首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 312 毫秒
1.
The permeability of coal samples from Pittsburgh Seam was determined using carbon dioxide as the flowing fluid. The confining pressure was varied to cover a wide range of depths. The permeability was determined as a function of exposure time of carbon dioxide while the confining stress was kept constant. The porosities of the coal samples were found to be very low and most of the samples had porosities less than 1%. The permeability of these coal samples was very low—less than 1 μD. Since the objective of this study was to investigate the influence of CO2 exposure on coal permeability, it was necessary to increase the initial permeability of the coal samples by introducing a fracture. A longitudinal fracture was induced mechanically, and CT scans were taken to ensure that the fracture was present throughout the sample and that the sample was not damaged otherwise during the process. In this study, the permeability of coal was determined by using pressure transient methods. Two types of pressure pulses were used: A-spike and Sine-6 pressure transients. It was first established that the permeability of fractured coal samples did not change with exposure time when an inert gas (Argon) was used as the fluid medium in the experiments. However, the permeability of coal samples decreased significantly when carbon dioxide was used as the fluid medium. This reduction can be attributed to the coal swelling phenomenon. The results show that the permeability reduction in fractured coal samples can be over 90% of the original value, and the exposure time for such reductions can range from 1.5 days up to a week, typically about 2 days under laboratory conditions. The permeability decreased significantly with the increase in confining pressure. The higher confining pressure appears to close internal fractures causing a reduction in permeability.  相似文献   

2.
Enhanced coalbed methane (ECBM) involves the injection of a gas, such as nitrogen or carbon dioxide, into the coal reservoir to displace the methane present. Potentially this strategy can offer greater recovery of the coal seam methane and higher rates of recovery due to pressure maintenance of the reservoir. While reservoir simulation forms an important part of the planning and assessment of ECBM, a key question is the accuracy of existing approaches to characterising and representing the gas migration process. Laboratory core flooding allows the gas displacement process to be investigated on intact coal core samples under conditions analogous to those in the reservoir. In this paper a series of enhanced drainage core floods are presented and history matched using an established coal seam gas reservoir simulator, SIMED II. The core floods were performed at two pore pressures, 2 MPa and 10 MPa, and involve either nitrogen or flue gas (90% nitrogen and 10% CO2) flooding of core samples initially saturated with methane. At the end of the nitrogen floods the core flood was reversed by flooding with methane to investigate the potential for hysteresis in the gas displacement process. Prior to the core flooding an independent characterisation programme was performed on the core sample where the adsorption isotherm, swelling with gas adsorption, cleat compressibility and geomechanical properties were measured. This information was used in the history matching of the core floods; the properties adjusted in the history matching were related to the affect of sorption strain on coal permeability and the transfer of gas between cleat and matrix. Excellent agreement was obtained between simulated and observed gas rates, breakthrough times and total mass balances for the nitrogen/methane floods. It was found that a triple porosity model improved the agreement with observed gas migration over the standard dual porosity Warren-Root model. The Connell, Lu and Pan hydrostatic permeability model was used in the simulations and improved history match results by representing the contrast between pore and bulk sorption strains for the 10 MPa cases but this effect was not apparent for the 2 MPa cases. There were significant differences between the simulations and observations for CO2 flow rates and mass balances for the flue gas core floods. A possible explanation for these results could be that there may be inaccuracy in the representation of mixed gas adsorption using the extended Langmuir adsorption model.  相似文献   

