共查询到20条相似文献，搜索用时 46 毫秒
1.
This contribution presents results from a laboratory study investigating the fluid (gas/water) transport properties in the matrix system of the Scandinavian Alum Shale. The maturity of the organic matter of the shale samples ranged between 0.5 and 2.4% vitrinite reflectance (VRr). Gas (He, Ar, CH4) and water flow properties were determined at effective stresses ranging between 5 and 30 MPa and a temperature of 45 °C. The effects of different controlling factors/parameters on the fluid conductivity including permeating fluid, moisture content, anisotropy, heterogeneity, effective stress, pore pressure, and load cycling were analyzed and discussed. Pore volume measurements by helium expansion were conducted under controlled “in situ” effective stress conditions on a limited number of plugs drilled parallel and perpendicular to bedding.For Alum Shale the intrinsic permeability coefficients measured parallel and perpendicular to bedding (6·10−22–8·10−18 m2) were within the range previously reported for other shales and mudstones. Permeability coefficients were strongly dependent on permeating fluid, moisture content, anisotropy, effective stress and other sample-to-sample variations. The intrinsic/absolute permeabilities measured with helium were consistently, higher (up to five times) than those measured with argon and methane. Permeability coefficients (He, CH4) measured on a dry sample were up to six times higher than those measured on an “as-received” sample, depending on effective stress. The effect of moisture on measured permeability coefficients became more significant as effective stress increased. Permeability coefficients (He, CH4) measured parallel to bedding were up to more than one order of magnitude higher than those measured perpendicular to bedding. Parallel to bedding, all samples showed a nonlinear reduction in permeability with increasing effective stress (5–30 MPa). The stress dependence of permeability could be well described by an exponential relationship. 相似文献
2.
Mercury injection capillary pressure (MICP) is a commonly-used technique for measurements of porosity, pore throat size distribution, and injection pressure vs. mercury saturation for many types of rocks. The latter two are correlated to and can be used to estimate permeability. Problems for MICP application in mudrocks are associated with two types of system errors: conformance and compression effects. These two sources of error are well-recognized, but no standard procedures to correct them exist. In this study, a new method for conformance and compression corrections was developed, and the method applied to five Eagle Ford Shale samples. Conformance correction is based on comparison of mercury injection volume vs. pressure curves between epoxy-coated and uncoated samples. Compression correction is based on calculation of compressions before and after mercury intrusion in MICP experiment. Different types of compressions are quantified and compression corrections on porosity, pore throat size distribution, and injection pressure vs. mercury saturation are performed. Porosity and permeability were calculated based on corrected MICP data. Results show that both conformance and compression corrections are important for accurate MICP porosity calculation, whereas conformance correction is more important than compression correction in permeability calculation. 相似文献
3.
X-ray computed tomography and serial block face scanning electron microscopy imaging techniques were used to produce 3D images with a resolution spanning three orders of magnitude from ∼7.7 μm to 7 nm for one typical Bowland Shale sample from Northern England, identified as the largest potential shale gas reservoir in the UK. These images were used to quantitatively assess the size, geometry and connectivity of pores and organic matter. The data revealed four types of porosity: intra-organic pores, organic interface pores, intra- and inter-mineral pores. Pore sizes are bimodal, with peaks at 0.2 μm and 0.04 μm corresponding to pores located at organic–mineral interfaces and within organic matter, respectively. These pore-size distributions were validated by nitrogen adsorption data. The multi-scale imaging of the four pore types shows that there is no connected visible porosity at these scales with equivalent diameter of 20 nm or larger in this sample. However, organic matter and clay minerals are connected and so the meso porosity (<20 nm) within these phases provides possible diffusion transport pathways for gas. This work confirms multi-scale 3D imaging as a powerful quantification method for shale reservoir characterisation allowing the representative volumes of pores, organic and mineral phases to be defined to model shale systems. The absence of connected porosity at scales greater than 20 nm indicates the likely importance of the organic matter network, and associated smaller-scale pores, in controlling hydrocarbon transport. . The application of these techniques to shale gas plays more widely should lead to a greater understanding of properties in the low permeability systems. 相似文献
4.
