共查询到20条相似文献，搜索用时 328 毫秒
1.
Experimental and numerical investigations into the bearing capacity of circular footing on geogrid-reinforced compacted granular fill layer overlying on natural clay deposit have been conducted in this study. A total of 8 field tests were carried out using circular model rigid footing with a diameter of 0.30 m. 3D numerical analyses were performed to simulate soil behavior using finite element program Plaxis 3D Foundation. The results from the FE analysis are in very good agreement with the experimental observations. It is shown that the degree of improvement depends on thickness of granular fill layer and properties and configuration of geogrid layers. Parameters of the experimental and numerical analyses include depth of first reinforcement, vertical spacing of reinforcement layers. The results indicate that the use of geogrid-reinforced granular fill layers over natural clay soils has considerable effects on the bearing capacity and significantly reduces the lateral displacement and vertical displacement of the footing. 相似文献
2.
By using the upper bound finite‐elements limit analysis, with an inclusion of single and two horizontal layers of reinforcements, the ultimate bearing capacity has been computed for a rigid strip footing placed over (i) fully granular, (ii) cohesive‐frictional, and (iii) fully cohesive soils. It is assumed that (i) the reinforcements are structurally strong so that no axial tension failure can occur, (ii) the reinforcement sheets have negligible resistance to bending, and (iii) the shear failure can take place between the reinforcement and soil mass. It is expected that the different approximations on which the analysis has been based would generally remain applicable for reinforcements in the form of geogrid sheets. A method has been proposed to incorporate the effect of the reinforcement in the analysis. The efficiency factors, ηc and ηγ, to be multiplied with Nc and Nγ , for finding the bearing capacity of reinforced foundations, have been established. The results have been obtained (i) for different values of ? in case of fully granular and cohesive‐frictional soils, and (ii) for different rates at which the cohesion increases with depth for a fully cohesive soil. The optimum positions of the reinforcements' layers have also been determined. The effect of the reinforcements' length on the results has also been analyzed. As compared to cohesive soils, the granular soils, especially with higher values of ?, cause a much greater increase in the bearing capacity. The results compare reasonably well with the available theoretical and experimental data from literature. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
3.
Design of shallow foundations relies on bearing capacity values calculated using procedures that are based in part on solutions obtained using the method of characteristics, which assumes a soil following an associated flow rule. In this paper, we use the finite element method to determine the vertical bearing capacity of strip and circular footings resting on a sand layer. Analyses were performed using an elastic–perfectly plastic Mohr–Coulomb constitutive model. To investigate the effect of dilatancy angle on the footing bearing capacity, two series of analyses were performed, one using an associated flow rule and one using a non-associated flow rule. The study focuses on the values of the bearing capacity factors Nq and Nγ and of the shape factors sq and sγ for circular footings. Relationships for these factors that are valid for realistic pairs of friction angle and dilatancy angle values are also proposed. 相似文献
4.
Kousik Deb 《国际地质力学数值与分析法杂志》2008,32(10):1267-1288
The present study pertains to the development of a mechanical model for predicting the behavior of granular bed‐stone column‐reinforced soft ground. The granular layer that has been placed over the stone column‐reinforced soft soil has been idealized by the Pasternak shear layer. The saturated soft soil has been idealized by the Kelvin–Voigt model to represent its time‐dependent behavior and the stone columns are idealized by stiffer Winkler springs. The nonlinear behavior of the granular fill has been incorporated in this study by assuming a hyperbolic variation of shear stress with shear strain as in one reported literature. Similarly, for soft soil it has also been assumed that load‐settlement variation is hyperbolic in nature. The effect of consolidation of the soft soil due to inclusion of the stone columns has also been included in the model. Plane‐strain conditions are considered for the loading and foundation soil system. The numerical solutions are obtained by a finite difference scheme and the results are presented in a non‐dimensional form. Parametric studies for a uniformly loaded strip footing have been carried out to show the effects of various parameters on the total as well as differential settlement and stress concentration ratio. It has been observed that the presence of granular bed on the top of the stone columns helps to transfer stress from soil to stone columns and reduces maximum as well as differential settlement. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
5.
The scaled boundary finite‐element method is derived for elastostatic problems involving an axisymmetric domain subjected to a general load, using a Fourier series to model the variation of displacement in the circumferential direction of the cylindrical co‐ordinate system. The method is particularly well suited to modelling unbounded problems, and the formulation allows a power‐law variation of Young's modulus with depth. The efficiency and accuracy of the method is demonstrated through a study showing the convergence of the computed solutions to analytical solutions for the vertical, horizontal, moment and torsion loading of a rigid circular footing on the surface of a homogeneous elastic half‐space. Computed solutions for the vertical and moment loading of a smooth rigid circular footing on a non‐homogeneous half‐space are compared to analytical ones, demonstrating the method's ability to accurately model a variation of Young's modulus with depth. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
6.
