首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Comparison of the chemical characteristics of spring and river water draining the flanks of Poa´s Volcano, Costa Rica indicates that acid chloride sulfate springs of the northwestern flank of the volcano are derived by leakage and mixing of acid brines formed in the summit hydrothermal system with dilute flank groundwater. Acid chloride sulfate waters of the Rio Agrio drainage basin on the northwestern flank are the only waters on Poa´s that are affected by leakage of acid brines from the summit hydrothermal system. Acid sulfate waters found on the northwestern flank are produced by the interaction of surface and shallow groundwater with dry and wet acid deposition of SO2 and H2SO4 aerosols, respectively. The acid deposition is caused by a plume of acid gases that is released by a shallow magma body located beneath the active crater of Poa´s.No evidence for a deep reservoir of neutral pH sodium chloride brine is found at Poa´s. The lack of discharge of sodium chloride waters at Poa´s is attributed to two factors: (1) the presence of a relatively volatile-rich magma body degassing at shallow depths (< 1 km) into a high level summit groundwater system; and (2) the hydrologic structure of the volcano in which high rates of recharge combine with rapid lateral flow of shallow groundwater to prevent deep-seated sodium chloride fluids from ascending to the surface. The shallow depth of the volatile-rich magma results in the degassing of large quantities of SO2 and HCl. These gases are readily hydrolyzed and quickly mix with meteoric water to form a reservoir of acid chloride-sulfate brine in the summit hydrothermal system. High recharge rates and steep hydraulic gradients associated with elevated topographic features of the summit region promote lateral flow of acid brines generated in the summit hydrothermal system. However, the same high recharge rates and steep hydraulic gradients prevent lateral flow of deep-seated fluids, thereby masking the presence of any sodium chloride brines that may exist in deeper parts of the volcanic edifice.Structural, stratigraphic, and topographic features of Poa´s Volcano are critical in restricting flow of acid brines to the northwestern flank of the volcano. A permeable lava-lahar sequence that outcrops in the Rio Agrio drainage basin forms a hydraulic conduit between the crater lake and acid chloride sulfate springs. Spring water residence times are estimated from tritium data and indicate that flow of acid brines from the active crater to the Rio Agrio source springs is relatively rapid (3 to 17 years). Hydraulic conductivity values of the lava-lahar sequence calculated from residence time estimates range from 10−5 to 10−7 m/s. These values are consistent with hydraulic conductivity values determined by aquifer tests of fractured and porous lava/pyroclastic sequences at the base of the northwestern flank of the volcano.Fluxes of dissolved rock-forming elements in Rio Agrio indicate that approximately 4300 and 1650 m3 of rock are removed annually from the northwest flank aquifer and the active crater hydrothermal system, respectively. Over the lifetime of the hydrothermal system (100's to 1000's of years), significant increases in aquifer porosity and permeability should occur, in marked contrast to the reduction in permeability that often accompanies hydrothermal alteration in less acidic systems. Average fluxes of fluoride, chloride and sulfur calculated from discharge and compositional data collected in the Rio Agrio drainage basin over the period 1988–1990 are approximately 2, 38 and 30 metric tons/day. These fluxes should be representative of minimum volatile release rates at Poa´s in the last 10 to 20 years.  相似文献   

2.
Thermal waters of the Ömer–Gecek geothermal field, Turkey, with temperatures ranging from 32 to 92°C vary in chemical composition and TDS contents. They are generally enriched in Na–Cl–HCO3 and suggest deep water circulation. Silica and cation geothermometers applied to the Ömer–Gecek thermal waters yield reservoir temperatures of 75–155°C. The enthalpy–chloride mixing model, which approximates a reservoir temperature of 125°C for the Ömer–Gecek field, accounts for the diversity in the chemical composition and temperature of the waters by a combination of processes including boiling and conductive cooling of deep thermal water and mixing of the deep thermal water with cold water. It is also determined that the solubility of silica in most of the waters is controlled by the chalcedony phase. Equilibrium states of the Ömer–Gecek thermal waters studied by means of the Na–K–Mg triangular diagram, Na–K–Mg–Ca diagram, K–Mg–Ca geoindicator diagram, activity diagrams in the systems composed of Na2O–CaO–K2O–Al2O3–SiO2–CO2–H2O phases, log SI diagrams, and finally the alteration mineralogy indicate that most of the spring and low-temperature well waters in the area can be classified as shallow or mixed waters which are likely to be equilibrated with calcite, chalcedony and kaolinite at predicted temperature ranges similar to those calculated from the chemical geothermometers. It was also observed that mineral equilibrium in the Ömer–Gecek waters is largely controlled by CO2 concentrations.  相似文献   