《Marine and Petroleum Geology》2012,32(1):110-124
The transport properties of Permian to Miocene oil shales (Torbanite, Posidonia, Messel, Himmetoglu, and Condor) were studied using petrophysical and geochemical techniques. The aims of this study were to assess permeability of oil shales, evaluate the evolution of porosity, specific surface area and intergranular permeability during high temperature compaction tests and to verify the suitability of intergranular permeability for petroleum expulsion. Measured permeability coefficients for two samples were 0.72 × 10−21 m² for the Eocene Messel shale and 2.63 × 10−21 m² for the Lower Jurassic Posidonia shale from S. Germany, respectively. BET specific surface areas of the original samples ranged from 0.7 to 10.6 m²/g and decreased after compaction to values from 0.3 to 3.7 m²/g. Initial porosity values ranged from 7.6 to 20.1 % for pre-deformation and from 9.99 to 20.7 % for post-deformation samples. Porosity increased during the high-temperature compaction experiments due to petroleum generation and expulsion. Permeability coefficients estimated using the Kozeny–Carman equation varied from 6.97 × 10−24 m² to 5.22 × 10−21 m² for pre-deformation and from 0.2 × 10−21 m² to 4.8 × 10−21 m² for post-deformation samples reflecting the evolution of their porosity and BET specific surface areas. Measured and calculated permeability were similar for the Messel shale whereas calculated permeability was two orders of magnitude lower for the Posidonia shale from S. Germany. Petroleum expulsion efficiencies under the experimental conditions ranged from 38.6% for the Torbanite to 96.2% for the Posidonia shale from S. Germany. They showed strong positive correlation with the petroleum generation index (R² = 0.91) and poor correlations with porosity (R² = 0.46), average pore throat diameters (R² = 0.22), and compaction (R² = 0.02). Estimated minimum pore-system saturations for petroleum expulsion during the experiments were 12% for the Torbanite and 30% for the Posidonia shale from N. Germany. Pore-system saturation determines whether expulsion occurs mainly through matrix or fracture permeability. For samples with saturation levels above 20%, fracture permeability dominated during the experiments. Evidence based on the measured permeability coefficients, expulsion flow rates, consideration of capillary displacement during generation-related pore invasion and the existence of transport porosity suggests that fracture permeability is the principal avenue of petroleum expulsion from source rocks. This conclusion is supported by microscopic observations. 相似文献
5.
When trying to improve gas productivity from unconventional sources a first aim is to understand gas storage and gas flow potential through the rock by investigating the microstructure, mineralogy and matrix porosity of unfractured shale. The porosity and mineralogy of the Mulgrave Shale member of the Whitby Mudstone Formation (UK) were characterized using a combination of microscopy, X-ray diffraction and gas adsorption methods on samples collected from outcrops. The Whitby Mudstone is an analogue for the Dutch Posidonia Shale which is a possible unconventional source for gas. The Mulgrave shale member of the Whitby Mudstone Formation can microstructurally be subdivided into a fossil rich (>15%) upper half and a sub-mm mineralogically laminated lower half. All clasts are embedded within a fine-grained matrix (all grains < 2 μm) implying that any possible flow of gas will depend on the porosity and the pore network present within this matrix. The visible SEM porosity (pore diameter > 100 nm) is in the order of 0.5–2.5% and shows a non-connected pore network in 2D. Gas adsorption (N2, Ar, He) porosity (pore diameters down to 2 nm) has been measured to be 0.3–7%. Overall more than 40% of the visible porosity is present within the matrix. Comparing the Whitby Mudstone Formation to other (producing) gas shales shows that the rock plots in the low porosity and high clay mineral content range, which could imply that Whitby Mudstone shales could be less favourable to mechanical fracturing than other gas shales. Estimated permeability indicates values in the micro-to nano-darcy range. 相似文献
6.
