共查询到20条相似文献，搜索用时 15 毫秒
1.
《Applied Ocean Research》2007,29(1-2):1-16
Offshore structures are exposed to random wave loading in the ocean environment and hence the probability distribution of the extreme values of their response to wave loading is of great value in the design of these structures. Wave loading on slender members of bottom-supported jacket or jack-up structures is frequently calculated by Morison’s equation. Due to nonlinearity of the drag component of Morison wave loading and also due to intermittency of wave loading on members in the splash zone, the response is often non-Gaussian; therefore, simple techniques for derivation of their extreme response probability distribution are not available. Finite-memory nonlinear systems (FMNS) are extensively used in establishing a simple relationship between the output and input of complicated nonlinear systems. In this paper, it will be shown how the response of an offshore structure exposed to Morison wave loading can be approximated by the response of an equivalent finite-memory nonlinear system. The approximate models can then be used to determine the probability distribution of response extreme values with great efficiency. Part I of this paper is devoted to the development of an efficient FMNS model for offshore structural response while part II is devoted to the validation of the developed models. 相似文献
2.
The spectral properties of nonlinear drag forces of random waves on vertical circular cylinders are analyzed in this paper by means of nonlinear spectral analysis. The analysis provides basic parameters for estimation of the characteristic drag forces. Numerical computation is also performed for the investigation of the effects of nonlinearity of the drag forces.The results indicate that the wave drag forces calculated by linear wave theory are larger than those calculated by the third order Stokes wave theory for given waves. The difference between them increases with wave height. The wave drag forces calculated by use of hnear approximation are about 5% smaller than their actual values when measured in the peak values of spectral densities. This will result in a safety problem for the design of offshore structures. Therefore, the nonlinear effect of wave drag forces should be taken into comidemtion in design and application of important offshore structures. 相似文献
3.
基于柔性杆理论和尾流振子模型计算陡波形立管的涡激振动响应;综合使用S-N曲线法、雨流计数法、Palmgren-Miner线性累积疲劳理论对立管涡激振动导致的疲劳损伤进行计算分析。并以MATLAB为平台编写相应计算程序,将本文计算得到的静力分析结果、固有频率和疲劳损伤分别与专业海工计算软件OrcaFlex和已发表文献进行对比验证。进一步对陡波形立管在涡激振动下的疲劳损伤进行参数敏感性分析,结果表明:浮子段长度、浮力因子、弹性模量、海流速度、波浪高度对陡波形立管疲劳损伤均有较大影响,有望为陡波形立管的实际工程设计提供参考。 相似文献
4.
Based on the second-order random wave theory, the joint statistical distribution of the horizontal velocity and acceleration is derived using the characteristic function expansion method. From the joint distribution and the Morison equation, the theoretical distributions of drag forces, inertia forces and total random wave forces are determined. The distribution of inertia forces is Gaussian as that derived using the linear wave model, whereas the distributions of drag forces and total random forces deviate slightly from those derived utilizing the linear wave model. It is found that the distribution of wave forces depends solely on the frequency spectrum of sea waves associated with the first order approximation and the second order wave–wave interaction. 相似文献
5.
Subrata K. Chakrabarti 《Ocean Engineering》1989,16(4)
The design and performance of an offshore structure depends largely upon the response of the structure to the environmental loading such as waves. The extreme response chosen for the design of a structure should meet its lifetime response, operational response as well as the fatigue damage. The failure of the structural member may be caused by the maximum instantaneous stress experienced by the member due to a given environment. This is considered short-term as opposed to long-term or fatigue damage. The short-term response statistics are obtained on the basis of one particular seastate. Since this seastate is invariably high, nonlinearity in the excitation and response of the structure is almost invariably present. The general nonlinear problem in the extreme response prediction is largely unsolved. Response characteristics are often obtained from the perturbation methods and equivalent linearization techniques. Unlike nonlinear problems, these methods greatly simplify the analysis for extreme values. This paper reviews the available approximation techniques in the response computation and the limits of their applicability in a design situation. Results are illustrated so that a designer may evaluate the suitability of a method in a particular design condition. 相似文献
6.
