共查询到20条相似文献，搜索用时 31 毫秒
1.
The experimental results have so far shown that when a wave breaks on a vertical wall with an almost vertical front face at the instant of impact that is called perfect breaking or perfect impact, the greatest impact forces are produced on the wall. Therefore, the configuration of breaking waves is important in the design considerations of coastal structures. The present study is concerned with determining the geometrical properties of oscillatory waves that break perfectly on the vertical wall of composite-type breakwaters. The laboratory tests for perfect breaking waves on composite breakwaters are conducted with base slopes of 1/2, 1/4 and 1/6, and with berm widths of 0.00, 0.10, 0.20, 0.30 and 0.40 m. The shape and the dimensions of waves at the instant of perfect breaking on the wall are determined using a video camera. The experimental results for the geometrical properties of the breakers are presented non-dimensionally. Within the range of present experimental conditions, it is found that the dimensionless breaker crest height, hb/dw, and dimensionless breaker height, Hb/dw, decrease; and, dimensionless breaker depth, dw/H0, increases with increasing relative berm width, B/D. The breaker height index, Hb/H0, is almost unaffected by B/D. The deep-water wave steepness and the base slope of the breakwater do not seem to influence the geometrical properties of the breakers at wall systematically. 相似文献
2.
Breaking wave loads on coastal structures depend primarily on the type of wave breaking at the instant of impact. When a wave breaks on a vertical wall with an almost vertical front face called the “perfect breaking”, the greatest impact forces are produced. The correct prediction of impact forces from perfect breaking of waves on seawalls and breakwaters is closely dependent on the accurate determination of their configurations at breaking. The present study is concerned with the determination of the geometrical properties of perfect breaking waves on composite-type breakwaters by employing artificial neural networks. Using a set of laboratory data, the breaker crest height, hb, breaker height, Hb, and water depth in front of the wall, dw, from perfect breaking of waves on composite breakwaters are predicted using the artificial neural network technique and the results are compared with those obtained from linear and multi-linear regression models. The comparisons of the predicted results from the present models with measured data show that the hb, Hb and dw values, which represent the geometry of waves breaking directly on composite breakwaters, can be predicted more accurately by artificial neural networks compared to linear and multi-linear regressions. 相似文献
3.
The wave forces and moments on and the water surface fluctuations around a vertical circular cylinder encircled by a perforated square caisson were experimentally investigated. The porosity of the outer square caisson was varied from 4.24 to 14.58%. The in-line wave forces on the inner vertical cylinder are influenced by changing the porosity of the outer caisson, whereas the variations in the water surface fluctuations are less influenced in this porosity range. The in-line moment on the vertical cylinder is relatively less sensitive when the porosity is increased from 4.24 to 8.75%, but varies substantially when it is increased from 8.75 to 14.58%. The force and moment ratio (i.e. the ratio of the force or moment on the vertical cylinder, when it is encircled by the perforated caisson to the force or moment on the cylinder without any protection around it) reduces with increased wave height, H, and wave length, L, whereas the wave height ratio (ratio of the wave height at a point in the vicinity of the structure to the incident wave height) is less sensitive for the varying H and L. A new non-dimensional parameter, p1.5 (D/L)/(H/d), is introduced to predict the in-line force and moment on the inner vertical cylinder, where d is local water depth, D is the diameter of the inner cylinder and p is the porosity of the outer caisson in percentage. Simple predictive equations for forces, moments and water surface fluctuations are provided. 相似文献
4.
《Coastal Engineering》1998,35(3):185-209
Two depth inversion algorithms (DIA) applicable to coastal waters are developed, calibrated, and validated based on results of computations of periodic waves shoaling over mild slopes, in a two-dimensional numerical wave tank based on fully nonlinear potential flow (FNPF) theory. In actual field situations, these algorithms would be used to predict the cross-shore depth variation h based on sets of values of wave celerity c and length L, and either wave height H or left–right asymmetry s2/s1, simultaneously measured at a number of locations in the direction of wave propagation, e.g., using video or radar remote sensing techniques. In these DIAs, an empirical relationship, calibrated for a series of computations in the numerical wave tank, is used to express c as a function of relative depth koh and deep water steepness koHo. To carry out depth inversion, wave period is first predicted as the mean of observed L/c values, and Ho is then predicted, either based on observed H or s2/s1 values. The celerity relationship is finally inverted to predict depth h. The algorithms are validated by applying them to results of computations for cases with more complex bottom topography and different incident waves than in the original calibration computations. In all cases, root-mean-square (rms)-errors for the depth predictions are found to be less than a few percent, whereas depth predictions based on the linear dispersion relationship—which is still the basis for many state-of-the-art DIAs—have rms-errors 5 to 10 times larger. 相似文献
5.
