共查询到20条相似文献，搜索用时 46 毫秒
1.
由于深水浮式平台的运动幅度较固定式平台增大,其运动与下部立管的动力耦合变得更加明显。研究了上部平台运动对水下立管涡激振动的影响,基于有限元数值模拟,建立了与结构运动耦合的立管尾迹流场的涡激升力、流体阻力模型,进行了"平台运动-立管涡激振动"整体系统的动响应数值模拟,分析了平台横荡运动的幅值、频率等因素对水下立管涡激振动的影响。结果表明,上部平台的振动会在沿着立管展向传播的过程中被放大(称为响应放大);与不考虑平台运动相比,立管的动响应位移增大了多倍,而且振幅放大倍数随着模态阶数的降低而增大;平台横荡振幅越大,立管振动幅值也越大,但是振幅放大倍数的变化不明显。 相似文献
2.
质量比对柔性立管涡激振动影响实验研究 总被引：1，自引：0，他引：1
质量比是影响海洋立管涡激振动的一个重要因素.通过在室内物理实验中使立管模型内部分别充填空气、水和沙来改变立管的质量比,从而研究质量比对柔性细长立管涡激振动的影响.实验结果表明:在相同流速下,质量比大的立管模型所激起的模态更高.在低约化速度区域,空管和水管的涡激振动响应频率与涡脱落频率相同,沙管的响应频率则与自振频率更接近,三种质量比立管的响应位移较接近;在高约化速度区域,三种质量比的立管模型的响应频率处于自振频率和涡脱落频率之间,但空管的响应频率随约化速度的增大而不断增大,同一流速下,质量比大的立管模型响应位移小,其中空管的涡激振动响应一直处于大振幅的锁定状态下.共振区域对应约化速度的范围随着质量比增大而减小. 相似文献
3.
海洋立管抑振装置优化布置的实验研究 总被引：1，自引：0，他引：1
设计1种梯形截面的三螺旋导板抑振装置,在实验室大型水槽进行海洋立管涡激振动实验.通过改变这种抑振装置的覆盖方式和覆盖范围,研究梯形截面螺旋导板的不同覆盖方式和覆盖范围对抑制海洋立管涡激振动的作用.实验时用动态电阻应变仪采集立管模型横向和顺流向的动态响应数据,并利用雨流计数法对模型进行疲劳分析.实验结果表明:在外流流速相同的条件下,三螺旋导板各种覆盖方案对涡激振动都有抑制作用;随着螺旋导板覆盖率的增加,立管的振动减弱,疲劳寿命增加;覆盖螺旋导板的立管顺流向振动频率明显降低,横向振动频率当覆盖率较高时有所降低,覆盖率较低时基本没有变化. 相似文献
4.
深水浮式平台垂荡运动与水下柔性立管涡激振动的动力耦合 总被引：1，自引：0，他引：1
基于有限元数值模拟,进行了"平台垂荡-顶张力立管涡激振动"整体系统的动响应数值模拟。动响应模型考虑了立管尾迹流场的水动力与结构动力的耦合和垂荡引起的立管结构刚度的时变特性;分析了平台垂荡运动的频率、模态阶数等因素对水下顶张力立管涡激振动的影响。数值结果表明:与不考虑平台运动相比,立管的动响应位移会增大;立管响应幅值随着模态阶数的降低而增大;在响应过程中,尤其对于低阶模态,会出现响应的模态转换现象。鉴于在平台垂荡和涡激振动的共同作用下,立管的动响应会大于涡激振动、参数激励分别单独作用的响应,建议在立管实际工程设计中应该考虑平台运动和涡激振动耦合激励作用下的结构动响应。 相似文献
5.
