共查询到20条相似文献，搜索用时 890 毫秒
1.
Sediment dynamics below retreating cliffs 总被引：1，自引：0，他引：1
The retreat of cliffs may constitute the dominant erosional response to base‐level fall in arid settings underlain by horizontally‐bedded sedimentary rock. These vertical cliffs typically loom above a relatively straight bedrock slope (‘plinth’) that is mantled with a thin layer of sediment and perched near the angle of repose. In detail, a plinth consists of a system of quasi‐parallel ridges and channels. We ask how the sediment supplied from a retreating cliff influences the erosion of the plinth hillslopes and channels, and how this affects the rate of cliff retreat. Motivated by field observations and high‐resolution topographic data from two sites in western Colorado, we develop a two‐dimensional (2D), rules‐based numerical model to simulate the erosion of channels draining a plinth and diffusive erosion of the intervening interfluves. In this model, retreat of a cliffband occurs when the height of the vertical cliff exceeds a threshold due to incision by channels on the plinth below. Debris derived from cliff retreat is distributed over the model plinth according to the local topography and distance from the source. This debris then weathers in place, and importantly can act to reduce local bedrock erosion rates, protecting both the plinth and ultimately the cliff from erosion. In this paper, we focus on two sets of numerical model experiments. In one suite, we regulate the rate of rockfall to limit the cliff retreat rate; in most cases, this results in complete loss of the plinth by erosion. In a second suite, we do not impose a limit on the cliff retreat rate, but instead vary the weathering rate of the rockfall debris. These runs result in temporally steady cliff‐plinth forms and retreat rates; both depend on the weathering rate of the debris. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
2.
Mark Grasmueck Miquel Coll Quintà Kenri Pomar Gregor P. Eberli 《Geophysical Prospecting》2013,61(5):907-918
Vertical fractures with openings of less than one centimetre and irregular karst cause abundant diffractions in Ground‐Penetrating Radar (GPR) records. GPR data acquired with half‐wavelength trace spacing are uninterpretable as they are dominated by spatially undersampled scattered energy. To evaluate the potential of high‐density 3D GPR diffraction imaging a 200 MHz survey with less than a quarter wavelength grid spacing (0.05 m × 0.1 m) was acquired at a fractured and karstified limestone quarry near the village of Cassis in Southern France. After 3D migration processing, diffraction apices line up in sub‐vertical fracture planes and cluster in locations of karstic dissolution features. The majority of karst is developed at intersections of two or more fractures and is limited in depth by a stratigraphic boundary. Such high‐resolution 3D GPR imaging offers an unprecedented internal view of a complex fractured carbonate reservoir model analogue. As seismic and GPR wave kinematics are similar, improvements in the imaging of steep fractures and irregular voids at the resolution limit can also be expected from high‐density seismic diffraction imaging. 相似文献
3.
4.
《中国地震研究》2021,(2)
Natural fractures are widely distributed in shale reservoirs. During the hydraulic fracturing process, frictional slip occurring on natural fractures can increase the reservoir permeability and is of great significance to improve the efficiency of reservoir stimulation. Shale contains a large amount of clay and organic matter, and its frictional behavior is different from that of other previously studied lithologies. In this paper, the frictional behavior of shale is analyzed, and the results show that the frictional behavior is controlled by the content of clay and organic matter. As the content of clay and organic matter increases, the micro support type transforms from the particle support mode by hard quartz mineral to matrix support mode by plastic clay and organic matter. Accordingly, the shear strength and friction coefficient of shale both decrease, and the shear type transforms from brittle to plastic.When the content of clay and organic matter is low, the asperity of friction surfaces will break in a brittle manner and the wear degree of surfaces is low. Therefore, fractures are still featured by moderate apertures after friction.The lower the content of clay and organic matter is, the easier the asperity of crack surfaces supports themselves,and the higher the fracture residual permeability is. Thus, promoting shear slip is the main measure of reservoir stimulation. However, when the content of clay and organic matter is high, the remaining post-slip fracture aperture is small. It is difficult to increase reservoir permeability through the frictional slip of natural fractures,and in this situation, the proppant support efficiency needs to be improved. 相似文献
5.
