共查询到20条相似文献，搜索用时 593 毫秒
1.
2.
乌东德水电站右岸地下厂房随机块体特征研究 总被引：1，自引：0，他引：1
随机块体的几何特征和稳定性是水利水电工程中地下厂房支护设计的重要依据。对乌东德水电站右岸地下厂房随机块体的特征进行了深入研究。对研究区域内实测的裂隙参数进行了分组统计,确定了各组裂隙产状、迹长等参数的分布形式和大小。利用逆建模方法建立了三维裂隙网络模型,获取了各组裂隙的直径和三维密度。采用一般块体方法对地下厂房进行随机块体的识别和稳定性分析,利用GeneralBlock软件进行了10次随机实现,对10次计算结果进行了统计分析和讨论。研究结果表明,结构面与开挖面形成的随机块体集中在地下厂房的顶拱部位,10次随机实现中,地下厂房全长范围内平均每次形成的随机块体为414个;随机块体的平均体积为2.9 m3,最大块体的体积达152.0 m3;可移动块体中,大部分为稳定块体,不稳定块体均以坠落形式破坏;构成可移动块体的结构面多为3~4条,最多可达12条,其中倾W向的中等倾角裂隙是构成块体并可能造成块体失稳的最危险结构面;随机块体的平均深度为1.2 m,最大深度为8.8 m。建议支护锚杆应尽量穿透倾W向中等倾角的长大裂隙,且锚杆支护长度大于8.8 m。 相似文献
3.
班公湖-怒江带作为羌塘地块与拉萨地块晚中生代聚合而形成巨型构造带,其形成时代与如何汇聚是构造研究关键所在。本次研究选择班公湖—怒江带中段的安多—聂荣地块发育为研究区,对地块内部基底发育的近东西走向的韧性剪切带,开展了韧性剪切变形分析与同构造年代学研究。剪切带面理和线理测量分析指示北东—南西向构造挤压,其同构造矿物40Ar/39Ar的测试分析获得年龄约为167 Ma,表明班公湖-怒江带中段形成于中侏罗世中期北东—南西向汇聚的构造背景下。结合区域构造分析,东亚大陆西缘羌塘地块与拉萨地块在中侏罗世中期以北东—南西向碰撞聚合的构造方式完成大陆拼接,为东亚大陆西缘中侏罗世变形提供了直接构造证据。 相似文献
4.
《Geomechanics and Geoengineering》2013,8(3):171-183
Block detection is one of the most important steps in all discontinuous methods of analysis like Discontinuous Deformation Analysis (DDA) and Discrete Element Method (DEM). This is in fact a pre-processing step for those methods. In this study, a comprehensive computational algorithm, for tracing rock block created by discontinuities, has been developed. Using square matrices with integer elements and performing edge regularization step, reduce the size of the matrices due to elimination of unnecessary edges and vertices. Therefore speed and accuracy of block tracing operation will be increased. This algorithm is able to trace and identify all kind of blocks including convex and concave blocks formed by limited or unlimited fractures. The algorithm was programmed in C#.Net by over 3400 code lines and some cases were modeled by the code as example. 相似文献
5.
Because of the simplicity and the speed of execution, methods used in static stability analyses have yet remained relevant. The key‐block method, which is the most famous of them, is used for the stability analysis of fractured rock masses. The KBM method is just based on finding key blocks, and if no such blocks are found to be unstable, it is concluded that the whole of the rock mass is stable. Literally, though groups of ‘stable’ blocks are taken together into account, in some cases, it may prove to be unstable. An iterative and progressive stability analysis of the discontinuous rock slopes can be performed using the key‐group method, in which groups of collapsible blocks are combined. This method is literally a two‐dimensional (2D) limit equilibrium approach. Because of the normally conservational results of 2D analysis, a three‐dimensional (3D) analysis seems to be necessary. In this paper, the 2D key‐group method is developed into three dimensions so that a more literal analysis of a fractured rock mass can be performed. Using Mathematica software, a computer program was prepared to implement the proposed methodology on a real case. Then, in order to assess the proposed 3D procedure, its implementation results are compared with the outcomes of the 2D key‐group method. Finally, tectonic block No.2 of Choghart open pit mine was investigated as a case study using the proposed 3D methodology. Results of the comparison revealed that the outcomes of the 3D analysis of this block conform to the reality and the results of 2D analysis. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
6.
