共查询到20条相似文献，搜索用时 62 毫秒
1.
基于FVCOM 的渤海潮波数值模拟 总被引：1，自引：0，他引：1
基于有限体积法海洋数值模型(FVCOM),对渤海当前水深岸线状况下的潮汐潮流进行了数值计算。模式采用不规则三角形网格,较好地提高了黄河口处网格分辨率,模拟了渤海海域K1,O1,M2和S2四个主要分潮。利用渤海沿岸19个验潮站的资料对模拟结果进行了验证,K1分潮振幅绝均差2.39 cm,迟角绝均差4.36°,O1分潮振幅绝均差1.40 cm,迟角绝均差4.29°,M2分潮振幅绝均差为3.55 cm,迟角绝均差为5.69°,S2分潮振幅绝均差1.72 cm,迟角绝均差8.86°,结果显示各分潮模拟结果合理,较真实地反映了渤海海域四个分潮传播情况。 相似文献
2.
台湾海峡及其邻近海域潮汐数值计算 总被引：2，自引：0，他引：2
建立二维潮波模式,模拟了台湾海峡及其邻近海域(18-30°N,110-130°E)八个主要分潮(M2、S2、K1、O1、P1、Q1、K2、N2),并利用中国大陆及环台湾岛20多个潮位站的实测资料进行验证,计算结果与实测值吻合良好.此外,给出了八个主要分潮的同潮图,并逐个讨论了潮汐特征.结果显示:⑴台湾海峡中的潮波运动是北部蜕化了的旋转潮波系统和南部的前进潮波系统共同作用的结果.⑵半日分潮南、北两支潮波在台湾海峽中部汇合,而全日分潮则在台湾海峽南部海域汇合后继续朝西南方向传播.⑶半日分潮振幅最高值发生在福建省湄洲湾—兴化湾一带,全日分潮最高值则出现在雷州半岛以东一带近岸海域.⑷N2、K2和O1、P1、Q1分潮的振幅、迟角分布分别同M2与K1分潮的整体分布趋势相似. 相似文献
3.
印度尼西亚海域潮波的数值研究 总被引：1，自引：1，他引：0
基于ROMS模式构建了模拟区域为(15.52°S-7.13°N,110.39°~134.15°E)水平分辨率为2′的潮波数值模式,分别模拟了印尼海域M2、S2、K1、O1四个主要分潮。模拟结果与29个卫星高度计交叠点上的调和常数进行比较,符合较好。M2分潮的振幅均方根差为3.4cm,迟角均方根差为5.9°;S2分潮的振幅均方根差为1.7cm,迟角均方根差为6.3°;K1分潮振幅均方根差为1.1cm,迟角均方根差为5.8°;O1分潮振幅均方根差为1.2cm,迟角均方根差为4.4°。M2、S2、K1、O1分潮向量均方根差分别为3.8cm、2.4cm、1.9cm和1.3cm,模拟结果的相对偏差在10%左右。根据计算结果分析了印尼海域的潮汐特征及潮能传播规律,结果显示:爪哇海以外的印尼海域主要为不规则半日潮区;全日潮潮能主要由太平洋传入印尼海域,而半日潮潮能则是从印度洋传入印尼海域。 相似文献
4.
利用二维非线性潮波方程组,讨论了渤黄海主要分潮(全日潮、半日潮及浅水分潮) 数值模拟中的有关问题。数值模拟中同时考虑了4个主要分潮(M2,S2,K1,O1)和两个浅水分潮(M4,MS4)。分析表明,在渤黄海潮波系统数值模拟中,稳定后选取14 d的数值模拟结果进行调和分析能够取得最佳(最合理)的调和分析结果。计算出调和常数的模拟值与实测值之差的绝对平均值:M2分潮的振幅差为4cm,迟角差为3.3°,S2分潮的振幅差为2cm,迟角差为4.2°,K1 分潮的振幅差为1cm,迟角差为3.7°,O1分潮的振幅差为2 cm,迟角差为5.5°。实验结果较好地体现了渤黄海潮波系统的特征。 相似文献
5.
建立二维潮波模式,模拟了台湾海峡及其邻近海域（18～30°N,110～130°E）八个主要分潮（M2、S2、K1、O1、P1、Q1、K2、N2）,并利用中国大陆及环台湾岛20多个潮位站的实洲资料进行验证,计算结果与实测值吻合良好。此外,给出了八个主要分潮的同潮图,并逐个讨论了潮汐特征。结果艟示：（1）台湾海峡中的潮波运动是北部蜕化了的旋转潮波系统和南部的前进潮波系统共同作用的结果。（2）半日分潮南、北两支潮波在台湾海峡中部汇合,而今日分潮则在台湾海峡南部海域汇合后继续朝西南方向传播。（3）半日分潮振幅最高值发生在福建省湄洲湾－兴化湾一带,全日分湖最高值则出现在雷州半岛以东一带近岸海域。（4）N2、K2和O1、P1、Q1分湖的振幅、迟角分布分别同M2与K1分潮的整体分布趋势相似。 相似文献
6.