3.
This paper examines groundwater hydrochemical characteristics during mixing between thermal and non-thermal groundwater in low-to-medium temperature geothermal fields. A case study is made of Daying and Qicun geothermal fields in the Xinzhou basin of Shanxi province, China. The two geothermal fields have similar flow patterns, with recharge sourced from precipitation in mountain areas heated through a deep cycle, before flowing into overlying Quaternary porous aquifers via fractures. Hydrochemical features of 60 ground- and surface water samples were examined in the context of hydrogeologic information. The average temperatures of the deep geothermal reservoirs are estimated to be 125 °C in Daying field, and 159 °C in Qicun field, based on Na–K–Mg geothermometry, while slightly lower estimates are obtained using silica geothermometers. Hydrochemical features of thermal water are distinct from cold water. Thermal groundwater is mainly Cl·SO4–Na type, with high TDS, while non-thermal groundwater is mostly HCO3–Ca·Mg and HCO3–Ca type in the Daying and Qicun regions, respectively. Hydrogeochemical processes are characterized by analyzing ion ratios in various waters. Higher contents of some minor elements in thermal waters, such as F, Si, B and Sr, are probably derived from extended water–rock interaction, and these elements can be regarded as indicators of flow paths and residence times. Mixing ratios between cold and thermal waters were estimated with Cl, Na, and B concentrations, using a mass balance approach. Mixing between ascending thermal waters and overlying cold waters is extensive. The proportion of water in the Quaternary aquifer derived from a deep thermal source is lower in Daying geothermal field than in Qicun field (5.3–7.3% vs. 6.3–49.3%). Mixing between thermal and non-thermal groundwater has been accelerated by groundwater exploitation practices and is enhanced near faults. Shallow groundwater composition has also been affected by irrigation with low-temperature thermal water.  相似文献   

4.
The occurrence of submarine groundwater discharge (SGD) as well as its supply of many nutrients and metals to coastal seawaters is now generally known. However, previous studies have focused on the chemical and radiological analysis of groundwater, surface seawater, shallow marine sediments and their pore waters, as well as the measurement of upward flow through the marine sediments, as end members of the discharge process. In this study, chemical and isotopic analysis results of marine subsurface waters are reported. These were obtained from deep boreholes of an undersea liquefied petroleum gas (LPG) storage cavern, located about 8 km off the western coast of Korea. The cavern is about 130–150 m below the sea bottom, which is covered by a 4.8–19.5 m silty clay stratum. An isotopic composition (δ2H and δ18O) of the marine subsurface waters falls on a mixing line between terrestrial groundwater and seawater. Vertical EC profiling at the cavern boreholes revealed the existence of a fresh water zone. An increase in the contents of ferrous iron and manganese and a decrease in levels of nitrate, bicarbonate and cavern seepage were recorded in August 2006, indicating a decreased submarine groundwater flux originating from land, mainly caused by an elevated cavern gas pressure. It is suggested in this study that the main source of fresh waters in the man-made undersea cavern is the submarine groundwater discharge mainly originating from the land.  相似文献   

