首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 406 毫秒
1.
The Kazhdumi Formation of the Bangestan Group is a well-known source rock that has produced abundant oil in most petroleum fields in the Zagros Basin, which stretches from northwest to southwest Iran over hundreds of kilometres. The formation reaches a thickness of 230 m at the type section in northwest Zagros but thins out to 40–50 m in wells studied from the South Pars giant petroleum field, where it comprises mainly grey shales with occasional intercalations of marls and sandstones. South Pars, best known as the Iranian part of the world's largest non-associated gas field, contains small quantities of oil above and below the Kazhdumi Formation.  相似文献   

2.
Phase fractionation can strongly deplete oil of its volatile compounds in a regular and characteristic fashion. This process has affected oils to a remarkably uniform extent throughout the 30 × 15 km South Marsh Island 208–239 and Vermilion 30–31 area (including the Tiger Shoal, Starfak, Mound Point, Lighthouse Point, Amber, Trinity Shoal, and Aquamarine fields) just offshore Louisiana. Fractionation of the original “parent” oil likely occurred in the deep, relatively flat-lying Rob L sand that underlies the area, and produced gas-washed oils (mean API 33°) and gas condensates (mean API 50°) in a volume ratio of 1:3.5. Both fractionated oil and vapor migrated from the fractionation site to shallower reservoirs. However, the estimated ultimate production ratio of gas-washed oil to gas condensate in this group of fields is 1:0.32, about 11 times higher than would be expected on mass balance considerations alone. Thus, there is an apparent deficiency of producible gas condensate relative to the amount of producible oil for the entire study area and for every field in that area. In the case of the Tiger Shoal field, the ratio of industry-estimated ultimately producible oil to gas condensate is 1:1.1. Based on the production data, we conclude that either there is an additional 6.4 × 106 m3 (43 MMbbl) of undiscovered and/or unproduced condensate in the area or that condensate has escaped preferentially in vapor form to the seafloor. The well-studied and nearly depleted Tiger Shoal field provides a good example of how chemical data can be analyzed in a way that contributes insight into the phase fractionation process and the remaining exploration potential of an area.  相似文献   

3.
The first exploratory well, the ZS1C well, with 158,545 m3 daily gas production was discovered in 6861–6944 m deep strata of the Cambrian gypsolyte layer of the Tarim Basin, China in 2014. The discovery opens a new target for the Cambrian-reservoired oil and gas exploration, and directly leads to large-scale oil and gas exploration of the deep-reservoired Cambrian oil and gas fields in the Basin. Comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry and a comprehensive two-dimensional gas chromatography–flame ionization detector revealed the presence of abundant adamantane compounds, 2-thiaadamantanes and 2-thiadiamantanes, and a large amount of sulfur-containing compounds in the condensate oil. The formation of organic sulfur-containing compounds, such as 2-thiaadamantanes, is an indication of sulfur incorporation from the gypsum in the stratum into oil and gas in the course of TSR. This reservoir has apparently suffered severe TSR alteration because (1) High content of H2S, (2) H2S sulfur isotopes, (3) CO2 carbon isotopes, and others abundant data to support this findings. Similar sulfur isotopic composition of H2S, oil condensate and the gypsum in the Cambrian strata indicate that the produced condensate is experienced TSR alteration. Therefore, the deep-accumulated Cambrian oil reservoir has experienced severe TSR alteration, and accumulated natural gas and condensate contains high sulfur content.  相似文献   