Shale adsorption and breakthrough pressure are important indicators of shale gas development and key factors in evaluating the reservoir capacities of shales. In this study, geochemical tests, pore-structure tests, methane adsorption tests, and breakthrough-pressure tests were conducted on shales from the Carboniferous Hurleg Formation in eastern Qaidam Basin. The effects of the shale compositions and pore structures on the adsorption and breakthrough pressures were studied, and the reservoir capacities of the shales were evaluated by analyzing the shale adsorptions and sealing effects. The results indicate that the organic carbon content was only one of factors in affecting the adsorption capacity of the shale samples while the effect of the clay minerals was limited. Based on the positive correlation between the adsorption capacity and specific surface area of the shale, the specific surface area of the micropores can be used as an indicator to determine the adsorption capacity of shale. The micro-fracturing of brittle minerals, such as quartz, create a primary path for shale gas breakthrough, whereas the expansion of clay minerals with water greatly increases the breakthrough pressure in the shale samples. Methane adsorption tests showed that maximum methane adsorption for shale samples Z045 and S039 WAS 0.107 and 0.09655 mmol/g, respectively. The breakthrough pressure was 39.36 MPa for sample S039, maintained for 13 days throughout the experiment; however, no breakthrough was observed in sample Z045 when subjected to an injected pressure of 40 MPa for 26 days. This indicates that sample Z045, corresponding to a depth of 846.24 m, exhibited higher adsorption capacity and a better reservoir-sealing effect than sample S039 (498.4 m depth). This study provides useful information for future studies of Qaidam Basin shale gas exploration and development and for evaluation of shale quality. 相似文献
7.
《Marine and Petroleum Geology》2013,39(1):53-72
Evaluation of the reservoir quality of the Triassic Halfway–Montney–Doig hybrid gas shale/tight gas reservoir in the Groundbirch field in northeastern British Colombia requires an integration of unconventional and conventional methodologies. Reservoir evaluation includes reservoir thickness and structure, total porosity, TOC content, organic maturity, pore size distribution (micro- to macro-pore size fractions), surface area, mineralogy and pulse-decay permeability. Quartz (10–74%), carbonate (13–73%) and feldspar (0–42%) dominate the mineralogy of all formations with illite (0–32%) being locally important. The Tmax values range between 443 and 478 °C placing the reservoirs beyond the oil window. Pore size distribution by low-pressure gas adsorption analysis identifies a large variation between the contributions from the micro-, meso- and macro-pore size fractions. Matrix permeabilities range between 1.0E-3 and 6.5E-7 mD at an effective stress between 2400 and 3300 PSI (16.5–22.8 MPa).Changes in depositional environments and diagenetic processes manifest as differences in lithology and mineralogy within the Montney and Doig reservoirs which subsequently affect the fabric, texture and pore size distribution. Fabric, texture and pore size distribution contribute to the variation in the permeability and the proportions of free to sorbed gas within the reservoir. Quartz-rich, coarser-grained intervals (upper portions of Doig C, B and Halfway Formation) have lower surface area, greater porosities and a higher volume of macropores compared to the carbonate- and clay-rich finer-grained intervals (Doig A). Permeabilities do not vary according to lithology with higher permeabilities found within both fine-grained (Doig A) and coarser-grained (Halfway Formation) units. Permeability is controlled by pore size distribution. Higher permeability samples contain a balanced ratio between micro-, meso- and macro-porosity. The finer-grained intervals have higher sorbed gas capacity due to higher surface areas because of the higher volumes of finer mesopores and micropores than the coarser-grained units. However, porosity and permeability are low in some parts of the Doig A and fracture stimulation is necessary to achieve economic flow rates. 相似文献
8.
The pore size classification (micropore <2 nm, mesopore 2–50 nm and macropore >50 nm) of IUPAC (1972) has been commonly used in chemical products and shale gas reservoirs; however, it may be insufficient for shale oil reservoirs. To establish a suitable pore size classification for shale oil reservoirs, the open pore systems of 142 Chinese shales (from Jianghan basin) were studied using mercury intrusion capillary pressure analyses. A quantitative evaluation method for I-micropores (0–25 nm in diameter), II-micropores (25–100 nm), mesopores (100–1000 nm) and macropores (>1000 nm) within shales was established from mercury intrusion curves. This method was verified using fractal geometry theory and argon-ion milling scanning electron microscopy images. Based on the combination of pore size distribution with permeability and average pore radius, six types (I-VI) shale open pore systems were analyzed. Moreover, six types open pore systems were graded as good, medium and poor reservoirs. The controlling factors of pore systems were also investigated according to shale compositions and scanning electron microscopy images. The results show that good reservoirs are composed of shales with type I, II and III pore systems characterized by dominant mesopores (mean 68.12 vol %), a few macropores (mean 7.20 vol %), large porosity (mean 16.83%), an average permeability of 0.823 mD and an average pore radius (ra) of 88 nm. Type IV pore system shales are medium reservoirs, which have a low oil reservoir potential due to the developed II-micropores (mean 57.67 vol %) and a few of mesopores (mean 20.19 vol %). Poor reservoirs (composed of type V and VI pore systems) are inadequate reservoirs for shale oil due to the high percentage of I-micropores (mean 69.16 vol %), which is unfavorable for the flow of oil in shale. Pore size is controlled by shale compositions (including minerals and organic matter), and arrangement and morphology of mineral particles, resulting in the developments of shale pore systems. High content of siliceous mineral and dolomite with regular morphology are advantage for the development of macro- and mesopores, while high content of clay minerals results in a high content of micropores. 相似文献
9.