5.
The Ischia geothermal system is hosted by silicic rocks of the Quaternary Potassic Roman Province, in southern Italy. Exploration drilling down to 1156 m depth in the mid-1950s provided information on boiling profiles (up to 250°C) and on the depth and permeability of the potential reservoirs. Discharge fluid samples were collected and analyzed to define the inflow of surrounding seawater (C1 ranges from 2.5 to 20 g/kg) into the system.Analyses of samples from surface manifestations and shallow wells collected during 1983 and 1988 point to the existence of three distinct mixing regimes, involving three water components. A dishomogeneous body of diluted water (Cl less than 2.5 g/kg), that occurs at depths > 700 m and reequilibrates at 240°C at least, is overlain by an aquifer of groundwater variably mixed with variably seawater (Cl from 4 to 10 g/kg), which tends to reequilibrate at 160°C. Steam-heated waters locally develop and act as dilutants of the rising geothermal fluids.Dilution, mixing, and evaporation of the ascending chloride fluids are supported by oxygen and hydrogen isotopic data the thermal waters being enriched in 18O and D with respect to local meteoric water by up to 7 and 30‰, respectively. The relative composition of the major cations in thermal solutions was used to discriminate the two main groups of thermal waters, the reservoir temperatures of which are estimated from the Na/K-gethermometer. K-Mg geothermometer indicates reequilibration in near-surface conditions.The isotopic composition of the fumarolic steam varies from −7 to −12‰ in ∂8O and from − 35 to − 70‰ in ∂D, in agreement with a deep mixed fluid that boils adiabatically from 240 to 80°C. The deuterium content of the H2O-H2 pair gives enrichment factor of about 830‰, corresponding to equilibrium temperature conditions slightly higher than the surface boiling temperatures. The ∂13C of CO2is almost constant at −4.5‰ (1δ=0.4), suggesting an important magmatic contribution, and the ∂18O values of CO2appears to in equilibrium with accompanying steam at the measured temperatures.The CO2/Ar and H2/Ar chemical ratios have been used to derive aquifer temperatures, the values obtained being consistent with those of solute geothermometers.  相似文献   

6.
Thermal springs of the Boundary Creek hydrothermal system in the southwestern part of Yellowstone Park outside the caldera boundary vary in chemical and isotopic composition, and temperature. The diversity may be accounted for by a combination of processes including boiling of a deep thermal water, mixing of the deep thermal water with cool meteoric water and/or with condensed steam or steam-heated meteoric water, and chemical reactions with surrounding rocks. Dissolved-silica, Na+, K+ and Ca2+ contents of the thermal springs could result from a thermal fluid with a temperature of 200 ± 20°C. Chloride-enthalpy and silica-enthalpy mixing models suggest mixing of 230°C, 220 mg/l Cl− thermal water with cool, low-Cl− components. A 350 to 390°C component with Cl− ≥ 300 mg/l is possibly present in thermal springs inside the caldera but is not required to fit observed spring chemical and isotopic compositions. Irreversible mass transfer models in which a low-temperature water reacts with volcanic glass as it percolates downward and warms, can account for observed pH and dissolved-silica, K+, Na+, Ca2+ and Mg2+ concentrations, but produces insufficient Cl− or F− for measured concentrations in the warm springs. The ratio of aNa/aH, and Cl− are best accounted for in mixing models. The water-rock interaction model fits compositions of acid-sulfate waters observed at Summit Lake and of low-Cl− waters involved in mixing.The cold waters collected from southwestern Yellowstone Park have δD values ranging from −118 to −145 per mil and δ18O values of −15.9 to −19.4 per mil. Two samples from nearby Island Park have δD values of −112 and −114 per mil and δ18O values of −15.1 and −15.3 per mil. All samples of thermal water plot significantly to the right of the meteoric water line. The low Cl− and variable δD values of the thermal waters indicate isotopic compositions are derived by extensive dilution with cold meteoric water and by steam separation on ascent to the surface. Many of the hot springs with higher δD values may contain in addition a significant amount of high-D, low-Cl−, acid-sulfate or steam-heated meteoric water. Mixing models, Cl− content and isotopic compositions of thermal springs suggest that 30% or less of a deep thermal component is present. For example, the highest-temperature springs from Three Rivers, Silver Scarf and Upper Boundary Creek thermal areas contain up to 70% cool meteoric water and 30% hot water components, springs at Summit Lake and Middle Boundary Creek spring 57 are acid-sulfate or steam-heated meteoric water; springs 27 and 48 from Middle Boundary Creek and 49 from Mountain Ash contain in excess of 50% acid-sulfate water; and Three Rivers spring 46 and Phillips could result from mixing hot water with 55% cool meteoric water followed by mixing of acid-sulfate water. Extensive dilution by cool meteoric water increases the uncertainties in quantity and nature of the deep meteoric, thermal component.  相似文献   

