共查询到20条相似文献，搜索用时 62 毫秒
1.
为了能够利用遥感图像快速准确地提取围海养殖矢量信息,本文选取养殖水体、堤坝及育苗室等交错分布的海参围海养殖区域作为研究区域,根据研究区域Sentinel-2遥感影像的光谱特征,选用归一化差异水体指数（Normalized Difference Water Index,NDWI）、改进归一化差异水体指数（Modified Normalized Difference Water Index,MNDWI）和增强水体指数（Enhanced Water Index,EWI）三类水体指数,分别进行提取实验,利用同时期高空间分辨率的高分二号卫星（GF-2）影像作为参考,验证不同方法的提取精度,精度评价结果表明：相较MNDWI和EWI两类水体指数,NDWI的分类精度更高,且利用NDWI提取研究区域的围海养殖信息的效果更好,所以该方法可在养殖区域的动态监测和规划管理中发挥数据支撑作用。 相似文献
2.
准确计算珊瑚礁的面积是评估其资源、环境效应的基础,但我国迄今对南海珊瑚礁的面积估算仍缺乏共识,缺少可靠的估算方法是导致这一现象的重要原因。针对这一问题,本文以西沙群岛羚羊礁为例,提出了一种利用多时相多光谱遥感影像低成本半自动化估算珊瑚礁面积的方法。首先快速目视确定地貌带分界线的粗略位置,然后利用基于梯度向量场的主动轮廓线模型（Gradient Vector Flow-Snake, GVF-Snake）实现这些分界线位置的自动精化,最后将不同时相的瞬时分界线转换为面要素进行多时相的融合,从而得到珊瑚礁的面积。基于53景Sentinel-2 多光谱成像仪（MSI）影像的实验表明,羚羊礁的总面积为17.22 km2（Landsat 8 陆地成像仪（OLI）用于方法稳定性的验证,得到的羚羊礁面积为17.29 km2）,其中礁前斜坡、礁坪?潟湖坡、潟湖的面积分别为1.76 km2、10.29 km2、5.17 km2。该数值与实测数据具有较好的一致性。具体地,该方法获得的地貌带分界点与实测水深所指示分界点的位置偏差能控制在0.2～4.9 m的范围内（不超过0.5个像素）,珊瑚礁最外轮廓线与30 m等深线的位置偏差亦在1个像素大小内（5.7～9.5 m）,而估算面积与高分辨率WorldView-2影像解译得到的面积差异为0.02%。同时,该方法获得的珊瑚礁边界线的完整度、正确度、提取质量精度能够由单时相平均的60%、64%和54%分别提高至84%、83%和72%。此外,该方法能够减小基于不同遥感数据源的珊瑚礁面积估算结果的差异,即6景以上的多时相Sentinel-2 MSI和Landsat 8 OLI影像提取的珊瑚礁面积标准差分别不超过0.01 km2和0.05 km2,仅相当于珊瑚礁总面积的0.2%和0.5%。总而言之,该方法能够用低成本的10 m分辨率Sentinel-2 MSI和30 m分辨率Landsat 8 OLI影像获得接近1.8 m分辨率WorldView-2影像的面积估算精度,且具有良好的稳定性和可靠性。 相似文献
3.
为利用遥感技术快速、及时的掌握厦门近岸海域水体中悬浮颗粒物的总体分布情况,现场测量了厦门海域水体的下行入射辐射、天空光以及经过水气界面后反射回的辐射,计算了该海域水体表面的离水辐射获得了水体表面以上遥感反射率;同时采集了与光谱信息同步的水体样品,并分析了水体中的悬浮颗粒物质量浓度,获取了对应站位的水体反射波谱曲线和采集样品的浓度数据.通过研究不同站位水体的反射光谱数据,依据GF-WFV波段设置,对现场实测的光谱数据进行了拟合,并创建了基于GF-WFV拟合波段的悬浮颗粒物浓度经验反演算法.通过研究发现拟合(Rrs3+Rrs4)/Rrs2(其中Rrs1、Rrs2、Rrs3、Rrs4分别是GF-WFV第1、2、3、4波段的遥感反射率)同实测水体悬浮颗粒物质量浓度之间的决定系数为0.655,依据研究得出的反演算法反演该海域水体悬浮颗粒物质量浓度,其均方根误差为11.03 mg/dm3,相对误差为8.40 mg/dm3.利用同步的GF-WFV遥感数据对厦门近岸水体中总悬浮颗粒物质量浓度进行了研究,获取了研究区水体悬浮颗粒物的空间分布情况,结果表明GF-WFV遥感数据能很好的反映厦门近岸水体悬浮颗粒物浓度分布状况. 相似文献
4.
