共查询到20条相似文献，搜索用时 62 毫秒
1.
In this paper results of triaxial and true triaxial testing conducted on physical models of a rock mass are used to describe its post failure behaviour. The specimens comprised of three continuous joint sets and were prepared from blocks of sand lime model material. The testing was performed using a True Triaxial System (TTS) developed by the authors. The results show strain hardening, strain softening and plastic behaviour in the simulated rock mass specimens depending upon joint geometry and stress state. Expressions are suggested to estimate post peak modulus in triaxial and true triaxial stress conditions. Finally, a zonation table is proposed to assess the strain hardening, softening and plasticity behaviour of a rock mass material with the help of joint geometry and confining stress conditions at site. 相似文献
2.
3.
4.
The present work proposes an approach to adapt existing isotropic models to transversely isotropic materials. The main idea is to introduce equivalence relations between the real material and a fictitious isotropic one on which one can take all the advantages of the well‐established isotropic theory. Two applications of this approach are presented here: a failure criterion and a damage model that takes into account the load‐induced anisotropy. In both cases, theoretical predictions are in agreement with the experimental data. In the present paper, the developed approach is applied to sedimentary rock materials; nevertheless, it can be generalized to any material that exhibits transverse isotropy. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
5.
F. Molenkamp 《国际地质力学数值与分析法杂志》1988,12(5):467-475
A simple isotropic nonlinear elastic model has been developed to describe the behaviour of granular materials immediately after stress reversal. Its three parameters can be measured in the same drained triaxial test. 相似文献
6.
In this paper, an existing elastoplastic constitutive model, originally developed for granular soils, is adapted to describe the stress–strain behaviour of cemented granular soils. The existing model (CJS), due to its modular formulation, can be easily developed to take into account different supplementary behavioural aspects in soil mechanics. In the present study, the failure mechanism of the CJS model is modified by introducing the essential aspects in the behaviour of cemented granular soils in its formulation. All of the model parameters have clear physical meaning and can be identified using classical laboratory tests. A set of direct relations between model parameters and famous mechanical parameters of soils such as internal friction angle and cohesion at peak and residual states is presented. In order to validate the model, the results of triaxial and uniaxial tests in the compression and extension performed on cemented granular materials are used. The validation results indicate the good capability of the proposed model. 相似文献
7.
剪胀角是描述岩石体积膨胀扩容的常用参数,在非关联流动法则中,连续介质理论通常假设剪胀角为0;在关联流动法则中,其值恒定且等于内摩擦角。岩石三轴压缩全过程体应变曲线表明,其体积剪胀性依赖于围压和塑性参量,破坏过程中不仅其特征强度随围压和塑性参量呈非线性变化,而且剪胀特性也表现出非线性特征。基于塑性力学理论,针对锦屏大理岩损伤控制的全过程三轴加、卸载试验,采用双参数非线性函数拟合方法建立了能同时考虑围压效应和塑性参量的非线性剪胀角模型。结果表明,对于大理岩、中硬岩,在破坏过程中扩容行为强烈依赖围压和岩石塑性参量,均表现出先快速增加至峰值后,随着塑性变形增加逐渐减小的非线性演化规律。提出的双参数非线性剪胀角模型很好地描述了岩石破坏过程中的体积扩容特性,其结果对于研究地下工程围岩应力变化诱发的围岩剪胀破坏机制、体积扩容膨胀区范围预测和围岩支护的合理设计均具有一定的理论和工程应用价值。 相似文献
8.
A review of the literature indicates that the elastic behaviour of granular materials is isotropic and that Poissony's ratio is constant, whereas Young's Modulus, the bulk modulus and the shear modulus vary with the mean normal stress and the deviatoric stress. A nonlinear, isotropic model for the elastic behaviour is developed on the basis of theoretical considerations involving the principle of conservation of energy. Energy is therefore neither generated not dissipated in closed-loop stress paths or in closed-loop strain paths. The framework for the model consists of Hooke's law, in which Poission's ratio is constant and Young's modulus is expressed as a power function invlving the first invariat of the stress tensor and the second invariant of the deviatoric stress tensor. The characteristics of the model are described, and the accuracy is evaluated by comparison with experimental results from triaxial tests and three-dimensional cubical triaxial tests with a variety of stress paths. Parameter determination from unloading–reloading cycles in conventional triaxial compression tests is demonstrated, typical parameter values are given for granular materials and extension of the model to soils with effective cohesion is described. 相似文献
9.
