共查询到18条相似文献，搜索用时 442 毫秒
1.
深基坑平面内支撑结构等效刚度的计算常采用有限元等数值计算方法,通过分析深基坑支护结构的4种典型平面内支撑结构型式,探讨了数值计算模型中内支撑结构的单元划分长度、约束弹簧刚度、约束弹簧间距、约束弹簧布置型式等因素对内支撑等效刚度计算结果的影响.经计算分析可知,在其他影响因素不变而只改变某个影响因素时,平面内支撑结构的等效刚度随腰梁单元长度的增加、约束弹簧刚度的增加呈增加的趋势,随约束弹簧间距的增加呈降低的趋势,但基本不受约束弹簧布置型式、除腰梁之外的其他内支撑构件单元长度的影响.在此基础上,得出了数值计算中上述各影响因素的建议取值范围和约束弹簧的布置型式. 相似文献
2.
脐带缆用于连接水上浮体和水下生产系统,缆芯由钢管单元、光纤单元和电缆单元等组装而成,缆体外层是由铠装钢丝层螺旋缠绕以及聚合物外护套组装而成,截面结构复杂。利用ANSYS有限元通用软件建立双层铠装脐带缆的三维多层接触摩擦有限元模型,计算其截面拉伸刚度,将拉伸刚度数值模拟值与理论结果进行对比,验证有限元模型的正确性;分析比较铠装层不同缠绕角度、缠绕方式和钢丝直径下脐带缆模型的拉伸刚度。结果表明:铠装钢丝层缠绕方式、缠绕角度、铠装钢丝直径对双层铠装脐带缆模型的拉伸刚度、最大等效应力模拟结果均有影响。 相似文献
3.
具有裂纹损伤桩腿的海洋石油平台有限元分析 总被引：3，自引：0，他引：3
采用有限元分析方法和断裂力学方法,将含裂纹构件的裂纹以线弹簧处理,建立了带有裂纹损伤桩腿的等效梁和管单元的单元刚度矩阵的计算方法。对检验方法的正确性,使用该方法对几种损伤构件进行了强度计算,并与有限元细化网格计算结果和实验结果进行比较,最后将等效单元计算程序接入大型有限元程序ＳｕｐｅｒＳＡＰ,对受损后的平台整体结构进行了应力计算和强度分析。 相似文献
4.
脐带缆是连接平台或浮式生产系统与海底油井的控制管缆,缆芯由管单元、光纤单元、电缆单元、以及填充单元组装而成,缆体外层由铠装钢丝螺旋缠绕和聚合物护套组成。基于ANSYS有限元软件,建立无铠装含填充的钢管脐带缆三维有限元模型,在自由端可扭转、不可扭转约束条件下,计算模型的拉伸刚度,将拉伸刚度的数值模拟与理论结果进行对比,验证有限元模型的正确性;分析比较含填充与不含填充两种截面形式脐带缆模型的力学性能,结果表明:填充单元、拉伸率对脐带缆模型的拉伸刚度、最大等效应力模拟结果均有影响。 相似文献
5.
周向变刚度环肋圆柱壳应力分析研究 总被引：1，自引：0，他引：1
采用大曲率梁理论和弹性基础梁带理论,建立潜艇特殊舱段结构的力学模型。利用能量法求出肋位处耐压船体壳板中面周向应力。建立环肋圆柱壳微分方程并根据边界条件求解,得到周向变刚度环肋圆柱壳应力计算方法。通过理论分析和模型试验验证了本计算方法。 相似文献
6.
提出了一种将波浪中倾斜板问题等效化简为波浪中水平板单元组的方法,该方法建立在使用分离变量法求解水工结构边值问题的基础上,并使用伽辽金法精确求解连续边界条件,确定考虑衰减波态的速度势函数,从而求解没水倾斜板结构的消波性能。等效化简法计算精度于边界元法相当,且计算单元数量少、开销低。基于二维线性势波理论,对没水倾斜板式防波堤消波性能分析显示,没水板的倾斜角度、没水深度与板长是结构消波性能的控制因素:没水倾斜板防波堤的消波性能优于没水水平板防波堤的消波性能,随着没水板结构的倾斜角度增大,没水倾斜板结构的波浪透射系数显著减小,且长板优于短板,浅板优于深板;与前人的水槽实验对比显示,相对没水深度与波陡影响结构的消波性能,且波陡造成的波浪破碎贡献了显著的波能消耗。该结论对板式防波堤的结构配置、优化设计有重要意义。 相似文献
7.
