共查询到20条相似文献，搜索用时 46 毫秒
1.
An analytical model to simulate the penetration of the piezocone penetrometer in cohesive soils is presented here. The elasto-plastic coupled field equations of the saturated cohesive soils (given by Voyiadjis and Abu-Farsakh) is used in this analysis. The numerical simulation of the piezocone penetration is implemented into a finite element program. The analytical model is used to analyze the miniature piezocone penetration tests (PCPT) conducted at LSU calibration chambers. Simulation of the piezocone penetration is done for two cases. In the first case, the soil–penetrometer interface friction is neglected, while in the second case, the soil–penetrometer interface friction is taken into consideration. The constraint approach is used to model the soil–piezocone interface friction in which the Mohr–Coulomb frictional model is used to define the sliding potential. Analysis is done for three different soil specimens with different stress histories. The results of the numerical simulations are compared with the experimental measurements of the miniature piezocone penetration tests (PCPT) in cohesive soil specimens conducted in LSU calibration chambers. The resulting excess pore pressure distribution and its dissipation using the numerical model are compared with some available prediction methods. © 1998 John Wiley & Sons, Ltd. 相似文献
2.
采用离散元商业软件PFC2D对7种重力场下静力触探试验进行了对比分析试验,以研究高、低重力场下静力触探试验的异同点。数值试验结果表明：不同重力场下土体受静力触探贯入主要影响区域不同,低重力场下主要是上部土体受到影响,高重力场下主要是下部土体受到影响;归一化贯入阻力的最大值和稳定值、归一化球应力和偏应力的最大值均与重力加速度的倒数呈线性关系,均随重力加速度倒数的增加而增大;土体经历了明显的加载、卸载过程,重力加速度越小,加载、卸载现象越明显,同一重力加速度下上部土体加载、卸载程度大于下部土体。 相似文献
3.
为研究结构性砂土静力触探的宏微观力学特性,在10 g重力场中生成一个净砂地基;将一个考虑胶结厚度的微观胶结接触模型引入到净砂地基中以生成结构性砂土地基;用一定速率移动探杆以模拟结构性砂土中的静力触探过程,其中,探杆由4面刚性墙组成。结果表明,随着贯入深度的增加,锥尖贯入阻力逐渐增大,增长速度逐渐减慢,在达到临界深度后贯入阻力在某一定值附近波动;锥尖部位有明显的力链集中现象,力链的集中程度和范围会随着贯入深度的增加而逐渐提高和扩大;静力触探过程中,探杆两侧的土体经历了明显的加载和卸载过程,且土体主应力方向发生偏转;离探杆越远,主应力偏转速度越慢,最终偏转角越小;不同深度处平均纯转动率（APR）的变化趋势基本相同,而APR最大值会随着土体深度而逐渐增加;探杆的贯入会使土颗粒间胶结发生破坏,胶结的破坏形式主要有拉剪破坏和压剪破坏两种,而拉剪破坏数目要比压剪破坏数目多。 相似文献
4.
Dynamic penetrometers have been used for offshore oil and gas industry applications such as pipeline feasibility studies and anchoring systems, and military applications including naval mine countermeasures and terminal ballistic studies. The main challenge of using dynamic penetrometers is the interpretation of their test results in order to deduce the mechanical properties of the penetrated soil via empirical or theoretical relations. Recently, a robust numerical method based on the Arbitrary Lagrangian–Eulerian (ALE) technique has been developed for analysing dynamic penetration problems and used to investigate a smooth penetrometer free falling into a uniform layer of clayey soil. Numerical as well as experimental results indicate that the penetration characteristics, including the impact energy, total time, and total depth of penetration, depend on the mechanical properties of the soil including its stiffness and strength parameters as well as the geometry of the penetrometer and its initial impact energy. In this study, the ALE method is employed to study the effect of shear strength increasing with depth (a common condition of seabed deposits) on the penetration characteristics of a free falling penetrometer. Conducting more than two thousand numerical simulations has shown that there is an approximate quadratic relation between the final embedment depth of a FFP penetrating into a non-uniform clay soil and the combined kinetic energy on contact with the soil and subsequent loss in potential energy of the penetrometer. 相似文献
5.