Prediction of scour depth at breakwaters due to non-breaking waves using machine learning approaches
Coastal structures may cease to function properly due to seabed scouring. Hence, prediction of the maximum scour depth is of great importance for the protection of these structures. Since scour is the result of a complicated interaction between structure, sediment, and incoming waves, empirical equations are not as accurate as machine learning schemes, which are being widely employed for the coastal engineering modeling. In this paper, which can be regarded as an extension of Pourzangbar et al. (2016), two soft computing methods, a support vector regression (SVR), and a model tree algorithm (M5′), have been implemented to predict the maximum scour depth due to non-breaking waves. The models predict the relative scour depth (Smax/H0) on the basis of the following variables: relative water depth at the toe of the breakwater (htoe/L0), Shields parameter (θ), non-breaking wave steepness (H0/L0), and reflection coefficient (Cr). 95 laboratory data points, extracted from dedicated experimental studies, have been used for developing the models, whose performances have been assessed on the basis of statistical parameters. The results suggest that all of the developed models predict the maximum scour depth with high precision, the M5′ model performed marginally better than the SVR model and also allowed to define a set of transparent and physically sound relationships. Such relationships, which are in good agreement with the existing empirical findings, show that the relative scour depth is mainly affected by wave reflection. 相似文献
6.
The hydrodynamic efficiency of the vertical porous structures is investigated under regular waves by use of physical models. The hydrodynamic efficiency of the breakwater is presented in terms of the wave transmission (kt ), reflection (kr) and energy dissipation (kd ) coefficients. Different wave and structural parameters affecting the breakwater efficiency are tested. It is found that, the transmission coefficient (kt ) decreases with the increase of the relative water depth (h/L), the wave steepness (Hi/L), the relative breakwater widths (B/L, B/h), the relative breakwater height (D/h), and the breakwater porosity (n). The reflection coefficient (kr) takes the opposite trend of kt when D/h=1.25 and it decreases with the increasing h/L, Hi/L and B/L when D/h 1.0. The dissipation coefficient (kd) increases with the increasing h/L, Hi/L and B/L when D/h 1.0 and it decreases when D/h=1.25. In which, it is possible to achieve values of kt smaller than 0.3, krlarger than 0.5, and kd larger than 0.6 when D/h=1.25, B/h=0.6, h/L 0.22, B/L 0.13, and Hi/L 0.04. Empirical equations are developed for the estimation of the transmission and reflection coefficients. The results of these equations are compared with other experimental and theoretical results and a reasonable agreement is obtained. 相似文献
7.
Submerged breakwaters (SBWs) are becoming a popular option for coastal protection, mainly due to their low aesthetic impact on the natural environment. However, SBWs have rarely been employed for coastal protection in the past and therefore, their efficacy remains largely unknown. The main objective of the present study was to investigate the structural and environmental conditions that govern the mode of shoreline response (i.e shoreline erosion vs shoreline accretion) to SBWs. The relative importance of the key structural and environmental parameters governing the response mode to a single shore parallel SBW is investigated through a combination of theoretical analysis and numerical modelling. Using physical considerations, a theoretical response-function model is derived under several simplifying assumptions including parallel depth contours, linear wave theory, shore normal waves, and no wave–current interaction. Numerical modelling is undertaken with the Mike21 model suite to simulate the depth averaged velocity fields (without morphological updating) due to waves acting on a single shore-parallel SBW located on a schematised beach with parallel depth contours. In total 92 coupled wave–current simulations were undertaken. The results indicate that the mode of shoreline response to the SBW can be expressed in terms of the two non-dimensional parameters hB/H0 and (sB/hB)3/2(LB/hB)2(A3/hB)1/2 (variables defined in the text). 相似文献
8.