针对格型钢板桩结构的三种建模方法(考虑板桩间铰接特性,用壳体单元模拟板桩的有限元模型;不考虑板桩间铰接特性,用壳体单元模拟板桩的有限元模型;将格体看做一个整体,用实体单元模拟板桩的有限元模型)进行分析,对各种建模方法得出的关于稳定性、破坏模式、格体环向应力、格体内外土体压力的相关结论进行比较,得到适合工程应用的建模方法。结果表明:三种有限元模型中,考虑板桩间铰接特性的壳体单元模型,因其考虑因素全面,是最准确的模型。对于重要工程,应采用考虑板桩间铰接特性的壳体单元模型进行计算。对于一般工程结构,在稳定性分析方面,三种有限元模型都很适用,由于壳体单元模型收敛性较差,建议采用比较成熟的实体单元模型进行简化;对于破坏模式和板桩间环向应力,建议采用不考虑板桩间铰接作用的壳体单元模型进行简化;对于结构背浪侧格型钢板桩结构格体外侧土体最大被动土压力和格内土体压力,采用不考虑板桩间铰接特性的壳体单元模型进行估算。结论对工程数值建模运算具有指导意义。 相似文献
8.
《中国海洋大学学报(自然科学版)》2021,(11)
本文基于ABAQUS有限元软件,建立非粘结钢管脐带缆的三维有限元模型计算其弯曲刚度,将弯曲刚度的数值模拟与理论结果进行对比,验证了模型的正确性,在此基础上逐一分析了摩擦系数、外压大小、螺旋角度等敏感性参数变化以及填充单元对弯曲迟滞性能的影响。研究结果表明,随摩擦系数和外压大小的增大非粘结钢管脐带缆全滑移阶段和滞回阶段弯曲刚度明显增加,而随螺旋角度增加两阶段弯曲刚度则是呈减小趋势。此外,填充单元对两阶段弯曲刚度的影响与摩擦系数的大小有关。 相似文献
9.
带有弹簧支撑的水平板结构,可在波浪作用下起伏运动进行消浪,作为防波堤具有广泛的应用前景,但如何设计支撑刚度仍是当前研究的重点课题。基于黏性流理论建立数值波浪水槽,开展规则波与起伏板防波堤相互作用的模拟,得到起伏板透反射系数随支撑刚度的变化曲线,并分析最小透射系数对应刚度下起伏板运动相位对消浪的影响。为快速得到最小透射系数对应的支撑刚度,根据弹簧—阻尼—质量模型,建立一种以运动相位为输入反推起伏板最优支撑刚度的计算方法,并将推导结果与数值结果进行比较。结果表明,该方法推导的最优支撑刚度值与数值最优值接近,且可省去遍历取最优值的步骤,可为起伏板防波堤的支撑刚度设计提供参考。 相似文献
10.
加肋板是机械产品常用的一种结构形式,其目的是为了加强板结构的刚度特性,以降低结构面的振动响应及抑制结构的辐射噪声。然而,对于肋板结构参数对板结构刚度特征的影响规律,却缺乏深入地研究。本文利用有限元方法,分析研究了肋板的高度、宽度、数量及加肋位置等设计参数对板结构刚度影响的规律性。研究表明:肋板的结构参数与板结构的静、动态刚度呈非线性关系,肋板的高度参数对结构刚度的影响最为显著,纵向肋板在板厚2～4倍高度时对静态刚度的增强效果最大,随着肋板的位置逐渐偏离受载中心,肋板对结构刚度的影响逐渐减小。相关研究结果,对广泛采用板式结构形式的机械产品的结构设计具有一定的参考价值。 相似文献
11.
A stiffened plate is one of the principal structural components of the hull. During the design phase it is useful to study this structure considering it as a system consisting of monodimensional elements. Therefore, it is appropriate to identify the plate breadth that collaborates with the stiffener in the simplified calculation.The aim of this work is to investigate the effective breadth, regarding both stiffness and strength. The analysis is performed comparing various numerical solutions supplied by a finite-element program with solutions based on the beam theory. Analytic expressions and graphs, derived from the results of the parametric investigation, are proposed to design this kind of structure. 相似文献
12.
本文从特征值问题出发 ,结合结构系统的有限单元模型并引入单元损伤因子 ,导出了求解单元损伤因子的方程 ,从而可以确定结构的损伤位置和损伤程度。利用简支梁进行了数值模拟 ,建立了简支梁的有限单元模型 ,用不同单元弹性模量的降低来模拟各种不同的损伤工况 ,并对每种工况进行了损伤位置和损伤程度识别 ,数值模拟结果同实际情况吻合很好。 相似文献
13.