地基极限承载力分析是土力学研究中的一个经典课题。基于Hellinger-Reissner混合变分原理和有限元方法,将岩土体弹塑性问题构造成基于有限元框架的二阶锥规划（second-order cone programming,SOCP）问题,进而提出一种基于二阶锥规划理论的增量有限元法,即FEM-SOCP法。将岩土体弹塑性问题构造成二阶锥规划的数学优化问题,可以避免采用传统弹塑性计算中复杂的应力点积分等算法和屈服面棱角的平滑处理。此外,对于二阶锥规划问题,可以采用具有原始?对偶内点求解法的标准数学规划求解器MOSEK进行求解。将增量加载FEM-SOCP法应用于经典的基底粗糙的条形浅基础地基极限承载力分析中,分别考虑了关联和非关联塑性条件下的Mohr-Coulomb屈服准则。数值结果表明：所提出的增量加载FEM-SOCP法获得的地基承载力系数及地基承载力与传统FEM计算结果基本一致,而与常规有限元计算结果相比,基于增量加载的FEM-SOCP法所获得的屈服区更加平滑。 相似文献
7.
A practical and efficient approach of implementing second‐order reliability method (SORM) is presented and illustrated for cases related to foundation engineering involving explicit and implicit limit state functions. The proposed SORM procedure is based on an approximating paraboloid fitted to the limit state surface in the neighborhood of the design point and can be easily carried out in a spreadsheet. Complex mathematical operations are relegated to relatively simple user‐created functions. The failure probability is calculated automatically based on the reliability index and principal curvatures of the limit state surface using established closed‐form SORM formulas. Four common foundation engineering examples are analyzed using the proposed method and discussed: immediate settlement of a flexible rectangular foundation, bearing capacity of a shallow footing, axial capacity of a vertical single pile, and deflection of a pile under lateral load. Comparisons with Monte Carlo simulations are made. In the case of the laterally loaded pile, the friction angle of the soil is represented as a one‐dimensional random field, and pile deflections are computed based on finite element analysis on a stand‐alone computer package. The implicit limit state function is approximated via the response surface method using two quadratic models. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
8.
A novel three‐dimensional particle‐based technique utilizing the discrete element method is proposed to analyze the seismic response of soil‐foundation‐structure systems. The proposed approach is employed to investigate the response of a single‐degree‐of‐freedom structure on a square spread footing founded on a dry granular deposit. The soil is idealized as a collection of spherical particles using discrete element method. The spread footing is modeled as a rigid block composed of clumped particles, and its motion is described by the resultant forces and moments acting upon it. The structure is modeled as a column made of particles that are either clumped to idealize a rigid structure or bonded to simulate a flexible structure of prescribed stiffness. Analysis is done in a fully coupled scheme in time domain while taking into account the effects of soil nonlinear behavior, the possible separation between foundation base and soil caused by rocking, the possible sliding of the footing, and the dynamic soil‐foundation interaction as well as the dynamic characteristics of the superstructure. High fidelity computational simulations comprising about half a million particles were conducted to examine the ability of the proposed technique to model the response of soil‐foundation‐structure systems. The computational approach is able to capture essential dynamic response patterns. The cyclic moment–rotation relationships at the base center point of the footing showed degradation of rotational stiffness by increasing the level of strain. Permanent deformations under the foundation continued to accumulate with the increase in number of loading cycles. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
9.
In this paper, an effort is made to evaluate the seismic bearing capacity of shallow strip footing resting on c–ф soil. The formulation is developed to get a single coefficient of bearing capacity for simultaneous resistance of weight, surcharge and cohesion. Limit equilibrium method in Pseudo-static approach with Coulomb mechanism is applied here to evaluate the seismic bearing capacity. The seismic bearing capacity of footing (quE) is expressed in terms of single coefficient NγE. The effect of various parameters viz. angle of internal friction of soil (ф), angle of wall friction (δ), cohesion (c), ratio of depth to width of footing (df/B0), seismic acceleration (kh, kv) are studied on the variation of seismic bearing capacity co-efficients. 相似文献
10.