Jesus A. Uriarte Laura Damas Mollá Maialen Sagarna Arantza Aranburu Francisco García Iñaki Antigüedad Tomás Morales 《水文研究》2020,34(4):1004-1015
Locating and quantifying groundwater flow in many built-up areas are a priority with regard to its complete restoration. In this work, a hydrogeological survey of the surroundings of the Punta Begoña Galleries (Getxo, Bizkaia), built on a coastal cliff, was completed by using ground penetrating radar (GPR) testing. Thus, the preliminary characterization of soils and rocks in accessible areas of the cliff was first improved by hydrogeological information gathered from a single survey borehole, including permeability measurements by low pressure injection tests (LPTs) and continuous water level monitoring. As a complementary method, the non-destructive GPR technique was performed during both dry and wet hydrological periods and in tandem with the injection tests, providing more complete spatial and temporal images of water flows. Specifically, GPR allows mapping of flow paths in soils and assessing the continuity of fractures in rock masses. Altogether, this complementary approach provides greater knowledge of complex underground flow dynamics in built environments, thus making it easier to make decisions for their management. 相似文献
6.
《Advances in water resources》2004,27(6):583-599
Methods for estimating the parameter distributions necessary for modeling fluid flow and contaminant transport in the shallow subsurface are in great demand. Soil properties such as permeability, porosity, and water retention are typically estimated through the inversion of hydrological data (e.g., measurements of capillary pressure and water saturation). However, ill-posedness and non-uniqueness commonly arise in such non-linear inverse problems making their solutions elusive. Incorporating additional types of data, such as from geophysical methods, may greatly improve the success of inverse modeling. In particular, ground-penetrating radar (GPR) methods have proven sensitive to subsurface fluid flow processes and appear promising for such applications. In the present work, an inverse technique is presented which allows for the estimation of flow parameter distributions and the prediction of flow phenomena using GPR and hydrological measurements collected during a transient flow experiment. Specifically, concepts from the pilot point method were implemented in a maximum a posteriori (MAP) framework to allow for the generation of permeability distributions that are conditional to permeability point measurements, that maintain specified patterns of spatial correlation, and that are consistent with geophysical and hydrological data. The current implementation of the approach allows for additional flow parameters to be estimated concurrently if they are assumed uniform and uncorrelated with the permeability distribution. (The method itself allows for heterogeneity in these parameters to be considered, and it allows for parameters of the petrophysical and semivariogram models to be estimated as well.) Through a synthetic example, performance of the method is evaluated under various conditions, and some conclusions are made regarding the joint use of transient GPR and hydrological measurements in estimating fluid flow parameters in the vadose zone. 相似文献
7.
8.
准噶尔盆地腹部侏罗系以隐蔽油气藏为主,地震资料在目的层分辨率较低、地震反射特征不清晰,制约了对该区的低幅构造、岩性圈闭的识别和评价.本文根据侏罗系的沉积特点,建立河流、（扇）三角洲沉积体系地质模型,制作尖灭体、透镜体、河道砂、浊积体等地质体的三维物理模型,通过实验测试方法,研究地层条件下岩石物理性质的变化特征,系统研究储层地球物理参数变化的总体规律,并结合测井资料,采用波场物理模拟方法,研究波场响应特征与储层参数变化之间的规律,分析各种情况下的波场特征、属性特征. 相似文献
9.