A beach profile equilibrium model for perched beaches is presented. The model assumes that wave reflection at the seaward and leeward sides of the breakwater is the most important process that modifies Dean's equilibrium profile model for non-perched beaches. The influence of wave breaking over the submerged structure is also discussed. Several laboratory data sets are used to analyze the merit of the proposed model for describing the equilibrium condition of a perched beach. A good comparison is obtained. Results show that if the ratio between the water depth above the submerged structure, d, and the water depth at the toe of the structure, he, is large, d/he>0.5, only minor advance of the shoreline is achieved with the construction of a toe structure. A considerable advance is obtained for d/he less that 0.1. In these situations, however, resonant effects may result in an inefficient structure. The proposed model is used to provide an estimation for the required sand volume and the associated beach advance for the case of narrow breakwaters. 相似文献
9.
The wave transmission, reflection and energy dissipation characteristics of ‘’-type breakwaters were studied using physical models. Regular and random waves in a wide range of wave heights and periods and a constant water depth were used. Five different depths of immersion (two emerged, one surface flushing and two submerged conditions) of this breakwater were selected. The coefficient of transmission, Kt, and coefficient of reflection, Kr, were obtained from the measurements, and the coefficient of energy loss, Kl was calculated using the law of balance of energy. It was found that the wave transmission is significantly reduced with increased relative water depth, d/L, whether the vertical barrier of the breakwater is surface piercing or submerged, where ‘d’ is the water depth and ‘L’ is the wave length. The wave reflection decreases and energy loss increases with increased wave steepness, especially when the top tip of the vertical barrier of this breakwater is kept at still water level (SWL). For any incident wave climate (moderate or storm waves), the wave transmission consistently decreases and the reflection increases with increased relative depth of immersion, Δ/d from −0.142 to 0.142. Kt values less than 0.3 can be easily obtained for the case of Δ/d=+0.071 and 0.142, where Δ is the height of exposure (+ve) or depth of immersion (−ve) of the top tip of the vertical barrier. This breakwater is capable of dissipating wave energy to an extent of 50–80%. The overall performance of this breakwater was found to be better in the random wave fields than in the regular waves. A comparison of the hydrodynamic performance of ‘’-type and ‘T’-type shows that ‘T’-type breakwater is better than ‘’-type by about 20–30% under identical conditions. 相似文献
10.
O.S. Rageh 《Ocean Engineering》2009,36(14):1112-1118
The efficiency of the breakwater, which consists of caissons supported on two or three rows of piles, was studied using physical models. The efficiency of the breakwater is presented as a function of the transmission, reflection and the wave energy dissipation coefficients. Regular waves with wide ranges of wave heights and periods and constant water depth were used. Different characteristics of the caisson structure and the supporting pile system were also tested. It was found that, the transmission coefficient (kt) decreases with increasing the relative breakwater draft D/L, increasing the relative breakwater width B/h, and decreasing the piles gap-diameter ratio G/d. It is possible to achieve kt values less than 0.25 when D/L≥0.1. The reflection coefficient takes the opposite trend especially when D/L≤0.15. The proposed breakwater dissipates about 10-25% of the incident wave energy. Also, simple empirical equations are developed for estimating the wave transmission and reflection. In addition, the proposed breakwater model is efficient compared with other floating breakwaters. 相似文献
11.
The wave transmission characteristics and wave induced pressures on twin plate breakwater are investigated experimentally in regular and random waves.A total of twenty pressure transducers are fixed on four surfaces of twin plate to measure the wave induced dynamic pressures.The spatial distribution of dynamic wave pressure is given along the surface of the twin plate.The uplift wave force obtained by integrating the hydrodynamic pressure along the structure is presented.Discussed are the influence of different incident wave parameters including the relative plate width B /L,relative wave height /i H a and relative submergence depth s /a on the non-dimensional dynamic wave pressures and total wave forces.From the investigation,it is found that the optimum transmission coefficient,t K occurs around B /L 0.41 ~ 0.43,and the twin plate breakwater is more effective in different water depths.The maximum of pressure ratio decreases from 1.8 to 1.1 when the relative submergence depth of top plate is increased from 0.8to +0.8. 相似文献
12.
The stability of a uniformly sloped conventional rubble mound breakwater defenced by a seaward submerged reef is investigated using physical model studies. Regular waves of wide ranging heights and periods are used. Tests are carried out for different spacings between two rubble mound structures (X/d=2.5–13.33) and for different relative heights (h/d=0.625–0.833) and relative widths (B/d=0.25–1.33) of the reef. It is observed that a reef of width (B/d) of 0.6–0.75 constructed at a seaward distance (X/d) of 6.25–8.33 breaks all the incoming waves and dissipates energy and protects the breakwater optimally. 相似文献
13.