This paper presents a generalized procedure for the identification of rock blocks formed by finite‐sized fractures around complex excavations. It was assumed that the study domain could be partitioned into a finite number of subdomains, where each either was, or could be, approximated by a convex polyhedron, and the fractures were finite in size and disc shaped and were defined using the location of the disc center, orientation, radius, cohesion coefficient, and friction angle. These may be either deterministic fractures obtained from a field survey or random fractures generated by stochastic modeling. In addition, the rock mass could be heterogeneous; i.e. the rock matrix and individual fractures could have different parameters in different parts. The procedure included: (1) partitioning of the model domain into convex subdomains; (2) removing noncontributive fractures. A fracture was deemed contributive when it played a part in block formation; i.e. it formed at least one surface with some of the blocks; (3) decomposing the subdomains into element blocks with fractures; (4) restoring the infinite fractures to finite discs; and (5) assembling the modeling domain. Our procedure facilitates robust computational programming, and is flexible in dealing with the problem of a complex study domain and with rock heterogeneity. A computer code was developed based on the algorithm developed in this study. The algorithm and computer program were verified using an analytical method, and were used to solve the problem of block prediction around the underground powerhouse of the Three Gorges Project. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
7.
裂隙岩体一般块体理论初步 总被引：9，自引：0，他引：9
本文在前人工作的基础上提出了一种通用方法解决任意大小裂隙、任意形状工程岩体的岩石块体识别及稳定性计算问题。在这一方法中裂隙既可以是实测裂隙也可以是通过随机模拟方法生成的随机裂隙,工程岩体可以是任意由多面体组合成的形状,如复杂边坡或地下洞室,而且岩体和裂隙面可以是非均质的。这一通用过程被称为一般块体理论。它克服了关键块体理论(或楔形体法)中存在的弱点:即把裂隙假设为无限大的不连续面,因此无法预测岩石块体的数量和位置,而且一般只能识别出简单形状的凸形体。它在块体识别的同时将复杂的块体分解为几个简单的凸形块体,从而使复杂块体的几何描述、体积及重力计算、力学分析、可视化表示等一系列问题大大简化。在对一公路边坡的裂隙进行了详细观测之后,利用本文的方法进行了块体识别和稳定性分析,对本文的研究进行初步的验证。 相似文献
8.
《Geomechanics and Geoengineering》2013,8(4):255-262
In this study, the probabilistic key block analysis was applied to evaluate the stability of a mine ventilation shaft developed in a rock mass of granite. The key blocks were identified based on the block theory. The variations of discontinuity orientations were fitted with the Beta distribution and taken into consideration. The key block forming probabilities were analyzed. For simplification of calculations the first-order second-moment (FOSM) approximation was employed for probability estimation. With the considerations of the rock properties as random variables and applications of several statistical analysis tools, the key block failure probabilities, the probabilistic distribution of safety factors, and the probabilistic distribution of potential maximum key block volumes were analyzed. The analysis indicated that although the safety factor calculated based on the mean values of the variables was above 1.0 for the stability of the most critical key block, the block had a considerable probability of failure with a significant rock volume due to variations in discontinuity orientations and rock properties. Without promptly applying supports to the rock excavation, the shaft had a significant likelihood of failure. 相似文献
9.
This paper proposes an extension to the key‐block method, called ‘key‐group method’, that considers not only individual key blocks but also groups of collapsable blocks into an iterative and progressive analysis of the stability of discontinuous rock slopes. The basics of the key‐block method are recalled herein and then used to prove how key groups can be identified. We reveal that a key group must contain at least one basic key block, yet this condition is not entirely sufficient. The second block candidate for grouping must be another key block or a block whose movement‐preventing faces are common to one or more single key blocks. We also show that the proposed method yields more realistic results than the basic key‐block method and a comparison with results obtained using a distinct element analysis demonstrates the ability of this new method. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
10.
应用构造运动学理论,以地质、地球物理和钻井资料为基础,对汤原断陷基底和各断块体的运动特征进行研究,证实断陷内第Ⅳ块体的基底伸展量最大,第Ⅴ块体的基底伸展量最小;通过对15个块体的实例计算总结出不同构造、不同时期断块体的翘倾运动程度存在很大差异;汤原断陷构造运动控制了油气藏类型.伸展运动和压扭性挤压运动形成构造油气藏,伸展运动早、中期在向斜部位形成岩性油气藏,断块体翘倾运动和抬升剥蚀作用形成地层油气藏. 相似文献
11.