Field tests are widely used for soil characterization in geotechnical applications in spite of implementation difficulties. The light penetrometer is a well-known testing tool for fine soils, but the physical interpretation of the output data in the case of coarse granular materials is far less evident. Indeed, the data are considerably more sensitive in this case to various parameters such as fabric structure, particle shapes or the applied impact energy. In order to achieve a better understanding of the penetration process into a coarse granular material, a numerical study was performed by means of contact dynamics simulations. The penetration of a moving tip in a sample composed of irregular grain shapes was studied and the influence of the driving velocity and input energy on the penetration strength was analyzed. The results show that the latter grows with both the penetration rate and energy, despite the strong fluctuations occur due to a jamming–unjamming process in which the contact network connectivity evolves intermittently in correlation with the penetration strength. This analysis suggests that the time-averaged data provided by a penetrometer is reliable information from which the bulk strength properties of coarse granular materials can be evaluated. 相似文献
6.
《Geomechanics and Geoengineering》2013,8(2):137-146
This paper describes a numerical model developed to simulate the wave propagation in an elastic media that is applied to in situ dynamic penetration test devices currently used for site characterization. In the model, dynamic equilibrium equations are solved by finite difference analysis in the time domain to produce the discretization of a penetration system – including hammer, rod, penetrometer (or sampler) and soil. In standard penetration tests numerical simulations are shown to agree well with energy measurements derived from force and acceleration signals produced by the impact of a hammer. A parametric study allowed the identification of the relevant factors affecting penetration by demonstrating that the energy effectively delivered to the soil is a function of hammer height of fall and weight of both hammer and rods, as well as the permanent penetration of the penetrometer into the ground produced by a single stroke. Based on these evidences, an approach is suggested to compare results from different dynamic penetration tests without the need to rely on empirical correlations, which is achieved by demonstrating that different equipments should yield the same normalized energy once the influence of both the hammer and rod potential energies are properly considered. 相似文献
7.
土工格栅与土界面作用特性试验研究 总被引：9，自引：4，他引：5
土工格栅与土的界面摩擦特性指标是加筋土工程设计的关键。通过分析土工格栅与土的界面摩擦作用和进行了直剪摩擦试验和拉拔摩擦试验,测试了两种试验条件的界面摩擦特性。在两种试验条件下,土工格栅加筋土复合体的抗剪强度均有界面摩擦角φsq和界面凝聚力csq,且土工格栅与土相对位移量的不同,其复合体的强度机理有区别。在拉拔摩擦试验中,剪应力峰值强度对应的剪切变形值高于直剪摩擦试验中剪应力峰值强度的剪切变形值5～10倍以上。两种试验均有其适用性,而土与土工格栅的相对位移较小时直剪摩擦试验较能反映实际;土与土工格栅相对位移较大时土与格栅双面均发生相对位移,拉拔摩擦试验更为合适。随法向应力的增大,直剪摩擦和拉拔摩擦试验的剪应力峰值以及剪应力峰值对应的位移均提高。直剪摩擦的剪切速度小,剪应力峰值强度高,且达到峰值强度的剪切位移大;增加剪切速度,剪应力峰值强度降低,且对应的位移也减少,其原因是界面上的孔隙水压力消散和筋材的应力松弛。应根据具体工程的需要选择直剪摩擦试验和拉拔摩擦试验确定设计参数。 相似文献
8.