For subsea pipeline projects, the costs related to seabed correction and free span intervention are often considerable. Development of reliable methods for fatigue analyses of pipelines in free spans contributes to minimize costs without compromising pipeline integrity. Assessment of wave-induced fatigue damage on multi-span pipelines is investigated, and improved analysis methods are suggested in this paper. A time-domain (TD) algorithm is developed, which accounts for non-linear hydrodynamic loading and dynamic interaction between adjacent spans. The proposed TD approach is employed to evaluate linearized frequency-domain (FD) solutions from recognized design standards and to study the dynamic response of multi-span pipelines to direct wave loading. Differences between multi- and single-span analyses are described for the first time, and the common assumption that the main fatigue damage contribution comes from the fundamental mode is demonstrated not to hold for multi-spans. An improved FD solution capable of predicting multi-mode response is derived and demonstrated to give accurate fatigue life estimates for multi-span pipelines. 相似文献
7.
《Applied Ocean Research》2007,29(1-2):45-54
Catenary mooring lines are typically subjected to bimodal loads, comprising of a wave frequency (WF) component due to the first-order wave forces and a low frequency (LF) component induced by the second-order wave forces. For moored vessels, the LF forces due to current and wind also play a role. Only dynamic wave loads are considered herein, while current and wind loads are modeled as constant forces. Because of the nonlinearities of the mooring line characteristics, the dynamic line tension and the second-order responses, both the WF and LF line tensions are in principle nonGaussian. These facts make it difficult to estimate the combined fatigue damage of mooring lines in the frequency domain. A fatigue combination rule based on the Jiao and Moan’s theory has been extended to cover the nonGaussian case. The purpose of this paper is to improve and validate the frequency-domain method by time-domain analysis based on a simplified, but accurate mechanical model of the dynamic line tension. Improvements on the LF and combined fatigue damage estimation have been made by considering the nonsymmetrical property of the LF line tension distribution. Both the WF and LF mooring line tensions due to wave loading have been simulated in the time domain for different sea states and the combined fatigue damage has been estimated by using the rainflow cycle counting algorithm. The accuracy of the frequency-domain method for estimating the bimodal nonGaussian fatigue damage of mooring lines has been verified by the time-domain simulations and is considered to be acceptable. 相似文献
8.
Floating wind turbine has been the highlight in offshore wind industry lately. There has been great effort on developing highly sophisticated numerical model to better understand its hydrodynamic behaviour. A engineering-practical method to study the nonlinear wave effects on floating wind turbine has been recently developed. Based on the method established, the focus of this paper is to quantify the wave nonlinearity effect due to nonlinear wave kinematics by comparing the structural responses of floating wind turbine when exposed to irregular linear Airy wave and fully nonlinear wave. Critical responses and fatigue damage are studied in operational conditions and short-term extreme values are predicted in extreme conditions respectively. In the operational condition, wind effects are dominating the mean value and standard deviation of most responses except floater heave motion. The fatigue damage at the tower base is dominated by wind effects. The fatigue damage for the mooring line is more influenced by wind effects for conditions with small wave and wave effects for conditions with large wave. The wave nonlinearity effect becomes significant for surge and mooring line tension for large waves while floater heave, pitch motion, tower base bending moment and pontoon axial force are less sensitive to the nonlinear wave effect. In the extreme condition, linear wave theory underestimates wave elevation, floater surge motion and mooring line tension compared with fully nonlinear wave theory while quite close results are predicted for other responses. 相似文献
9.
Ingo Drummen MingKang Wu Miroslaw Lech Kaminski Torgeir Moan 《Ocean Engineering》2009,36(15-16):1208-1216
Previous studies of response conditioned wave methods have been focused on their applicability to the prediction of extreme nonlinear wave-induced load effects. The results showed that theses methods can be used to accurately and efficiently predict the nonlinear short-term probability distributions for rigid hull responses. This has led us to investigate how response conditioned wave methods can be used for long-term nonlinear fatigue analyses, and with which accuracy this can be done. In this paper we present the results from our investigation. The studies were performed using a container vessel with a length between perpendiculars of 281 m. Calculations were done with a nonlinear strip theory method in which the hull of the vessel was assumed to be rigid. The most likely response wave (MLRW) method was used to condition the waves. Only head seas were considered. We found that the MLRW method under-predicted the long-term fatigue damage by 3%. The method, however, required a simulation time that was approximately three orders of magnitude less than that required for a conventional long-term nonlinear analysis based on random irregular waves. A preliminary investigation showed that due to lacking springing and whipping contributions the MLRW method under-predicted the fatigue damage for a flexible hull by approximately 50%. Several comments about a more accurate extension of the proposed method to flexible hulls are included. 相似文献
10.