7.
Enhanced production of unconventional hydrocarbons in the United States has driven interest in natural gas development globally, but simultaneously raised concerns regarding water quantity and quality impacts associated with hydrocarbon extraction. We conducted a pre‐development assessment of groundwater geochemistry in the critically water‐restricted Karoo Basin, South Africa. Twenty‐two springs and groundwater samples were analyzed for major dissolved ions, trace elements, water stable isotopes, strontium and boron isotopes, hydrocarbons and helium composition. The data revealed three end‐members: a deep, saline groundwater with a sodium‐chloride composition, an old, deep freshwater with a sodium‐bicarbonate‐chloride composition and a shallow, calcium‐bicarbonate freshwater. In a few cases, we identified direct mixing of the deep saline water and shallow groundwater. Stable water isotopes indicate that the shallow groundwater was controlled by evaporation in arid conditions, while the saline waters were diluted by apparently fossil meteoric water originated under wetter climatic conditions. These geochemical and isotopic data, in combination with elevated helium levels, suggest that exogenous fluids are the source of the saline groundwater and originated from remnant seawater prior to dilution by old meteoric water combined with further modification by water‐rock interactions. Samples with elevated methane concentrations (>14 ccSTP/kg) were strongly associated with the sodium‐chloride water located near dolerite intrusions, which likely provide a preferential pathway for vertical migration of deeply sourced hydrocarbon‐rich saline waters to the surface. This pre‐drill evaluation indicates that the natural migration of methane‐ and salt‐rich waters provides a source of geogenic contamination to shallow aquifers prior to shale gas development in the Karoo Basin.  相似文献   

8.
The Sierra La Primavera, a late Pleistocene rhyolitic caldera complex in Jalisco, México, contains fumaroles and large-discharge 65°C hot springs that are associated with faults related to caldera collapse and to later magma insurgence. The nearly-neutral, sodium bicarbonate, hot springs occur at low elevations at the margins of the complex, whereas the water-rich fumaroles are high and central.The Comisión Federal de Electricidad de México (CFE) has recently drilled two deep holes at the center of the Sierra (PR-1 and Pr-2) and one deep hole at the western margin. Temperatures as high as 285°C were encountered at 1160 m in PR-1, which produced fluids with 820 to 865 mg/kg chloride after flashing to one atmosphere. Nearby, PR-2 encountered temperatures to 307°C at 2000 m and yielded fluids with chloride contents fluctuating between 1100 and 1560 mg/kg after flashing. Neither of the high-temperature wells produced steam in commercial quantities. The well at the western margin of the Sierra produced fluids similar to those from the hot springs. The temperature reached a maximum of 100°C near the surface and decreased to 80°C at 2000 m.Various geothermometers (quartz conductive, Na/K, Na-K-Ca, δ18O(SO4-H2O) and D/H (steam-water) all yield temperatures of 170 ± 20°C when applied to the hot spring waters, suggesting that these spring waters flow from a large shallow reservoir at this temperature. Because the hot springs are much less saline than the fluids recovered in PR-1 and PR-2, the mixed fluid in the shallow reservoir can contain no more than 10–20% deep fluid. This requires that most of the heat is transferred by steam. There is probably a thin vapor-dominated zone in the central part of the Sierra, through which steam and gases are transferred to the overlying shallow reservoir. Fluids from this reservoir cool from 170°C to 65°C by conduction during the 5–7 km of lateral flow to the hot springs.  相似文献   

9.
The thermal energy balance and the temperature profile of the Hakone volcano are considered quantitatively. Across the Hakone volcano and its surroundings the heat flow values vary from 10–1 to 103 mW/m2, due to thermal conduction and mass flow involving volcanic steam and hot spring discharge. An area with extremely low heat flow is observed in the western side of the caldera showing the presence of percolating meteoric water. The hydrothermal activity is intense in the eastern half of the caldera.The total heat discharge from the high temperature zone (discharge area) of the Hakone volcano amounts to 11.0×107 W. The magmatic steam energy discharge is 95.0×106 W. The thermal energy by redistribution of the terrestrial heat flow by the lateral deep ground water flow is calculated to be 9.00×106 W. For the model having the vertical vent in the volcano's central part up to 1 km depth below the ground surface from a magma reservoir the computed temperature distribution is consistent with the observed values. The depth of the magma reservoir is 7 km below the ground surface and the diameter is 5 km.  相似文献   