为了揭示黏土中静压沉桩的宏观力学特性,采用西澳大学的梁式离心机压桩系统,通过在双层高岭黏土中进行一系列1g重力场情况下的T-bar触探测试试验、静压沉桩试验、桩拉伸试验和压缩试验,对比分析了T-bar分别在均质软质黏土和双层黏土中随贯入深度变化测得的不排水剪切强度的特性;研究了桩体在贯入过程中沉桩阻力、桩端阻力以及桩侧摩阻力的发展规律;并对桩身径向总应力在沉桩过程中的变化规律进行了探讨;此外,还揭示了不同桩型沉桩终压力与桩承载力之间的关系。结果表明：在黏土中沉桩时,桩侧摩阻力在整个沉桩阻力中发挥主要的作用;对于同一土层而言,当桩超过土层分界面以下2D（D为桩径）范围后,桩端阻力并不受相邻土层性质的影响;随着压桩后时间的推移,桩侧摩阻力对承载力的时效影响较桩端阻力大。 相似文献
9.
A discrete model for unsaturated granular soils has been developed. Three discrete entities have been defined: particles, water menisci and pores. Local interaction forces and water transfer mechanisms have been integrated into a model through the appropriate equilibrium and balance equations. The results of several numerical tests using this model have been described and discussed. Simulations include wetting and drying under load tests, the application of suction cycles and the effect of a deviatoric stress ratio on wetting‐induced collapse. The model reacts just as true granular soil samples behave in laboratory tests. The model provides a new insight into the internal mechanisms leading to large‐scale features of behaviour such as wetting‐induced collapse or the increase in soil strength provided by suction. The paper also stresses that matric suction changes acting on a granular structure are capable of explaining most of the macroscopic features of stress–strain behaviour. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
10.
T型触探仪近年来在国外的海洋软土地基原位测试中得到了广泛应用,但贯入速率、地基土强度的各向异性与渐进软化等因素对于贯入阻力的影响没有得到系统的研究。在大型有限元软件ABAQUS平台上进行二次开发,针对基于Tresca屈服准则的理想弹塑性模型进行了相应改进,使之可以比较合理地反映上述因素的影响,进而对软土中T型触探仪的贯入机制进行了比较系统的数值分析。计算结果表明,贯入速率、地基土强度的各向异性与强度软化效应对于T型触探仪的贯入阻力系数影响较大。通过与有关极限分析上限解的对比分析,在一定程度上验证了有限元分析结果的合理性。 相似文献
11.
12.
Derek Elsworth 《国际地质力学数值与分析法杂志》2013,37(14):2135-2153
Rate effects are examined in the steady pore pressure distribution induced as a result of penetration of standard and ball penetrometers. The incompressible flow field, which develops around the penetrometer is used to define the approximate soil velocity field local to the penetrometer tip. This prescribes the Lagrangian framework for the migration of the fluid saturated porous medium, defining the advection of induced pore pressures relative to the pressure‐monitoring locations present on the probe face. In two separate approaches, different source functions are used to define the undrained pore fluid pressures developed either (i) on the face of the penetrometer or (ii) in the material comprising the failure zone surrounding the penetrometer tip. In the first, the sources applied at the tip face balance the volume of fluid mobilized by the piston displacement of the advancing penetrometer. Alternately, a fluid source distribution is evaluated from plasticity solutions and distributed throughout the tip process zone: for a standard penetrometer, the solution is for the expansion of a spherical cavity, and for the ball penetrometer, the solution is an elastic distribution of stresses conditioned by the limit load embedded within an infinite medium. For the standard penetrometer, the transition from drained to undrained behavior occurs over about two orders of magnitude in penetration rate for pore pressures recorded at the tip (U1) and about two‐and‐a‐half orders of magnitude for the shoulder (U2). This response is strongly influenced by the rigidity of the soil and slightly influenced by the model linking induced total stresses to pore pressures. For the ball penetrometer, the transition from drained to undrained behavior also transits two‐and‐a‐half orders of magnitude in penetration rate, although it is offset to higher dimensionless penetration rates than for standard penetration. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
13.