For numerical studies of geotechnical structures under earthquake loading, aiming to examine a possible failure due to liquefaction, using a sophisticated constitutive model for the soil is indispensable. Such a model must adequately describe the material response to a cyclic loading under constant volume (undrained) conditions, amongst others the relaxation of effective stress (pore pressure accumulation) or the effective stress loops repeatedly passed through after a sufficiently large number of cycles (cyclic mobility, stress attractors). The soil behaviour under undrained cyclic loading is manifold, depending on the initial conditions (e.g. density, fabric, effective mean pressure, stress ratio) and the load characteristics (e.g. amplitude of the cycles, application of stress or strain cycles). In order to develop, calibrate and verify a constitutive model with focus to undrained cyclic loading, the data from high-quality laboratory tests comprising a variety of initial conditions and load characteristics are necessary. The purpose of these two companion papers was to provide such database collected for a fine sand. The database consists of numerous undrained cyclic triaxial tests with stress or strain cycles applied to samples consolidated isotropically or anisotropically. Monotonic triaxial tests with drained or undrained conditions have also been performed. Furthermore, drained triaxial, oedometric or isotropic compression tests with several un- and reloading cycles are presented. Part I concentrates on the triaxial tests with monotonic loading or stress cycles. All test data presented herein will be available from the homepage of the first author. As an example of the examination of an existing constitutive model, the experimental data are compared to element test simulations using hypoplasticity with intergranular strain. 相似文献
10.
水合物含量、有效围压是影响含天然气水合物沉积物力学性质的主要因素,在忽略其他次要因素（包括水合物种类、试样颗粒大小、试验条件等）的情况下,水合物含量和有效围压是决定试样弹性模量的两个关键参数。在分析等效弹性模量与水合物含量相互关系的基础上,考虑有效围压的影响,建立了弹性模量与有效围压的幂函数关系;同时采用Drucker-Prager破坏准则来表示含天然气水合物沉积物微元强度,并假设其微元强度服从Weibull分布,从而建立了含天然气水合物沉积物的损伤统计本构模型,与不同有效围压下的试验结果及已有研究成果相比较,表明了所建模型能够很好地模拟三轴剪切条件下含水合物沉积物试样的应力-应变关系特性。此研究成果可对含天然气水合物沉积物工程性状的数值模拟提供参考。 相似文献
11.
12.
P. S. Theocaris 《Rock Mechanics and Rock Engineering》1999,32(4):267-290
Summary Experimental evidence from true triaxial tests on dense rocks are analysed with emphasis on the failure modes of these materials
under multiaxial loading, ambient temperature and external pressure. The strong dependence of the modes of fracture on the
secondary components of applied stresses, and especially on the intermediate principal stress, indicated that the failure
surface of these brittle materials may be appropriately described by a failure tensor polynomial criterion. As such, the elliptic
paraboloid failure criterion was found to conveniently describe their mode of failure, by considering also the severe influence
of anisotropy of the material.
For this purpose, a method developed recently (Theocaris and Panagiotopoulos, 1995a, 1995b) was applied, defining anisotropic
hardening plasticity through an appropriate sequence of anisotropic elasticity problems. Assuming a particular path of loading
or unloading, we measured the instantaneous tension and compression yield stresses along the transient principal-stress directions.
These parameters completely define the instantaneous state of anisotropy of the body for the corresponding loading step, by
applying the theory of the elliptic paraboloid failure locus (EPFS) (Theocaris, 1989a). A parameter identification problem was formulated on the constitutive expressions for this most general failure criterion. Then, by applying convenient constraints
derived from the EPFS theory, which serve as filters throughout the whole procedure, the characteristic values of terms defining
the variable components of the failure tensor polynomial were calculated, as the material was continuously loaded from the
elastic into the plastic region and up to the ultimate failure load. Accurate simple tests in uniaxial tension and compression
provided sufficient data for the definition of the yield loci of the material, at the considered loading step. These tests
may be complemented with biaxial and triaxial modes of loading of the specimens. The results improve the accuracy and sensitivity
of the method. All such data were used as input values, for establishing the mode of plastic deformation of the body during
particular loading paths.
Moreover, the method employed allows the complete definition of the components of the failure, H, and the strength differential effect, h, tensors at each loading step. These quantities define completely the failure tensor polynomial for each material. Therefore,
it presents the important advantage over other experimental methods by clearly indicating the parts contributed to the failure
mode (either by plasticity, or by the strength differential effect) and their evolution during plastic deformation.
As convenient prototype materials for testing the method, specimens of metamorphic rocks such as Westerly granite (G), or
quartzite (Q) were selected. Interesting results concerning the mechanical and especially the failure modes of such materials
were obtained. Furthermore, the mechanical tests indicated clearly some basic properties of these materials as concerns the
mode of their structure. 相似文献
13.