《Geomechanics and Geoengineering》2013,8(2):107-111
The stability of eccentrically loaded strip footings on slopes was investigated using the method of finite element analysis based on the theory of elasto-plasticity. The analysis was done for two different soils involving three levels of slope angle, six footing locations, and two levels of load eccentricity plus central vertical loading. The strip footing analysed was a 3-ft (0.9 m) wide reinforced concrete footing embedded to a depth of 3 ft (0.9 m). The analysis focused on footing settlement, plastic yielding of soil, and ultimate bearing capacity. The results of analysis show that the influence of load eccentricity on footing pressure vs. footing centre settlement is negligibly small. However, the progressive soil yielding and ultimate bearing capacity are greatly affected by load eccentricity. Furthermore, the effect of load eccentricity differs considerably with the load location relative to the footing centre and slope crest. The ultimate bearing capacity for the eccentric load located on the slope side is significantly greater than that for the load located on the other side of the footing centre. For a 2(H): 1(V) slope in silty clay, the effect of slope on footing stability decreases with increasing footing location from slope crest as would be expected, and diminishes when the footing is located from the crest at about 5-times the footing width. 相似文献
11.
This letter is concerned with the undrained bearing capacity of rectangular footings with various aspect ratios and embedment ratios in uniform clay. It covers thin plate foundations with low aspect ratios and high embedment depth with embedment ratio up to 150. The work is based on small strain finite element analysis (FEA). After verification of the FEA model against existing solutions of the bearing capacity factors of rectangular footings, a series of FEA results are obtained. Based on the FEA results, a simple formulation is proposed to calculate the bearing capacity factor for rectangle footing with different aspect ratio in any embedment depth, extending the existing solutions to cover a wider ranges of footing aspect ratios and embedment ratios. 相似文献
12.
In the present study, the effects of multiple-footing configurations in sand on bearing capacity were investigated using field plate load tests and finite element analyses. Both strip and spread footings were considered in the finite element analyses. In each case, different footing distances were applied for the purposes of comparison among all of the results. From these results, it was observed that the load responses of multiple footings are similar to those of the single footing at distances greater than three times the footing width. Design equation and correlation parameters, necessary for quantifying the values of the bearing capacity ratio for the different multiple-footing configuration, were derived. Experimental test results from the literature were selected and used in verifying the proposed method. 相似文献
13.
《Geomechanics and Geoengineering》2013,8(4):235-251
The bearing capacity of footing has been studied by both conventional and numerical methods by many researchers. However, degradation of the microstructure of material, that is, a change in the microstructure of the soil, has not been adequately taken into account. Degradation of microstructure causes strain softening of materials and it leads to strain localization such as shear bands and slip bands. From an engineering point of view the strain localization is crucial because it is a precursor of failure. In the present study, finite element analyses of the bearing capacity of a shallow foundation on homogeneous and inhomogeneous saturated clay strata have been conducted using an elasto-viscoplastic soil constitutive model of microstructure change. A series of analyses of footing on clay deposit with different microstructure parameters have been carried out. Numerical results show that strain localization can be predicted during the loading of rigid footing on highly structured soil and strain localization affects the footing–soil interaction. The effects of footing roughness on the failure mechanism are also discussed in the study. 相似文献
14.
Many geotechnical problems involve undrained behavior of clay and the capacity in undrained loading. Most constitutive models used today are effective stress based and only indirectly obtain values for the undrained shear strength. To match the design profiles of undrained shear strengths, in active (A), direct simple shear (D) and passive (P) modes of loading are complicated. This paper presents the elastoplastic constitutive model NGI‐ADP which is based on the undrained shear strength approach with direct input of shear strengths. Consequently, exact match with design undrained shear strengths profiles is obtained and the well‐known anisotropy of undrained shear strength and stiffness is accounted for in the constitutive model. A non‐linear stress path‐dependent hardening relationship is used, defined from direct input of failure strains in the three directions of shearing represented by triaxial compression, direct simple shear and triaxial extension. With its clear input parameters the model has significant advantages for design analysis of undrained problems. The constitutive model is implemented, into finite element codes, with an implicit integration scheme. Its performance is demonstrated by a finite element analysis of a bearing capacity problem. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
15.
Maher Omar Khaled Hamad Mey Al Suwaidi Abdallah Shanableh 《Arabian Journal of Geosciences》2018,11(16):464
This research proposes the use of artificial neural network to predict the allowable bearing capacity and elastic settlement of shallow foundation on granular soils in Sharjah, United Arab Emirates. Data obtained from existing soil reports of 600 boreholes were used to train and validate the model. Three parameters (footing width, effective unit weight, and SPT blow count) are considered to have the most significant impact on the magnitude of allowable bearing capacity and elastic settlement of shallow foundations, and thus were used as the model inputs. Throughout the study, depth of footing was limited to 1.5 m below existing ground level and water table depth taken at the level of the footing. Performance comparison of the developed models (in terms of coefficient of determination, root mean square error, and mean absolute error) revealed that the developed artificial neural network models could be effectively used for predicting the allowable bearing capacity and elastic settlement. As such, the developed models can be used at the preliminary stage of estimating the allowable bearing capacity and settlements of shallow foundations on granular soils, instead of the conventional methods. 相似文献
16.