4.
The Ordovician is the most important exploration target in the Tabei Uplift of the Tarim Basin, which contains a range of petroleum types including solid bitumen, heavy oil, light oil, condensate, wet gas and dry gas. The density of the black oils ranges from 0.81 g/cm3 to 1.01 g/cm3 (20 °C) and gas oil ratio (GOR) ranges from 4 m3/m3 to 9300 m3/m3. Oil-source correlations established that most of the oils were derived from the Mid-Upper Ordovician marine shale and carbonate and that the difference in oil properties is mainly attributed to hydrocarbon alteration and multi-stage accumulation. In the Tabei Uplift, there were three main periods of hydrocarbon accumulation in the late Caledonian stage (ca. 450–430 Ma), late Hercynian stage (ca. 293–255 Ma) and the late Himalayan stage (ca. 12–2 Ma). The oil charging events mainly occurred in the late Caledonian and late Hercynian stage, while gas charging occurred in the late Hercynian stage. During the late Caledonian stage, petroleum charged the reservoirs lying east of the uplift. However, due to a crustal uplifting episode in the early Hercynian (ca. 386–372 Ma), most of the hydrocarbons were transformed by processes such as biodegradation, resulting in residual solid bitumen in the fractures of the reservoirs. During the late Hercynian Stage, a major episode of oil charging into Ordovician reservoirs took place. Subsequent crustal uplift and severe alteration by biodegradation in the west-central Basin resulted in heavy oil formation. Since the late Himalayan stage when rapid subsidence of the crust occurred, the oil residing in reservoirs was exposed to high temperature cracking conditions resulting in the production of gas and charged from the southeast further altering the pre-existing oils in the eastern reservoirs. A suite of representative samples of various crude oils including condensates, lights oils and heavy oils have been collected for detailed analysis to investigate the mechanism of formation. Based on the research it was concluded that the diversity of hydrocarbon physical and chemical properties in the Tabei Uplift was mainly attributable to the processes of biodegradation and gas washing. The understanding of the processes is very helpful to predict the spatial distribution of hydrocarbon in the Tabei Uplift and provides a reference case study for other areas.  相似文献   

5.
The Upper Jurassic marlstones (Mikulov Fm.) and marly limestones (Falkenstein Fm.) are the main source rocks for conventional hydrocarbons in the Vienna Basin in Austria. In addition, the Mikulov Formation has been considered a potential shale gas play. In this paper, organic geochemical, petrographical and mineralogical data from both formations in borehole Staatz 1 are used to determine the source potential and its vertical variability. Additional samples from other boreholes are used to evaluate lateral trends. Deltaic sediments (Lower Quarzarenite Member) and prodelta shales (Lower Shale Member) of the Middle Jurassic Gresten Formation have been discussed as secondary sources for hydrocarbons in the Vienna Basin area and are therefore included in the present study.The Falkenstein and Mikulov formations in Staatz 1 contain up to 2.5 wt%TOC. The organic matter is dominated by algal material. Nevertheless, HI values are relative low (<400 mgHC/gTOC), a result of organic matter degradation in a dysoxic environment. Both formations hold a fair to good petroleum potential. Because of its great thickness (∼1500 m), the source potential index of the Upper Jurrasic interval is high (7.5 tHC/m2). Within the oil window, the Falkenstein and Mikulov formations will produce paraffinic-naphtenic-aromatic low wax oil with low sulfur content. Whereas vertical variations are minor, limited data from the deep overmature samples suggest that original TOC contents may have increased basinwards. Based on TOC contents (typically <2.0 wt%) and the very deep position of the maturity cut-off values for shale oil/gas production (∼4000 and 5000 m, respectively), the potential for economic recovery of unconventional petroleum is limited. The Lower Quarzarenite Member of the Middle Jurassic Gresten Formation hosts a moderate oil potential, while the Lower Shale Member is are poor source rock.  相似文献   

6.
The effect of shale composition and fabric upon pore structure and CH4 sorption is investigated for potential shale gas reservoirs in the Western Canadian Sedimentary Basin (WCSB). Devonian–Mississippian (D–M) and Jurassic shales have complex, heterogeneous pore volume distributions as identified by low pressure CO2 and N2 sorption, and high pressure Hg porosimetry. Thermally mature D–M shales (1.6–2.5% VRo) have Dubinin–Radushkevich (D–R) CO2 micropore volumes ranging between 0.3 and 1.2 cc/100 g and N2 BET surface areas of 5–31 m2/g. Jurassic shales, which are invariably of lower thermal maturity ranging from 0.9 to 1.3% VRo, than D–M shales have smaller D–R CO2 micropore volumes and N2 BET surface areas, typically in the range of 0.23–0.63 cc/100 g (CO2) and 1–9 m2/g (N2).  相似文献   