大长细比柔性杆件涡激振动实验 总被引：3，自引：1，他引：2
涡激振动(vortex-induced vibration,VIV)是导致深海细长柔性立管发生疲劳破坏的重要因素。采用实验观测手段研究了长细比为1 750的柔性立管多模态涡激振动特性。实验中,通过采用拖车拖拉立管模型在水池中匀速行进来模拟均匀流作用下的涡激振动响应。利用光纤光栅传感器测量立管模型在横流向(cross-flow,CF)和顺流向(in-line,IL)的应变,进而通过模态分解的方法,获得立管模型涡激振动的位移。在此基础上,研究了CF以及IL方向的响应频率、位移标准差的平均值和最大值等随流速的变化规律,并分析了立管模型上测点的运动轨迹及其影响因素。 相似文献
6.
《中国海洋大学学报(自然科学版)》2021,(8)
基于内波流场的eKdv理论并结合尾流振子模型和挠性立管的非线性振动方程建立内波流场中悬链线立管计算模型,研究了内波流场中悬链线立管升力方向运动的响应问题,并分析了内孤立波波高和密度跃层位置对悬链线立管升力方向响应的影响。结果表明:内孤立波经过悬链线立管时会引起突然增大的涡激振动,其中高阶模态占主导;涡激振动最大位移发生于流体密度跃层位置附近;内孤立波波高增大以及密度跃层位置加深会使立管转变为更高阶模态振动,并且密度跃层位置加深会使立管涡激振动位移明显减小。 相似文献
7.
基于控制尾流,阻止立管尾流漩涡脱落转换路径的涡激振动抑制机理,设计三角形尾翼、片状尾翼及交错尾翼等三种抑振装置。三种抑振装置分别安装于立管模型表面,立管模型采用外径为18 mm的透明有机玻璃管。通过在均匀流场中进行安装有该抑振装置的立管模型涡激振动试验,研究三种抑振装置对立管涡激振动的抑制效率,并通过与配重裸管的涡激振动数据对比,分析抑振装置对立管动力响应的影响规律。研究结果表明,三种抑振装置均取得了明显的抑振效果,与配重裸管相比,安装片状尾翼及交错尾翼的立管模型抑制效率可达90%以上,安装三角形尾翼后立管模型振动频率略有减小,而安装片状尾翼及交错尾翼的立管模型没有明显的主导频率。 相似文献
8.
以深海顶端张紧式立管为研究对象,基于圆柱体受迫振荡实验数据和能量平衡原理预报立管涡激振动响应及其诱发的疲劳损伤度,各主要参数随机化,应用响应面法建立了涡激振动疲劳安全系数与极限状态方程关系,研究了疲劳安全系数对结构可靠性的影响,并分析了各随机变量的灵敏度。研究结果表明:1)随着疲劳安全系数的增大,结构失效概率逐渐减小,且失效概率的减小幅度随疲劳安全系数的增加而趋缓。疲劳安全系数SF无需超过20。2)增加疲劳安全系数SF可降低疲劳载荷不确定量B、S-N曲线参数A、顶张力、流速、外径和壁厚等立管及环境随机变量对结构涡激振动疲劳损伤可靠性的影响。3)立管各参数中,流速、外径和壁厚均值越大,立管结构安全度越低,顶张力对结构影响相反;各参数的标准差越大,结构可靠度越低。均值灵敏度由大到小依次为顶张力、流速、外径和壁厚,标准差灵敏度由大到小依次为流速、张力、外径和壁厚。4)壁厚对深海顶张紧式立管涡激振动所致疲劳损伤影响很小,可忽略其影响。研究成果可为深海顶张紧式立管涡激振动疲劳安全系数的选取提供参考。 相似文献
9.
10.
《中国海洋大学学报(自然科学版)》2015,(10)
涡激振动潮流能转换装置是适用于低流速、浅水地区的海洋潮流能资源开发的一种新型装置。本文对涡激振动装置的工作机理进行研究,利用涡激振动流体力分解模型,建立了涡激振动方程和预测模型并对预测模型进行了验证。建立涡激振动的数学耦合模型,结合理论分析和预测模型设计了模型实验样机,进行水槽实验,测试流速、弹性系数等参数对涡激振动响应的影响,实验数据验证了数学耦合模型的合理性。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.