Shale reservoirs of the Middle and Upper Devonian Horn River Group provide an opportunity to study the influence of rock composition on permeability and pore throat size distribution in high maturity formations. Sedimentological, geochemical and petrophysical analyses reveal relationships between rock composition, pore throat size and matrix permeability.In our sample set, measured matrix permeability ranges between 1.69 and 42.81 nanodarcies and increases with increasing porosity. Total organic carbon (TOC) content positively correlates to permeability and exerts a stronger control on permeability than inorganic composition. A positive correlation between silica content and permeability, and abundant interparticle pores between quartz crystals, suggests that quartz may be another factor enhancing the permeability. Pore throat size distributions are strongly related to TOC content. In organic rich samples, the dominant pore throat size is less than 10 nm, whereas in organic lean samples, pore throat size distribution is dominantly greater than 20 nm. SEM images suggest that in organic rich samples, organic matter pores are the dominant pore type, whereas in quartz rich samples, the dominant type is interparticle pores between quartz grains. In clay rich and carbonate rich samples, the dominant pore type is intraparticle pores, which are fewer and smaller in size.High permeability shales are associated with specific depositional facies. Massive and pyritic mudstones, rich in TOC and quartz, have comparatively high permeability. Laminated mudstone, bioturbated mudstone and carbonate facies, which are relatively enriched in clay or carbonate, have fairly low permeability. 相似文献
10.
As shale oil occurs primarily in micro–nano pores and fractures, research about the effect of pore structure on shale oil accumulation has great significance for shale oil exploration and development. The effect of pore structure on shale oil accumulation in the lower third member of the Shahejie formation (Es3l), Zhanhua Sag, eastern China was investigated using gas adsorption, soxhlet extraction, nuclear magnetic resonance (NMR) analysis, and field emission scanning electron microscope (FE-SEM) observation. The results indicated that the samples contained a larger amount of ink-bottle-shaped and slit-shaped pores after extraction than before extraction. The pore volume and specific surface area of the samples were approximately 2.5 times larger after extraction than before extraction. Residual hydrocarbon occurred primarily in the free-state form in pores with diameters of 10–1000 nm, which can provide sufficient pore volume for free hydrocarbon accumulation. Therefore, pores with diameters of 10–1000 nm were regarded as “oil-enriched pores”, which are effective pores for shale oil exploration, whereas pores with diameters smaller than 10 nm were regarded as “oil-ineffective pores”. Samples with only well-developed small pores with diameters smaller than 1000 nm showed high oil saturation, whereas samples with both small pores and also relatively large pores and micro-fractures presented low oil saturation. As the minimum pore size allowing fluid expulsion is 1000 nm, pores with diameters greater than 1000 nm were considered as “oil-percolated pores”. Large pores and micro-fractures are generally interconnected and may even form a complex fracture mesh, which greatly improves the permeability of shale reservoirs and is beneficial to fluid discharge. 相似文献
11.