10.
Temperatures of aquifers feeding thermal springs and wells in Long Valley, California, estimated using silica and Na-K-Ca geothermometers and warm spring mixing models, range from 160/dg to about 220°C. This information was used to construct a diagram showing enthalpy-chloride relations for the various thermal waters in the Long Valley region. The enthalpy-chloride information suggests that a 282 ± 10°C aquifer with water containing about 375 mg chloride per kilogram of water is present somewhere deep in the system. That deep water would be related to 220°C Casa Diablo water by mixing with cold water, and to Hot Creek water by first boiling with steam loss and then mixing with cold water. Oxygen and deuterium isotopic data are consistent with that interpretation. An aquifer at 282°C with 375 mg/kg chloride implies a convective heat flow in Long Valley of 6.6 × 107 cal/s.  相似文献   

11.
Groundwater discharges in the western Canadian oil sands region impact river water quality. Mapping groundwater discharges to rivers in the oil sands region is important to target water quality monitoring efforts and to ensure injected wastewater and steam remain sequestered rather than eventually resurfacing. Saline springs composed of Pleistocene‐aged glacial meltwater exist in the region, but their spatial distribution has not been mapped comprehensively. Here we show that formation waters discharge into 3 major rivers as they flow through the Athabasca Oil Sands Region adjacent to many active oil sands projects. These discharges increase river chloride concentrations from river headwaters to downstream reaches by factors of ~23 in the Christina River, ~4 in the Clearwater River, and ~5 in the Athabasca River. Our survey provides further evidence for the substantial impact of formation water discharges on river water quality, even though they comprise less than ~2% of total streamflow. Geochemical evidence supporting formation water discharges as the leading control on river salinity include increases in river chloride concentrations, Na/(Na + Ca) ratios, Cl/(Cl + SO4) ratios and decreases in 87Sr/86Sr ratios; each mixing trend is consistent with saline groundwater discharges sourced from Cretaceous or Devonian aquifers. These regional subsurface‐to‐surface connections signify that injected wastewater or steam may potentially resurface in the future, emphasizing the critical importance of mapping groundwater flow paths to understand present‐day streamflow quality and to predict the potential for injected fluids to resurface.  相似文献   

12.
Coupled modelling of surface and subsurface systems is a valuable tool for quantifying surface water–groundwater interactions. In the present paper, the 3-D non-steady state Navier–Stokes equations, after Reynolds averaging and with the assumption of a hydrostatic pressure distribution, are for the first time coupled to the 3-D saturated groundwater flow equations in an Integrated suRface watEr–grouNdwater modEl (IRENE). A finite-difference method is used for the solution of the governing equations of IRENE. A semi-implicit scheme is used for the discretisation of the surface water flow equations and a fully implicit scheme for the discretisation of the groundwater flow equations. The two sets of equations are coupled at the common interface of the surface water and groundwater bodies, where water exchange takes place, using Darcy’s law. A new approach is proposed for the solution of the coupled surface water and groundwater equations in a simultaneous manner, in such a fashion that gives computational efficiency at low computational cost. IRENE is verified against three analytical solutions of surface water–groundwater interaction, which are chosen so that different components of the model can be tested. The model closely reproduces the results of the analytical solutions and can therefore be used for analysing and predicting surface water–groundwater interactions in real-world cases.  相似文献   

13.
Heat-flow and coal-maturation data suggest that the thermal history of the San Juan Basin has been influenced by magmatic and volcanic activity in the San Juan Mountains-San Juan volcanic field located to the north of the Basin. Time-dependent isothermal step models indicate that the observed heat flow may be modelled by a (near) steadystate isothermal step extending from 30–98 km depth whose edge underlies the northern San Juan Basin. The observed maturation levels of the Fruitland formation coals in the northern and central Basin, however, require more heat than can be associated with conduction from a deep thermal source (steady-state step) and from the shallow crustal batholith which underlies the San Juan volcanic field. Magmatic activity within the Basin does not appear to be a reasonable source of additional heat. Increased burial depths of the coals may explain some of the elevated maturation levels observed in the central and northern Basin, but it seems likely that an additional source of heat is still required. Heat advection by groundwater movement may have influenced the coal maturation levels in the Basin as well. Both magmatic activity associated with the emplacement of the San Juan batholith and elevated geothermal gradients associated with the steady-state thermal source at depth may have contributed to heating of the groundwater. An appreciation of heat advection by groundwater flow may therefore be most important to understanding regional patterns of heat flow and hydrocarbon maturation.  相似文献   

