共查询到19条相似文献，搜索用时 145 毫秒
1.
2.
海上风电工程主要受到风、波浪及洋流等产生的水平循环荷载作用,本文研究楔形单桩基础在水平循环荷载作用下的变形规律,并探讨不同循环荷载对变形规律产生的影响,以确保风电设施正常运行。通过数值模拟建立海上风电单桩-海床模型,考虑土体超孔隙水压力的演变规律及土体致密规律,土体采用UBC3D-PLM本构模型。本文重点讨论并分析在不同水平循环荷载作用下楔形单桩基础与等截面单桩基础的桩周土体位移、塑性应变及桩基累计转角位移之间的差异。研究结果表明：楔形结构会降低桩周土体位移及塑性应变,使得楔形单桩基础旋转中心位置更低,产生倾覆的可能更小,当循环荷载比为0.7时,累计转角位移能减少41.86%;循环荷载越大,楔形单桩基础水平受荷特性越好,累计位移减少量的增长率越高。研究成果可为今后海上风电基础的选择与设计提供参考。 相似文献
3.
《中国海洋大学学报(自然科学版)》2017,(10)
大直径钢管桩在海洋工程建设中的使用越来越广泛。海上大直径钢管桩试桩周期长、难度大,相关测试数据及研究成果较为少见。本文基于美国石油行业协会API规范,分析了某海上风电大直径钢管桩静压载试验数据,研究了桩侧阻力与桩端阻力随压荷载变化关系。结果表明,对于本文分析的海上大直径钢管桩,其土塞状态一般为不完全闭塞,计算抗压极限承载力时应计入桩管内侧摩阻力;桩侧摩阻力随压荷载增大而逐渐发挥,相同荷载作用下,无黏性土地层侧摩阻力发挥程度较黏性土高;桩端土体破坏分为弹性变形与塑性变形两个阶段,两阶段端阻发挥程度分别可达约50%和80%,当桩端产生0.05d位移时,桩体达到极限平衡状态。 相似文献
4.
江苏海岸辐射沙洲是江苏重要的海上风电规划区域,该海域的地层资料和试桩资料极为缺乏。通过钢管桩的现场静荷载试验,对江苏海岸辐射沙洲地层中大直径钢管桩基础承载性能进行研究,以揭示各地层的主要承载性能参数。试桩结果表明,江苏海岸辐射沙洲地层中钢管桩实际的轴向极限承载力明显小于高应变动测结果,只有高应变动测结果的79.09%。总侧摩擦阻力占总承载力的95.61%,而桩端阻力只占总承载力的4.39%。桩内土对管壁的侧摩阻力作用很小,主要是桩外土对管壁的侧摩阻力在发挥作用。辐射沙洲地层中粉土夹粉质黏土的承载性能一般,不适应作为钢管桩的持力层。轴向抗压静载试验得到的极限侧摩阻力高于静力触探的测试结果和API法的计算值。浅部砂层实际的极限水平土体抗力高于API法计算值,在水平荷载作用下上部砂层的p-y曲线具有明显软化效应,土体的软化效应在设计时需进行考虑。 相似文献
5.
《中国海洋大学学报(自然科学版)》2017,(8)
单桩基础是海上风电场的一种重要基础形式。海上风电场单桩基础首先需要承担上部结构传递的竖向荷载,然后还需要承受波浪、海流、地震等作用下的水平荷载,而既有竖向荷载对单桩的水平承载特性会产生重要影响。本文阐述了既有竖向荷载对单桩水平承载特性影响的研究进展。通过对比不同学者的研究成果,分析了既有竖向荷载对单桩水平承载力特性的影响规律、影响原因及影响因素。针对目前国内外学者对该问题研究的不足,提出了若干思考和展望,认为有必要进行影响因素分析和水平循环荷载影响的探究。 相似文献
6.
