共查询到20条相似文献，搜索用时 20 毫秒
1.
The excess pore water pressure distribution (u) induced by the penetration of a piezocone into clay and its dissipation behaviour have been investigated by laboratory model tests, theoretical analysis and numerical simulation. Based on the results of the tests and the analysis, a semi-theoretical method has been proposed to predict the piezocone penetration-induced pore pressure distribution in the radial direction from the shoulder of the cone. The method can consider the effect of the undrained shear strength (su), over-consolidation ratio (OCR) and rigidity index (Ir) of the soil. With a reliably predicted initial distribution of u and the measured curve of dissipation of pore water pressure at the shoulder of the cone (u2), the coefficient of consolidation of the soil in the horizontal direction (ch) can be back-fitted by analysis of the pore pressure dissipation. Comparing the back-fitted values of ch with the values directly estimated by a previously proposed method indicates that the previously proposed method can be used reliably to estimate ch values from non-standard dissipation curves (where u2 increases initially and then dissipates with time). 相似文献
2.
A cavity expansion–based solution is proposed in this paper for the interpretation of CPTu data under a partially drained condition. Variations of the normalized cone tip resistance, cone factor, and undrained-drained resistance ratio are examined with different initial specific volume and overconsolidation ratio, based on the exact solutions of both undrained and drained cavity expansion in CASM, which is a unified state parameter model for clay and sand. A drainage index is proposed to represent the partially drained condition, and the critical state after expansion and stress paths of cavity expansion are therefore predicted by estimating a virtual plastic region and assuming a drainage-index–based mapping technique. The stress paths and distributions of stresses and specific volume are investigated for different values of drainage index, which are also related to the penetration velocity with comparisons of experimental data and numerical results. The subsequent consolidation after penetration is thus predicted with the assumption of constant deviatoric stress during dissipation of the excess pore pressure. Both spherical and cylindrical consolidations are compared for dissipation around the cone tip and the probe shaft, respectively. The effects of overconsolidation ratio on the stress paths and the distributions of excess pore pressure and specific volume are then thoroughly investigated. The proposed solution and the findings would contribute to the interpretation of CPTu tests under a random drained condition, as well as the analysis of pile installation and the subsequent consolidation. 相似文献
3.
假设桩周土体为饱和黏弹性介质,采用Burgers流变模型进行描述,同时考虑竖向和径向固结,建立了固结控制方程。根据不排水和自由排水情况,将边界条件分为3类并分别得到超孔隙水压力消散的级数解答,该解答能够为孔压静力触探反求固结系数提供一定的理论依据。在此基础上编制了应用程序,对Burgers流变模型中主要参数进行了分析。结果表明,地基表面自由排水、桩端地基不排水条件下,在一定深度以内的桩周土体的固结速度随深度降低,但超过某一范围后固结速度趋于稳定;上、下边界均自由排水条件下,固结速度随深度增加呈现下降、稳定、升高;上、下边界均不排水条件时,孔压消散速度不随深度变化,可简化为本解答仅考虑径向固结的特例。同时土体的流变特性对超孔隙水压力消散的影响比较显著,流变参数G1/1的变化使超孔隙水压力趋于某不为0的定值,且该值随G1/1比值的增大而增加;其他参数不变时,土体剪切刚度比G1/G2的增大会引起孔压消散速度的下降。 相似文献
4.
The piezocone penetration test (CPTU) is commonly used as a fast and economical tool to identify soil profile and to estimate relevant material properties in soils ranging from fine to coarse-grained. Moreover, in the case of fine-grained soils (clays and silts), the consolidation coefficient and the permeability can be estimated through the dissipation test. Undrained conditions are commonly assumed for the interpretation of CPTU in fine-grained soils, but in soils such as silts, penetration may occur in partially drained conditions. This aspect is often neglected in data interpretation thus leading to an inaccurate estimate of soil properties. This paper investigates numerically the effect of partial drainage during penetration on the measured tip resistance and the subsequent pore pressure dissipation response contributing to a more accurate interpretation of field data. A realistic simulation of the cone penetration is achieved with the two-phase Material Point Method, modelling the soil response with the modified Cam-Clay model. The approach takes into account large soil deformations induced by the advancing cone, soil–water, and soil–structure interactions, as well as nonlinear soil behavior. 相似文献
5.