14.
Small and large maars exist associated with small and large diatremes, respectively, their subsurface feeder structures. The problem of size and growth of maar-diatreme volcanoes is discussed from a phreatomagmatic point of view from field data, some geophysical data, and short-lived historic maar eruptions. A hydrostatic pressure barrier of usually about 20–30 bars is assumed to control the maximum depth level of explosive magma/groundwater interactions. Similar to the situation in submarine and subglacial volcanism, initial maar-forming water vapour explosions are therefore assumed to occur at shallow depth and to produce a small maar with a shallow diatreme. Because of limited availability of groundwater and ejection of groundwater in the form of steam, the confining pressure barrier is displaced downward. Consequently, water vapour explosions can take place at consecutively deeper levels with the result that the diatreme penetrates downward and grows in size. Since maars are collapse craters resulting from ejection of wallrocks fragmented by water vapour explosions at the level of the diatreme root zone, downward penetration of a diatreme not only results in increase in size of a diatreme but also in increase in size of the overlying maar. As availability of groundwater in limited amounts controls formation of diatremes and their downward penetration, lack of groundwater enables magma to rise within a diatreme and to form a scoria cone or lava lake within the maar, as is frequently found in volcanic fields such as the Eifel area in Germany. In contrast, availability of large amounts of water in near surface environments such as shallow marine, lake, water-rich coastal plains, or water-rich fluviatile gravel beds prevents formation of maars and deep diatremes but causes formation of tuff rings.  相似文献   

15.
Subsurface flow and heat transport near Freienbrink, NE Germany, was simulated in order to study groundwater–surface water exchange between a floodplains aquifer and a section of the lowland River Spree and an adjacent oxbow. Groundwater exfiltration was the dominant process, and only fast surface water level rises resulted in temporary infiltration into the aquifer. The main groundwater flow paths are identified based on a 3D groundwater flow model. To estimate mass fluxes across the aquifer–surface water interfaces, a 2D flow and heat transport modelling approach along a transect of 12 piezometers was performed. Results of steady‐state and transient water level simulations show an overall high accuracy with a Spearman coefficient ρ = 0.9996 and root mean square error (RMSE) = 0.008 m. Based on small groundwater flow velocities of about 10?7 to 10?6 ms?1, mean groundwater exfiltration rates of 233 l m?2 d?1 are calculated. Short periods of surface water infiltration into the aquifer do not exceed 10 days, and the infiltration rates are in the same range. The heat transport was modelled with slightly less accuracy (ρ = 0.8359 and RMSE = 0.34 °C). In contrast to the predominant groundwater exfiltration, surface water temperatures determine the calculated temperatures in the upper aquifer below both surface water bodies down to 10 m during the whole simulation period. These findings emphasize prevailing of heat conduction over advection in the upper aquifer zones, which seems to be typical for lowland streams with sandy aquifer materials and low hydraulic gradients. Moreover, this study shows the potential of coupled numerical flow and heat transport modelling to understand groundwater–surface water exchange processes in detail. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

16.
The potential of a geothermal area is primarily dependent on volume and temperature of the reservoir and adequacy of fluid supply. Inadequate fluid supply may be a more common limiting factor than inadequate heat supply, for heat stored in the upper 10,000 ft of many hot spring systems is 1,000 to 10,000 times their annual natural heat flow. Except in very porous reservoirs, most of this heat is stored in rocks rather than in pore fluids. Geothermal fields can be classified as hot spring systems or as deep insulated reservoirs with little surface expression; gradations also exist. Hot spring systems have high near-surface permeability, at least locally on faults and fractures, permitting fluids to escape at high rates. Owing to vigorous circulation and escaping fluids and heat, near-surface temperatures are high, but temperatures deep in the system are lower than would prevail with inhibited escape. Deep reservoirs with little surface expression require permeable reservoir rocks capped by insulating rocks of low permeability. Larderello, Italy, and Salton Sea, California, have slight leakage, but others may have no leakage. Liquid water, which can be at temperatures far above 100° C because of existing pressures, is generally the dominant fluid. Steam can form by boiling as hot water rises to levels of lower pressure. However, in several explored systems the heat supply is so high and rate of discharge of water so low that steam exists even deep in the system. Dry steam areas are probably rare. About 30 areas in the United States have been explored for geothermal energy, but dry steam has been proved only at « The Geysers ». Extensive utilisation of geothermal energy must therefore depend largely upon steam « flashed » from hot water with decrease in pressure. Problems that confront broad utilisation of geothermal energy include: 1) discovery of reservoirs with adequate supply of energy and natural fluids; 2) deposition of CaCO; or SiO2; 3) chemical corrosion; 4) objectionable chemicals in some effluents; and 5) inapplicability of existing public laws. The optimum environment for a geothermal reservoir includes:
  1. 1.
    Potent source of heat, such as a magma chamber. A depth of at least two miles provides enough pressure to insure water of high temperature; 5 miles may be too deep for effective transfer of heat to circulating water. Such heat sources are most likely to occur in regions of late Cenozoic volcanism.  相似文献   