Mooring forces in horizontal interlaced moored floating pipe breakwater with three layers 总被引：2，自引：0，他引：2
The paper presents the results from model scale experiments on the study of forces in the moorings of horizontally interlaced, multi-layered, moored floating pipe breakwaters. The studies are conducted with breakwater models having three layers subjected to waves of steepness Hi/L (Hi is the incident wave height and L the wavelength) varying from 0.0066 to 0.0464, relative width W/L (W is the width of breakwater) varying from 0.4 to 2.65, and relative spacing S/D (S is the spacing of pipes and D the diameter of pipe) of 2 and 4. The variation of measured normalized mooring forces on the seaward side and leeward side are analyzed by plotting non-dimensional graphs depicting f/γW2 (f is the force in the mooring per unit length of the breakwater, γ the weight density of sea water) as a function W/L for various values of Hi/d (d is the depth of water). It is found that the force in the seaward side mooring increases with an increase in Hi/L for d/W values ranging between 0.081 and 0.276. The experimental results also reveal that the forces in the seaward side mooring decrease as W/L increases, up to a value of W/L=1.3, and then increases with an increase in W/L. It is also observed that the wave attenuation characteristics of breakwater model with relative spacing of 4 is better than that of the model with relative spacing of 2. The maximum force in the seaward side mooring for model with S/D=4 is lower compared to that for the breakwater model with S/D=2. A multivariate non-linear regression analysis has been carried out for the data on mooring forces for the seaside and leeside. 相似文献
14.
跨海大桥桥墩基础施工若采用双壁钢围堰,则在其外壁进行开孔可有效减小波浪力,有利于降低钢围堰的制作造价和提高基础施工的安全性。以某跨海大桥基础施工采用的双壁圆形钢吊箱围堰为研究对象,引入波浪力折减系数Kd对消波效果进行评价,采用数值方法着重分析波浪参数和围堰自身结构设计参数对消波效果的影响规律。结果表明:Kd随波陡增大呈先快后缓的增大趋势,波陡超过0.032后,消波效果基本不再变化;随着相对水深的增大,Kd呈先减小后增大并趋缓的规律,在相对水深d/L约为0.455时取得最小值;Kd随开孔率的增大呈线性减小,开孔率越大,消波效果越好。随着双壁间距s的增大,Kd总体上呈减小趋势,且减小速率先快后慢;双壁间距较小时,开孔的消波作用较弱。开孔率和双壁间距两种因素间存在耦合作用,两者越大,其耦合作用也越强。围堰设计中可适当增大开孔率并选取合适的双壁间距以得到最佳消波效果。 相似文献
15.
A parametric study was carried out to investigate the hydrodynamics of a cylindrical wave energy absorber. Established methods of hydrodynamic analysis were applied to the case of a damped vertically oriented cylinder pivoted near the sea floor in intermediate depth water. The simple geometry provides a canonical reference for more complex structure shapes and configurations that may be considered for either wave energy conversion or wave energy absorption. The study makes use of the relative velocity Morison equation, with force coefficients derived from radiation and diffraction theory. Viscous effects were accounted for by including a drag term with an empirically derived coefficient, CD. A non-linear first-order formulation was used to calculate the cylinder motion response in regular waves. It was found that the non-linear drag term, which is often neglected in studies on wave energy conversion, has a large effect on performance. Results from the study suggest a set of design criteria based on Keulegan–Carpenter (KC) number, ratio of cylinder radius to water depth (a/h), and ratio of water depth to wavelength (h/L). Respectively, these parameters account for viscous, wave radiation, and water depth effects, and optimal ranges are provided. 相似文献
16.