12.
由于沿空留巷服务时间较长,巷道围岩变形较大,合理地计算巷旁充填体宽度至关重要。根据沿空留巷上覆岩层的活动规律,建立了关键块和直接顶的力学模型,分析了关键块与沿空留巷围岩相互作用机制,推导出巷旁支护阻力的计算公式,并引入了关键块稳定性系数K1、K2及其稳定性影响因素的敏感度。研究结果表明,当K1>1时,关键块发生挤压变形失稳;当K2>1时,关键块发生滑落失稳。以淮南谢一矿512（5）工作面为工程背景,确定了合理的巷旁充填体宽度,计算出关键块稳定性系数,获得了各影响因素对关键块稳定性的敏感度。实例分析表明,采高对关键块的稳定性影响较大,在大采高工作面中进行沿空留巷较为困难。 相似文献
13.
Block detection is one of the important steps in all discontinuous methods of analysis such as discontinuous deformation analysis and discrete element method. It is in fact a pre‐processing step for these methods. This paper describes a new approach to the problem of geometrically defining polyhedral rock blocks created by the intersection of planar discontinuities in a rock mass. An approach is developed based on the concept of using matrices with integer elements that mostly represent vertices, edges, or face numbers and their connections. Using square matrices with integer elements and performing edge/face regularization reduce the size of the matrices because of elimination of unnecessary faces, edges, and vertices; speed and accuracy of block tracing operation will be increased. This algorithm is able to trace and identify all kinds of blocks including convex and concave blocks formed by limited or unlimited fractures. The simplicity of the procedure makes it very attractive. The algorithm was programmed in C#.Net by over 8100 code lines; several examples are presented to show application of the algorithm in different situations. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
14.
大型地下洞室群关键块体地震响应分析 总被引：1，自引：1，他引：0
基于块体理论,针对地下厂房围岩中的关键块体,采用Newmark法进行了地震响应特征和稳定性评价方法的研究,研究表明,三向地震荷载组合作用下,在块体上引起的数值较大、作用时间很短的惯性力是关键块体产生永久位移的根本原因。块体在不同烈度地震荷载作用下其响应特征不只发生量的变化,还有运动规律、模式方面的变化。研究还发现,关键块体地震响应特征与其几何特征存在一定的相关性,并由此建立了大型地下洞室群围岩地震稳定分析的多因素、多指标评判方法。最后考虑结构面的退化效应,研究了块体地震响应特征关于结构面强度参数的敏感性,获得了一些有益的结论。 相似文献
15.
风化壳型矿床的资源储量,大多采用水平投影地质块段法进行估算,目前划分地质块段的原则与方法尚不统一。以云南省武定县梅子箐风化壳型钛铁砂矿V1号矿体由78个钻孔控制的南矿段为研究实例,对划分地质块段的主要参数——矿体铅直厚度(m)、钛铁矿含量(kg/m3)、金红石含量(kg/m3)进行数理统计与图解分析,提出划分地质块段的方法。具体方法是：(1)以勘查网中地理位置相邻的3个或4个探矿工程围成的区域,作为划分地质块段的基本区块;(2)对单工程、基本区块的主要参数进行统计与计算,对基本区块的主要参数、关键参数进行图解分析;(3)将地理位置相邻、关键参数类型相同的基本区块进行归并,得出合理的地质块段划分方案。该方法能够合理地控制地质块段数量,优化地质块段划分方案,科学合理、简单易行,可在风化壳型钛铁砂矿和其他风化壳型矿床中推广使用。 相似文献
16.
煤层气井排采动态主控地质因素分析 总被引：3，自引：0，他引：3
沁水盆地寿阳区块和柿庄区块煤层气(CBM)井的排采动态在整体上表现出明显差异,而单一区块内部煤层气井的排采动态也存在较大差异。本文就两个区块的煤系地层沉积相、煤层渗透率、断裂构造、地应力类型和构造应力强度以及顶底板岩性组合类型等因素对排采动态的影响开展对比分析。基于静态地质条件和排采动态资料的综合研究表明:煤系地层沉积相、煤层渗透率、地应力类型和构造应力强度的差异是两个区块煤层气井排采动态差异的主要原因;单一区块内煤层气井的排采动态差异受控于局部断裂构造、地应力类型以及煤层顶底板岩性组合类型等局部因素;在煤层气开发选区和开发井位部署时,应综合考虑资源量、渗透率和多种局部地质因素的共同影响。 相似文献
17.