3.
Sorption of methane on lignite from Polish deposits   总被引：1，自引：0，他引：1  
Coal samples from Miocene lignite deposits (ortholignite—ECE-UN 2002) in Belchatow, Adamow, Konin and Turow (Poland) were analyzed to determine the relationships between coal properties and gas capacity.Investigations presented here addressed the occurrence of methane sorbet in lignite deposits within Poland's largest penetrated lignite deposits (e.g., Belchatow, Adamow, Turow and Konin).Lignite samples collected from surface mines were detritic coal with variable contents of xylites. The highest level of xylites (up to 25 vol.%) was found in carbon samples taken from the Belchatow deposit. Samples from other mines contained no more than 10 vol.% xylites. Petrographic compositions were dominated by huminite group macerals (73-88 vol.%) with atrinite, densinite and texto-ulminite, a porous form of ulminite; inertinite groups were less important components (4-8 vol.%).Isotherms were determined for methane sorption at 298 K with test pressure ranges below 1.2 MPa. At a pressure of 1.0 MPa, the largest gas capacity of approximately 1.7 [dm3 STP/kg] was found in the sample from Belchatow. This result may have been attributable to differences in the porosity of the samples; the porosity of the sample from Belchatow was twice as high as the porosities of the other coal samples. This variation in porosity resulted from the lithologic and maceral composition of the coal sample that contained substantial quantities of porous textinite and texto-ulminite.The thermal sorption equation was used to determine the limiting values of isosteric enthalpy of sorption, which suggested weak interactions between methane and the lignite matrix. The residual gas capacity of the tested samples was also determined.All samples exhibited a high residual methane-bearing capacity, which may not only cause methane to be released from coal at a pressure of 1 bar but also may pose a gas risk during mining operations.  相似文献   

4.
王伟  方志明  李小春 《岩土力学》2018,39(Z1):251-257
为研究沁水盆地煤样渗透率演化规律,构建了煤样渗透率测定的瞬态压力脉冲法实验装置,使用N2和CO2在实验室开展了3种试验条件的渗透率测定,应用Connell模型对实验结果进行分析,并讨论了模型预测值和实验值之间差别的原因。结果表明,（1）在恒定孔压变围压条件下渗透率随有效应力增大而减小;在等有效应力条件下,渗透率随孔压增大而减少;在恒定围压变孔压条件下,随孔压增大,渗透率呈先减小后变大的趋势。（2）运用Connell模型预测的恒定围压变孔压条件的渗透率值大于实验值,原因可能是由于裂隙压缩性系数和吸附应变系数存在估计误差。通过开展实验室渗透率实验和模型分析,对指导实验室内二氧化碳封存和气体驱替实验及其模拟研究具有借鉴意义。  相似文献   

5.
It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines.The spatio-temporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (CO2) pore pressure were increased to keep a constant positive effective stress on the sample. The changes internal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macroporosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlithotypes and microstructures.The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the lithotypes present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the internal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression.  相似文献   

6.
Laboratory observations have shown that coal permeability under the influence of gas adsorption can change instantaneously from reduction to enhancement. It is commonly believed that this instantaneous switching of permeability is due to the fact that the matrix swelling ultimately ceases at higher pressures and the influence of effective stresses take over. In this study, our previously-developed poroelastic model is used to uncover the true reason why coal permeability switches from reduction to enhancement. This goal is achieved through explicit simulations of the dynamic interactions between coal matrix swelling/shrinking and fracture aperture alteration, and translations of these interactions to perrmeability evolution under unconstrained swellings. Our results of this study have revealed the transition of coal matrix swelling from local swelling to macro-swelling as a novel mechanism for this switching. Our specific findings include: (1) at the initial stage of CO2 injection, matrix swelling is localized within the vicinity of the fracture compartment. As the injection continues, the swelling zone is extending further into the matrix and becomes macro-swelling. Matrix properties control the swelling transition from local swelling to macro swelling; (2) matrix swelling processes control the evolution of coal permeability. When the swelling is localized, coal permeability is controlled by the internal fracture boundary condition and behaves volumetrically; when the swelling becomes macro-swelling, coal permeability is controlled by the external boundary condition and behaves non-volumetrically; and (3) matrix properties control the switch from local swelling to macro swelling and the associated switch in permeability behavior from reduction to recovery. Based on these findings, a permeability switching model has been proposed to represent the evolution of coal permeability under variable stress conditions. This model is verified against our experimental data. It is found that the model predictions are consistent with typical laboratory and in-situ observations available in lietratures.  相似文献   