本文介绍了对以饱和粘性土为介质的模型槽中所进行的孔压静力触探(CPTU)试验,通过对试验数据的分析,得出探头贯入时周围土体的轴向附加应力和径向附加应力的变化及分布,锥尖、侧壁摩阻力以及超孔隙水压力的变化,以及停止贯入后孔压消散过程中探头周围土体的超孔压变化,从这些方面来探讨土中应力场的变化,附加应力的影响范围,临界深度现象以及超孔隙水压力的变化规律。 相似文献
6.
7.
为了探究静压沉桩与CPTU贯入力学机制,开展了饱和黏土中静压沉桩及CPTU贯入的离心模型试验,获得了静压沉桩与CPTU贯入过程中土压力、超孔压和贯入阻力的变化规律。同时,将静压桩和CPTU压入过程视为一系列球孔的连续贯入,应用圆孔扩张解答,建立了静压沉桩和CPTU贯入过程中锥头阻力、侧阻力与超孔压的预测方法。通过离心模型试验和理论预测结果的对比分析表明：随着桩体的压入,桩周土体的超孔压和土压力均逐渐增大,当桩头通过监测点时,超孔压与土压力均达到最大值;在饱和黏土中,CPTU锥头阻力、锥侧摩阻力和锥头超孔压与锥头贯入深度总体上呈线性关系。预测方法估算沉桩和CPTU贯入引起的土压力、超孔压与模型试验结果相符,较好地反映了饱和黏土中静压沉桩和CPTU贯入的力学机制。 相似文献
8.
汪发武 《吉林大学学报(地球科学版)》2001,31(1):64-69
通过排水剪切试验，揭示出易于产生粒子破碎的土体易于产生体积变化，土体初始结构和粒子破碎难易度对体积变化各阶段的影响。在与之相对应的不排水试验中，产生粒子破碎的土体最终产生了较高的超孔隙水压力，而且孔隙水压力产生的各阶段与排水试验中的体积变化阶段具有良好的对应关系。揭示了不同诱因产生的高速滑坡的共同特征，即在长距离运动中，由于粒子破碎的影响，滑动面土体在不排水条件下，抗剪强度因超孔隙水压力上升而下降，最终导致高速滑坡。同时，由于粒子破碎将导致土体自身渗透系数降低，土粒子破碎因而具有促进超孔隙水压力产生和减缓超孔隙水压力消散的双重效果。 相似文献
9.
The evaluation of the undrained cyclic resistance of sandy deposits is required to forecast the soil behaviour during an earthquake (liquefaction, cyclic mobility); due to the difficulties in obtaining undisturbed samples of most liquefiable soils, it is usually deduced from field test results such as cone penetration tests. This paper proposes a methodology to evaluate the undrained cyclic resistance from normalised cone resistance of two well-studied silica sands (Ticino and Toyoura), with different mineralogy, one mainly composed of feldspar, the other of quartz. The determination of the cyclic resistance of Ticino and Toyoura sands was achieved through undrained cyclic triaxial tests on reconstituted specimens. The tip resistance was deduced from CPTs performed in centrifuge with a miniaturised piezocone on homogeneous reconstituted models. Both the undrained cyclic and tip resistances were correlated with the state parameter ψ. Results of centrifuge and triaxial tests were combined through ψ to deduce the cyclic resistance ratio CRR directly from the normalised cone resistance. The shape of the curve relating CRR to the normalised cone resistance resulted unusual respect to all the recognised curves widespread in the geotechnical literature. The aim of the proposed correlations is to provide a useful instrument to improve the actual knowledge on liquefaction and to give a contribution based on the critical state soil mechanics framework to the development of refined correlations between the cyclic resistance of a sand and the results of cone penetration tests. 相似文献
10.