7.
Coalbed methane (CBM) is a worldwide exploration target of the petroleum industry. In Brazil, the most important coal-bearing succession is associated with the Permian Rio Bonito Formation of the Paraná Basin. The gas-prone areas are located at the southeastern margin of the Paraná Basin and possibly in the offshore region of the northern part of the Pelotas Basin. Coalfields end abruptly at the present day shoreline, a result of rifting of Gondwana and the evolution of the South Atlantic Ocean. All geologic indicators suggest that in pre-rift times the coal seams extended further eastwards, probably now lying deeply buried below the sedimentary succession of the Pelotas Basin. The present paper discusses structural, stratigraphic, seismic and aeromagenetic data that support the preservation of continental crust beneath ocean sediment. If the coal beds had similar lateral extent to known onshore coals, and coal beds extended across the projected extension of the Parana basin, and there was a conservative 5 m of cumulative coal thickness, then a potential methane volume can be estimated for this newly inferred resource. Average onshore coal gas content is 32 scf/ton (1.00 m3/ton). If this is similar in the offshore coal deposits, then the hypothetical methane volume in the offshore area could be in excess of 1.9 × 1012 scf (56 × 109 m3). Metamorphism from dikes associated with rifting are potential complicating factors in these deposits, and since no borehole reaching the deep-lying strata in the offshore area are available, this is a hypothetical gas resource with a certain level of uncertainty which should be tested in the future by drilling a deep borehole.  相似文献   

8.
The Pearl River Mouth Basin (PRMB) and Qiongdongnan Basin (QDNB) are oil and gas bearing basins in the northern margin of the South China Sea (SCS). Geothermal survey is an important tool in petroleum exploration. A large data set comprised of 199 thermal conductivities, 40 radioactive heat productions, 543 measured geothermal gradient values, and 224 heat flow values has been obtained from the two basins. However, the measured geothermal gradient data originated from diverse depth range make spatial comparison a challenging task. Taking into account the variation of conductivity and heat production of rocks, we use a “uniform geothermal gradient” to characterize the geothermal gradient distribution of the PRMB and QDNB. Results show that, in the depth interval of 0–5 km, the “uniform geothermal gradient” in the PRMB varies from 17.8 °C/km to 50.2 °C/km, with an average of 32.1 ± 6.0 °C/km. In comparison, the QDNB has an average “uniform geothermal gradient” of 31.9 ± 5.6 °C/km and a range between 19.7 °C/km and 39.5 °C/km. Heat flows in the PRMB and QDNB are 71.3 ± 13.5 mW/m2 and 72.9 ± 14.2 mW/m2, respectively. The heat flow and geothermal gradient of the PRMB and QDNB tend to increase from the continental shelf to continental slope owing to the lithosphereic/crustal thinning in the Cenozoic.  相似文献   