Summary This paper is intended to describe the SHELVIP (Stress Hardening ELastic VIscous Plastic) model, a new viscoplastic constitutive
law which has been developed to incorporate the most important features of behaviour observed in tunnels excavated in severe
to very severe squeezing conditions. This model couples the elastoplastic and time-dependent behaviour by using a plastic
yield surface, as frequently adopted in tunnel design analysis, and the definition of a state of overstress referred to a
viscoplastic yield surface. The model is formulated in all its detailed aspects. The related analytical closed-form solution
for representing triaxial creep deformations is developed. Also developed is an incremental numerical solution for describing
the triaxial stress–strain behaviour under constant strain rate conditions. The model is shown to fit very satisfactorily
the results of creep tests on clay shales and relaxation tests on coal specimens, as recently performed for design analysis
of tunnels in squeezing conditions.
Correspondence: D. Debernardi, Department of Structural and Geotechnical Engineering, Politecnico di Torino, Torino, Italy 相似文献
14.
N. P. Honkanadavar Nripendra Kumar Murari Ratnam 《Geotechnical and Geological Engineering》2014,32(4):1001-1015
Two types of modeled rockfill materials were collected from Renuka dam site, Himachal Pradesh, India and Salma dam site, Afghanistan. The rockfill material collected from Renuka dam site is rounded to sub-rounded in shape and the rockfill material collected from Salma dam site is angular to sub-angular in shape. The prototype gradation rockfill material consists maximum particle size larger than 1,000 mm. Therefore, for carrying out laboratory testing and modeling the bahaviour, the prototype rockfill material is scaled down to the maximum particle size (dmax) of 25, 50 and 80 mm for both projects material using parallel gradation technique. Triaxial compression and Index properties tests were conducted on both project rockfill materials and are presented. From the triaxial behaviour, it is observed that the stress–strain behaviour is non-linear, inelastic and stress dependent for both the materials. The material compresses during the initial shearing and shows dilation effect with further shearing. It is observed that the ?-value for alluvial rockfill material increases with increase in dmax and reverse trend is observed for blasted quarried rockfill material which shows the importance of the type of material. The stress–strain-volume change behaviour of both projects modeled rockfill material was predicted by using hierarchical single surface (HISS) model based on elasto plasticity and compared with the laboratory test results. From the comparison, it is observed that both results match closely. It is, therefore, suggested that the behaviour of both types of rockfill materials can be characterized successfully using HISS model. 相似文献
15.
When impact loaded, concrete is submitted to high triaxial stresses. The experimental response of concrete under quasi‐static triaxial compression is studied using a triaxial press capable of applying a mean pressure greater than 1 GPa on cylindrical samples measuring 7 cm in diameter and 14 cm high. A numerical analysis of these previous experiments is performed herein at a mesoscopic scale. Concrete is modelled as a biphasic material consisting of a mortar (cement paste and fine aggregates) and roughly spherical aggregates (with a diameter exceeding 2 mm) whose characteristics are applied on a regular cubic finite element mesh. A damage‐plasticity model is then used to model the behaviour of mortar. An identification of model parameters on mortar samples and the subsequent comparison between numerical and experimental tests will be presented for hydrostatic and triaxial compression. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
16.
考虑颗粒破碎的粗粒土剪胀性统一本构模型 总被引：2，自引：0，他引：2
粗粒土作为无黏性散粒状材料具有状态依赖特性,土体的剪切特性受密度和应力水平影响。易破碎是粗粒土的另一个特点,颗粒破碎影响粗粒土的剪胀、内摩擦角、峰值强度和渗透系数。为了能够准确地描述粗粒土的应力-应变关系,采用初始状态参量描述粗粒土的内部状态,根据三轴试验数据建立考虑颗粒破碎耗能的应力-应变关系,采用相关联流动法则推导考虑颗粒破碎的粗粒土剪胀性“统一本构模型”,并建立初始状态参量与模型参数之间的关系。所建立的统一本构模型既考虑了颗粒破碎对剪胀、内摩擦角的影响,又考虑了剪切特性对土体初始状态的依赖。采用变异粒子群算法拟合试验曲线,确定模型参数。模型计算结果能够很好地拟合试验曲线。采用同一组参数对假定的初始状态进行模拟计算,计算结果表明,模型能够模拟不同初始密度和应力水平下粗粒土变形的一般规律。 相似文献
17.