Four Haynesville Shale and four Bossier Shale samples were investigated using a combination of Scanning Electron Microscopy (SEM) and Broad Ion Beam (BIB) polishing. This approach enables the microstructure and porosity to be studied down to the mesopore size (<50 nm) in representative areas at the scale of the BIB cross-sections. The samples vary in mineralogy, grain size and TOC and the maturity ranges from 2.42 to 2.58 VRr in the Haynesville Shale to 1.79–2.26 VRr in the Bossier Shale. This variety within the samples enabled us to study controls on the porosity distribution in these shales. Visible pores exist as intraparticle pores mainly in carbonate grains and pyrite framboids and as interparticle pores, mainly in the clay-rich matrix. Pores in organic matter show a characteristic porosity with respect to the type of organic matter, which mainly consists of mixtures of amorphous organic matter and minerals, organic laminae and discrete macerals. A clear positive trend of organic-matter porosity with maturity was found. Pore sizes are power law distributed in the range of 4.4 μm to at least 36 nm in equivalent diameter. The differences in power law exponents suggest that a more grain supported, coarse-grained matrix may prevent pores from mechanical compaction. Porosities measured in the BIB cross-sections were significantly lower in comparison to porosities obtained by Mercury Intrusion Porosimetry (MIP). This difference is mainly attributed to the different resolution achieved with BIB-SEM and MIP and type of pore network. Extrapolation of pore size distributions (PSDs) enables the BIB-SEM porosity to be estimated down to the resolution of the MIP and thus to upscale microstructural observation at the confined space of the BIB-SEM method to bulk porosity measurement. These inferred porosities are in good agreement with the MIP determined porosities, which underpins the assumption that pores segmented in BIB-SEM mosaics are representative of the MIP methodology. 相似文献
12.
Caprock has the most important role in the long term safety of formation gas storage. The caprocks trap fluid accumulated beneath, contribute to lateral migration of this fluid and impede its upward migration. The rapid upward passage of invasive plumes due to buoyancy pressure is prevented by capillary pressure within these seal rocks. In the present study, two main seal rocks, from the Zagros basin in the southwest of Iran, a shale core sample of Asmari formation and an anhydrite core sample of Gachsaran formation, were provided. Absolute permeabilities of shale and anhydrite cores, considering the Klinkenberg effect, were measured as 6.09 × 10−18 and 0.89 × 10−18 m2, respectively. Capillary sealing efficiency of the cores was investigated using gas breakthrough experiments. To do so, two distinct techniques including step by step and residual capillary pressure approaches were performed, using carbon dioxide, nitrogen and methane gases at temperatures of 70 and 90 °C, under confining pressures in the range 24.13–37.92 MPa. In the first technique, it was found that capillary breakthrough pressure of the cores varies in the range from 2.76 to 34.34 MPa. Moreover, the measurements indicated that after capillary breakthrough, gas effective permeabilities lie in range 1.85 × 10−21 – 1.66 × 10−19 m2. In the second technique, the minimum capillary displacement pressure of shale varied from 0.66 to 1.45 MPa with the maximum effective permeability around 7.76 × 10−21 – 6.69 × 10−20 m2. The results indicate that anhydrite caprock of the Gachsaran formation provides proper capillary sealing efficacy, suitable for long term storage of the injected CO2 plumes, due to its higher capillary breakthrough pressure and lower gas effective permeability. 相似文献
13.
Variability in the Lower Bowland shale microstructure is investigated here, for the first time, from the centimetre to the micrometre scale using optical and scanning electron microscopy (OM, SEM), X-Ray Diffraction (XRD) and Total Organic Carbon content (TOC) measurements. A significant range of microtextures, organic-matter particles and fracture styles was observed in rocks of the Lower Bowland shale, together with the underlying Pendleside Limestone and Worston Shale formations encountered the Preese Hall-1 Borehole, Lancashire, UK. Four micro-texture types were identified: unlaminated quartz-rich mudstone; interlaminated quartz- and pyrite-rich mudstone; laminated quartz and pyrite-rich mudstone; and weakly-interlaminated calcite-rich mudstone. Organic matter particles are classified into four types depending on their size, shape and location: multi-micrometre particles with and without macropores: micrometre-size particles in cement and between clay minerals; multi-micrometre layers; and organic matter in large pores. Fractures are categorized into carbonate-sealed fractures; bitumen-bearing fractures; resin-filled fractures; and empty fractures. We propose that during thermal maturation, horizontal bitumen-fractures were formed by overpressuring, stress relaxation, compaction and erosional offloading, whereas vertical bitumen-bearing, resin-filled and empty fractures may have been influenced by weak vertical joints generated during the previous period of veining. For the majority of samples, the high TOC (>2 wt%), low clay content (<20 wt%), high proportion of quartz (>50 wt%) and the presence of a multi-scale fracture network support the increasing interest in the Bowland Shale as a potentially exploitable oil and gas source. The microtextural observations made in this study highlight preliminary evidence of fluid passage or circulation in the Bowland Shale sequence during burial. 相似文献
14.