7.
针对煤层注水防尘过程中注水压力设置不合理、注水渗流效果差等问题,采用CT扫描技术与RFPA软件相结合的方法,构建了可以表征注水煤岩体内部孔裂隙结构的三维细观非均匀渗流损伤数值模型。通过对经过CT三维重构的煤岩模型进行不同注水压力的渗流损伤模拟,研究了煤层注水压力对煤样的渗流破坏、渗透率演化及声发射特性变化的影响;并通过对重构的煤岩模型进行缩放处理,研究了煤岩尺寸对煤样的渗流破坏和声发射变化的影响。研究结果表明：在煤样微观裂隙扩展过程中,随着注水压力的递增,煤样损伤单元数、渗流运动的渗流场分布范围、渗透率、声发射数目和能量总体呈上升趋势,局部范围内有波动发生,发生波动的原因是由于渗流运动的渗流场与煤样裂隙内部应力场发生临界反应,致使煤样破坏单元位置发生改变;煤样渗透率由3.82×10−5 μm2上升至0.314 μm2,孔隙率由5.45%上升至48.45%,揭示了煤岩体裂隙总体上随注水压力增大而不断扩展贯通,局部上随注水压力增大而扩展趋势有所下降的影响规律;随着煤样尺寸的增加,注水破坏后煤样的孔隙率呈现先下降后逐渐平稳的趋势,声发射特性变化趋势正好与之相反,表明煤样的尺寸对注水煤岩渗流破坏有显著影响,但当煤样尺寸超过40 mm时,煤样尺寸对注水煤岩渗流破坏的影响趋于稳定。CT扫描技术与RFPA软件相结合的方法能够有效模拟注水煤岩的裂隙渗流扩展行为。  相似文献   

8.
Permeability is one of the most significant reservoir parameters. It is commonly obtained by experiment, history simulation, injection/falloff well test and geophysical logging. Among these, geophysical logging remains as the most economic and efficient technique in evaluating coal permeability in the vicinity of an open-hole. In this paper, geophysical logging data are used to evaluate the coal reservoir permeability for the No. 3 coal seam in the southern Qinshui Basin (Fanzhuang and Zhengzhuang coal zones). Ideally coal reservoirs consist of coal matrix and fracture networks that can be represented by a model called a collection of sheets. Based on the model, coal reservoir permeability can be quantitatively calculated using the theoretical formula of kf = 8.50 × 10− 4 w2φf, in which fracture width (w) and fracture porosity (φf) were obtained by dual laterolog and density logging data, respectively. Calculative results show that coal reservoir permeability ranged from 0.017 mD to 0.617 mD for the Fanzhuang coal zone and from 0.047 mD to 1.337 mD for the Zhengzhuang coal zone. The permeability decreases with coal burial depth, reflecting variations in penetration capability of coal reservoirs at varying depths. Comparing results with those from injection/falloff well tests, however, shows that the model-calculated permeability is slightly higher. This is expected because the model did not include the influence from coal anisotropy.  相似文献   