水平荷载下海上风机单桩基础桩土相互作用研究 总被引：1，自引：0，他引：1
《中国海洋大学学报(自然科学版)》2016,(3)
海上风电作为一种清洁绿色的能源越来越受到人们的关注,海上风机会承受风、浪、流等水平荷载的作用,因此水平荷载下海上风机单桩基础桩土相互作用一直是人们研究的热点。本文对水平荷载作用下海上风机单桩基土相互作用进行研究,通过ABAQUS有限元数值分析软件建立桩土模型。结果显示:桩顶水平极限位移约为11.25cm,海床面以下1~5m范围为桩身弯矩和桩身mises应力较大的区段;随着桩顶水平位移的逐渐增大,桩身挠曲逐渐向深处发展,桩体位移零点位置逐渐向下;桩体的水平位移会对桩侧土体产生挤压作用,这种挤压作用会使土体塑性屈服区逐渐向下发展,土体水平位移呈半圆形放射状分布,浅层土体mises应力产生非对称分布。 相似文献
7.
《中国海洋大学学报(自然科学版)》2017,(4)
基于室内土工动三轴土体液化试验,采用有限元分析计算与剪应力比较法相结合的综合判别方法,对于黄河三角洲地区海上风电单桩基础周围土体是否会液化进行了判断,并且通过对比不同位置处土体单元受力情况,总结出单桩基础的存在对于其周围土体地震荷载作用下动力响应的影响。研究发现,土体液化只会在一定深度内发生,12m以下土体由于上覆有效应力较大基本不会发生液化。单桩基础对于桩内土体约束作用十分明显,同时会剧烈加大桩侧土体的受力。本文通过对土体施加X轴方向上的加速度的方式模拟地震作用,结果显示,位于单桩基础X轴方向上的土体单元相较于Y轴方向上等距离的土体单元,受到的剪应力振荡幅度要大的多。 相似文献
8.
近海海床表层多为软黏土或淤泥质土,为探究海床表层软土对海上风电宽浅式筒型基础承载特性的影响,以中国广东某海域风电场为背景,通过有限元分析的方法,研究竖向、水平、弯矩荷载作用下软土层厚度和土体强度对基础极限承载力、破坏模式以及筒基土压力分布的影响。研究结果表明:当软土层厚度小于H/2(H为筒裙高度)时,单向荷载作用下宽浅式筒型基础极限承载力随软土层厚度的增加呈线性减小的趋势;当软土层厚度大于H/2后,承载力降低速率逐渐增大。表层软土的存在,使得塑性区范围缩小,软土层内土体塑性破坏更加明显。竖向荷载作用下,随软土层厚度的增大,筒顶承载先减小后增大,筒内侧摩阻力先增大后减小;水平荷载和弯矩作用下,筒侧被动土压力的降低是引起软土覆盖地基中基础承载能力降低的主要因素。 相似文献
9.
统计数据表明,单桩基础在海上风机基础形式中所占比例为65%以上,开展单桩基础设计与分析方法的研究具有重要的工程应用意义。根据海上风电机组基础所处的环境特点和结构特性,介绍了海上风机单桩基础的设计要点。结合某海上风电场风电机组单桩基础设计实例,建立了单桩基础有限元模型,进行了基础承载力与变形计算、模态分析和疲劳分析等工作,给出了相关设计成果,可供相关设计人员参照使用。 相似文献
10.
利用modeling of models的方法研究端承型桩承载力离心模型试验中的粒径效应。在模拟同一原型时,不同桩径的模型桩,桩身压缩性及桩长均不同,导致侧摩阻力发挥机理及程度不同,本文分别探讨了桩端阻力,侧摩阻力及承载力(桩顶荷载)的粒径效应对承载机理和承载特性的影响。结果表明,桩端阻力的粒径效应作用规律与浅基础一致,可以借用浅基础的粒径效应定量评价方法评价端承桩承载力离心模型试验中的粒径效应。侧摩阻力的粒径效应比桩端阻力的粒径效应显著。由于侧摩阻力的影响,相同条件下承载力的粒径效应比桩端阻力有所增强。对于极限桩端阻力和极限承载力,粒径效应均随长径比的增加而减弱。 相似文献
11.
