共查询到20条相似文献，搜索用时 687 毫秒
1.
The wavelet transform is used to reduce the high frequency multipath of pseudorange and carrier phase GPS double differences (DDs). This transform decomposes the DD signal, thus separating the high frequencies due to multipath effects. After the decomposition, the wavelet shrinkage is performed by thresholding to eliminate the high frequency component. Then the signal can be reconstructed without the high frequency component. We show how to choose the best threshold. Although the high frequency multipath is not the main multipath error component, its correction provides improvements of about 30% in pseudorange average residuals and 24% in carrier phases. The results also show that the ambiguity solutions become more reliable after correcting the high frequency multipath. 相似文献
2.
A new method to mitigate multipath error in single-frequency GPS receiver with wavelet transform 总被引：2，自引：1，他引：1
One of the major errors in high-precision GPS positioning is multipath. Multipath effect modeling and reduction have been a challenging issue in high-accuracy GPS positioning applications due to its special properties. Different methods have been employed to mitigate this error including hardware and software approaches. We reduce C/A code multipath error by adopting an efficient software method which uses wavelet transform as a basic data processing trend. The key idea of the proposed method is using stationary wavelet transform (SWT) in GPS signal data processing. Since we have used SWT, there is complete access to high-frequency and low-frequency terms in both time and frequency domains, and we can apply appropriated procedures to mitigate this error. The multipath error mostly is a low-frequency term. In our proposed method, the double difference (DD) residuals are applied to the SWT to identify the multipath disturbance. The extracted multipath is then used to correct DD observations. Our experiments include three data sets to investigate the proposed method and compare it with existing algorithms. We used simulations for two of these data sets. The results indicate the efficiency of the proposed method over existing algorithms. 相似文献
3.
伪距多路径误差是影响GNSS导航定位精度的主要误差源之一。多路径误差与接收机周围环境有关,在实际应用中难以建立有效的多路径误差模型进行改正。对于多频GNSS接收机可以通过多频观测值组合估计伪距多路径,但该方法不适用于价格低廉的单频接收机,而导航中使用的大多数为单频接收机。因此,开展单频GNSS伪距多路径误差提取研究具有重要的工程应用价值。本文基于小波分析对单频GNSS接收机伪距多路径误差估计开展研究,首先验证了小波分析用于单频GNSS伪距多路径误差估计的可行性;其次,研究了采用不同的小波基和分解层次对多路径误差估计的影响;最后,研究了改正多路径误差对GNSS定位的影响。实验结果表明不同的小波基和分解层次对多路径误差提取效果没有明显的差别,但小波分解层次较低时定位误差分布相对更加集中,同时,经过多路径误差改正后在NEU3个方向RMS平均改善率达到20.4%、25.1%、16.4%。 相似文献
4.
Wavelet packets based denoising method for measurement domain repeat-time multipath filtering in GPS static high-precision positioning 总被引：1，自引：1，他引：0
Lawrence Lau 《GPS Solutions》2017,21(2):461-474
Repeatable satellite orbits can be used for multipath mitigation in GPS-based deformation monitoring and other high-precision GPS applications that involve continuous observation with static antennas. Multipath signals at a static station repeat when the GPS constellation repeats given the same site environment. Repeat-time multipath filtering techniques need noise reduction methods to remove the white noise in carrier phase measurement residuals in order to retrieve the carrier phase multipath corrections for the next day. We propose a generic and robust three-level wavelet packets based denoising method for repeat-time-based carrier phase multipath filtering in relative positioning; the method does not need tuning to work with different data sets. The proposed denoising method is tested rigorously and compared with two other denoising methods. Three rooftop data sets collected at the University of Nottingham Ningbo China and two data sets collected at three Southern California Integrated GPS Network high-rate stations are used in the performance assessment. Test results of the wavelet packets denoising method are compared with the results of the resistor–capacitor (RC) low-pass filter and the single-level discrete wavelet transform (DWT) denoising method. Multipath mitigation efficiency in carrier phase measurement domain is shown by spectrum analysis of two selected satellites in two data sets. The positioning performance of the repeat-time-based multipath filtering techniques is assessed. The results show that the performance of the three noise reduction techniques is about 1–46 % improvement on positioning accuracy when compared with no multipath filtering. The statistical results show that the wavelet packets based denoising method is always better than the RC filter by 2–4 %, and better than the DWT method by 6–15 %. These results suggest that the proposed wavelet packets based denoising method is better than both the DWT method and the relatively simple RC low-pass filter for noise reduction in multipath filtering. However, the wavelet packets based denoising method is not significantly better than the RC filter. 相似文献
5.