9.
There is still no clear understanding of the specific interactions between coal and gas molecules. In this context sorption–desorption studies of methane and carbon dioxide, both in a single gas environment and gas mixtures, are of fundamental interest. This paper presents the results of unique simultaneous measurements of sorption kinetics, volumetric strain and acoustic emission (AE) on three tetragonal coal samples subjected to sorption of carbon dioxide and methane mixtures. The coal was a high volatile bituminous C coal taken from the Budryk mine in the Upper Silesia Basin, Poland. Three different gas mixtures were used in the sorption tests, with dominant CO2, with dominant CH4 and a 50/50 mixture.The experimental set-up was designed specially for this study. It consisted of three individual units working together: (i) a unit for gas sorption experiments using a volumetric method, (ii) an AE apparatus for detecting, recording and analysing AE, and (iii) a strain meter for measuring strains induced in the coal sample by gas sorption/desorption. All measurements were computer aided.The experiments indicated that the coal tested showed preferential sorption of CH4 at 2.6 MPa pressure and exhibited comparable affinities for CH4 and CO2 at higher pressures (4.0 MPa). The results of chromatographic analysis of the gas released on desorption suggested that the desorption of methane from the coal was favoured. The relationship between the volumetric strain and the amount of sorbed gas was found to be non-linear. These results were contrary to common opinions on the coal behaviour. Furthermore, it appeared that the swelling/shrinkage of coal was clearly influenced by the network of fractures. Besides, the AE and strain characteristics suggested common sources of sorption induced AE and strain.The present results may have implications for the sequestration of carbon dioxide in coal seams and enhanced coalbed methane recovery (ECBM).  相似文献   

10.
Sorption and desorption behaviour of methane, carbon dioxide, and mixtures of the two gases has been studied on a set of well-characterised coals from the Argonne Premium Coal Programme. The coal samples cover a maturity range from 0.25% to 1.68% vitrinite reflectance. The maceral compositions were dominated by vitrinite (85% to 91%). Inertinite contents ranged from 8% to 11% and liptinite contents around 1% with one exception (Illinois coal, 5%). All sorption experiments were performed on powdered (−100 mesh), dry coal samples.Single component sorption/desorption measurements were carried out at 22 °C up to final pressures around 51 bar (5.1 MPa) for CO2 (subcritical state) and 110 bar (11 MPa) for methane.The ratios of the final sorption capacities for pure CO2 and methane (in molar units) on the five coal samples vary between 1.15 and 3.16. The lowest ratio (1.15) was found for the North Dakota Beulah-Zap lignite (VRr=0.25%) and the highest ratios (2.7 and 3.16) were encountered for the low-rank coals (VRr 0.32% and 0.48%) while the ratio decreases to 1.6–1.7 for the highest rank coals in this series.Desorption isotherms for CH4 and CO2 were measured immediately after the corresponding sorption isotherms. They generally lie above the sorption isotherms. The degree of hysteresis, i.e. deviation of sorption and desorption isotherms, varies and shows no dependence on coal rank.Adsorption tests with CH4/CO2 mixtures were conducted to study the degree of preferential sorption of these two gases on coals of different rank. These experiments were performed on dry coals at 45 °C and pressures up to 180 bar (18 MPa). For the highest rank samples of this sequence preferential sorption behaviour was “as expected”, i.e. preferential adsorption of CO2 and preferential desorption of CH4 were observed. For the low rank samples, however, preferential adsorption of CH4 was found in the low pressure range and preferential desorption of CO2 over the entire pressure range.Follow-up tests for single gas CO2 sorption measurements consistently showed a significant increase in sorption capacity for re-runs on the same sample. This phenomenon could be due to extraction of volatile coal components by CO2 in the first experiment. Reproducibility tests with methane and CO2 using fresh sample material in each experiment did not show this effect.  相似文献   