9.
The Dniepr-Donets Basin (DDB) hosts a multi-source petroleum system with more than 200 oil and gas fields, mainly in Carboniferous clastic rocks. Main aim of the present study was to correlate accumulated hydrocarbons with the most important source rocks and to verify their potential to generate oil and gas. Therefore, molecular and isotopic composition as well as biomarker data obtained from 12 oil and condensate samples and 48 source rock extracts was used together with USGS data for a geological interpretation of hydrocarbon charging history.Within the central DDB, results point to a significant contribution from (Upper) Visean black shales, highly oil-prone as well as mixed oil- and gas-prone Serpukhovian rocks and minor contribution from an additional Tournaisian source. Devonian rocks, an important hydrocarbon source within the Pripyat Trough, have not been identified as a major source within the central DDB. Additional input from Bashkirian to Moscovian (?) (Shebelinka Field) as well as Tournaisian to Lower Visean rocks (e.g. Dovgal Field) with higher contents of terrestrial organic matter is indicated in the SE and NW part, respectively.Whereas oil–source correlation contradicts major hydrocarbon migration in many cases for Tournaisian to Middle Carboniferous reservoir horizons, accumulations within Upper Carboniferous to Permian reservoirs require vertical migration up to 4000 m along faults related to Devonian salt domes.1-D thermal models indicate hydrocarbon generation during Permo-Carboniferous time. However, generation in coal-bearing Middle Carboniferous horizons in the SE part of the basin may have occurred during the Mesozoic.  相似文献   

10.
The deeply buried reservoirs (DBRs) from the Lijin, Shengtuo and Minfeng areas in the northern Dongying Depression of the Bohai Bay Basin, China exhibit various petroleum types (black oil-gas condensates) and pressure systems (normal pressure-overpressure) with high reservoir temperatures (154–185 °C). The pressure-volume-temperature-composition (PVTX) evolution of petroleum and the processes of petroleum accumulation were reconstructed using integrated data from fluid inclusions, stable carbon isotope data of natural gas and one-dimensional basin modeling to trace the petroleum accumulation histories.The results suggest that (1) the gas condensates in the Lijin area originated from the thermal cracking of highly mature kerogen in deeper formations. Two episodes of gas condensate charging, which were evidenced by the trapping of non-fluorescent gas condensate inclusions, occurred between 29-25.5 Ma and 8.6–5.0 Ma with strong overpressure (pressure coefficient, Pc = 1.68–1.70), resulting in the greatest contribution to the present-day gas condensate accumulation; (2) the early yellow fluorescent oil charge was responsible for the present-day black oil accumulation in well T764, while the late blue-white oil charge together with the latest kerogen cracked gas injection resulted in the present-day volatile oil accumulation in well T765; and (3) the various fluorescent colors (yellow, blue-white and blue) and the degree of bubble filling (Fv) (2.3–72.5%) of the oil inclusions in the Minfeng area show a wide range of thermal maturity (API gravity ranges from 30 to 50°), representing the charging of black oil to gas condensates. The presence of abundant blue-white fluorescent oil inclusions with high Grain-obtaining Oil Inclusion (GOI) values (35.8%, usually >5% in oil reservoirs) indicate that a paleo-oil accumulation with an approximate API gravity of 39–40° could have occurred before 25 Ma, and gas from oil cracking in deeper formations was injected into the paleo-oil reservoir from 2.8 Ma to 0 Ma, resulting in the present-day gas condensate oil accumulation. This oil and gas accumulation model results in three oil and gas distribution zones: 1) normal oil reservoirs at relatively shallow depth; 2) gas condensate reservoirs that originated from the mixture of oil cracking gas with a paleo-oil reservoir at intermediate depth; and 3) oil-cracked gas reservoirs at deeper depth.The retardation of organic matter maturation and oil cracking by high overpressure could have played an important role in the distribution of different origins of gas condensate accumulations in the Lijin and Minfeng areas. The application of oil and gas accumulation models in this study is not limited to the Dongying Depression and can be applied to other overpressured rift basins.  相似文献   

