to know the undrained residual shear strength of the liquefied soil deposit to estimate lateral spreading displacements, and the forces acting on the piles from the liquefied soils in order to perform post liquefaction stability analyses. The most commonly used methods to estimate the undrained residual shear strength (Sur) of liquefied sand deposits are based on the correlations determined from liquefaction induced flow failures with SPT and CPT data. In this study, 44 lateral spread case histories are analyzed and a new relationship based on only lateral spread case histories is recommended, which estimates the residual shear strength ratio of the liquefiable soil layer from normalized shear wave velocity. The new proposed method is also utilized to estimate the residual lateral displacement of an example bridge problem in an area susceptible to lateral spreading in order to provide insight into how the proposed relationship can be used in geotechnical engineering practice.  相似文献   

12.
This paper investigates the importance of bending–buckling interaction in seismic design of piles in liquefiable soils using numerical techniques. A pseudo-static analysis has been performed using a well documented case history, where the pile–soil interaction is modelled as a beam on nonlinear winkler foundation (BNWF). Six possible analytical methods, three force based and three displacement based, are performed in which the pile is subjected to both lateral and axial load. Three out of six analysis cases did not predict the failure of the piles when analysed only for bending (i.e., lateral loads only). The buckling analysis showed that the pile was also safe against pure buckling during full liquefaction. Further, two out of those three cases which did not predict failure in bending were reanalysed for bending–buckling interaction (i.e., lateral and axial loads acting simultaneously). These combined analyses showed a more realistic behaviour of pile response and did predict the pile failure. Hence, it can be concluded that if a pile is designed for bending and buckling criteria separately and safe for these individual design criteria, it may fail due to their combined effect.  相似文献   

13.
A case study is presented of the interaction between the bending due to laterally spreading forces and axial-load induced settlement on the piled foundations of the Kandla Port and Customs Tower located in Kandla Port, India, during the 2001 Bhuj earthquake. The 22 m tall tower had an eccentric mass at the roof and was supported on a piled-raft foundation that considerably tilted away as was observed in the aftermath of the earthquake. The soil at the site consists of 10 m of clay overlaid by a 12 m deep sandy soil layer. Post-earthquake investigation revealed the following: (a) liquefaction of the deep sandy soil strata below the clay layer; (b) settlement of the ground in the vicinity of the building; (c) lateral spreading of the nearby ground towards the sea front. The foundation of the tower consists of 0.5 m thick concrete mat and 32 piles. The piles are 18 m long and therefore passes through 10 m of clayey soil and rested on liquefiable soils. Conventional analysis of a single pile or a pile group, without considering the raft foundation would predict a severe tilting and/or settlement of the tower eventually leading to a complete collapse. It has been concluded that the foundation mat over the non-liquefied crust shared a considerable amount of load of the superstructure and resisted the complete collapse of the building.  相似文献   

14.
Numerical analysis of an infinite pile group in a liquefiable soil was considered in order to investigate the influence of pile spacing on excess pore pressure distribution and liquefaction potential. It was found that an optimal pile spacing exists resulting in minimal excess pore pressure. It was also found that certain pile group configurations might reduce liquefaction potential, compared to free field conditions. It was observed that for closely spaced piles and low frequency of loading, pile spacing has little influence on the response of the superstructure.  相似文献   

15.
对由碎石桩和CFG桩构成的多桩型复合地基的作用机理进行分析,通过数值模拟,对多桩型复合地基的动力特性进行研究,探讨桩型配比、桩径、桩长、CFG桩桩体刚度和碎石桩桩体渗透性等设计参数对多桩型复合地基动力特性的影响。研究结果表明:相同条件下地震期多桩型复合地基的动变形小于碎石桩复合地基而大于CFG桩复合地基,震后沉降量相对较小,在工程设计时碎石桩与CFG桩的桩型配比宜为4∶5;随桩体长度、桩体直径和CFG桩刚度的增加,多桩型复合地基地震期的竖向动变形逐渐减小;随碎石桩桩体渗透性的增加,多桩型复合地基中的超动孔隙水压力减小,震后沉降量降低。  相似文献   

16.
本文以一座三跨总长60 m的整体桥为案例桥,分别试设计了同跨径的半整体桥、延伸桥面板桥和常规连续梁桥。通过Midas/Civil软件建立四种桥型的有限元模型,并对其进行了E1和E2反应谱分析和时程分析,对比了四种桥型的结构反应峰值(墩顶位移、桥墩及桩基剪力与弯矩、台底位移、桥台桩基剪力与弯矩)。计算结果表明:当桥梁存在15°的斜交角,整体桥、半整体桥在地震动沿平行于桥台长边方向及其垂直方向输入时更不利,而延伸桥面板桥和常规连续梁桥在地震动沿顺桥向和横桥向输入时更不利。四种桥型在地震作用下:整体桥抗震性能最优异,但其台底位移、桥台桩基的剪力和弯矩最大;半整体桥台底位移、桥台桩基的剪力和弯矩最小,其墩顶位移、桥墩及桩基的剪力和弯矩仅比整体桥大;延伸桥面板桥和常规连续梁桥的墩-梁相对位移远大于整体桥和半整体桥,不适用于地震基本烈度高的区域。  相似文献   