11.
For the degassing of coal seams, either prior to mining or in un-minable seams to obtain coalbed methane, it is the combination of cleat frequency, aperture, connectivity, stress, and mineral occlusions that control permeability. Unfortunately, many potential coalbeds have limited permeability and are thus marginal for economic methane extraction. Enhanced coalbed methane production, with concurrent CO2 sequestration is also challenging due to limited CO2 injectivity. Microwave energy can, in the absence of confining stress, induce fractures in coal. Here, creation of new fractures and increasing existing cleat apertures via short burst, high-energy microwave energy was evaluated for an isotropically stressed and an unstressed bituminous coal core. A microwave-transparent argon gas pressurized (1000 psi) polycarbonate vessel was constructed to apply isotropic stress simulating ~ 1800 foot depth. Cleat frequency and distribution was determined for the two cores via micro-focused X-ray computed tomography. Evaluation occurred before and after microwave exposure with and without the application of isotropic stress during exposure. Optical microscopy was performed for tomography cleat aperture calibration and also to examine lithotypes influences on fracture: initiation, propagation, frequency, and orientation. It was confirmed that new fractures are induced via high-energy microwave exposure in an unconfined bituminous core and that the aperture increased in existing cleats. Cleat/fracture volume, following microwave exposure increased from 1.8% to 16.1% of the unconfined core volume. For the first time, similar observations of fracture generation and aperture enhancement in coal were also determined for microwave exposure under isotropic stress conditions. An existing cleat aperture, determined from calibrated X-ray computed tomography increased from 0.17 mm to 0.32 mm. The cleat/fracture volume increased from 0.5% to 5.5%. Optical microscopy indicated that fracture initiated likely occurred in at least some cases at fusain microlithotypes. Presumably this was due to the open pore volumes and potential for bulk water presence or steam pressure buildup in these locations. For the major induced fractures, they were mostly horizontal (parallel to the bedding plane) and often contained within lithotype bands. Thus it appears likely that microwaves have the potential to enhance the communication between horizontal wellbore and existing cleat network, in coal seams at depth, for improved gas recovery or CO2 injection.  相似文献   

12.
渗透率是表征瓦斯流动的重要参数,为保证煤矿瓦斯安全高效抽采,有必要探究距抽采井筒不同位置处煤层瓦斯渗流演化特征。然而,瓦斯抽采过程中伴随有效应力、煤基质对瓦斯的吸附/解吸能力以及煤储层温度的不断变化,甚至出现抽采损伤,使得煤层瓦斯运移行为异常复杂。为探究抽采过程的煤层瓦斯渗流特性,在圆柱坐标系下,考虑压力场与温度场变化对煤储层渗透率的影响,构建温度影响的孔隙压力时空演化函数,据此建立应力与温度作用下的煤储层渗透率模型。结果表明:建立的模型能合理描述沿抽采井筒孔隙压力的演化规律以及瓦斯的运移特性,即在恒定外应力的条件下,随抽采时间增加,不同位置处孔隙压力先降低后变化平缓,煤储层渗透率先降低后升高;此外,同一煤储层位置处,考虑温度比不考虑温度的渗透率计算值更低;通过讨论发现,随抽采时间增加,根据裂隙压缩与基质收缩对渗透率演化的不同效应,设置合理的负压抽采方式可提高瓦斯抽采量。   相似文献   

13.
It has been widely reported that coal permeability can change from reduction to enhancement due to gas adsorption even under the constant effective stress condition, which is apparently inconsistent with the classic theoretical solutions. This study addresses this inconsistency through explicit simulations of the dynamic interactions between coal matrix swelling/shrinking induced damage and fracture aperture alteration, and translations of these interactions to permeability evolution under the constant effective stress condition. We develop a coupled coal–gas interaction model that incorporates the material heterogeneity and damage evolution of coal, which allows us to couple the progressive development of damage zone with gas adsorption processes within the coal matrix. For the case of constant effective stress, coal permeability changes from reduction to enhancement while the damage zone within the coal matrix develops from the fracture wall to further inside the matrix. As the peak Langmuir strain is approached, the decrease of permeability halts and permeability increases with pressure. The transition of permeability reduction to permeability enhancement during gas adsorption, which may be closely related to the damage zone development in coal matrix, is controlled by coal heterogeneity, external boundary condition, and adsorption-induced swelling.  相似文献   