11.
Two sets of Lower Paleozoic organic-rich shales develop well in the Weiyuan area of the Sichuan Basin: the Lower Cambrian Jiulaodong shale and the Lower Silurian Longmaxi shale. The Weiyuan area underwent a strong subsidence during the Triassic to Early Cretaceous and followed by an extensive uplifting and erosion after the Late Cretaceous. This has brought about great changes to the temperature and pressure conditions of the shales, which is vitally important for the accumulation and preservation of shale gas. Based on the burial and thermal history, averaged TOC and porosity data, geological and geochemical models for the two sets of shales were established. Within each of the shale units, gas generation was modeled and the evolution of the free gas content was calculated using the PVTSim software. Results show that the free gas content in the Lower Cambrian and Lower Silurian shales in the studied area reached the maxima of 1.98–2.93 m3/t and 3.29–4.91 m3/t, respectively (under a pressure coefficient of 1.0–2.0) at their maximum burial. Subsequently, the free gas content continuously decreased as the shale was uplifted. At present, the free gas content in the two sets of shales is 1.52–2.43 m3/t and 1.94–3.42 m3/t, respectively (under a current pressure coefficient of 1.0–2.0). The results are roughly coincident with the gas content data obtained from in situ measurements in the Weiyuan area. We proposed that the Lower Cambrian and Lower Silurian shales have a shale gas potential, even though they have experienced a strong uplifting.  相似文献   

12.
The identification of a deeply-buried petroleum-source rock, owing to the difficulty in sample collection, has become a difficult task for establishing its relationship with discovered petroleum pools and evaluating its exploration potential in a petroleum-bearing basin. This paper proposes an approach to trace a deeply-buried source rock. The essential points include: determination of the petroleum-charging time of a reservoir, reconstruction of the petroleum generation history of its possible source rocks, establishment of the spatial connection between the source rocks and the reservoir over its geological history, identification of its effective source rock and the petroleum system from source to trap, and evaluation of petroleum potential from the deeply-buried source rock. A case study of the W9-2 petroleum pool in the Wenchang A sag of the Pearl River Mouth Basin, South China Sea was conducted using this approach. The W9-2 reservoir produces condensate oil and gas, sourced from deeply-buried source rocks. The reservoir consists of a few sets of sandstone in the Zhuhai Formation, and the possible source rocks include an early Oligocene Enping Formation mudstone and a late Eocene Wenchang Formation mudstone, with a current burial depth from 5000 to 9000 m. The fluid inclusion data from the reservoir rock indicate the oil and the gas charged the reservoir about 18–3.5 Ma and after 4.5 Ma, respectively. The kinetic modeling results show that the main stages of oil generation of the Wenchang mudstone and the Enping mudstone occurred during 28–20 Ma and 20–12 Ma, respectively, and that the δ13C1 value of the gas generated from the Enping mudstone has a better match with that of the reservoir gas than the gas from the Wenchang mudstone. Results from a 2D basin modeling further indicate that the petroleum from the Enping mudstone migrated upward along the well-developed syn-sedimentary faults in the central area of the sag into the reservoir, but that the petroleum from the Wenchang mudstone migrated laterally first toward the marginal faults of the sag and then migrated upward along the faults into shallow strata. The present results suggest that the trap structure in the central area of the sag is a favorable place for the accumulation of the Enping mudstone-derived petroleum, and that the Wenchang mudstone-derived petroleum would have a contribution to the structures along the deep faults as well as in the uplifted area around the sag.  相似文献   

13.
The objectives of our study were to assess the thickness, lateral extent, organic richness and maturity of the potential source rocks in Hungary and to estimate the volumes of hydrocarbons generated, in order that potential shale gas and shale oil plays could be identified and characterised.The Upper Triassic Kössen Marl in south-west Hungary could represent the best potential shale gas/shale oil play, due to its high organic richness, high maturity and the presence of fracture barriers. The area of gas- and oil-generative maturity is around 720 km2 with the unexpelled petroleum estimated to be up to 9 billion barrel oil-equivalent.The Lower Jurassic sediments of the Mecsek Mountains and under the Great Plain contain fair quality gas-prone source rocks, with low shale gas potential, except for a thin Toarcian shale unit which is richer in organic matter. The latter could form a potential shale gas play under the Great Hungarian Plain, if it is thicker locally.The Lower Oligocene Tard Clay in north-east Hungary could represent the second best potential shale oil play, due to its organic richness, favourable maturity and large areal extent (4500 km2) with around 7 billion barrel oil-equivalent estimated in-place volume of petroleum.Middle Miocene marine formations could represent locally-developed shale gas plays; they have fair amounts of organic matter and a mixture of type II/III kerogen, but their vertical and lateral variability is high.The Upper Miocene lacustrine Endrőd Marl contains less organic matter and the kerogen is mainly type III, which is not favourable for shale gas generation. The high carbonate and clay content, plus the lack of upper and lower fracture barriers would represent additional production challenges.  相似文献   