The hydrodynamic performance of vertical and sloped plane, dentated and serrated seawalls were investigated using physical model studies. Regular and random waves of wide range of heights and periods were used. Tests were carried out for different inclinations of the seawall (i.e. θ=30, 40, 50, 60 and 90°) and for a constant water depth of 0.7 m. The wave reflection was measured to assess the dissipation character of the seawalls. It was observed that the serrated seawall was superior to the plane and dentated seawall in reducing the wave reflection. Even for the vertical case, the coefficient of reflection due to regular waves for dentated seawall ranged from 0.6–0.99 and for the vertical serrated seawall it was 0.45–0.98, whereas for the vertical plane wall, it was almost 1.0. It was found that the characteristic dimension of the seawall (i.e. L/W) and the relative water depth (i.e. d/L) were better influencing parameters compared to the conventionally used surf similarity parameter ‘ξ’ (ξ=tan θ/(Hi/L)0.5) in predicting the reflection from the dentated and serrated seawall, where L is the local wave length, W the width of the dent along the length of the seawall slope, d the water depth at the toe and Hi is the incident wave height. A similar trend was observed for the random waves too. The reduction in the wave reflection due to random waves for the dentated seawall as compared to the plane seawall was about 18% and for the serrated seawall, it was 20%. It was observed that the reflection due to random waves was lesser for all the three different walls than the regular waves, due to the mutual interaction of random waves. Multiple regression analysis on the measured data points was carried out and predictive equations for the reflection coefficient were obtained for both regular and random waves. This study will be useful in the design of energy dissipating type vertical quay walls in ports and harbours, sloped seawalls for shore protection from erosion and sloped caisson as breakwaters. Comparison of predictive formulae with the experimental results revealed that the prediction methods were good enough for practical purposes. 相似文献
17.
The prediction of ship stability during the early stages of the design process is very important from the point of a vessel's safety. Hence, in this study, a formula is presented to estimate cross curves of fishing vessels to predict initial stability at the preliminary design stage. For this purpose, 175 fishing vessel forms have been generated from Doust trawler hull series. The predictive technique is established by regression analysis of systematically varied fishing vessel series data. The mathematical model is constructed as a function of main design parameters such as length to beam ratio LWL/BWL, beam to draft ratio BWL/T, moulded depth to draft ratio D/T and block coefficient CB. This prediction is also used to determine the effect of specific hull form parameters and load conditions on the stability of the fishing vessel. Some basic considerations on how the proposed method can be applied to a new fishing vessel are presented. 相似文献
18.
Li Luping 《海洋学报(英文版)》1997,16(1):45-56
In this paper, it is held that the universal relationships of wave growth in fetch-limited conditions , i. e.,(f|~) p=A(x|~)-Band (m|~)0= C(x|~) Dshould satisfy the Toba 3/2 power law and the wave energy balance equation. In the ideal generation situation, theoretically it can be derived that the ideal fetch-limited wave growth relationship should have D=3B and D B =1, (i.e., B = 0.25, D = 0.75 ) and A3C=2. 1×l(T4C~(1/2)_d , where Cd is the drag coefficient. The 3/2 power law, the wave energy balance equation and the decrease of wave steepness with increasing fetch have became three requirements which should be satisfied by fetch-limited wave growth algorithms. A semi-empirical and semi-theoretical model for fetch-limited wave growth is presented. In the application to the slanting wind situation an un(?)ersal relationship of dimensionless wave energy vs dimensionless peak frequency is presented and the comparisons show that the model is in good agreement with observations. 相似文献
19.
C.Ernest Knowles 《Estuarine, Coastal and Shelf Science》1983,17(4):395-404
According to small-amplitude theory, the surface gravity-wave spectrum can be estimated from a subsurface pressure-fluctuation spectrum by applying a factor (K) that compensates for the attenuation of surface-wave amplitude as the depth below the water surface and the wave frequency increase.There are a number of factors, however, that cause K to be inaccurate over a large portion of the spectrum's frequency range. Numerous attempts have been made to derive an empirical correction factor (n) that could be applied to K to provide a better estimate of the surface-wave spectrum. This paper evaluates some of these empirical factors, specifically for use in an estuarine environment, and recommends Graces' (1978) equation for n as a function of the non-dimensional frequency parameter kh (where is the local wavenumber, h the local depth and L the wavelength).The paper also evaluates the maximum limit (Kmax) on the magnitude of K suggested by Esteva & Harris (1970), where relative depth (d is the pressure transducer height above the bottom) and koh (a parameter directly related for large values of kh to wave frequency by the dispersion relation) are the independent variables. The choice of Kmax may be made unimportant if d is selected beforehand using an equation (Knowles, 1981a) for the minimum limit affected by the choice of Kmax. 相似文献
20.
Experiments were performed in a wave flume to measure the intensity, transmission and reflection of waves breaking over a submerged reef with an offshore gradient of 1:10. The results demonstrate that the relative water depth over the reef crest (hc/Ho) is a dominant factor affecting the breaking characteristics. In particular it is found that as the relative crest submergence is reduced, there is a considerable increase in the intensity of wave breaking over the reef that can be quantified through measurements of the air cavity enclosed beneath the plunging jet. It is also shown that there is a corresponding decrease in wave transmission and reflection as the submergence is reduced. 相似文献