Coupled theory of mixtures for clayey soils 总被引：4，自引：0，他引：4
In this work, elasto-plastic coupled equations are formulated in order to describe the time-dependent deformation of saturated cohesive soils (two-phase state). Formulation of these equations is based on the principle of virtual work and the theory of mixtures for inelastic porous media. The theory of mixtures for a linear elastic porous skeleton was first developed by Biot (Theory of elasticity and consolidation for a porous anisotropic solid, Journal of Applied Physics, 1955, 26, 188–185). An extension of Biot's theory into a nonlinear inelastic media was performed by Prevost (Mechanics of continuous porous media, International Journal of Engineering Science, 1980, 18, 787–800). The saturated soil is considered as a mixture of two deformable media, the solid grains and the water. Each medium is regarded as a continuum and follows its own motion. The flow of pore-water through the voids is assumed to follow Darcy's law. The coupled equations are developed for large deformations with finite strains in an updated Lagrangian reference frame. The coupled behavior of the two-phase materials (soil-water state) is implemented in a finite element program. A modified Cam-clay model is adopted and implemented in the finite element program in order to describe the plastic behavior of clayey soils. Penetration of a piezocone penetrometer in soil is numerically simulated and implemented into a finite element program. The piezocone penetrometer is assumed to be infinitely stiff. The continuous penetration of the cone is simulated by applying an incremental vertical movement of the cone tip boundary. Results of the finite element numerical simulation are compared with experimental measurements conducted at Louisiana State University using the calibration chamber. The numerical simulation is carried out for two cases. In the first case, the interface friction between the soil and the piezocone penetrometer is neglected. In the second case, interface friction is assumed between the soil and the piezocone. The results of the numerical simulations are compared with experimental laboratory measurements. 相似文献
14.
随着全套管振动取土灌注桩施工工艺的发展,灌注桩在工程中的应用越来越广泛,但关于灌注桩套管高频振动贯入机制,特别是套管贯入引起的挤土效应研究还不全面。全面介绍了套管高频振动贯入全过程的有限元-无限元耦合模型的建立过程后,对地表隆起、土体侧移及超孔隙水压力等挤土效应的变化规律进行了详细研究。研究结果表明：水平向的挤土位移随套管贯入深度的增加而增大,竖向挤土位移随着套管贯入深度的增加,浅层土表现为隆起量增大,而深层土表现为下沉量增大;最大挤土位移与套管贯入深度存在滞后效应;浅层土体的隆起为水平向应力加载引起竖向应力增加所致,且隆起分界面深度随着动力荷载幅值增大而增大,随振动频率的增大而减小;超孔隙水压力随套管贯入深度增加而增大,随径向距离增大呈指数型衰减。 相似文献
15.
针对黄土地区深基坑降水导致地层不均匀沉降,危及坑周建筑物的问题,论文基于基坑降水诱发地面沉降机理分析,以分层总和法和剪切位移法为基础,推导出降水引起地面沉降的简化计算公式。在忽略群井效应和土层侧向变形的前提下,依据Dupuit公式得出基坑降水曲线方程,将坑周土体以降水曲线为界分为疏干区和饱和区。引入修正系数,对黄土地区不同性质土层因孔隙水压力减小产生的有效应力增量修正,同时考虑桩-土界面侧摩阻力对土体的约束作用,分别计算距井轴不同距离处的沉降量,叠加后得出最终的沉降值。对比数值模拟计算结果及工程实例监测值,分析表明:在桩-土交界处,侧摩阻力对土体竖向沉降的约束作用最明显;在1.5倍降水深度范围内的沉降计算值精度远高于规范算法,能够较好的预测降水期间黄土地区坑周不同距离处的地面沉降量。 相似文献
16.
为了探究静压沉桩与CPTU贯入力学机制,开展了饱和黏土中静压沉桩及CPTU贯入的离心模型试验,获得了静压沉桩与CPTU贯入过程中土压力、超孔压和贯入阻力的变化规律。同时,将静压桩和CPTU压入过程视为一系列球孔的连续贯入,应用圆孔扩张解答,建立了静压沉桩和CPTU贯入过程中锥头阻力、侧阻力与超孔压的预测方法。通过离心模型试验和理论预测结果的对比分析表明：随着桩体的压入,桩周土体的超孔压和土压力均逐渐增大,当桩头通过监测点时,超孔压与土压力均达到最大值;在饱和黏土中,CPTU锥头阻力、锥侧摩阻力和锥头超孔压与锥头贯入深度总体上呈线性关系。预测方法估算沉桩和CPTU贯入引起的土压力、超孔压与模型试验结果相符,较好地反映了饱和黏土中静压沉桩和CPTU贯入的力学机制。 相似文献
17.