14.
Following the discovery of asphalt volcanism in the Campeche Knolls a research cruise was carried out in 2006 to unravel the nature of the asphalt deposits at Chapopote. The novel results support the concept that the asphalt deposits at the seafloor in 3000 m of water depth originate from the seepage of heavy petroleum with a density slightly greater than water. The released petroleum forms characteristic flow structures at the seafloor with surfaces that are ‘ropy’ or ‘rough’ similar to magmatic lava flows. The surface structures indicate that the viscosity of the heavy petroleum rapidly increases after extrusion due to loss of volatiles. Consequently, the heavy petroleum forms the observed asphalt deposit and solidifies. Detailed survey with a remotely operated vehicle revealed that the asphalts are subject to sequential alterations: e.g. volume reduction leading to the formation of visible cracks in the asphalt surface, followed by fragmentation of the entire deposit. While relatively fresh asphalt samples were gooey and sticky, older, fragmented pieces were found to be brittle without residual stickiness. Furthermore, there is evidence for petroleum seepage from below the asphalt deposits, leading to local up-doming and, sometimes, to whip-shaped extrusions. Extensive mapping by TV-guided tools of Chapopote Asphalt Volcano indicates that the main asphalt deposits occur at the south-western rim that borders a central, crater-like depression. The most recent asphalt deposit at Chapopote is the main asphalt field covering an area of ∼2000 m2. Asphalt volcanism is distinct from oil and gas seepage previously described in the Gulf of Mexico and elsewhere because it is characterized by episodic intrusions of semi-solid hydrocarbons that spread laterally over a substantial area and produce structures with significant vertical relief. As Chapopote occurs at the crest of a salt structure it is inferred that asphalt volcanism is a secondary result of salt tectonism.  相似文献   

15.
Several exploration wells have intersected a Cenozoic coal-bearing, fluvial-deltaic mudstone and sandstone succession in the northeastern Vietnamese part of the Malay Basin, and have successfully tested seismically identified direct hydrocarbon indicators (DHIs). The oil and gas/condensate discovery well 46-CN-1x encountered a ∼55 m thick section of lacustrine mudstones having considerable potential as an oil source. Vitrinite reflectance (VR) measurements from these alginite-bearing rocks introduce several problems in thermal maturity evaluation, including associated VR suppression and delineation of cavings and bitumens. Reliable thermal maturity gradients, however, may be established using a combination of conventional VR measurements and ‘equivalent VR’ (EqVR) values derived from the fluorescence alteration of multiple macerals (FAMM) technique. These measurements, performed on dispersed organic matter (DOM) in cuttings from 46-CN-1x, allow separation of low-reflecting bitumens and vitrinite in cavings from indigenous vitrinite and the FAMM results indicate VR suppression of 0.14% in an alginite-bearing mudstone with a high Hydrogen Index value. On the basis of available ‘raw’ VR data, a highly irregular maturity trend is determined, with the deepest sample (2675–2680 m) having a VR of ∼0.4%Ro. The EqVR value, however, for the deepest sample is 0.70%. The maturity trend determined from the FAMM data (and VR data, omitting samples having suppressed VR) indicates that the top of the oil window (VR of 0.75%Ro) is located at about 2800 m depth. Modelling the geothermal gradient using the EASY%Ro algorithm yields ∼40 °C/km for both of the two maturity profiles; this is in the low end of the range for the Malay Basin. Modelled temperature histories indicate onset of hydrocarbon generation for the uppermost Oligocene source rocks between 2 Ma and present-day, which post-dates trap formation. Seismic facies patterns suggest that lacustrine oil-prone units are in the oil window in the same graben complex a few km NW of the investigated well, and these rocks are likely to be the source of the hydrocarbons found in the well. A more widespread occurrence of hydrocarbons sourced from this kitchen is indicated by other discoveries and mapping of DHIs in the area.  相似文献   