We measured in the laboratory ultrasonic compressional and shear‐wave velocity and attenuation (0.7–1.0 MHz) and low‐frequency (2 Hz) electrical resistivity on 63 sandstone samples with a wide range of petrophysical properties to study the influence of reservoir porosity, permeability and clay content on the joint elastic‐electrical properties of reservoir sandstones. P‐ and S‐wave velocities were found to be linearly correlated with apparent electrical formation factor on a semi‐logarithmic scale for both clean and clay‐rich sandstones; P‐ and S‐wave attenuations showed a bell‐shaped correlation (partial for S‐waves) with apparent electrical formation factor. The joint elastic‐electrical properties provide a way to discriminate between sandstones with similar porosities but with different clay contents. The laboratory results can be used to estimate sandstone reservoir permeability from seismic velocity and apparent formation factor obtained from co‐located seismic and controlled source electromagnetic surveys. 相似文献
10.
The shape and location of clay within sandstones have a large impact on the P‐wave and S‐wave velocities of the rock. They also have a large effect on reservoir properties and the interpretation of those properties from seismic data and well logs. Numerical models of different distributions of clay – structural, laminar and dispersed clay – can lead to an understanding of these effects. Clay which is located between quartz grains, structural clay, will reduce the P‐wave and S‐wave velocities of the rock. If the clay particles become aligned or form layers, the velocities perpendicular to the alignment will be reduced further. S‐wave velocities decrease more rapidly than P‐wave velocities with increasing clay content, and therefore Poisson's ratios will increase as the velocities decrease. These effects are more pronounced for compacted sandstones. Small amounts of clay that are located in the pore space will have little effect on the P‐wave velocity due to the competing influence of the density effect and pore‐fluid stiffening. The S‐wave velocity will decrease due to the density effect and thus the Poisson's ratio will increase. When there is sufficient clay to bridge the gaps between the quartz grains, P‐wave and S‐wave velocities rise rapidly and the Poisson's ratios decrease. These effects are more pronounced for under‐compacted sandstones. These general results are only slightly modified when the intrinsic anisotropy of the clay material is taken into account. Numerical models indicate that there is a strong, nearly linear relationship between P‐wave and S‐wave velocity which is almost independent of clay distribution. S‐wave velocities can be predicted reasonably accurately from P‐wave velocities based on empirical relationships. However, this does not provide any connection between the elastic and petrophysical properties of the rocks. Numerical modelling offers this connection but requires the inclusion of clay distribution and anisotropy to provide a model that is consistent with both the elastic and petrophysical properties. If clay distribution is ignored, predicting porosities from P‐wave or S‐wave data, for example, can result in large errors. Estimation of the clay distribution from P‐wave and S‐wave velocities requires good estimates of the porosity and clay volume and verification from petrographic analyses of core or cuttings. For a real data example, numerical models of the elastic properties suggest the predominance of dispersed clay in a fluvial sand from matching P‐wave and S‐wave velocity well log data using log‐based estimates of the clay volume and porosity. This is consistent with an interpretation of other log data. 相似文献
11.
Combined time‐lapse reservoir simulation and seismic modelling has been performed on both 1D and 3D models of a channelized turbidite reservoir. The models have been built using core, log, laboratory and seismic data from the Nelson Field (central North Sea) as a template. Oil and water movement in the main channels, channel margins and interchannel regions is investigated, with a particular focus being the effect of poor net‐to‐gross. The analysis confirms that saturation effects dominate the response whilst stress‐sensitivity effects play a minor role. The trough–peak signature in the seismic difference volumes formed by the sweep of the water can be continued and mapped slightly further than the channel margins. This characteristic 4D signature remains roughly intact, despite the complicated depositional architecture, and accurately delineates the area of moved fluid, but it needs additional calibration to combat the detrimental influence of the low net‐to‐gross. Signal strength is largely dependent on reservoir quality, but is also compromised by the net‐to‐gross, fluid distribution and, more critically, by the exact timing of the seismic survey. For example, a region of bypassed oil zone remains undetected as it forms early during the production. This work demonstrates that to understand fully the 4D signature at a quantitative level requires adequate knowledge of the fluid properties, but also, more critically, the geology. 相似文献
12.