Feng Yin Yang Xiao Hanlong Liu Hang Zhou Jian Chu 《Geotechnical and Geological Engineering》2018,36(2):783-791
In order to visually observe the displacement characteristics of internal soil, model tests on the penetration of six flat-ended piles in synthetic transparent soil were carried out. The granular-soil particles were registered by laser speckles, thus the penetration process of the piles was visualized. The movement of pile-soil interaction was determined by comparing the images before and after penetrations. Based on the test results, the vertical and horizontal displacement of the granular caused by a sequence of jacked piles was discussed. The sheltering effect of the adjacent piles during the penetration of the follow-up pile was analyzed. The responses of the granular soils during the penetration of piles were discussed, and test data was compared with DEM analyses. The pile heave at different stages of the penetration and the ground uplift at different positions were evaluated and compared. 相似文献
18.
In this paper a typical soil–structure interaction problem is considered, the case of a vertical pile installed in sand and submitted to an axial compression loading. Results from two full scale pile tests are analysed and the tests are reproduced by numerical simulations via finite elements method (FEM). The choice of the mechanical parameters for the soil and the sand–pile interface and the modelling approach are first described. A new numerical strategy is outlined to account for pile installation effects due to jacking and driving via FEM. The proposed approach is based on the application of existing empirical correlations available for the quantification of residual radial and shear stresses along the pile shaft as well as residual pressures around the pile base after the installation. This approach is proposed as an alternative to more complex methods based on the numerical modelling of the pile penetration problem. The role of the constitutive modelling of the interface is also discussed. Finally, comparative analyses of pile loading tests using FEM are provided and the comparisons between numerical and experimental results are presented and discussed. 相似文献
19.
A new finite element model based on a large strain formulation has been developed to study cone penetration in normally consolidated sand. An auto‐adaptive remeshing technique was utilized for handling the very large distortion of sand surrounding the cone tip. A frictional contact interface utilizing Mohr–Coulomb's theory was chosen to represent interactions between the surface of the cone and sand. To model the sand behaviour, the non‐associated Drucker–Prager constitutive model was selected. ABAQUS, a commercial finite element software package, was used to implement the model. The explicit solution algorithm was chosen due to its effectiveness for complicated contact problems. Analysis results proved that the model successfully captured the cone penetration behavior in sand. In addition, a chart to predict internal friction angles based on cone tip resistance for different vertical effective stresses was provided. This paper also shows a typical distribution of sleeve resistance, tip resistance—penetration relationship, and typical contours of vertical, horizontal, and shear stresses in normally consolidated sand. Finally, a non‐uniform resistance was found along the length of the friction sleeve. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
20.
Jean‐Yves Delenne Moulay Saïd El Youssoufi Fabien Cherblanc Jean‐Claude Bnet 《国际地质力学数值与分析法杂志》2004,28(15):1577-1594
We investigate the stress–strain behaviour and failure of a cohesive granular material both by experiments and numerical simulations. The material is an assembly of aluminium rods glued together by means of an epoxy resin. The behaviour of cohesive bonds (force–displacement relationship, failure conditions) is characterized by performing simple loading tests (tension/compression, shear…) on a couple of rods. Then, this local behaviour is introduced in a numerical code based on a discrete element method in order to perform numerical compression tests on large samples. The validation of this approach was the main goal of the present investigation that is essentially achieved by a direct comparison between the numerical results and similar experimental tests. As a basic application, we derive the macroscopic cohesion and friction characteristics of random cohesive materials by systematic numerical simulations in a biaxial geometry. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献