16.
During the past two million years low surface temperatures as well as episodically advancing ice sheets from Scandinavia acted on the subsurface pT-regime of northern Germany. Their likely effects on the petroleum system of Schleswig-Holstein were investigated. For the entire Quaternary mean annual ground temperature (MAGT) was reconstructed at a resolution of 1000 years by calibrating oxygen isotope records from ODP-site 659 to the climate of northern Germany of the past 120 kyr. The resulting MAGT trend served as input to an ice sheet model and a permafrost model along a 2D section crossing the petroleum bearing south-western part of Schleswig-Holstein. Here advances and retreats of the Scandinavian ice sheet during Saalian and Elsterian glaciation Stages were reconstructed. Maximum ice thicknesses of up to 1700 m and up to 20 periods of regional permafrost in northern Germany were reconstructed for the past 1.25 million years. Based on a basal heat flow of 50 mW/m2 permafrost thicknesses exceeded 100 m during most of these periods, temporarily extending down to depths of more than 300 m. Favourable surface temperatures and long durations of cold periods provided favourable conditions for onshore gas hydrate stability zones at Mittelplate. Implementing these glacial dynamics into 2D basin modelling (PetroMod, IES, Aachen, Germany) of the Mittelplate oil field reveals five phases of gas hydrate stability at depths down to 750 m. The latest of these events occurred during the Weichselian about 20 kyr ago. The effect of the ice sheets on pore pressure in the subsurface strongly depends on the hydraulic boundary conditions at the ice base (e.g. frozen vs. temperate ice sheet base). Excess pore pressure in the reservoir of more than 10 MPa during ice overriding is possible and probable. The calculated temperature effect of the Pleistocene cooling on the Mittelplate reservoir is in the range of 3–7 °C. Even today temperature in the reservoir is still lowered by about 4 °C in comparison to pre-Pleistocene times. Despite the fact that a significant influence of glacial effects on petroleum generation can be ruled out at Mittelplate, we state that pT-effects in reservoirs related to glacial processes in formerly glaciated areas have been underestimated in the past.  相似文献   

17.
A. Zabanbark 《Oceanology》2009,49(5):729-739
The Bering Sea sedimentary basin comprises the Bering Sea and the adjacent intermontane depressions on the continents. It includes the following subordinate sedimentary basins: the Norton; Bethel; Saint Lawrence; Anadyr; Navarin; Khatyrka; Saint George; Bristol; Cook Inlet; and Aleutian consisting of the autonomous Aleutian, Bowers, and Komandor basins. All of them exhibit significant geological similarity. The Middle and Upper Miocene terrigenous sequences, which are petroliferous through the entire periphery of the Pacific Ocean, are characterized by their high petroleum resource potential in the Bering Sea continental margin as well, which is confirmed by the oil and gas pools discovered in neighboring onshore lowlands. The younger (Pliocene) and older (up to Upper Cretaceous) sedimentary formations are also promising with respect to hydrocarbons. The integral potential oil and gas resources of the Bering Sea sedimentary basin, including the continental slopes, are estimated by the US Geological Survey to be 1120 × 106 t and 965 × 109 m3, respectively.  相似文献   