Characterisation of confinement effect on jointed rock pillars using a Synthetic Rock Mass approach 
下载免费PDF全文
下载免费PDF全文 Confinement effect on jointed rock pillars is numerically characterised in this research using a Synthetic Rock Mass (SRM) approach. The SRM is an integrated model incorporating a discrete fracture network within a Particle Flow Code 3D particle assembly. In this paper, the confinement effect on a 3D jointed pillar SRM model is investigated in a series of simulations, including biaxial compression tests and true and conventional triaxial compression tests. The numerical results suggest that the applied confining stresses generally result in higher pillar strengths and ductile post‐peak responses. More brittle post‐peak behaviour is simulated in the biaxial and true triaxial tests when the pillar is confined by a high stress in one lateral direction and by a zero/low stress in the other lateral direction. This phenomenon is attributed to significant lateral pillar dilation in the less confined direction. Detailed pillar failure modes are monitored in the uniaxial and triaxial tests. Axial splitting fractures and long shear zones cutting through the pillar are simulated when the pillar is able to dilate in the direction of least confinement. Localised shearing along joints and failed rock blocks is the dominant failure mode when the pillar dilation is resisted by the applied confining stresses. The pillar remains relatively intact with limited cracking in the pillar core in the highly confined triaxial tests. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
18.
This paper presents a three‐dimensional elastoplastic constitutive model for predicting the hydraulic and mechanical behaviour of unsaturated soils. It is based on experimental results obtained from a series of controlled‐suction triaxial tests on unsaturated compacted clay with different initial densities. Hydraulic hysteresis in the water‐retention behaviour is modelled as an elastoplastic process, with the elastic part modelled by a series of scanning curves and the elastoplastic part modelled by the main drying and wetting curves. The effect of void ratio on the water‐retention behaviour is studied using data obtained from controlled‐suction wetting–drying cyclic tests on unsaturated compacted clay with different initial densities. The effect of the degree of saturation on the stress–strain‐strength behaviour and the effect of void ratio on the water‐retention behaviour are considered in the model, as is the effect of suction on the hydraulic and mechanical behaviour. The initial density dependency of the compacted soil behaviour is modelled by experimental relationships between the initial density and the corresponding yield stress and, thereby, between the initial density and the normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure and yield surfaces in the deviatoric stress plane are given by the Matsuoka–Nakai criterion. Model predictions of the stress–strain and water‐retention behaviour are compared with those obtained from triaxial tests with different initial densities under isotropic compression, triaxial compression and triaxial extension, with or without variation in suction. The comparisons indicate that the model accurately predicts the hydraulic and mechanical behaviour of unsaturated compacted soils with different initial densities using the same material constant. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
19.
沉积岩的一种各向异性模型 总被引：1，自引：0，他引：1
给出了沉积岩的一种各向异性模型。用一个各向异性参数描述这类材料的固有各向异性，各向异性参数和单轴抗压强度是一个分布函数，其分布用一个微结构张量和加载方向表示。建立了一个描述各向异性沉积岩变形过程的全塑性模型。用该模型对这一些三轴试验进行了模拟，结果表明该模型能有效地描述沉积岩的固有各向异性。 相似文献
20.
The physical properties of bentonite-based buffer materials for nuclear waste repositories have been investigated by a number of different laboratory tests. These tests have yielded a material model that is valid for conditions close to water saturation and is useful for describing: (a) the stress, strain and volume change behaviour; (b) the pore pressure and flow of water; and (c) the thermal and thermomechanical response.
The material model is based on the Drucker-Prager Plasticity model and a Porous Elastic Model. The effective stress concept and Darcy's law are applied and the swelling/consolidation and thermomechanical processes are coupled according to the separate mechanical properties of the pore water, the solids and the clay skeleton. The model can be used by the finite-element program ABAQUS.
The model has been tested in several laboratory and field verification tests. Comparison between measured and calculated behaviour shows that the general behaviour is described properly and several calculations of different scenarios have been made for the Swedish KBS 3 concept. However, certain processes, like the hysteresis effect at consolidation/swelling, the curved stress-strain relation at shearing, and the curved failure envelope, are not modelled in a perfectly accurate way and an improved material model is proposed here. It combines the behaviour of the Cam-clay model on the wet side with the more relevant plastic behaviour of a modified Drucker-Prager model with a curved failure envelope and the possibility to introduce strain softening after failure.
The paper presents some laboratory results that are the basis of the first model. It also shows the application of the model to finite-element calculations of some laboratory tests. Comparisons between the calculations and measured results expose some disadvantages of the model and a concept for an improved model is suggested. 相似文献