Antidunes and their sedimentary structures can be useful in reconstructing paleo‐hydraulic conditions, especially for large discharge events. However, three‐dimensional (3D) antidunes in sand‐sized sediments have not yet been studied extensively, as compared to either two‐dimensional (2D) antidunes or antidunes in gravel‐sized sediments. In this study, we estimated formative conditions of gravel step‐pool morphologies and applied them to the formation of 3D antidunes over a sand bed. Formative conditions are expressed in terms of a relationship between the water discharge per unit width and the bed slope. Flume experiments demonstrated that 3D mound‐like antidune configurations and their associated internal sedimentary structures could be preserved. Internal sedimentary structures were characterized by shallow lens‐like structures whose bases were erosional. Although gently‐dipping concave‐upward lamination was dominant, convex‐upward lamination was occasionally observed. The dimensions of lenticular lamina‐sets can be used to estimate antidune geometry. Thus if 3D antidunes can be interpreted in the stratigraphic record, it is possible to estimate the paleo‐hydraulic parameters such as water discharge and bed slope more precisely than previously. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
13.
液相渗透率描述了岩石的渗流特性,是评价储层与预测油气产能的重要参数.液相渗透率是指盐水溶液在岩石孔隙中流动且与岩石孔隙表面黏土矿物发生物理化学作用时所测得的渗透率;液相渗透率的实验测量条件更加接近实际地层泥质砂岩的条件,使得液相渗透率更能反映地层条件下泥质砂岩的渗流特性;然而,现有的液相渗透率评价模型较少,且模型未能揭示液相渗透率与溶液矿化度之间的关系.基于此,开展了液相渗透模型推导与计算方法研究;文中首先将岩石等效为毛管束模型,推导建立了液相渗透率与比表面、喉道曲折度、总孔隙度、黏土束缚水孔隙度等参数之间的关系;其次,根据岩石物理体积模型,推导建立了黏土束缚水孔隙度与阳离子交换容量、溶液矿化度等参数的关系;最终,将黏土束缚水孔隙度引入液相渗透率计算公式,建立了基于总孔隙度、阳离子交换容量、溶液矿化度、比表面、喉道曲折度等参数的液相渗透率理论计算模型.液相渗透率计算模型与两组实验数据均表明,液相渗透率随阳离子交换容量的增大而降低,随溶液矿化度的增大而增大.然而,液相渗透率理论计算模型的实际应用中喉道曲折度、比表面等参数求取困难,直接利用理论模型计算液相渗透率受到限制.在分析液相渗透率与孔隙渗透率模型的基础上,建立了液相渗透率与空气渗透率之间的转换模型,形成了利用转化模型计算液相渗透率的新方法.为进一步验证液相渗透率与空气渗透率转化模型的准确性,基于两组实验数据,利用转换模型计算了液相渗透率;液相渗透率计算结果与岩心测量液相渗透率实验结果对比显示,液相渗透率计算结果与实际岩心测量结果吻合较好,文中建立的液相渗透率与空气渗透率转化模型合理可靠. 相似文献
14.
Paleokarst system development in the San Andres Formation, Permian Basin, revealed by seismic characterization 总被引：1，自引：0，他引：1
Paleokarst systems are one of the major factors resulting in carbonate reservoir heterogeneity and compartmentalization. Nevertheless, few effective workflows have been proposed to map the 3D distribution of such systems. We describe a detailed seismic characterization approach integrating core, well log and rock physics analysis, to reveal a complex subsurface paleokarst system in the San Andres Formation, Permian basin, West Texas. In the area of high volume production, the collapsed paleokarst system is characterized by irregularly developed crackle and fracture breccias, mosaic breccias and cave fillings in the Upper San Andres Formation, which are delineated using seismic acoustic impedance. Along the transition from platform to basin, the paleokarst system is marked by a linear collapse including sags and small vertical faults that are recognizable in seismic imaging. Production data indicates that tight paleokarst zones cause reservoir compartmentalization and influence fluid communication between wells. The complex paleokarst system development is explained using a carbonate platform hydrological model, an outcrop analogue similar to modern marine hydrological environments within carbonate islands. Our method of model development for complex subsurface paleokarst systems may be applicable to other paleoenvironments. 相似文献
15.