Three-dimensional hydroelasticity theory is used to predict the hydroelastic response of flexible floating interconnected structures. The theory is extended to take into account hinge rigid modes, which are calculated from a numerical analysis of the structure based on the finite element method. The modules and connectors are all considered to be flexible, with variable translational and rotational connector stiffness. As a special case, the response of a two-module interconnected structure with very high connector stiffness is found to compare well to experimental results for an otherwise equivalent continuous structure. This model is used to study the general characteristics of hydroelastic response in flexible floating interconnected structures, including their displacement and bending moments under various conditions. The effects of connector and module stiffness on the hydroelastic response are also studied, to provide information regarding the optimal design of such structures. 相似文献
14.
线弹性土壤中埋设悬跨管道的弯曲和振动特性 总被引：1，自引：0，他引：1
利用细长梁小挠度理论,研究给出了两端埋设在线弹性土壤中的悬跨段管道和埋设段管道在自重作用下的变形和内力公式。基于静挠度公式,用能量法给出了第一阶弯曲振动的固有频率公式。讨论了不同土壤刚度条件下悬跨段管道的变形和内力特征,以及第一阶弯曲振动固有频率,并和工程上推荐使用的简支梁和两端固支梁的静动态特性进行比较。研究表明在跨度大、土壤刚度大、管道弯曲刚度较小时无量纲土壤刚度系数较大,埋设段管道对悬跨段管道的刚度约束比较大,悬跨段管道可以近似按两端固支梁模型来模拟;反之,只有在土壤刚度系数较小的几个参数点上,悬跨管道的静动力特性等价于简支梁模型。 相似文献
15.
The element stiffness matrix of the equivalent beam or pipe element of the deformed leg of the platform is derived by the finite element method. The stresses and displacements of some damaged components are calculated, and the numeri-cal solutions agree well with those obtained by the fine mesh finite element method. Finally, as an application of this method, the stresses of some platform structures are calculated and analyzed. 相似文献
16.
1 .IntroductionOffshoreplatformsarelargescalesteelorconcretestructures.Theyexperiencevariouskindsofdamagessuchasdents ,corrosionpits ,cracks ,deformation ,etc .,afteryearsofenvironmentalimpactofwinds ,waves ,currents ,soilreactions ,earthquakesandice (DuanandLiu ,1 995) .Thesafetyofthestructureshasalwaysbeenthemostimportantissueconcerned ,anditdependsontheassessmentoftheintegrityofthestructures,orspecificallyontheassessmentofthedamagesinthestructures .Riclesetal.( 1 994)experimentallyinvestig… 相似文献
17.
A general theoretical model is developed to investigate the sound radiation from an infinite orthogonally stiffened plate under point excitation force. The plate can be metallic or composite, and fluid loading is also considered in the research. The first order shear deformation theory is used to account for the transverse shear deformation. The motion of the equally spaced stiffeners is examined by considering their bending vibrations and torsional movements. Based on the periodic structure theory and the concepts of the equivalent dynamic flexibility of the plate, the generalized vibro-acoustic equation of the model is obtained by applying the Fourier transform method. The generalized model that can be solved numerically is validated by comparing model predictions with the existing results. Numerical calculations are performed to investigate the effects of the location of the excitation, the spacing of the stiffeners, the plate thickness, the strengthening form and the fiber orientation on the sound radiation characteristic of the orthogonaUy stiffened plate, and some practical conclusions are drawn from these parameter studies. 相似文献
18.
A method for analysis of the structural damage due to ship collisions is developed. The method is based on the idealized structural unit method (ISUM). Longitudinal/transverse webs which connect the outer and the inner hulls are modelled by rectangular plate units. The responses are determined by taking into account yielding, crushing, and rupture. Some plates of the outer and the inner shell subjected to large membrane tensions are modelled by membrane tension triangular/rectangular plate units, while the remaining shell panels are modelled by the usual plate units. The effect of stiffeners on the stiffness and the strength is considered as well. In order to include the coupling effects between local and global failure of the structure, the usual non-linear finite-element technique is applied. In order to deal with the gap and contact conditions between the striking and the struck ships, gap/contact elements are employed. Dynamic effects are considered by inclusion of the influence of strain-rate sensitivity in the material model. On the basis of the theory a computer program has been written. The procedure is verified by a comparison of experimental results obtained from test models of double-skin plated structures in collision/grounding situations with the present solutions. As an illustrative example the procedure has been used for analyses of a side collision of a double-hull tanker. Several factors affecting ship collision response, namely the collision speed and the scantlings/ arrangements of strength members, are discussed. 相似文献