p-y 曲线法在水平受荷桩的设计中得到了广泛应用,然而近年来在海上风机超大直径单桩基础设计中受到了学术界和工程界的质疑,当前研究表明,桩基尺寸是产生这一问题的主要原因。本文通过三维数值仿真技术,研究了砂土地基中水平受荷桩-土作用特征的演变规律,探讨了当前超大直径单桩设计方法存在的主要问题及产生的原因。计算结果显示：超大直径单桩基础因其桩径大、长径比（入土长度与直径的比） 小的尺寸特征,在水平荷载作用下桩土作用具有明显的三维空间效应,即除受水平向土反力外,还受到桩端水平向的摩擦力、沿桩身不均匀摩阻力产生的抵抗力矩及桩底不均匀土反力提供的抵抗力矩;进一步研究表明,后三类抗力对桩基水平承载力的贡献占比与桩基尺寸有关,即桩基直径越大、长径比越小,这些抗力的贡献越大。因此,在水平受荷超大直径单桩承载特性计算与分析的过程中,除当前水平向p-y 弹簧提供的抗力外,还应考虑桩底的水平剪力、桩身摩擦力和桩底反力不平衡产生的抵抗力矩。 相似文献
12.
AbstractThis study established a Couple Eulerian–Lagrange model to simulate monopile vibratory penetration for the investigation of soil plugging effect during high-frequency penetration of monopiles for wind turbine. Simulation analysis is focused particularly on soil plugging effect of a large diameter monopile during vibratory penetration into sand, clay, or layered soil. The results of the numerical simulation show that soil plugging effect is unlikely to occur during monopile penetration into the clay soil, while partial soil plugging may occur during the sand penetration. Penetration resistance at the pile toe is transferred to the radial stress around the pile wall. At a critical point penetration process, internal shaft friction becomes larger than external shaft friction. Moreover, radial pressure factors increase during partial soil plugging effect. For layered soil, the topsoil not only has great influence on the soil plugging effect, but also affects shaft friction in the subsoil during monopile penetration. 相似文献
13.
为改善海上风电大直径钢管桩的水平承载性能,基于ABAQUS有限元软件对单桩改进形式的加翼桩结构进行了系统研究,计算分析了软黏土地基中加翼桩在水平荷载作用下桩身弯矩、应力、位移、桩身泥面处倾斜率和极限承载力,研究了加翼桩面积、形状、埋深和刚度等翼板参数对加翼桩水平承载性能的影响规律,根据加翼桩的桩-土作用机理,参考现行规范模式提出适用于软黏土地基大直径钢管桩的P-Y曲线。研究结果表明,加翼桩通过在泥面处设置翼板可降低桩基泥面处倾斜率50%、提高桩基极限承载力60%以上,加翼桩水平承载性能明显优于单桩。 相似文献
14.
Offshore wind turbines (OWTs) are generally supported by large-diameter monopiles, with the combination of axial forces, lateral forces, bending moments, and torsional moments generated by the OWT structure and various environmental factors resisted by earth pressures mobilized in the soil foundation. The lateral loading on the monopile foundation is essentially cyclic in nature and typically of low amplitude. This state-of-the-art review paper presents details on the geometric design, nominal size, and structural and environmental loading for existing and planned OWT structures supported by monopile foundations. Pertinent ocean-environment loading conditions, including methods of calculation using site-specific data, are described along with wave particle kinematics, focusing on correlations between the loading frequency and natural vibration frequency of the OWT structure. Existing methods for modeling soil under cyclic loading are reviewed, focusing in particular on strain accumulation models that consider pile–soil interaction under cyclic lateral loading. Inherent limitations/shortcomings of these models for the analysis and design of existing and planned OWT monopile foundations are discussed. A design example of an OWT support structure having a monopile foundation system is presented. Target areas for further research by the wind-energy sector, which would facilitate the development of improved analyses/design methods for offshore monopiles, are identified. 相似文献
15.