原位测试技术分析软土的应力历史可以避免取样及室内土工试验对土样的扰动,其结果能真实地反映现场土体的工程特性。以往基于孔压静力触探（CPTU）测试技术的超固结比（OCR）计算方法主要是针对超固结土取得的,缺乏对现场处于欠固结状态土体的考虑,具有一定的局限性。在已有研究成果的基础上,提出采用不完全孔压消散曲线的末段及时间平方根倒数外推法计算原位初始孔压,如果初始孔压大于静水压力,表明原位土层中存在固有孔压,为欠固结土。在此基础上,通过计算固结状态参数,可进一步对软土层的欠固结程度进行定量评价。工程应用表明,该方法不受软土性质和地域限制,具有普遍适用性,是合理可行的。在缺乏室内固结试验成果的情况下,可高效快捷地判别软土层的固结状态。研究成果对合理评价欠固结软土的工程特性具有一定的指导意义。 相似文献
11.
Tests on specimens of reconstituted illitic clay have examined the influence of temperature on the mechanical behaviour of clay soils. The program involved consolidation to effective confining pressures up to 1.5 MPa, heating to 100°C, and tests on normally consolidated and overconsolidated specimens with OCR = 2. The tests included isotropic consolidation, undrained triaxial compression with pore water pressure measurement, drained tests along controlled stress paths to investigate yielding behaviour, and undrained tests which involved heating and measurement of the resulting induced pore water pressures. The large strain strength envelope is independent of temperature. However, peak undrained strengths increase with temperature because smaller pore water pressures are generated during shearing. An important contribution from the study is a series of results for the yielding of illitic clay at three different temperatures. For the first time, there is clear evidence of yield loci decreasing in size with increasing temperature. An associated flow rule can be assumed without serious error. The results contribute to the confirmation of a thermal elastic-plastic soil model developed by the authors from cam clay following the addition of a small number of extra assumptions. Depending on the initial stress state, heating under undrained conditions may produce shear failure. 相似文献
12.
Application of an optimum design technique for determining the coefficient of consolidation by using piezocone test data 总被引：4，自引：0，他引：4
For normally consolidated clay, several researchers have developed a number of theoretical time factors to determine the coefficient of consolidation from piezocone test results. However, depending on assumptions and analytical techniques, it could vary considerably, even for a specific degree of consolidation. In this paper a method is proposed to determine a consistent coefficient of consolidation by applying the concept of an optimum design technique over all ranges of the degree of consolidation. Initial excess pore pressure distribution is assumed to be capable of being obtained by the successive spherical cavity expansion theory. The dissipation of pore pressure is simulated by means of a two-dimensional linear-uncoupled axi-symmetric consolidation analysis. The minimization of differences between measured and predicted excess pore pressure was carried out by the BFGS unconstrained optimum design algorithm with a one-dimensional golden section search technique. By analyzing numerical examples and in-situ test results, it was found that the adopted optimum design technique gives consistent and convergent results. 相似文献
13.
Prediction of long-term pore pressure dissipation behavior by short-term piezocone dissipation test 总被引：1，自引：0，他引：1
The coefficient of consolidation determined from piezocone dissipation test and common interpretation methods makes the predicted dissipation curve match only at 50% degree of dissipation of the measured dissipation curve. It makes it difficult to predict the long-term pore pressure dissipation behavior of in-situ soft deposits. Therefore, based on the authors' previous result [Kim YS, Lee SR, Kim YT. Application of an optimization design technique for determining the coefficient of consolidation by using piezocone test data. Computers and Geotechnics 1997;21(4): 77–93] in which an optimized coefficient of consolidation reflects well the measured dissipation trend over the input degree of dissipation range, a systematic way of predicting a more realistic pore pressure dissipation behavior at high degree of dissipation with the optimized coefficient of consolidation is proposed. It was found that, relatively over the wide range of dissipation, the optimized coefficient of consolidation is more consistent than those determined by other researchers' methods. Applied to some real examples, it is also shown that the dissipation behavior of pore water pressure at a high degree of the dissipation range can be predicted well if the coefficient of consolidation is determined using the optimization technique with the data up to around 50% dissipation. Thus, it is expected that the proposed method saves time and expenses in conducting dissipation tests in the field. 相似文献
14.
15.