14.
为了探究有效应力对高煤级煤储层渗透率的控制作用及其应力敏感性的各向异性,对5块高煤级煤样进行了覆压孔渗实验,揭示了有效应力对煤储层渗透率的控制机理。以3.5 MPa模拟原始地层压力发现,煤岩在平行主裂隙和层理面方向具有最高的初始渗透率,垂直层理面方向初始渗透率最低;有效应力从3.5 MPa增加到15.5 MPa的过程中,渗透率呈现出良好的幂函数降低趋势;渗透率伤害/损失的各向异性表明平行主裂隙方向渗透率伤害率和损失率最大,且不同方向应力敏感性受裂隙的宽度及其展布方向的控制;裂隙压缩系数随应力的增加呈现降低趋势,但由于高煤级煤岩压缩难度大,裂隙压缩系数的各向异性不明显。有效应力对渗透率控制的实质为通过减小煤储层孔裂隙体积降低渗透率,从而对各个方向上的渗透率均造成较大的不可逆伤害。   相似文献   

15.
为了研究深部煤体在开采扰动影响下的渗透率演化规律,以三向应力条件下的煤体渗透率模型为基础,从吸附解吸作用引起裂隙变形和损伤破裂造成煤基质弹性模量劣化的角度进行理论推导,引入内膨胀应变系数的概念,同时基于Drucker-Prager破坏准则的损伤本构关系建立了两种考虑煤体损伤破裂的渗透率演化模型——指数型和立方型,并且对常规三轴加载、开采扰动加卸载和改变气体压力下的瓦斯渗透试验结果进行了拟合分析。结果表明：所构建的两种模型可以较好地反映常规三轴加载和开采扰动加卸载下煤体渗透率的分区段变化特征,也可以描述有效围压恒定条件下煤体渗透率随气体压力升高而降低的规律。在开采扰动加卸载和改变气体压力的试验中,指数型的拟合效果略优于立方型。研究结果可为深部煤炭开采及瓦斯抽采的工作提供指导。  相似文献   

16.
This paper presents reviews of studies on properties of coal pertinent to carbon dioxide (CO2) sequestration in coal with specific reference to Victorian brown coals. The coal basins in Victoria, Australia have been identified as one of the largest brown coal resources in the world and so far few studies have been conducted on CO2 sequestration in this particular type of coals. The feasibility of CO2 sequestration depends on three main factors: (1) coal mass properties (chemical, physical and microscopic properties), (2) seam permeability, and (3) gas sorption properties of the coal. Firstly, the coal mass properties of Victorian brown coal are presented, and then the general variations of the coal mass properties with rank, for all types of coal, are discussed. Subsequently, coal gas permeability and gas sorption are considered, and the physical factors which affect them are examined. In addition, existing models for coal gas permeability and gas sorption in coal are reviewed and the possibilities of further development of these models are discussed. According to the previous studies, coal mass properties and permeability and gas sorption characteristics of coals are different for different ranks: lignite to medium volatile bituminous coals and medium volatile bituminous to anthracite coals. This is important for the development of mathematical models for gas permeability and sorption behavior. Furthermore, the models have to take into account volume effect which can be significant under high pressure and temperature conditions. Also, the viscosity and density of supercritical CO2 close to the critical point can undergo large and rapid changes. To date, few studies have been conducted on CO2 sequestration in Victorian brown coal, and for all types of coal, very few studies have been conducted on CO2 sequestration under high pressure and temperature conditions.  相似文献   

17.
以沁水盆地成庄矿煤样为研究对象,利用实验室自主研发的CO2注入与煤层气强化开采实验模拟装置进行不同有效应力和CO2吸附压力下的煤岩渗透率测试。实验结果表明,煤岩的裂隙压缩系数受到CO2吸附的影响,初始状态下、亚临界CO2吸附和超临界CO2吸附煤样裂隙压缩系数分别为0.066、0.086和0.089。引起裂隙压缩系数改变的原因主要有两方面:CO2和煤中矿物反应提高了煤基质的不连续性;CO2软化了煤基质同时降低了煤岩的力学性质。利用考虑吸附应变以及内部膨胀系数的渗透率模型对实测渗透率进行拟合,发现有效应力和内部膨胀系数成正比。CO2吸附压力和有效应力的增大均提高了煤岩的内部膨胀系数,这影响了煤岩孔裂隙的开度,降低了煤储层的渗透率,并最终降低CO2在煤储层中的可注性。   相似文献   