A new multipath mitigation method based on adaptive thresholding wavelet denoising and double reference shift strategy 总被引：1，自引：0，他引：1
Multipath disturbance is one of the major error sources in high-accuracy positioning for global navigation satellite system (GNSS). Although various methods based on software and hardware strategies have been developed to mitigate this error, they are still limited by different kinds of factors and the effect is not ideal. After analyzing the existing methods, a new single-difference sidereal filtering method, based on adaptive thresholding wavelet denoising and double reference shift strategy (ATDR), is proposed to mitigate multipath effects for static short-baseline GNSS applications. The key idea of the proposed method is the use of both the adaptive thresholding wavelet denoising to extract an accurate multipath correction model from the reference Day and the double reference shift strategy to mitigate multipath for subsequent Day 2 more accurately and efficiently. By applying the introduced adaptive thresholding method, the average improvement rate of the RMS values of the single-difference residuals can reach about 15.82% compared with the constant thresholding method. Moreover, after applying the proposed ATDR method, the 3D positioning precision is improved by about 37.73% for the single epoch mode with 30 s data sampling rate and about 31.22% for the continuous mode with 1 s high sampling rate compared with the original results. Even compared with the constant thresholding single orbital reference (CTSR) method, the improvement percentage is about 33.94% in single epoch mode and about 25.40% in continuous mode for 3D positioning precision, respectively. In conclusion, the results of the two experiments indicate that the proposed ATDR method performs much better than the CTSR method in mitigating multipath for different sampling rates and different processing modes in the measurement domain for GNSS static short-baseline postprocessing applications. 相似文献
6.
针对测站观测环境变化对数据质量影响难以有效评估并削弱的问题,研究了一种可通用于各类卫星导航系统的多路径误差半天球格网点建模方法（multi-point hemispherical grid model,MHGM）。该方法能够综合利用不同GNSS（global navigation satellite system）系统的不同时期观测数据进行整体建模,显著削弱GNSS信号所受多路径误差影响,并图像化反演测站周围的多路径效应,确定信号干扰源的方位。算例的测试结果表明,在模拟的强多路径环境下,模型改正后模糊度固定时段的载波相位观测值残差的均方根误差（root mean square error,RMSE）统计值由0.983 cm降为0.318 cm,改善率高达67.7%。此外,MHGM建模结果中改正量较大的异常区域与对应测站处所架设挡板的方位相一致,能够反演出测站周围不同方向观测信号所受多路径误差影响。国际GNSS服务组织的历史观测数据在利用MHGM模型改正后,合计18年测试算例的观测值残差RMSE平均改善率达到29.5%。这对于评估测站观测环境在不同时期的变化状况,提升现有各类增强服务产品的精度和可靠性具有一定的潜在应用价值。 相似文献
7.
8.
在全球导航卫星系统(Global Navigation Satellite System,GNSS)接收机附近的反射、衍射、干扰信号等所造成的多路径效应是影响定位的主要误差来源。信噪比(Signal-Noise Ratio,SNR)的振荡是由多路径信号叠加在直接信号上引起的,基于此原理学者们提出了很多检测和缓解多路径误差的方法。本文通过谱分析的方法对多路径时间序列进行了分析,并研究多路径与信噪比之间的相关性,对基于信噪比检测和缓解多路径误差的方法的适用性进行了说明。实验表明:多路径和信噪比振荡值的时间序列具有显著的相关性,能够利用信噪比观测值削弱多路径影响。 相似文献
9.
Multipath mitigation via component analysis methods for GPS dynamic deformation monitoring 总被引：1，自引：0，他引：1
Multipath is one of the main error sources in high-precision global positioning system (GPS) dynamic deformation monitoring, as it is difficult to be mitigated by differencing between observations. In addition, since a specific frequency threshold value between multipath and deformation signals may not exist, multipath is usually inseparable from the low-frequency vibration signal using conventional frequency-domain filter methods. However, the multipath repeats in two sidereal days when the surroundings of a GPS antenna remain unchanged. This characteristic can be exploited to model and thus mitigate multipath effectively in dynamic deformation monitoring. Unfortunately, a major issue is that the degree of repeatability decreases as the interval between first day and subsequent days increases. To overcome this problem, we develop a new sidereal filtering referred to as reference EMD-ICA (EMD-ICA-R), where empirical mode decomposition (EMD) and independent component analysis (ICA) are jointly used to model multipath and renew the reference multipath. For the successful implementation of the EMD-ICA-R, an a priori denoised multipath signal is needed as a reference. We further propose to use the principal component analysis (PCA) method to extract more accurate reference multipath signal and form a combined PCA-EMD-ICA-R approach. Simulation experiments with a motion simulation platform were conducted, and the testing results indicate that the proposed methods can mitigate the multipath by around 67 % when a reliable reference multipath signal is extracted from a static situation. Furthermore, simulation experiments with different deformation signals added into the coordinate time series of three consecutive days show that the two proposed methods are also effective in a dynamic situation. Since wavelet filtering is used to denoise the reference multipath signals in the new approaches, simulation experiments with several wavelet filters are tested, and the results indicate that the PCA-EMD-ICA-R approach can work well with various wavelet filters. 相似文献
10.