17.
桩基础抗震性能的简易评价方法   总被引:1,自引:0,他引:1  
桩基础的抗震性能可从承载力和变形两方面来评价.承载力可考虑地震时作用于结构上的荷载组合,多采用拟静力法进行分析,不同因素变异的影响可用概率分析或可靠度方法予以考虑.变形分析多为按承载力设计之后的校核,其中地震力和土体参数以及地质条件等因素影响可分别加以评估.本文着重阐明基于一维波动方程和概率分析的桩基抗震性能实用分析方法,并以桥梁桩基础为例进行讨论,其中考虑的关键因素为设计地震加速度、测站记录、基桩尺寸及其配筋率.研究表明,当土层液化可忽略时最大弯矩会发生在桩顶,故增加桩顶延性可有效提升桩基础的抗震性能.  相似文献   

18.
The anti-slide support structure is widely used in the anti-seismic reinforcement of bridge foundations, but related experimental research was processing slowly. Based on the prototype of the Jiuzhaigou bridge at the Chengdu-Lanzhou Railway, a 3-D simulation model was established on the basis of the shaking table model test, and the rationality of the dynamic analysis model was verified by indicators such as the bending moment of the bridge piles, peak soil pressure, and PGA amplification factors. The results show that the inertia force of the bridge pier has an important influence on the deformation of the pile foundation. The bending moment and shearing force are larger in lateral bridge piles, and the maximum value is near the pile top. The PGA amplification factor is stronger in the back of the rear anti-slide piles and so is it in front of the bridge pier, and the soil is prone to slip and damage. The bedrock is rigid and the dynamic response is maintained at a low level. The anti-slide piles in the rear row play a major role in the anti-seismic reinforcement design, and the anti-slide piles in the front row can be used as an auxiliary support structure.  相似文献   

19.
A Study of Piles during Earthquakes: Issues of Design and Analysis   总被引:1,自引:0,他引:1  
The seismic response of pile foundations is a very complex process involving inertial interaction between structure and pile foundation, kinematic interaction between piles and soils, seismically induced pore-water pressures (PWP) and the non-linear response of soils to strong earthquake motions. In contrast, very simple pseudo-static methods are used in engineering practice to determine response parameters for design. These methods neglect several of the factors cited above that can strongly affect pile response. Also soil–pile interaction is modelled using either linear or non-linear springs in a Winkler computational model for pile response. The reliability of this constitutive model has been questioned. In the case of pile groups, the Winkler model for analysis of a single pile is adjusted in various ways by empirical factors to yield a computational model for group response. Can the results of such a simplified analysis be adequate for design in all situations?The lecture will present a critical evaluation of general engineering practice for estimating the response of pile foundations in liquefiable and non-liquefiable soils during earthquakes. The evaluation is part of a major research study on the seismic design of pile foundations sponsored by a Japanese construction company with interests in performance based design and the seismic response of piles in reclaimed land. The evaluation of practice is based on results from field tests, centrifuge tests on model piles and comprehensive non-linear dynamic analyses of pile foundations consisting of both single piles and pile groups. Studies of particular aspects of pile–soil interaction were made. Piles in layered liquefiable soils were analysed in detail as case histories show that these conditions increase the seismic demand on pile foundations. These studies demonstrate the importance of kinematic interaction, usually neglected in simple pseudo-static methods. Recent developments in designing piles to resist lateral spreading of the ground after liquefaction are presented. A comprehensive study of the evaluation of pile cap stiffness coefficients was undertaken and a reliable method of selecting the single value stiffnesses demanded by mainstream commercial structural software was developed. Some other important findings from the study are: the relative effects of inertial and kinematic interactions between foundation and soil on acceleration and displacement spectra of the super-structure; a method for estimating whether inertial interaction is likely to be important or not in a given situation and so when a structure may be treated as a fixed based structure for estimating inertial loads; the occurrence of large kinematic moments when a liquefied layer or naturally occurring soft layer is sandwiched between two hard layers; and the role of rotational stiffness in controlling pile head displacements, especially in liquefiable soils. The lecture concludes with some recommendations for practice that recognize that design, especially preliminary design, will always be based on simplified procedures.  相似文献   

20.
为了研究强震区桥梁跨活动断层时,桩基在地震中的动力响应,以海文大桥为工程背景,利用Midas GTS有限元软件建立其强震区桩-海床岩土体-断层耦合作用的数值模型,研究不同强度(0.20g~0.60g)的50年超越概率为10%的地震波(后文简称5010地震波)作用下,桥梁桩基加速度、位移、弯矩及剪力的动力时程响应特性。结果表明:上部大厚度松散土体对桩身加速度有放大及滤波作用,而基岩对桩身加速度几乎不产生作用;断层上、下盘桩基础的桩顶水平位移随输入地震动强度的增大而增大,但达到振幅的时刻一致;上、下盘桩基础桩顶竖向位移时程响应都在50 s以后产生永久沉降;桩身最大弯矩截面处时程响应均在40 s以后产生永久弯矩;应重点考虑上部覆盖层软硬土体界面和基岩界面的抗弯承载力设计,及桩顶和基岩面附近的抗剪承载力设计;上盘桩基础按桩身加速度、弯矩、桩顶水平位移等动参数控制设计,下盘桩基础按动剪应力控制设计。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号