Numerous examples of reservoir fields from continental and marine environments involve thin‐bedded geology, yet, the inter‐relationship between thin‐bedded geology, fluid flow and seismic wave propagation is poorly understood. In this paper, we explore the 4D seismic signature due to saturation changes of gas within thin layers, and address the challenge of identifying the relevant scales and properties, which correctly define the geology, fluid flow and seismic wave propagation in the field. Based on the study of an outcrop analogue for a thin‐bedded turbidite, we model the time‐lapse seismic response to fluid saturation changes for different levels of model scale, and explore discrepancies in quantitative seismic attributes caused by upscaling. Our model reflects the geological complexity associated with thin‐bedded turbidites, and its coupling to fluid flow, which in turn affects the gas saturation distribution in space, and its time‐lapse seismic imprint. Rock matrix and fluid properties are modelled after selected fields to reproduce representative field models with realistic impedance contrasts. In addition, seismic modelling includes multiples, in order to assess their contribution in seismic propagation through thin gas layers. Our results show that multiples could contribute significantly to the measured amplitudes in the case of thin‐bedded geology. This suggests that forward/inverse modelling involving the flow simulation and seismic domains used in time‐lapse seismic interpretation should account for thin layers, when these are present in the geological setting. 相似文献
16.
P‐wave data from a time‐lapse 3D OBC survey have been analysed to estimate and interpret azimuthal seismic anisotropy. This is achieved by careful processing to preserve the azimuthal signature. The survey images a major reservoir body in a channelized turbidite field in the Gulf of Mexico. Three distinct and significant anisotropy anomalies are discovered on or around this particular ‘4500‐ft sand’, all of which change intensity but not orientation with hydrocarbon production. These anomalies are distributed along the highest concentration of cumulative sand thickness, with their symmetry axes aligned with the main channel axis. We suspect that this time‐lapse anisotropy could be caused by the alignment of the depositional grain fabric. Theoretical calculation predicts that this mechanism, when combined with fluid‐saturation changes, can generate the observed pattern of behaviour. If further supported by other researchers, this result would indicate that appropriately designed seismic surveys could be a useful tool for palaeo‐direction studies in clastic reservoirs and also a useful constraint for directional permeability in the reservoir flow simulation model. 相似文献
17.
Photographing layer thicknesses and discontinuities in a marble quarry with 3D GPR visualisation 总被引：1，自引：0，他引：1
An important problem of marble-quarry management is assessing the quality and the homogeneity of quarry blocks before excavation. In this study, we decided to image the limestone, which we studied in a marble quarry, in terms of layer thickness, discontinuities and cavities using the ground-penetrating-radar (GPR) method. The method was successfully applied to detect and map the fractures with the cavities in a marble layer according to depth in the Ankara City Polatli Town (Turkey) region, which represents upper Miocene–Pliocene lacustrine carbonate rocks.This paper is based on interactive transparent 3D visualisation of the 2D GPR profiles to determine changes in layer thickness and discontinuities. In addition, this paper indicates the importance of the appropriate opacity-function construction to obtain transparent 3D visualisation. Firstly we acquired and processed parallel 2D GPR profile data, then we assigned two different amplitude–colour ranges using a limited number of colours to determine the layer thickness and its discontinuities separately. We obtained a 3D volume using parallel 2D GPR data and displayed a limited amplitude range by arranging an opacity function. Therefore, we obtained transparent 3D blocks for thickness and discontinuities, and we formulated an interactive 3D display to image the horizontal, vertical and inclined discontinuities and their directions in the x–y plane versus depth. The GPR results were compared with the petrographical investigation on the basis of textural and mineralogical compositions. The vesicular textures within carbonate platform were supported by the GPR results. 相似文献
18.