17.
Hot springs and steam vents on the slopes of Nevado del Ruiz volcano provide evidence regarding the nature of hydrothermal activity within the summit and flanks of the volcano. At elevations below 3000 m, alkali-chloride water is discharged from two groups of boiling springs and several isolated warm springs on the western slope of Nevado del Ruiz. Chemical and isotopic geothermometers suggest that the boiling springs are fed by an aquifer having a subsurface equilibration temperature of at least 175°C, and the sampled warm spring is fed by an aquifer having a subsurface equilibration temperature near 150°C. Similarities in conservative solute ratios (e.g., B/Cl) indicate that the alkali-chloride waters may be related to a single reservoir at depth. Isotopic ratios of hydrogen and oxygen indicate that recharge for the alkali-chloride aquifers comes mostly from higher elevations on the volcano. Steam vents and steam-heated bicarbonate-sulfate springs at higher elevations, along a linear structural trend with the alkali-chloride springs, may be derived partly from the alkali-chloride water at depth by boiling. Steam from the vents (84°C) yields a gas geothermometer temperature of 209°C. Acid-sulfate-chloride and acid-sulfate waters are discharged widely from warm springs above 3000 m on the northern and eastern slopes of Nevado del Ruiz. Similarities in B/Cl and SO4/Cl ratios suggest that the acid waters are mixtures of water from an acid-sulfate-chloride reservoir with various proportions of shallow, dilute groundwater. The major source of sulfate, halogens, and acidity for the acid waters may be high-temperature magmatic gases. Available data on hot spring temperatures and compositions indicate that they have remained fairly stable since 1968. However, the eruption of November 13, 1985 apparently caused an increase in sulfate concentration in some of the acid springs that peaked about a year after the eruption. Long-term monitoring of hot spring compositions over many years will be required to better define the effects of volcanic activity on the Nevado del Ruiz hydrothermal system.  相似文献   

18.
The Active Crater at Rincón de la Vieja volcano, Costa Rica, reaches an elevation of 1750 m and contains a warm, hyper-acidic crater lake that probably formed soon after the eruption of the Rio Blanco tephra deposit approximately 3500 years before present. The Active Crater is buttressed by volcanic ridges and older craters on all sides except the north, which dips steeply toward the Caribbean coastal plains. Acidic, above-ambient-temperature streams are found along the Active Crater's north flank at elevations between 800 and 1000 m. A geochemical survey of thermal and non-thermal waters at Rincón de la Vieja was done in 1989 to determine whether hyper-acidic fluids are leaking from the Active Crater through the north flank, affecting the composition of north-flank streams.Results of the water-chemistry survey reveal that three distinct thermal waters are found on the flanks of Rincón de la Vieja volcano: acid chloride–sulfate (ACS), acid sulfate (AS), and neutral chloride (NC) waters. The most extreme ACS water was collected from the crater lake that fills the Active Crater. Chemical analyses of the lake water reveal a hyper-acidic (pH0) chloride–sulfate brine with elevated concentrations of calcium, magnesium, aluminum, iron, manganese, copper, zinc, fluorine, and boron. The composition of the brine reflects the combined effects of magmatic degassing from a shallow magma body beneath the Active Crater, dissolution of andesitic volcanic rock, and evaporative concentration of dissolved constituents at above-ambient temperatures. Similar cation and anion enrichments are found in the above-ambient-temperature streams draining the north flank of the Active Crater. The pH of north-flank thermal waters range from 3.6 to 4.1 and chloride:sulfate ratios (1.2–1.4) that are a factor of two greater than that of the lake brine (0.60). The waters have an ACS composition that is quite different from the AS and NC thermal waters that occur along the southern flank of Rincón de la Vieja.The distribution of thermal water types at Rincón de la Vieja strongly indicates that formation of the north-flank ACS waters is not due to mixing of shallow, steam-heated AS water with deep-seated NC water. More likely, hyper-acidic brines formed in the Active Crater area are migrating through permeable zones in the volcanic strata that make up the Active Crater's north flank. Dissolution and shallow subsurface alteration of north-flank volcanoclastic material by interaction with acidic lake brine, particularly in the more permeable tephra units, could weaken the already oversteepened north flank of the Active Crater. Sector collapse of the Active Crater, with or without a volcanic eruption, represents a potential threat to human lives, property, and ecosystems at Rincón de la Vieja volcano.  相似文献   