Modified Gaussian phase distributions are used to generate short time series containing a specific extreme value of a ship response. The corresponding incident wave train is calculated via linear systems theory. Sample response and wave time series are compared to the expected time series as calculated by probabilistic analysis. The average of the sample response time series compares favorably to the expected time series, but the average of the sample wave trains does not, in general, match the expected wave train. These comparisons show the danger in estimating extreme ship responses considering only extreme waves. A sample analysis for a Great Lakes bulk carrier is included for illustration. 相似文献
11.
12.
Based on the second-order solutions obtained for the three-dimensional weakly nonlinear random waves propagating over a steady uniform current in finite water depth, the joint statistical distribution of the velocity and acceleration of the fluid particle in the current direction is derived using the characteristic function expansion method. From the joint distribution and the Morison equation, the theoretical distributions of drag forces, inertia forces and total random forces caused by waves propagating over a steady uniform current are determined. The distribution of inertia forces is Gaussian as that derived using the linear wave model, whereas the distributions of drag forces and total random forces deviate slightly from those derived utilizing the linear wave model. The distributions presented can be determined by the wave number spectrum of ocean waves, current speed and the second order wave–wave and wave–current interactions. As an illustrative example, for fully developed deep ocean waves, the parameters appeared in the distributions near still water level are calculated for various wind speeds and current speeds by using Donelan–Pierson–Banner spectrum and the effects of the current and the nonlinearity of ocean waves on the distribution are studied. 相似文献
13.
The research into hydrodynamic loading on ocean structures has concentrated mostly on circular cross-section members and relatively limited work has been carried out on wave loading on other cross-sections such as rectangular sections. These find applications in many offshore structures as columns and pontoons in semi-submersibles and tension-leg platforms. The present investigation demonstrates the behaviour of rectangular cylinders subject to wave loading and also supplies the hydrodynamic coefficients for the design of these sections.This paper presents the results of wave forces acting on a surface piercing truncated rectangular cylinder set vertically in a towing tank. The experiments are carried out in a water depth of 2.2 m with regular and random waves for low Keulegan–Carpenter number up to 6. The rectangular cylinder is of 2 m length, 0.2 m breadth and 0.4 m width with a submergence depth of 1.45 m from still water level. Based on Morison equation, the relationship between inertia and drag coefficients are evaluated and are presented as a function of KC number for various values of frequency parameter β, for two aspect ratios of cylinders, equals to 1/2 and 2/1. Drag and inertia coefficients obtained through regular wave tests are used for the random wave analysis to compute the in-line force spectrum.The results of the experiments show the drag and inertia coefficients are strongly affected by the variation in the aspect ratios of the cylinder. The drag coefficients decreases and inertia coefficients increases with increase in Keulegan–Carpenter number up to the range of KC number tested. The random wave results show a good correlation between measured and computed force spectrums. The transverse forces in both regular and random waves are found to be small compared to in-line forces. 相似文献
14.
由于沿海区域的限制以及愈加严重的环境污染,渔业养殖正从近海走向深远海。深远海海域的海况更加恶劣,给养殖装备的设计与性能评估带来新的挑战。为解决该问题,对极端波浪与养殖装备网衣结构的相互作用开展研究。基于waves2Foam建立数值波浪水池,极端波浪模拟采用基于NewWave理论的聚焦波模型,网衣结构模拟采用多孔介质模型,并通过与Morison模型计算的网衣受力等效分析,获得多孔介质模拟网衣结构阻力系数的直接估计方法。然后将多孔介质模型嵌入waves2Foam中,开展聚焦波与网衣结构相互作用的数值模拟,同时开展水槽试验,验证数值模拟的准确性。基于数值模拟结果,系统地分析了不同网衣密实度及不同波浪参数下网衣结构的升阻力特性以及网衣结构对波浪场的扰动规律。研究表明：聚焦波波峰幅值和网衣密实度对网衣结构的升阻力影响较大,且升力峰值出现在阻力为0的时刻;网衣结构对聚焦波的时空演化特性有影响,改变了聚焦波波形。 相似文献
15.