18.
Field experiments and laboratory studies have shown that swelling of coal takes place upon contact with carbon dioxide at underground pressure and temperature conditions. Understanding this swelling behavior is crucial for predicting the performance of future carbon dioxide sequestration operations in unminable coal seams conducted in association with methane production. Swelling is believed to be related to adsorption on the internal coal surface. Whereas it is well established that moisture influences the sorption capacity of coal, the influence of water on coal swelling is less well-defined. This paper presents the results of laboratory experiments to investigate the effect of moisture on coal swelling in the presence of carbon dioxide, methane and argon. Strain development of an unconfined sample of about 1.0–1.5 mm3 at 40 °C and 8 MPa (and at other pressures) was observed in an optical cell under a microscope as a function of time. Both air dried and moisturized samples were used. Results confirmed different swelling behaviors of coal with different substances: carbon dioxide leads to higher strain than methane, while exposure to argon leads to very little swelling. The experiments on moisturized samples seem to confirm the role of moisture as a competitor to gas molecules for adsorption sites. Adsorption of water could also explain the observed swelling due to water uptake at atmospheric pressure. A re-introduction of carbon dioxide, after intermediate gas release, results in higher strains which indicate a drying effect of the carbon dioxide on the coal. The results of this study show that the role of water cannot be ignored if one wants to understand the fundamental processes that are taking place in enhanced coalbed methane operations.  相似文献   

19.
The sensitivity of coal permeability to the effective stress means that changes in stress as well as pore pressure within a coal seam lead to changes in permeability. In addition coal swells with gas adsorption and shrinks with desorption; these sorption strains impact on the coal stress state and thus the permeability. Therefore the consideration of gas migration in coal requires an appreciation of the coupled geomechanical behaviour. A number of approaches to representing coal permeability incorporate the geomechanical response and have found widespread use in reservoir simulation. However these approaches are based on two simplifying assumptions; uniaxial strain (i.e. zero strain in the horizontal plane) and constant vertical stress. This paper investigates the accuracy of these assumptions for reservoir simulation of enhanced coalbed methane through CO2 sequestration. A coupled simulation approach is used where the coalbed methane simulator SIMED II is coupled with the geomechanical model FLAC3D. This model is applied to three simulation case studies assembled from information presented in the literature. Two of these are for 100% CO2 injection, while the final example is where a flue gas (12.5% CO2 and 87.5% N2) is injected. It was found that the horizontal contrast in sorption strain within the coal seam caused by spatial differences in the total gas content leads to vertical stress variation. Thus the permeability calculated from the coupled simulation and that using an existing coal permeability model, the Shi–Durucan model, are significantly different; for the region in the vicinity of the production well the coupled permeability is greater than the Shi–Durucan model. In the vicinity of the injection well the permeability is less than that calculated using the Shi–Durucan model. This response is a function of the magnitude of the strain contrast within the seam and dissipates as these contrasts diminish.  相似文献   

20.
为了研究煤体渗透率与压力梯度之间的关系,在考虑煤体吸附变形的基础上建立了煤体渗透率与瓦斯压力梯度的数学模型,并在恒温条件下进行同一压力梯度不同吸附平衡压力的条件下和同一吸附平衡压力不同压力梯度条件下的渗流实验。研究结果表明:在较低的孔隙压力条件下,煤体渗透率随着吸附平衡压力和压力梯度的增加而减小;建立的渗透率动态演化模型能够较好地描述煤层瓦斯抽采过程中瓦斯的流动规律。研究结果可以为我国煤矿瓦斯治理和抽采工作提供一定的理论支撑,具有一定的指导和实践意义。   相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号