全球卫星导航系统（GNSS）多径信号广泛存在于城市峡谷等复杂导航定位场景中. 多径信号在干扰GNSS接收机并造成系统定位精度下降的同时,也为接收机提供了周边反射面环境信息. 在码相位延迟幅度联合跟踪算法（CADLL）实现GNSS多径信号感知和特征参数提取的基础上,设计实现了基于粒子滤波的反射面参数估计算法. 该算法可以在GNSS多径环境中增强接收机的环境感知能力,相关环境信息可应用于场景感知、避障、路径规划和定位增强等领域. 静态环境下进行GNSS多径信号采集和算法测试,实验结果表明该算法能够有效估计反射面位置参数,反射面方位角均方根误差（RMSE）小于10°,反射面俯仰角RMSE小于5°,反射面距离RMSE小于10 m. 相似文献
11.
基于小波与遗传算法的特征提取与特征选择 总被引：5，自引：0，他引：5
高维遥感数据的分类与识别与传统的多光谱遥感分类技术具有明显的区别。本文提出了一种基于遗传算法和小波／小波包分析相结合的特征提取方法用于高维遥感数据降维与分类。该方法综合了遗传算法的全局优化和小波／小波包分析的多尺度、多分辨率的特点。首先,通过离散的小波变换(DWT)或小波包变换(WP)将高光谱信号变换到特征域进行光谱分解。由于DWT变换是一种线性变换,不同尺度的DWT系数可作为线性光谱特征。然后,对这些线性光谱特征利用遗传算法结合训练样本计算类内／类间距离搜索最优分类子集,其具体染色体编码取可能的特征号,适应度函数基于样本平均Jeffries-Matusita距离计算。所用的分类器采用最大似然分类器。试验结果表明该方法与常规特征提取算法如主成分变换(PCA)、判别分析特征提取(DAFE)、决策边界特征提取(DBFE)相比,能提高分类精度约1.1％-6.5％。 相似文献
12.
Multipath on carrier phase measurements is among the major error sources for short baseline positioning. A new method is proposed
to improve the accuracy of the positioning results by mitigating the multipath effects on carrier phase measurements using
the variable length Least Mean Square (VLLMS) adaptive filter. The performance of the filter is analyzed as well as compared
with that of the standard LMS adaptive filter using a set of carrier phase observation data of two consecutive days collected
in a short baseline experiment. Because the two antennas are static, the multipath error is the only dominant component in
the carrier phase double-differenced residuals and indicates a repeated pattern. The numerical results show that both filters
can significantly mitigate the multipath effects in carrier phase double-differenced residuals, and hence improve the positioning
results. Furthermore, the VLLMS filter that reduces up to about 47.4% of the multipath effects on 3D positioning performs
better than the LMS filter that only reduces 22.0%. Both filters are suitable for real-time applications. 相似文献
13.
Multipath is one of the most important error sources in Global Navigation Satellite System (GNSS) carrier-phase-based precise
relative positioning. Its theoretical maximum is a quarter of the carrier wavelength (about 4.8 cm for the Global Positioning
System (GPS) L1 carrier) and, although it rarely reaches this size, it must clearly be mitigated if millimetre-accuracy positioning
is to be achieved. In most static applications, this may be accomplished by averaging over a sufficiently long period of observation,
but in kinematic applications, a modelling approach must be used. This paper is concerned with one such approach: the use
of ray-tracing to reconstruct the error and therefore remove it. In order to apply such an approach, it is necessary to have
a detailed understanding of the signal transmitted from the satellite, the reflection process, the antenna characteristics
and the way that the reflected and direct signal are processed within the receiver. This paper reviews all of these and introduces
a formal ray-tracing method for multipath estimation based on precise knowledge of the satellite–reflector–antenna geometry
and of the reflector material and antenna characteristics. It is validated experimentally using GPS signals reflected from
metal, water and a brick building, and is shown to be able to model most of the main multipath characteristics. The method
will have important practical applications for correcting for multipath in well-constrained environments (such as at base
stations for local area GPS networks, at International GNSS Service (IGS) reference stations, and on spacecraft), and it can
be used to simulate realistic multipath errors for various performance analyses in high-precision positioning. 相似文献
14.