重庆武隆鸡尾山滑坡视向滑动机制分析 总被引：8，自引：0，他引：8
重庆武隆鸡尾山山体为典型的斜倾厚层灰岩山体,其破坏模式不同于常见侧向崩塌-堆积层滑坡,属于真倾向滑移变形转为视向整体滑动的特殊失稳模式。在现场地质调查的基础上,从地层岩性、岩体结构、岩溶及地下水作用、软弱夹层等影响因素分析重庆武隆鸡尾山滑坡形成原因;根据滑坡破坏机制,基于关键块体控制理论,对鸡尾山滑坡进行三维稳定性极限平衡分析;利用三维离散元软件模拟鸡尾山滑坡的初始变形破坏过程,分析了鸡尾山滑坡不同影响因素条件下的视向滑动形成机制和变形破坏特征,并探讨了节理化和溶蚀岩体的参数取值。结果分析认为,在重力的长期作用下,鸡尾山山体初始沿真倾向方向滑移,沿岩溶发育的陡倾节理裂隙逐渐产生后缘及侧向裂缝,形成块状后部驱动块体,由于地下水等因素使软弱夹层软化,驱动块体下滑力增大,前缘阻滑关键块体内部应力积累,并最终沿强度较低的岩溶发育带发生剪切破坏,从而导致整体滑动;在进行滑坡稳定性极限平衡分析时,考虑实际的滑坡机制,将滑体分为驱动块体和关键块体分别进行力的解析,并以关键块体的安全系数代表滑坡的安全系数更加合理。数值模拟显示,软弱夹层强度降低、岩溶发育带剪切破坏后,滑体进入大变形阶段,表明关键块体控制和阻滑作用明显,软弱夹层强度降低是滑坡发生的关键因素。采矿形成的采空区对山体的影响主要是使上覆岩体压应力增大,但对滑体的变形无影响。 相似文献
18.
岩质边坡关键块体的搜索方法及工程应用 总被引：1，自引：0，他引：1
工程边坡开挖所揭露的某些结构面组合块体在破坏原有静力平衡状态后,进行应力重新分配,进而块体会发生失稳、滑动等变形,甚至影响到整个边坡发生破坏,因此,结构面组合块体的稳定性是决定岩质边坡稳定的重要因素。本文通过对某工程开挖边坡地形和结构面三维实体模型的建立,实现了边坡结构面与开挖地形实体模型在AutoCAD平台上的可视化操作,剖切不同位置的二维图形预测分析了边坡开挖后可能存在的结构面组合块体,采用块体计算程序(Swegde)验证关键块体并进行稳定性评价。结果表明:三维实体模型及剖切技术与块体计算方法的结合,易于搜索关键块体。事实证明,该方法操作简便,计算结果准确,搜索方法具备可行性。 相似文献
19.
从古地磁研究看中国大陆形成与演化过程 总被引：12，自引：1，他引：11
古地磁学是进行大陆板块或微板块(地块)运动演化过程和古地理重建的最有效手段之一。近半个世纪以来,通过中外学者艰苦卓绝的努力,在中国大陆上积累了大量的古地磁数据,为中国大陆各主要块体的起源、构造演化和碰撞拼合过程等提供了定量约束。文中根据现代古地磁数据可靠性判别标准,对扬子、华北及塔里木地块显生宙古地磁数据进行了重新分析和筛选,结合拉萨和喜马拉雅地块的古地磁数据,对中国大陆的形成和演化提出了几点认识:(1)古生代中国大陆各主要块体基本位于赤道附近的低纬度地区;早古生代扬子、华北及塔里木地块与东冈瓦纳大陆关系密切;(2)中生代是中国大陆各主要块体发生碰撞和拼合的主要时期;(3)中国大陆主要块体间的碰撞和拼合具有局部首先碰撞、相互旋转、完全拼合、陆内挤压造山和伸展反弹的特点。 相似文献