首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
During geothermal power production using a borehole doublet consisting of a production and injection well, the reservoir conditions such as permeability k, porosity φ and Skempton coefficient B at the geothermal research site Gross Schoenebeck/Germany will change. Besides a temperature decrease at the injection well and a change of the chemical equilibrium, also the pore pressure p p will vary in a range of approximately 44 MPa ± 10 MPa in our reservoir at ?3850 to ?4258 m depth. This leads to a poroelastic response of the reservoir rocks depending on effective pressure p eff (difference between mean stress and pore pressure), resulting in a change in permeability k, porosity φ and the poroelastic parameter Skempton coefficient B. Hence, we investigated the effective pressure dependency of Flechtinger sandstone, an outcropping equivalent of the reservoir rock via laboratory experiments. The permeability decreased by 21% at an effective pressure range from 3 to 30 MPa, the porosity decreased by 11% (p eff = 6 to 65 MPa) and the Skempton coefficient decreased by 24% (p eff = 4 to 25 MPa). We will show which mechanisms lead to the change of the mentioned hydraulic and poroelastic parameters and the influence of these changes on the productivity of the reservoir. The most significant changes occur at low effective pressures until 15 to 20 MPa. For our in situ reservoir conditions p eff = 43 MPa a change of 10 MPa effective pressure will result in a change in matrix permeability of less than 4% and in matrix porosity of less than 2%. Besides natural fracture systems, fault zones and induced hydraulic fractures, the rock matrix its only one part of geothermal systems. All components can be influenced by pressure, temperature and chemical reactions. Therefore, the determined small poroelastic response of rock matrix does not significantly influence the sustainability of the geothermal reservoir.  相似文献   

2.
致密砂岩气藏具有裂缝发育和有效应力高的特征,研究不同有效压力下孔、裂隙介质地震波传播特征,有利于地震解释与地下储层的识别.但是前人的研究较少考虑岩石内部微观孔隙结构特征与孔隙、裂隙间流体流动的关系.本文首先通过选取四川盆地典型致密砂岩岩样,在不同有效压力下对岩石样本进行超声波实验测量.然后基于实验测得的纵、横波速度进行裂隙参数反演,得到不同有效压力下致密砂岩样本的裂隙孔隙度.再将裂隙孔隙度和样本岩石物理参数代入双重孔隙介质模型,模拟得到不同有效压力下饱水致密砂岩样本纵横波速度频散和衰减的变化规律.结果表明模型预测的速度频散曲线与纵波速度实验测量结果能够较好的吻合.最后统计分析了致密砂岩裂隙参数,得到了致密砂岩储层裂隙参数随有效压力及孔隙度变化特征.依据实际岩石物理参数建立模型,其裂隙参数三维拟合结果能够较好描述致密砂岩裂隙结构与孔隙度、应力的关联,可为实际地震勘探中预测储层裂缝性质提供基础依据.  相似文献   

3.
Adopting the method of forced oscillation, attenuation was studied in Fontainebleau sandstone (porosity 10%, permeability 10 mD) at seismic frequencies (1–100 Hz). Confining pressures of 5, 10, and 15 MPa were chosen to simulate reservoir conditions. First, the strain effect on attenuation was investigated in the dry sample for 11 different strains across the range 1 × 10?6–8 × 10?6, at the confining pressure of 5 MPa. The comparison showed that a strain of at least 5 × 10?6 is necessary to obtain a good signal to noise ratio. These results also indicate that nonlinear effects are absent for strains up to 8 × 10?6. For all the confining pressures, attenuation in the dry rock was low, while partial (90%) and full (100%) saturation with water yielded a higher magnitude and frequency dependence of attenuation. The observed high and frequency dependent attenuation was interpreted as being caused by squirt flow.  相似文献   