A method for stochastic fatigue analysis of offshore platforms is presented. The method accounts for the nonlinearity in the drag loading term, and for the systematic deviation from a Gaussian process for a platform response. The method is based on an assumed form of the stress response process at a hot spot. A number of full scale measurements for elements in fixed platforms and for marine risers show very good agreement with this assumed form. A conventional spectral fatigue approach with stochastic linearization of the drag term in the basis for the new method, which uses results from linearizations in two or more sea states. The method is easily implemented in standard computer programs presently used within the offshore oil industry for fatigue analysis. 相似文献
16.
研究浅水半潜式大功率浮式风力机波浪载荷和气动力引起的基础结构疲劳损伤,揭示基础结构的疲劳损伤机理。采用谱疲劳损伤计算分析方法,以10 MW风力机为例,计算波浪载荷引起的热点应力及多种海况引起的疲劳损伤。采用叶素动量理论并基于所在海域的风速分布,计算叶轮转动引起的气动力及其引起的疲劳损伤。计算结果表明,对于半潜式三立柱浮式风力机,波浪载荷引起的基础结构应力远大于气动力引起的基础结构应力,基础结构损伤主要是由波浪载荷引起,气动力引起的浮式基础结构的损伤为10-3量级,而波浪载荷引起的损伤为10-1量级。 相似文献
17.
Since offshore towers are high-cost, high-risk structures, reliability analysis is of great importance in their design. This paper presents a possible practical approach to certify a design through selective critical member reliability estimates. After a brief review of current research in this field, the authors outline a procedure for reliability estimation of structural members in extreme stress and fatigue limit states. A spectral approach for the extreme response statistics with stochastic loading is described. The reliabilities are computed by the Level II first-order second moment (advanced) method. The fatigue reliability is estimated with a narrow-banded stress assumption with discrete, but significant sea states within the life of the structure. Two numerical examples, a three shallow water model and a two-dimensional deep water model are presented along with the influences of stochastic variables (sea state, current, tubular member diameter) on reliabilities (extreme stress and fatigue damage). 相似文献
18.
《Coastal Engineering》1987,11(3):189-218
Forces on a smooth submarine pipeline, fixed horizontally near a plane boundary, have been investigated under random wave conditions. The submarine pipeline was subjected to Pierson-Moskowitz spectrum (P-M spectrum) at various energy levels. The water particle kinematics were computed based on the linear random wave model and the Morison equation was chosen as the wave force predictor model. The inline hydrodynamic coefficients of drag and inertia were evaluated using two different methods, one in the frequency domain and the other in the time domain. Five mathematical formulations were considered for the analysis of transverse wave forces and these were compared in terms of the correlation coefficient. The transverse force was also analyzed in terms of the transverse root mean square (rms) coefficient. The inline hydrodynamic coefficients of drag and inertia and the transverse rms coefficient were correlated with the Keulegan-Carpenter number or period parameter, the relative clearance of the pipeline from the bed and the depth parameter. Finally, the results of the random wave tests were compared with those of regular waves under similar pipeline conditions. 相似文献
19.
Dynamic and static analysis of a marine riser 总被引：1，自引：0，他引：1
A frequency domain normal mode solution is presented for the dynamic response of an unbuoyed marine riser subjected to periodic excitation from a surface vessel in the direction of wave propagation. The variable tension beam-column equation is solved in terms of normal modes of free vibration of the riser and the rigid body displacement. Drag forces on the riser are represented by Morison's formula taking account of the velocity of the riser and wave-induced fluid velocity. A periodic solution for the flexural motion of the riser and the bending stress is then obtained by means of an iterative solution of the frequency response function. The drag force induced stresses arising from a linearly varying current are also determined. The results presented compare favourably with those obtained by other methods. 相似文献
20.
应用非线性谱分析理论，对三阶Stokes型随机波浪载荷谱进行了分析，将波面方程及海水质点的水平速度用一阶波面的非线性组表示，导出了随机波浪谱的表达式。为了便于求解随机波浪的载荷谱，将阻力项展开为幂级数式，并应用非线性谱分析理论，确定了幂级数的系数，进而将波浪载荷表示为一阶波面及其导数的非线性组合，最后得出波浪载荷谱密度的表达式，并应用数值分析方法，得出单位桩柱波浪力及总波浪力谱密度。 相似文献