A micro‐hydromechanical model for granular materials is presented. It combines the discrete element method for the modeling of the solid phase and a pore‐scale finite volume formulation for the flow of an incompressible pore fluid. The coupling equations are derived and contrasted against the equations of conventional poroelasticity. An analogy is found between the discrete element method pore‐scale finite volume coupling and Biot's theory in the limit case of incompressible phases. The simulation of an oedometer test validates the coupling scheme and demonstrates the ability of the model to capture strong poromechanical effects. A detailed analysis of microscale strain and stress confirms the analogy with poroelasticity. An immersed deposition problem is finally simulated and shows the potential of the method to handle phase transitions. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
17.
《Geomechanics and Geoengineering》2013,8(3):185-194
In this paper, a model for the analysis of footings having finite flexural rigidity resting on a granular bed on top of stone columns improved saturated soft (clayey) soil has been proposed. Soft soil has been modeled as a Kelvin–Voigt body to represent its time dependent behavior. Pasternak shear layer has been used to represent the granular layer and the stone columns have been idealized by means of nonlinear Winkler springs. Nonlinear behavior of granular fill, soft soil and stone columns has been invoked by means of hyperbolic constitutive relationships. Governing differential equations for the soil–foundation system have been obtained and finite difference method has been adopted for solving these, using the Gauss-elimination iterative scheme. Detailed parametric study for a combined footing has been carried out to study the influence of parameters, like magnitude of applied load, flexural rigidity of footing, diameter of stone column, spacing of stone column, ultimate bearing capacity of granular fill, poor foundation soil and stone column, relative stiffness of stone columns and degree of consolidation, on flexural response of the footing. 相似文献
18.
Reliability analysis of bearing capacity of a strip footing at the crest of a simple slope with cohesive soil was carried out using the random finite element method (RFEM). Analyses showed that the coefficient of variation and the spatial correlation length of soil cohesion can have a large influence on footing bearing capacity, particularly for slopes with large height to footing width ratios. The paper demonstrates cases where a footing satisfies a deterministic design factor of safety of 3 but the probability of design failure is unacceptably high. Isotropic and anisotropic spatial variability of the soil strength was also considered. 相似文献
19.
The bearing capacity of shallow foundations in a non-homogeneous soil profile has been a challenging task in geotechnical
engineering. In this paper, a limit equilibrium method is used for calculating bearing capacity factors of shallow foundations
constructed on a two-layered granular soil profile. The main objective has been to determine the ultimate bearing capacity
computed from equivalent bearing capacity factors Nq and Nγ and comparing that with numerical analysis using finite element methods. It will be shown that the data obtained form the
developed method are well comparable with those obtained from FE approach, specially when the difference between shear strength
parameters of layers is low which is a practical case for sedimentary soil profiles and also for artificially compacted soils.
A computer program has been developed to investigate the influence of various parameters on bearing capacity factors. 相似文献
20.
《Geomechanics and Geoengineering》2013,8(2):139-150
The influence of a non-coaxial model for granular soils on shallow foundation analyses is investigated. The non-coaxial plasticity theory proposed by Rudnicki and Rice (J. Mech. Phys. Solids 1975, 23, 371–394) is integrated into a Drucker–Prager model with both perfect plasticity and strain hardening. This non-coaxial model is numerically implemented into the finite-element program ABAQUS using a substepping scheme with automatic error control. The influence of the non-coaxial model on footing settlement and bearing capacity is investigated under various loading and boundary conditions. Compared with the predictions using conventional coaxial models, the non-coaxial prediction results indicate that the settlement of a footing increases significantly when the non-coaxial component of plastic strain rate is taken into consideration, although ultimate footing bearing capacities are not affected significantly. The non-coaxial model has a different effect on footing settlements under different loading and boundary conditions. In general, the discrepancies between coaxial and non-coaxial predictions increase with increasing rotation of principal stresses of the soil mass beneath a footing. It can be concluded that if the non-coaxial component of plastic strain rate is neglected in shallow foundation problems using the finite-element method, the results tend to be non-conservative when designs are dominated by settlement of footings. 相似文献