4.
Synthetic rock samples can offer advantages over natural rock samples when used for laboratory rock physical properties studies, provided their success as natural analogues is well understood. The ability of synthetic rocks to mimic the natural stress dependency of elastic wave, electrical and fluid transport properties is of primary interest. Hence, we compare a consistent set of laboratory multi-physics measurements obtained on four quartz sandstone samples (porosity range 20–25%) comprising two synthetic and two natural (Berea and Corvio) samples, the latter used extensively as standards in rock physics research. We measured simultaneously ultrasonic (P- and S-wave) velocity and attenuation, electrical resistivity, permeability and axial and radial strains over a wide range of differential pressure (confining stress 15–50 MPa; pore pressure 5–10 MPa) on the four brine saturated samples. Despite some obvious physical discrepancies caused by the synthetic manufacturing process, such as silica cementation and anisotropy, the results show only small differences in stress dependency between the synthetic and natural sandstones for all measured parameters. Stress dependency analysis of the dry samples using an isotropic effective medium model of spheroidal pores and penny-shaped cracks, together with a granular cohesion model, provide evidence of crack closure mechanisms in the natural sandstones, seen to a much lesser extent in the synthetic sandstones. The smaller grain size, greater cement content, and cementation under oedometric conditions particularly affect the fluid transport properties of the synthetic sandstones, resulting in lower permeability and higher electrical resistivity for a similar porosity. The effective stress coefficients, determined for each parameter, are in agreement with data reported in the literature. Our results for the particular synthetic materials that were tested suggest that synthetic sandstones can serve as good proxies for natural sandstones for studies of elastic and mechanical properties, but should be used with care for transport properties studies.  相似文献   

5.
— The influence of differential stress on the permeability of a Lower Permian sandstone was investigated. Rock cylinders of 50 mm in diameter and 100 mm length of a fine-grained (mean grain size 0.2 mm), low-porosity (6–9%) sandstone were used to study the relation between differential stress, rock deformation, rock failure and hydraulic properties, with a focus on the changes of hydraulic properties in the pre-failure and failure region of triaxial rock deformation. The experiments were conducted at confining pressures up to 20 MPa, and axial force was controlled by lateral strain with a rate ranging from 10?6 to 10?7 sec?1. While deforming the samples, permeability was determined by steady-state technique with a pressure gradient of 1 MPa over the specimen length and a fluid pressure level between 40 and 90% of the confining pressure. The results show that permeability of low-porosity sandstones under increasing triaxial stress firstly decreases due to compaction and starts to increase after the onset of dilatancy. This kind of permeability evolution is similar to that of crystalline rocks. A significant dependence of permeability evolution on strain rate was found. Comparison of permeability to volumetric strain demonstrates that the permeability increase after the onset of dilatancy is not sufficient to regain the initial permeability up to failure of the specimen. The initial permeability, which was determined in advance of the experiments, usually was regained in the post-failure region. After the onset of dilatancy, the permeability increase displays a linear dependence on volumetric strain.  相似文献   

6.
The frequency dependent mechanism of local fluid flow was found to be the decisive absorption and dispersion mechanism in fluid containing sandstones. In the ultrasonic frequency range local fluid flow and grain surface effects control the behaviour of highly porous and highly permeable rock if a pore fluid is present. Both mechanisms depend less on macroscopic rock parameters like porosity and permeability than essentially on microscopic parameters like crack size, crack density and grain contact properties. To demonstrate directly the important influence of the microstructure on the rock elastic and anelastic properties the microstructure of a sandstone was artificially changed by thermal cracking. The cracked rock exhibits a clearly changed behaviour at low uniaxial as well as at high hydrostatic pressure despite small changes of porosity and permeability. Fluid effects increase due to cracking. The experimental results are explained by means of a rock, model and local fluid flow. These results emphasize that it is the microstructure which controls the elastic and anelastic rock behaviour, even at high hydrostatic pressure.  相似文献   

7.
The Rotliegend of the North German basin is the target reservoir of an interdisciplinary investigation program to develop a technology for the generation of geothermal electricity from low-enthalpy reservoirs. An in situ downhole laboratory was established in the 4.3 km deep well Groβ Schönebeck with the purpose of developing appropriate stimulation methods to increase permeability of deep aquifers by enhancing or creating secondary porosity and flow paths. The goal is to learn how to enhance the inflow performance of a well from a variety of rock types in low permeable geothermal reservoirs. A change in effective stress due to fluid pressure was observed to be one of the key parameters influencing flow properties both downhole and in laboratory experiments on reservoir rocks. Fluid pressure variation was induced using proppant-gel-frac techniques as well as waterfrac techniques in several different new experiments in the borehole. A pressure step test indicates generation and extension of multiple fractures with closure pressures between 6 and 8.4 MPa above formation pressure. In a 24-hour production test 859 m3 water was produced from depth indicating an increase of productivity in comparison with former tests. Different depth sections and transmissibility values were observed in the borehole depending on fluid pressure. In addition, laboratory experiments were performed on core samples from the sandstone reservoir under uniaxial strain conditions, i.e., no lateral strain, constant axial load. The experiments on the borehole and the laboratory scale were realized on the same rock types under comparable stress conditions with similar pore pressure variations. Nevertheless, stress dependences of permeability are not easy to compare from scale to scale. Laboratory investigations reflect permeability variations due to microstructural heterogeneities and the behavior in the borehole is dominated by the generation of connections to large-scale structural patterns.  相似文献   