采用星星交叉检验方法,比对了VIIRS和MODIS在中国渤海遥感反射率获取能力。由对比结果得出:在近岸海区VIIRS和MODIS观测能力相似,在浑浊水体VIIRS的遥感反射率高于MODIS。同时基于2012年9月辽东湾航次获取的现场遥感反射率数据对VIIRS在渤海海区的反演能力进行了星地检验。结果表明:VIIRS在中国近岸二类水体的反演效果较好,但出现了低估现象,在反演精度上,VIIRS卫星Rrs产品的反演误差远离近红外波段而增大,随水体悬浮颗粒浓度的增加而增大。 相似文献
5.
本文使用Landsat-8影像、Sentinel-2影像、高分6号影像和ASTER GDEM数据等多源遥感数据,采用随机森林监督分类方法提取珠海淇澳岛红树林分布范围,对比不同影像数据提取红树林的精度及适用性。实验结果表明：使用三类遥感影像分别进行红树林范围提取,Sentinel-2影像提取红树林范围总体精度最高;在三类遥感影像中分别增加DEM数据、波段指数和纹理信息后,红树林范围提取精度可进一步提升;增加DEM数据后,精度提升最明显,高分6号影像增加纹理信息后,精度也有较大提升。通过对比可知,Sentinel-2影像拥有较多的光谱波段及适中的空间分辨率,是最合适的红树林范围提取数据源,而ASTER GDEM数据便于区分红树林和陆生植被,是比较好的辅助数据。通过对多源遥感影像及辅助数据提取红树林范围进行对比分析,为红树林遥感提取数据源选取及红树林提取精度提升提供了参考和借鉴。 相似文献
6.
总悬浮物浓度是海洋的重要水质参数之一,其对水体透明度、水下光场及初级生产力有显著影响,同时对河流入海口与海岸带冲淤变化过程有重要作用。本文基于我国自主研制的SDGSAT-1卫星遥感影像,使用准分析算法（Quasi-Analytical Algorithm,QAA）获取水体固有光学量,并结合2022年4月黄河口区域总悬浮物浓度实测数据,建立水体固有光学量与总悬浮物浓度实测数据的单波段、波段加减、波段比值,以及多波段组合等模型并开展遥感反演,最后将反演结果同实测数据及基于Sentinel-2B影像的总悬浮物浓度反演结果进行对比。研究结果表明：基于SDGSAT-1影像的总悬浮物浓度反演结果在黄河口高浓度区域的决定系数为0.622,均方根误差为7.94 mg/L;基于Sentinel-2B影像的总悬浮物浓度反演结果在黄河口高浓度区域的决定系数为0.589,均方根误差为8.27 mg/L。故在我国近岸海域总悬浮物浓度反演方面,SDGSAT-1影像反演精度与Sentinel-2B影像反演精度相媲美。 相似文献
7.
以内陆水体为观测目标的GF-1影像常规融合方法评价 总被引：1，自引：0，他引：1
内陆水体的研究需要遥感影像具备高空间分辨率和高光谱分辨率,这使得影像的全色（PAN）波段和多光谱（MS）波段之间的融合尤为重要。本文以钱塘江大缺口段为研究对象,采用四种常规融合方法,包括Pan Sharpening（PS）、主成分分析（PCA）、Gram Schmidt（GS）和小波分析（WF）,分别对GF-1影像开展了全色波段和多光谱波段的融合方法评价。研究结果表明,GS融合后的影像效果最好,随后分别是PCA、WF和PS。由于水陆之间反射率信息获取的根本差异,大面积水体的存在会影响到融合影像保留源图像空间和光谱信息的能力。因而,在进行遥感影像融合时,融合方法的选择需要考虑影像中水域面积的分布情况。 相似文献
8.