Mineral types (detrital and authigenic) and organic-matter components of the Ordovician-Silurian Wufeng and Longmaxi Shale (siliceous, silty, argillaceous, and calcareous/dolomitic shales) in the Sichuan Basin, China are used as a case study to understand the control of grain assemblages and organic matter on pores systems, diagenetic pathway, and reservoir quality in fine-grained sedimentary rocks. This study has been achieved using a combination of petrographic, geochemical, and mercury intrusion methods. The results reveal that siliceous shale comprises an abundant amount of diagenetic quartz (40–60% by volume), and authigenic microcrystalline quartz aggregates inhibit compaction and preserve internal primary pores as rigid framework for oil filling during oil window. Although silty shale contains a large number of detrital silt-size grains (30–50% by volume), which is beneficial to preserve interparticle pores, the volumetric contribution of interparticle pores (mainly macropores) is small. Argillaceous shale with abundant extrabasinal clay minerals (>50% by volume) undergoes mechanical and chemical compactions during burial, leading to a near-absence of primary interparticle pores, while pores preserved between clay platelets are dominant with more than 10 nm in pore size. Pore-filling calcite and dolomite precipitated during early diagenesis inhibit later compaction in calcareous/dolomitic shale, but the cementation significantly reduces the primary interparticle pores. Pore-throat size distributions of dolomitic shale show a similar trend with silty shale. Besides argillaceous shale, all of the other lithofacies are dominated by OM pores, which contribute more micropores and mesopores and is positively related to TOC and quartz contents. The relationship between pore-throat size and pore volume shows that most pore volumes are provided by pore throats with diameters <50 nm, with a proportion in the order of siliceous (80.3%) > calcareous/dolomitic (78.4%) > silty (74.9%) > argillaceous (61.3%) shales. In addition, development degree and pore size of OM pores in different diagenetic pathway with the same OM type and maturity show an obvious difference. Therefore, we suggest that the development of OM pores should take OM occurrence into account, which is related to physical interaction between OM and inorganic minerals during burial diagenesis. Migrated OM in siliceous shale with its large connected networks is beneficial for forming more and larger pores during gas window. The result of the present work implies that the study of mineral types (detrital and authigenic) and organic matter-pores are better understanding the reservoir quality in fine-grained sedimentary rocks. 相似文献
15.
The estimation of the sealing capability of cap rocks dynamically is one of the fundamental geological problems that must be resolved in petroleum exploration. In this paper, a porosity–capillary pressure (ϕ–Pc) method was used to estimate the sealing capacity during cap rock burial and a permeability–capillary pressure (K–Pc) plus over-consolidation ratio (OCR) method to estimate the sealing capacity during uplift. Based on 120 capillary pressure–porosity measurements, a ϕ–Pc mathematical model has been established for the burial phase. By analyzing the permeability data measured from 12 mudstone/shale samples from different stratigraphic intervals under step loading conditions, a permeability–confining pressure (K–P) mathematical model has been constructed. Moreover, capillary pressure–permeability data measured from 141 mudstone or shale cap rocks have been used to establish a K–Pc mathematical model for seal capacity evaluation during uplift. Additionally, the OCR of mudstone or shale was calculated from the results of reconstructed burial and uplift histories. These mathematical models were used in case studies in the Sichuan Basin, South China. The results indicate that capillary pressure (Pc) is inadequate in evaluating sealing capacity of cap rocks but the combination of parameters Pc and OCR works well. The agreement between calculated and measured values shows the effectiveness and reliability of the models for dynamic estimation of the sealing capacity of mudstone/shale cap rocks established in this study. 相似文献
16.