8.
The influence of hydrostatic and uniaxial stress states on the porosity and permeability of sandstones has been investigated. The experimental procedure uses a special triaxial cell which allows permeability measurements in the axial and radial directions. The core sleeve is equipped with two pressure samplers placed distant from the ends. They provide mid-length axial permeability measure as opposed to the overall permeability measure, which is based on the flow imposed through the pistons of the triaxial cell. The core sleeve is also equipped to perform flows in two directions transverse to the axis of the sample. Two independent measures of axial and complementary radial permeability are thus obtained. Both Fontainebleau sandstone specimens with a porosity of about 5.8% to 8% and low permeability ranging from 2.5 mD to 30 mD and Bentheimer sandstone with a porosity of 24% and a high permeability of 3D have been tested. The initial axial permeability values obtained by each method are in good agreement for the Fontainebleau sandstone. The Bentheimer sandstone samples present an axial mid-length permeability 1.6 times higher than the overall permeability. A similar discrepancy is also observed in the radial direction, also it relates essentially to the shape of flow lines induced by the radial flow. All the tested samples have shown a higher stress dependency of overall and radial permeability than mid-length permeability. The effect of compaction damage at the pistons/sample and radial ports/sample interfaces is discussed. The relevance of directional permeability measurements during continuous uniaxial compression loadings has been shown on the Bentheimer sandstone until the failure of the sample. We can efficiently measure the influence of brittle failure associated to dilatant regime on the permeability: It tends to increase in the failure propagation direction and to decrease strongly in the transverse direction.  相似文献   

9.
A laboratory study was carried out to investigate the influence of confining stress on compressional- and shear-wave velocities for a set of rock samples from gas-producing sandstone reservoirs in the Cooper Basin, South Australia. The suite of samples consists of 22 consolidated sublitharenites with helium porosity ranging from 2.6% to 16.6%. We used a pulse-echo technique to measure compressional- and shear-wave velocities on dry samples (cylindrical 4.6 × 2 cm) at room temperature and at elevated confining stress (≤ 60 MPa). Compressional- and shear-wave velocities in samples increase non-linearly with confining stress. A regression equation of the form V = A ? Be?DP gives a good fit to the measured velocities with improved prediction of velocities at high confining stresses compared with equations suggested by other studies. The predicted microcrack-closure stresses of the samples show values ranging from 70 MPa to 95 MPa and insignificant correlation with porosity, permeability or clay content. There is a positive correlation between change in velocity with core porosity and permeability, but this association is weak and diminishes with increasing confining stress. Experimental results show that pore geometry, grain-contact type, and distribution and location of clay particles may be more significant than total porosity and clay content in describing the stress sensitivity of sandstones at in situ reservoir effective stress. The stress dependence of Cooper Basin sandstones is very large compared with data from other studies. The implication of our study for hydrocarbon exploration is that where the in situ reservoir effective stress is much less than the microcrack-closure stress of the reservoir rocks, the variation of reservoir effective stress could cause significant changes in velocity of the reservoir rocks. The velocity changes induced by effective stress in highly stress-sensitive rocks can be detected at sonic-log and probably surface-seismic frequencies.  相似文献   