19.
The parallel physically-based surface–subsurface model PARFLOW was used to investigate the spatial patterns and temporal dynamics of river–aquifer exchange in a heterogeneous alluvial river–aquifer system with deep water table. Aquifer heterogeneity at two scales was incorporated into the model. The architecture of the alluvial hydrofacies was represented based on conditioned geostatistical indicator simulations. Subscale variability of hydraulic conductivities (K) within hydrofacies bodies was created with a parallel Gaussian simulation. The effects of subscale heterogeneity were investigated in a Monte Carlo framework. Dynamics and patterns of river–aquifer exchange were simulated for a 30-day flow event. Simulation results show the rapid formation of saturated connections between the river channel and the deep water table at preferential flow zones that are characterized by high conductivity hydrofacies. Where the river intersects low conductivity hydrofacies shallow perched saturated zones immediately below the river form, but seepage to the deep water table remains unsaturated and seepage rates are low. Preferential flow zones, although only taking up around 50% of the river channel, account for more than 98% of total seepage. Groundwater recharge is most efficiently realized through these zones. Subscale variability of Ksat slightly increased seepage volumes, but did not change the general seepage patterns (preferential flow zones versus perched zones). Overall it is concluded that typical alluvial heterogeneity (hydrofacies architecture) is an important control of river–aquifer exchange in rivers overlying deep water tables. Simulated patterns and dynamics are in line with field observations and results from previous modeling studies using simpler models. Alluvial heterogeneity results in distinct patterns and dynamics of river–aquifer exchange with implications for groundwater recharge and the management of riparian zones (e.g. river channel-floodplain connectivity via saturated zones).  相似文献   

20.
A numerical model previously developed to systematically examine groundwater flow in vertical section near shallow surface water bodies such as lakes, wetlands and ponds is further developed to include simulation of the distribution patterns of hydrogeochemical and stable isotopic tracers in relation to the surface water body and the geometry of distribution patterns of the tracers in the groundwater release zone of the lake. Many different possible flow regimes are identified, however, in this paper attention is focused on flow-through water bodies, as these are the flow regimes observed in field validation. Two shallow lakes on the Swan Coastal Plain of south-west Western Australia are the subject of field studies where hydrogeochemical and stable isotopes are used to validate the flow-through groundwater flow regime predicted by the modelling confirming the validity of the approach. The flow regime transition diagrams introduced in earlier papers are extended to include consideration of the hydrogeochemical and stable isotopic indices ClL/Cl+ and (1000+δL)/(1000+δ+). These ratios are introduced as an additional two of nine non-dimensional ratios that are necessary to analyse the problem. The ratios represent the chloride and isotopic composition (ClL and δL), respectively, in the groundwater release zones of the lakes, relative to these parameters in the groundwater capture zone (Cl+ and δ+) for the lake. Field data from the case studies plotted on appropriately configured transition diagrams demonstrates the overall validity of the modelling approach and its underlying assumptions. It is concluded that isotopic and hydrogeochemical data are invaluable in interpreting the interaction between lakes or wetlands and regional aquifers as it is very difficult to make physical or hydraulic measurements in the field that allow an understanding of lake–aquifer interaction. The tools and concepts developed that are summarized in the presented transition diagrams are invaluable starting points for the consideration and analysis of other case-specific examples of groundwater–surface water interaction and will improve the scientific basis of decision-making concerning lake and wetland management and groundwater interaction by water resource and environmental managers.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号