Quantitative characterization of reservoir space in the Lower Silurian Longmaxi Shale,southern Sichuan,China 总被引：1，自引：0，他引：1
WANG YuMan DONG DaZhong YANG Hua HE Ling WANG ShiQian HUANG JinLiang PU BoLing WANG ShuFang 《中国科学:地球科学(英文版)》2014,57(2):313-322
Based on the drilling data of the Upper Ordovician Wufeng Shale and the Lower Silurian Longmaxi Shale in southern Sichuan Basin,the construction of matrix pores and the development condition of fractures in a marine organic-rich shale are quantitatively evaluated through the establishment of the reservoir petrophysical models and porosity mathematical models.Our studies show that there are four major characteristics of the Longmaxi Shale confirmed by the quantitative characterization:(1)the pore volume of per unit mass is the highest in organic matter,followed in clay minerals,finally in brittle minerals;(2)the porosity of the effective shale reservoir is moderate and equal to that of the Barnett Shale,and the main parts of the shale reservoir spaces are interlayer pores of clay minerals and organic pores;(3)the porosity of the organic-rich shale is closely related to TOC and brittle mineral/clay mineral ratio,and mainly increases with TOC and clay mineral content;(4)fractures are developed in this black shale,and are mainly micro ones and medium-large ones.In the Longmaxi Shale,the fracture density increases from top to bottom,reflecting the characteristics with high brittle mineral content,high Young’s modulus,low Poisson's ratio and high brittleness at its bottom. 相似文献
19.
Two formulae are developed for estimating horizontal permeability directly from maps of 4D seismic signatures. The choice of the formula used depends on whether the seismic is dominated by changes of pressure or saturation. However, pressure derived from time‐lapse seismic, or seismic amplitudes controlled predominantly by pressure are to be preferred for optimal ‘illumination’ of the reservoir. The permeability is predicted to be dependent on porosity but weighted by a 4D term related to the magnitude and spatial gradient of the 4D signature. Tests performed on model‐based synthetic seismic data affirm the validity and accuracy of this approach. Application to field data from the UK continental shelf reveals a large‐scale permeability variation similar to the existing simulation model, but with additional fine‐scale detail. The technique thus has the potential of providing extra information with which to update the simulation model. The resultant permeability estimates have been successfully ground‐truthed against the results of two well tests. As non‐repeatable noise in the time‐lapse seismic data diminishes with improved 4D‐related acquisition, it will become increasingly possible to make robust permeability estimates using this approach. 相似文献
20.
Shiv N. Dasgupta 《Geophysical Prospecting》2005,53(2):215-227
Ghawar, the largest oilfield in the world, produces oil from the Upper Jurassic Arab‐D carbonate reservoir. The high rigidity of the limestone–dolomite reservoir rock matrix and the small contrast between the elastic properties of the pore fluids, i.e. oil and water, are responsible for the weak 4D seismic effect due to oil production. A feasibility study was recently completed to quantify the 4D seismic response of reservoir saturation changes as brine replaced oil. The study consisted of analysing reservoir rock physics, petro‐acoustic data and seismic modelling. A seismic model of flow simulation using fluid substitution concluded that time‐lapse surface seismic or conventional 4D seismic is unlikely to detect the floodfront within the repeatability of surface seismic measurements. Thus, an alternative approach to 4D seismic for reservoir fluid monitoring is proposed. Permanent seismic sensors could be installed in a borehole and on the surface for passive monitoring of microseismic activity from reservoir pore‐pressure perturbations. Reservoir production and injection operations create these pressure or stress perturbations. Reservoir heterogeneities affecting the fluid flow could be mapped by recording the distribution of epicentre locations of these microseisms or small earthquakes. The permanent borehole sensors could also record repeated offset vertical seismic profiling surveys using a surface source at a fixed location to ensure repeatability. The repeated vertical seismic profiling could image the change in reservoir properties with production. 相似文献