Bryan A. McCabe Brian G. Sexton Barry M. Lehane 《Geotechnical and Geological Engineering》2013,31(1):183-197
Although finite element packages facilitating coupled consolidation analyses are increasingly in use, many practitioners still favour linear uncoupled analysis out of familiarity with the use of coefficients of consolidation. However, coefficients of consolidation measured by any single means tend to exhibit significant variation, with mean results from different laboratory and field tests also varying widely, leaving uncertainty over the correct values to apply to field problems. In this paper, a finite difference approach is used to back-calculate operational coefficients of consolidation from pore pressure measurements pertinent to a pile group driven in clay–silt. The research shows that this method is capable of successfully capturing the process of pore pressure dissipation, and that the operational coefficient of consolidation around the pile group is higher than that derived from piezocone dissipation tests in the same material. 相似文献
16.
通过等压固结静、动三轴试验,研究了渤海湾粉质黏土在循环荷载作用下的动力性质和循环荷载后不排水静力性质。试验结果表明,循环应力幅值比越大,平均轴向应变和轴向应变幅值越大;循环应力幅值比达到0.4时,平均轴向应变和轴向应变幅值随着循环周数增加迅速增大;循环应力幅值比相同,固结应力越大,轴向应变幅值越大,而平均轴向应变越小。在较大的循环应力幅值比下,平均孔压比值和孔压幅值比值随着循环周数的增大会达到稳定;循环应力幅值比越大平均孔压比值和孔压幅值比值均越大;相同循环应力幅值,固结应力越大平均孔压比值越小,而固结应力对孔压幅值比值影响较小。循环荷载的作用会导致循环荷载后不排水剪在q-p’平面上有效应力路径和孔压发展表现出超固结土的性质。 相似文献
17.
低能量强夯法加固粉质黏土地基试验研究 总被引：5，自引：1，他引：4
结合上海某铁路集装箱中心站地基处理工程,针对其场区上部粉质黏土、下部砂质粉土的地基条件,对低能量强夯法加固此类地基的适用性进行了现场试验研究。通过对夯击过程中超静孔隙水压力随夯击次数、深度、距离的变化规律及在不同性质土层中的增长与消散规律的研究,提出了运用试验手段确定强夯夯击次数、夯点间距、有效加固深度及两遍强夯间隔时间等施工参数的方法。同时,用静力触探试验和标准贯入试验对地基加固的效果进行了检验,结果说明低能量强夯法加固粉质黏土地基的适用性,从而进一步拓宽了低能量强夯法的应用范围。 相似文献
18.
19.
近年来许多研究者致力于通过孔压静力触探(CPTU)确定土体的渗透系数,但是存在偏差大,而且不能从机制上清楚地解释孔压静力触探确定土体渗透系数的原因。为了应用孔压静力触探现场快速地确定土体的渗透系数,在总结前人对孔压静力触探确定土体渗透系数方法的研究基础上,提出孔压静力触探时锥头处呈球冠形孔隙水流动的计算模型,假定锥头处初始超孔隙水压力为负指数型分布,推导出土体渗透系数的表达式,并且结合现场实测数据,将所提出的方法与已有的方法进行对比分析。研究发现：所提出的方法扩大了现有方法的应用范围;渗透系数计算结果受锥头角度的影响较大,随着锥头角度的增大而增大;针对国际上通用的60°角的标准锥头,所提出的方法计算的渗透系数大于前人的方法,而且更接近室内外试验结果。 相似文献
20.
The excess pore pressure generated by pile installation gradually dissipates following installation, which mainly dominates the increase of pile capacity with time. The dissipation of the excess pore pressure following pile installation has been widely investigated by experimental and theoretical studies. However, in most research, the consolidation coefficients were assumed to be constant for simplification, which may lead to errors. In the present study, the dissipation of the excess pore pressure is analyzed by radial consolidation theory with a variable consolidation coefficient based on the linear responses of e − ln(p′) and e − log(k). The governing equation of the radial consolidation considering variable compressibility and permeability are solved by the variable separation method. Bessel functions are used to solve the differential functions for the time independent part. The excess pore pressure immediately after pile installation is obtained from cavity expansion theory and is used as the initial condition of the consolidation process. Moreover, the influences of variable compressibility and permeability on the variation of consolidation coefficient and excess pore pressure dissipation are analyzed. 相似文献