Lu Ma 《Marine Georesources & Geotechnology》2017,35(2):275-280
Monopiles are considered to be as a kind of viable foundation types for offshore wind turbines. The effect of negative skin friction on pile foundation is always an important problem. There are very important theoretical and practical significance to study the distribution law of negative skin friction and the calculation method. Based on the special stratum, the stress and strain of the monopile and soil are simplified, and the improved Kezdi’s double-broken-line model is adopted. The analytical solution of negative skin friction of monopile is deduced according to the degree of skin friction. An engineering case was analyzed by the method, and the calculated results agree well with the measured data. The calculation method proposed can accurately describe the range of the monopile skin frictional distribution and the position of the neutral point, and it is simple and convenient to calculate, that is also a feasible method for calculating the negative skin friction of monopile of offshore wind turbines in practical engineering. 相似文献
16.
Large diameter monopiles are typical foundation solutions for offshore wind turbines. In design of the monopile foundations in sand, it is necessary to understand the drainage conditions of the foundation soil under the design loading conditions as the soil performance (strength and stiffness) is highly dependent on the drainage conditions. This paper presents a numerical investigation into this issue, with a purpose to develop a simple design criterion for assessing the soil drainage conditions around a monopile in sand. It is found that for typical monopile foundations in sand, the drainage condition during a single load cycle is generally expected to be undrained. However, the current state-of-practice uses p-y springs derived for drained soil responses for monopile design. The impact of this discrepancy on monopile foundation design was evaluated and found to be insignificant due to the relatively low level of loading as compared to the capacity of the soil. 相似文献
17.
Large monopiles are used as foundations for offshore wind turbines and are generally designed with a tapered section or conical shape. Some loss of driving energy is expected to occur during installation of these structures due to the submerged section of the tapered monopile. The current literature on this subject is limited and indicates rather large losses compared to field observations.A numerical model of the monopile–water–soil system was set up in the general-purpose finite element package Abaqus. By simulating the hammer impact and the resulting stress wave propagation through the monopile and water, the energy losses to be expected can be calculated accurately. The model was verified against independent finite element analyses and experimental data.A parametric study was performed and the effect of hammer characteristics, submerged monopile length and monopile geometry on the driving energy losses were quantified. The results enable a simple relationship between the energy losses and the monopile geometry to be proposed which increases linearly with pile diameter, taper angle, and submerged length. The losses are typically on the order of 0.15–0.3% per metre submerged length for large tapered monopiles. 相似文献
18.
The eigenfrequency of offshore wind turbine structures is a crucial design parameter, since it determines the dynamic behavior of the structure and with that the fatigue loads for the structural design. For offshore wind turbines founded on monopiles, the rotational stiffness of the monopile-soil system for un- and reloading states strongly affects the eigenfrequency. A numerical model for the calculation of the monopile’s behavior under un- and reloading is established and validated by back-calculation of model and field tests. With this model, a parametric study is conducted in which pile geometry, soil parameters and load conditions are varied. It is shown that of course the rotational stiffness varies with mean load and magnitude of the considered un- and reloading span, but that for most relevant load situations the initial rotational stiffness of the monopile system, i.e. the initial slope of the moment-rotation curve for monotonic loading, gives a good estimate of the actual stiffness. Comparisons of different p–y approaches show that the ordinary API approach considerably underestimates the initial stiffness, whereas the recently developed ‘Thieken’ approach and also the ‘Kallehave’ approach give a much better prediction and thus might be used in the design of monopiles in sand. 相似文献
19.
用于海洋平台的吸力式桩桶基础作为一种新型平台基础正逐渐成为人们研究的重点。为研究吸力式桩桶单桩基础的受力特性,对V-H（竖向—水平）联合荷载作用下的吸力式单桩基础桩土的承载特性进行了数值模拟,并将数值模拟的有限元解通过与API规范中对p-y曲线的计算方法进行对比来验证有限元模型的可行性,最后采用分级作用力的加载方式对其破坏包络曲线进行绘制,并推导出相应的函数表达式。研究表明,采用ABAQUS有限元分析软件对吸力式桩桶进行数值模拟是可行的,随着对吸力式桩桶所施加V-H联合荷载的不断增大,吸力式桩桶所能体现的应力和弯矩极限值也在随之增大,其位移变化主要在施加荷载的区域附近,最后在联合荷载作用下所体现的极限承载状态,即包络曲线大致呈四分之一的椭圆形状。 相似文献