18.
The effect of dissolved petroleum hydrocarbons in the environment on phytoplankton biomass measured as chlorophyll a was studied near the oil tanker route in the southern Bay of Bengal. In the transect from 5° N, 77° E to 5° N, 87° E the concentrations of dissolved petroleum hydrocarbons were negatively correlated with phytoplankton biomass, whereas in the 0° N, 87° E to 1° N, 79° E transect they were positively correlated with phytoplankton biomass. The mean petroleum hydrocarbon concentrations in the two transects were 12·12 ± 4·67 μg litre−1 and 11·23 ± 4·5 μg litre−1, respectively.It is surmised that the effect of dissolved petroleum hydrocarbons on phytoplankton biomass varies depending on the nature rather than the quantity of petroleum hydrocarbons present. Culture studies with unialgal Nitzschia sp. in seawater collected from selected stations in the study area as well as in artificial seawater spiked with the water-soluble petroleum hydrocarbon fraction of light Arabian Crude support this.  相似文献   

19.
About 120 gas seepage vents were documented along the west and southwest coast of the Hainan Island, South China Sea, in water depths usually less than 50 m. The principal seepage areas include the Lingtou Promontory, the Yinggehai Rivulet Mouth, Yazhou Bay, the Nanshan Promontory and the Tianya Promontory. They occur along three major zones, reflecting the control by faults and lateral conduits within the basement. It is estimated that the total gas emission from these seepage vents is 294–956 m3/year. The seepage gases are characterized by a high CH4 content (76%), heavy δ13C1 values (−38 to −33‰) and high C1/C1–5 ratios (0.95–1.0), resembling the thermogenic gases from the diapiric gas fields of the Yinggehai Basin. Hydrocarbon–source correlation shows that the hydrocarbons in the sediments from seepage areas can be correlated with the deeply buried Miocene source rocks and sandstone reservoirs in the central depression. The 2D basin modeling results based on a section from the source rock center to the gas seepage sites indicate that the gas-bearing fluids migrated from the source rocks upward through faults or weak zones encompassed by shale diapirism or in up-dip direction along the sandstone-rich strata of Huangliu Formation to arrive to seabed and form the nearshore gas seepages. It is suggested that the seepage gases are sourced from the Miocene source rocks in the central depression of the Yinggehai Basin. This migration model implies that the eastern slope zone between the gas source area of the central depression and the seepage zone is also favorable place for gas accumulation.  相似文献   

20.
The Qiangtang Basin is a significant prospective area for hydrocarbon and gas hydrate resources in the Tibetan Plateau, China. However, relatively little work has been performed to characterise heat flow in this basin, which has restricted petroleum and gas hydrate exploration. In this study, we compare present and palaeo-heat flow in the Qiangtang Basin to provide information on geothermal regime, hydrocarbon generation and permafrost that is necessary for further petroleum and gas hydrate exploration. We base our study on temperature data from a thermometer well, thermal conductivity tests, vitrinite reflectance data, homogenisation temperature data from fluid inclusions, stratigraphic information and a time-independent modelling approach. Our results indicate that in the central Qiangtang Basin, the present thermal gradient is approximately 15.5 °C/km, and heat flow is approximately 46.69 mW/m2. Heat flow in the Qiangtang Basin is not relatively stable since the Early Jurassic, as previous research has suggested, and it is generally decreasing with time. Additionally, there is a clear difference between the hottest thermal regime of the southern and northern Qiangtang Depressions during Cretaceous to Pleistocene time. In the southern Qiangtang Depression, the palaeogeothermal gradient is approximately 32.0 °C/km, and palaeo-heat flow is approximately 70 mW/m2. However, in the northern Qiangtang Depression, the palaeogeothermal gradient exceeds 81.8 °C/km, and palaeo-heat flow is greater than 172.09 mW/m2. The high thermal regime in the northern Qiangtang Depression is driven mainly by hydrothermal convection. Gas reservoirs are possible targets for hydrocarbon exploration in this depression. Currently, the northwestern part of the northern Qiangtang Depression is the most favourable area for gas hydrate exploration in the Qiangtang Basin.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号