A. El-Mowafy 《GPS Solutions》2014,18(4):553-561
A method is presented for real-time validation of GNSS measurements of a single receiver, where data from each satellite are independently processed. A geometry-free observation model is used with a reparameterized form of the unknowns to overcome rank deficiency of the model. The ionosphere error and non-constant biases such as multipath are assumed changing relatively smoothly as a function of time. Data validation and detection of errors are based on statistical testing of the observation residuals using the detection–identification–adaptation approach. The method is applicable to any GNSS with any number of frequencies. The performance of validation method was evaluated using multi-frequency data from three GNSS (GPS, GLONASS, and Galileo) that span 3 days in a test site at Curtin University, Australia. Performance of the method in detection and identification of outliers in code observations, and detection of cycle slips in phase data were examined. Results show that the success rate vary according to precision of observations and their number as well as size of the errors. The method capability is demonstrated when processing four IOV Galileo satellites in a single-point-positioning mode and in another test by comparing its performance with Bernese software in detection of cycle slips in precise point-positioning processing using GPS data. 相似文献
15.
在利用北斗卫星导航系统（BDS）进行高精度变形监测时,BDS信号产生的多路径效应是影响变形监测数据精度和可靠性的一个不可忽视的误差源. BDS有三种不同的轨道卫星,所形成的多路径误差较为复杂. 基于坐标域的多路径误差使用小波分析(Wavelet)和经验模态分解(EMD)进行原始序列降噪,对降噪后序列使用改进恒星日滤波(ASF)进行多路径误差剔除,两种方法分别对基线精度的E方向改善了38.6％和40.8％,N方向改善了59.1％和61.0％,U方向改善了57.8％和57.9％,EMD对坐标序列的平滑和基线精度改善较优. 相似文献
16.
We present a signal processing approach using discrete wavelet transform (DWT) for the generation of complex synthetic aperture radar (SAR) images at an arbitrary number of dyadic scales of resolution. The method is computationally efficient and is free from significant system-imposed limitations present in traditional subaperture-based multiresolution image formation. Problems due to aliasing associated with biorthogonal decomposition of the complex signals are addressed. The lifting scheme of DWT is adapted to handle complex signal approximations and employed to further enhance the computational efficiency. Multiresolution SAR images formed by the proposed method are presented. 相似文献
17.
为了有效地提取GNSS站坐标时间序列的有用信息，降低噪声干扰，本文提出一种局部均值分解和奇异值分解相结合的信号降噪方法，并利用5个测站的实测坐标时间序列对新方法进行了验证。首先通过局部均值分解将坐标时间序列分解成一系列PF分量和余项，然后利用连续均方误差方法确定高频分量与低频分量的分界点，保持低频分量不变，运用奇异值分解方法对高频分量进行降噪重构，最后将重构的高频分量与低频分量叠加得到最终的降噪坐标时间序列，并对降噪效果进行对比分析。结果表明，与单纯的奇异值分解方法相比，局部均值分解和奇异值分解相结合方法能够自适应地选择合适的奇异值个数进行信号重构，提高了降噪效果。 相似文献
18.
考虑到全球导航卫星系统(global navigation satellite system,GNSS)地震信号的非线性和非平稳性,利用一种多尺度多方向主成分分析(multiscale multiway principal component analysis,MSMPCA)去噪的完备总体经验模态分解(complete... 相似文献
19.
HUANG Shengxiang JIN Xiangsheng YANG Baocen 《地球空间信息科学学报》2006,9(2):79-83
IntroductionThere are many factors that affect the precisionand reliability of GPS measuring. Generally, theerror sources can be grouped into the followingthree classes: errors correlated with the satellites(such as ephemeris error, satellite clock error,… 相似文献
20.
袁兴明 《测绘与空间地理信息》2020,(4):189-193,196
GNSS坐标在观测过程中受多方面因素影响,产生各种误差,存在一些波动变化,根据波动变化特征可以分析探测存在的信号。本文主要利用功率谱、小波谱和小波熵对GNSS原始、去趋势项、差分处理3种情况下时间序列进行分析,通过对比显示,小波谱和小波熵对于非平稳信号探测比功率谱分析能力强,GNSS时间序列存在一个趋势项和一个年周期信号。 相似文献