悬浮物含量及其时空分布是河口海岸环境中关心的热点问题。2016年2月16日,欧洲航天局发射了新一代海洋水色传感器(OLCI),该传感器具有良好的时空及光谱分辨率。本研究结合2017年7月杭州湾同步采样数据,对比了6种大气校正算法和8种悬浮物浓度(TSM)估算模型,遴选和分析了适宜于杭州湾和OLCI数据的大气校正方法和TSM估算模型,验证了OLCI数据二级产品精度和适用性。结果表明:(1)基于紫外光谱的大气校正算法(UVAC)精度最高,同步4个采样点的大气校正平均相对误差(MAPE)分别为34.21%、13.11%、5.92%和20.28%。在除Oa1以外的14个波段的MAPE均值为15.23%,Oa4至Oa10波段的MAPE低于8%;(2)基于Oa16/Oa5的波段比值模型,具有良好的建模(MAPE为16.49%,RMSE为50.92 mg/L)和验证(MAPE为19.08%,RMSE为19.29 mg/L)精度及模型稳健性;(3)基于C2RCC算法的固有光学量和TSM含量产品及OLCI二级TSM含量产品在杭州湾精度较差,不适用于杭州湾TSM和固有光学量遥感监测应用;(4)空间上,TSM在杭州湾中部区域含量较低,在杭州湾南岸和湾口区域含量较高。 相似文献
9.
基于随机森林方法反演墨西哥湾海表盐度 总被引：1，自引：0，他引：1
盐度是表征物理和生物地球化学过程的重要参数之一,光学遥感可满足较高分辨率的监测需要并避免射频干扰问题,为沿海水域的海表盐度研究提供可行的途径。本文基于MODIS-Aqua的412 nm、443 nm、488 nm、555 nm和667 nm波段的遥感反射率(Rrs412、Rrs443、Rrs488、Rrs555、Rrs667)、海表温度以及实测的海表盐度数据构建随机森林模型,基于模型结果分析墨西哥湾海表盐度时空异质性及海表盐度与影响因子(海表温度和遥感反射率)之间的相关关系。研究结果表明:(1)随机森林模型能较准确地反演墨西哥湾海表盐度,其均方根误差为0.335,决定系数为0.931;(2)湾区海表盐度空间分布呈近岸?河口低、离岸高,环状向内增值的态势,其变化受河流流量、风力以及环流的影响;(3)海表温度与海表盐度存在较强的相关性,海表温度对海表盐度的反演影响显著;(4)海表温度、遥感反射率与海表盐度的相关性呈现空间异质性。 相似文献
10.
空间分辨率对水深遥感反演的影响分析 总被引：2，自引：0，他引：2
遥感水深反演中空间分辨率的影响是一个重要的科学问题。本文使用东岛的QuickBird和WorldView-2多光谱影像及实测水深点进行实验研究,实验使用了原始空间分辨率（2.4/2m）以及4种降空间分辨率（4m,8m,16m和32m）的影像,使用相同的水深控制点开展水深遥感反演,并对水深反演结果使用相同的检查点进行精度验证。实验结果表明,随着空间分辨率由2.4/2m降低至4m,8m和16m,水深遥感反演的精度呈现出逐渐提高的趋势,进一步降低空间分辨率则会导致水深反演精度下降。当影像空间分辨率为16m时,水深反演结果误差最小且与实测水深值相关性最高,此时两景影像的水深反演平均相对误差分别21.2%和13.1%,相对于最大值分别降低了14.7%和2.9%;平均绝对误差分别为2.0m和1.4m,相对于最大值分别降低了1.0m和0.5m。本文研究结果为水深遥感反演研究与应用中遥感数据的选择提供了参考。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
19.
20.
《海洋学报(英文版)》2014,(11):161-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology, 相似文献