马六甲海峡是亚洲东南部的重要海峡通道,沟通太平洋和印度洋,具有重要的经济和战略地位.本文利用马六甲海峡及其毗邻海域验潮站的实测水位资料,分析了马六甲海峡及马来半岛东岸的潮汐特征.研究表明,半日分潮平均振幅最大的区域位于马六甲海峡内部,而全日分潮平均振幅最大的区域为马来半岛的东海岸.马六甲海峡内部以正规半日潮为主,马来半岛东侧则为混合潮港,北部为不正规全日潮,南部则为不规则半日潮.半日分潮M2,S2和全日分潮K1在马六甲海峡内的传播为自西北向东南,而全日分潮O1则为自东南向西北方向.马来半岛东岸的半日潮传播方向以中部的Cendering站为分界线,南、北两部海区分别向南、向北相背传播,而全日潮传播方向相同,统一为自北向南. 相似文献
7.
应用短期资料的潮流准调和分析方法,对后水湾网箱养殖区五测站两周日海流观测获得的表、中、底层海流资料进行了分析,计算了五测站O1、K1、M2、S2、M4、MS46个主要分潮的潮流调和常数,并给出了各测站在各层的潮流椭圆要素。计算结果表明:后水湾主要为日潮流海区,从最北的海区边缘向湾内靠近避风锚地,潮流性质由不规则全日潮流变为不规则半日潮流;从湾口到湾内,各分潮北分量基本以全日潮流K1为主,其次为全日潮流O1和半日潮流M2,主要分潮的振幅逐渐降低,且越靠近湾内,浅水分潮的作用越大;各分潮东分量仍以全日潮流为主,但半日潮流的作用增大,可以达到与全日潮流相当的作用。观测期间最大余流值基本出现在中层,且处于两个开边界的F1和F5站位的余流值明显大于其它站位;各站位的表层余流基本指向西北-北-东北向,即朝向湾外;而中、底层余流基本指向西南-南-东南向,即朝向湾内,通过上、下层海水的运动,海区内物质最终可以向湾外输运。整个海区可能最大流速表层在29~70 cm/s之间;中层在43~62 cm/s之间;底层在30~47 cm/s之间。表层海水基本为逆时针的旋转流运动;而中、底层海水由于一直受到邻昌礁的约束,基本为往复流运动。 相似文献
8.
收集了近年来鳌江口附近海域多个工程不同阶段5个潮位站的3-5年潮位实测数据和部分海流实测资料,通过对鳌江口附近海域的不同年份的水位资料进行潮汐调和常数分析,鳌江近海海域主要为半日潮区,其中M2分潮的振幅在170~193 cm;迟角在260°~280°之间,这些站的2007年、2010年、2011年调和常数分析结果相比,主要的半日分潮M2、S2、N2,全日分潮K1、O1及浅水分潮M4、MS4、及M6等分潮振幅、迟角的最大变化分别在1.8~4.4 cm和3°~7°之间。在初步掌握了鳌江口潮汐潮流特征的基础上,采用无结构的三角形网格和有限体积法的FVCOM海洋数值模型,进行模拟结果验证,计算结果与实测数据符合良好。构建重点年份建设工程合拢产生新的岸线水深的潮汐潮流场,刻画鳌江口建设工程的叠加影响。 相似文献
9.
收集了近年来鳌江口附近海域多个工程不同阶段5个潮位站的3~5年潮位实测数据和部分海流实测资料,通过对鳌江口附近海域的不同年份的水位资料进行潮汐调和常数分析,鳌江近海海域主要为半日潮区,其中M2分潮的振幅在170 cm~193 cm;迟角在260°~280°之间,这些站的2007年、2010年、2011年调和常数分析结果相比,主要的半日分潮M2、S2、N2,全日分潮K1、O1及浅水分潮M4、MS4、及M6等分潮振幅、迟角的最大变化分别在1.8 cm~4.4 cm和3°~7°之间。在初步掌握了鳌江口潮汐潮流特征的基础上,采用无结构的三角形网格和有限体积法的FVCOM海洋数值模型,进行模拟结果验证,计算结果与实测数据符合良好。构建重点年份建设工程合拢产生新的岸线水深的潮汐潮流场,刻画鳌江口建设工程的叠加影响。 相似文献
10.
西北太平洋的一种潮汐数值同化模型 总被引：1，自引：1，他引：0
利用FVCOM海洋数值模式,在球坐标系统下考虑非线性效应和天体引潮力的影响,基于非结构的三角形网格建立了包括中国近海、日本海、鄂霍次科海和部分西北太平洋海域的高分辨率海洋潮汐数值模型,并采用趋近法同化84个沿岸验潮站的观测资料。模拟结果与175个验潮站的实测结果拟合良好,M2,S2,K1,O1四个主要分潮振幅和迟角的绝对平均误差分别为4.0 cm和5.6°,2.4 cm和7.5°,2.6 cm和6.3°,1.5 cm和5.0°。依据调和分析结果给出了4个主要分潮的同潮图分布,得到8个半日分潮和5个全日分潮的无潮点,证实了宗谷海峡全日潮无潮点的存在,首次模拟得到津轻海峡的全日潮无潮点;还给出了整个计算海域内最大可能潮差和潮汐余水位的分布特征。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
19.
20.
《海洋学报(英文版)》2014,(11):161-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology, 相似文献