Organic shales deposited in a continental environment are well developed in the Ordos Basin, NW China, which is rich in hydrocarbons. However, previous research concerning shales has predominantly focused on marine shales and barely on continental shales. In this study, geochemical and mineralogical analyses, high-pressure mercury intrusion and low-pressure adsorption were performed on 18 continental shale samples obtained from a currently active shale gas play, the Chang 7 member of Yanchang Formation in the Ordos Basin. A comparison of all these techniques is provided for characterizing the complex pore structure of continental shales.Geochemical analysis reveals total organic carbon (TOC) values ranging from 0.47% to 11.44%, indicating that there is abundant organic matter (OM) in the study area. Kerogen analysis shows vitrinite reflectance (Ro) of 0.68%–1.02%, indicating that kerogen is at a mature oil generation stage. X-ray diffraction mineralogy (XRD) analysis indicates that the dominant mineral constituents of shale samples are clay minerals (which mainly consist of illite, chlorite, kaolinite, and negligible amounts of montmorillonite), quartz and feldspar, followed by low carbonate content. All-scale pore size analysis indicates that the pore size distribution (PSD) of shale pores is mainly from 0.3 to 60 nm. Note that accuracy of all-scale PSD analysis decreases for pores less than 0.3 nm and more than 10 μm. Experimental analysis indicates that mesopores (2–50 nm) are dominant in continental shales, followed by micropores (<2 nm) and macropores (50 nm–10 μm). Mesopores have the largest contribution to pore volume (PV) and specific surface area (SSA). In addition, plate- and sheet-shaped pores are dominant with poor connectivity, followed by hybrid pores. Results of research on factors controlling pore structure development show that it is principally controlled by clay mineral contents and Ro, and this is different from marine systems. This study has important significance in gaining a comprehensive understanding of continental shale pore structure and the shale gas storage–seepage mechanism. 相似文献
17.
Shale samples collected from seven wells in the southeastern Ordos Basin were tested to investigate quantitatively the pore structure and fractal characteristics of the Lower Permian Shanxi Shale, which was deposited in a marine-continental transitional (hereinafter referred to as the transitional) environment. Low-pressure nitrogen adsorption data show that the Shanxi Shale exhibits considerably much lower surface area (SA) and pore volume (PV) in the range of 0.6–1.3 m2/g and 0.25–0.9 ml/100 g, respectively. Type III kerogen abundant in the transitional Shanxi Shale were observed to be poorly developed in the organic pores in spite of being highly mature, which resulted in a small contribution of organic matter (OM) to the SA and PV. Instead, I/S (illite-smectite mixed clay) together with illite jointly contributed mostly to the SA and PV as a result of the large amount of inter-layer pores associated with them, which were evident in broad-ion-beam (BIB) imaging and statistical analysis. Additionally, the Shanxi Shale has fractal geometries of both pore surface and pore structure, with the pore surface fractal dimension (D1) ranging from 2.16 to 2.42 and the pore structure fractal dimension (D2) ranging from 2.49 to 2.68, respectively. The D1 values denote a pore surface irregularity increase with an increase in I/S and illite content attributed to their more irregular pore surface compared with other mineralogical compositions and OM. The fractal dimension D2 characterizing the pore structure complexity is closely related to the pore arrangement and connectivity, and I/S and illite decrease the D2 when their contents increase due to the incremental ordering degree and connectivity of I/S- or illite-hosted pores. Meanwhile, other shale constituents (including kaolinite, chlorite, and OM) that possess few pores can significantly increase the pore structure complexity by way of pore-blocking. 相似文献
18.
Thirty-six Silurian core and cuttings samples and 10 crude oil samples from Ordovician reservoirs in the NC115 Concession, Murzuq Basin, southwest Libya were studied by organic geochemical methods to determine source rock organic facies, conditions of deposition, thermal maturity and genetic relationships. The Lower Silurian Hot Shale at the base of the Tanezzuft Formation is a high-quality oil/gas-prone source rock that is currently within the early oil maturity window. The overall average TOC content of the Hot Shale is 7.2 wt% with a maximum recorded value of 20.9 wt%. By contrast, the overlying deposits of the Tanezzuft Formation have an average TOC of 0.6 wt% and a maximum value of 1.1 wt%. The organic matter in the Hot Shale consists predominantly of mixed algal and terrigenous Type-II/III kerogen, whereas the rest of the formation is dominated by terrigenous Type-III organic matter with some Type II/III kerogen. Oils from the A-, B- and H-oil fields in the NC115 Concession were almost certainly derived from marine shale source rocks that contained mixed algal and terrigenous organic input reflecting deposition under suboxic to anoxic conditions. The oils are light and sweet, and despite being similar, were almost certainly derived from different facies and maturation levels within mature source rocks. The B-oils were generated from slightly less mature source rocks than the others. Based on hierarchical cluster analysis (HCA), principal component analysis (PCA), selected source-related biomarkers and stable carbon isotope ratios, the NC115 oils can be divided into two genetic families: Family-I oils from Ordovician Mamuniyat reservoirs were probably derived from older Palaeozoic source rocks, whereas Family-II oils from Ordovician Mamuniyat–Hawaz reservoirs were probably charged from a younger Palaeozoic source of relatively high maturity. A third family appears to be a mixture of the two, but is most similar to Family-II oils. These oil families were derived from one proven mature source rock, the Early Silurian, Rhuddanian Hot Shale. There is a good correlation between the Family-II and -III oils and the Hot Shale based on carbon isotope compositions. Saturated and aromatic maturity parameters indicate that these oils were generated from a source rock of considerably higher maturity than the examined rock samples. The results imply that the oils originated from more mature source rocks outside the NC115 Concession and migrated to their current positions after generation. 相似文献
19.
The trace and rare earth elements (REE) analyses were conducted on samples collected from a 30 m core of the Marcellus Shale obtained from Greene County, southwestern Pennsylvania. Our results suggest that organic matter enrichment trends in the Marcellus Shale can be directly linked with the Acadian Orogeny. The Acadian Orogeny has been recognized as a main sediment source for the Marcellus Shale. Synthesis of tectonic history and recent ash bed geochronology, reveals that deposition of the organic carbon-rich (OR) zone (characterized by TOC >4%; located between 2393 m and 2406.5 m core depth) in the studied Marcellus Shale core was coincident with tectonically active and magmatic quiescent period of the Acadian orogeny (ca. 395–380 Ma). This time period also corresponds to the highest rate of mountain building in the Acadian Orogeny. The light rare earth (LREE) and selected trace elemental (e.g., Ta, Cs) composition of the OR zone sediments is similar to that of the bulk continental crust, supporting the lack of magmatic activity in the source area (i.e. Acadian Orogeny). In contrast, subsequent deposition of the organic carbon-poor (OP) sediments (characterized by TOC <4%; located between 2376 m and 2393 m core depth) in the upper Marcellus Shale occurred synchronously with a magmatic active phase (ca. 380–370 Ma) during the Acadian orogeny. The OP zone sediments have LREE and trace elemental composition similar to the average of the upper continental crust, suggesting intrusion of granodiorite rocks during a magmatic active period of Acadian Orogeny. The temporal and geochemical correlation between the Acadian orogenesis and the Marcellus deposition provide evidence for the role of tectonism in the enrichment of organic matter in the Marcellus Shale. 相似文献
20.
The Upper Jurassic marlstones (Mikulov Fm.) and marly limestones (Falkenstein Fm.) are the main source rocks for conventional hydrocarbons in the Vienna Basin in Austria. In addition, the Mikulov Formation has been considered a potential shale gas play. In this paper, organic geochemical, petrographical and mineralogical data from both formations in borehole Staatz 1 are used to determine the source potential and its vertical variability. Additional samples from other boreholes are used to evaluate lateral trends. Deltaic sediments (Lower Quarzarenite Member) and prodelta shales (Lower Shale Member) of the Middle Jurassic Gresten Formation have been discussed as secondary sources for hydrocarbons in the Vienna Basin area and are therefore included in the present study.The Falkenstein and Mikulov formations in Staatz 1 contain up to 2.5 wt%TOC. The organic matter is dominated by algal material. Nevertheless, HI values are relative low (<400 mgHC/gTOC), a result of organic matter degradation in a dysoxic environment. Both formations hold a fair to good petroleum potential. Because of its great thickness (∼1500 m), the source potential index of the Upper Jurrasic interval is high (7.5 tHC/m2). Within the oil window, the Falkenstein and Mikulov formations will produce paraffinic-naphtenic-aromatic low wax oil with low sulfur content. Whereas vertical variations are minor, limited data from the deep overmature samples suggest that original TOC contents may have increased basinwards. Based on TOC contents (typically <2.0 wt%) and the very deep position of the maturity cut-off values for shale oil/gas production (∼4000 and 5000 m, respectively), the potential for economic recovery of unconventional petroleum is limited. The Lower Quarzarenite Member of the Middle Jurassic Gresten Formation hosts a moderate oil potential, while the Lower Shale Member is are poor source rock. 相似文献