10.
以鄂尔多斯盆地X地区长6储层为研究对象,利用多尺度CT成像技术、聚焦离子束扫描电镜技术,结合Avizo软件的强大数据处理和数值模拟功能,对研究区目的层岩石样品进行不同尺度孔喉分维数重构,建立三维超低渗透砂岩储层纳米级孔隙结构模型.研究表明,微米尺度下,超低渗透砂岩储层孔喉形态呈点状、球状和条带状及管状.储集空间类型以溶蚀微孔为主且多孤立分布,局部孔隙为片状,连通性较差.纳米尺度下,超低渗透砂岩储层孔喉系统整体较发育,孔喉形态呈球状、短管状.远离裂隙处多为孤立状,连通性较差,仅具有储集能力.微裂缝、粒间缝发育部位多为短管状,有一定连通性,相当于喉道.微观非均质性较强,岩样整体较致密,局部相互连通,溶蚀孔及裂隙对储集能力、渗滤能力具有控制作用.数值计算求得目的层A、Y、C三个样品的孔隙度分别为6.95%、5.55%、4.44%,渗透率分别为0.828×10^-3μm^2、0.115×10^-3μm^2、0.00065×10^-3μm^2.聚焦离子束扫描电镜与多尺度CT成像技术相结合能够定量表征超低渗透砂岩储层微、纳米级孔隙结构.  相似文献   

11.
We present a comprehensive characterisation of the physical, mineralogical, geomechanical, geophysical, and hydrodynamic properties of Corvio sandstone. This information, together with a detailed assessment of anisotropy, is needed to establish Corvio sandstone as a useful laboratory rock‐testing standard for well‐constrained studies of thermo–hydro–mechanical–chemical coupled phenomena associated with CO2 storage practices and for geological reservoir studies in general. More than 200 core plugs of Corvio sandstone (38.1 and 50 mm diameters, 2:1 length‐to‐diameter ratio) were used in this characterisation study, with a rock porosity of 21.7 ± 1.2%, dry density 2036 ± 32 kg m?3, and unconfined compressive and tensile strengths of 41 ± 3.28 and 2.3 ± 0.14 MPa, respectively. Geomechanical tests show that the rock behaves elastically between ～10 and ～18 MPa under unconfined conditions with associated Young's modulus and Poisson's ratio of 11.8 ± 2.8 GPa and 0.34 ± 0.01 GPa, respectively. Permeability abruptly decreases with confining pressure up to ～10 MPa and then stabilises at ～1 mD. Ultrasonic P‐ and S‐wave velocities vary from about 2.8–3.8 km s?1 and 1.5–2.4 km s?1, respectively, over confining and differential pressures between 0.1 and 35 MPa, allowing derivation of associated dynamic elastic moduli. Anisotropy was investigated using oriented core plugs for electrical resistivity, elastic wave velocity and attenuation, permeability, and tracer injection tests. Corvio sandstone shows weak transverse isotropy (symmetry axis normal to bedding) of <10% for velocity and <20% for attenuation.  相似文献   

12.
王伟  吕军  刘桃根  顾锦健  徐卫亚 《地震学刊》2013,(6):719-724,729
在TRIAXIAL CELL V3岩石三轴伺服试验机上进行了砂岩的渗透试验,采用流量法测量不同围压和渗透压作用下的砂岩渗透率,揭示了围压和渗透压对砂岩渗透率的影响规律,并给出了围压与渗透率的拟合关系式。结果表明,在相同围压下,随着渗透压差的增加,砂岩渗透率呈不同程度的增加;围压越小,渗透压差对渗透率的影响越大;当渗透压差相同时,砂岩围压一渗透率曲线变化趋势基本一致,渗透率随围压的增加而减小,显示砂岩内部裂隙的闭合程度受围压的影响较明显。  相似文献   

13.
As seismic data quality improves, time‐lapse seismic data is increasingly being called upon to interpret and predict changes during reservoir development and production. Since pressure change is a major component of reservoir change during production, a thorough understanding of the influence of pore pressure on seismic velocity is critical. Laboratory measurements show that differential pressure (overburden minus fluid pressure) does not adequately determine the actual reservoir conditions. Changes in fluid pressure are found to have an additional effect on the physical properties of rocks. The effective‐stress coefficient n is used to quantify the effect of pore pressure compared to confining pressure on rock properties. However, the current practice in time‐lapse feasibility studies, reservoir‐pressure inversion and pore‐pressure prediction is to assume that n= 1. Laboratory measurements, reported in both this and previous research show that n can be significantly less than unity for low‐porosity rocks and that it varies with porosity, rock texture and wave type. We report the results of ultrasonic experiments to estimate n for low‐porosity sandstones with and without microcracks. Our results show that, for P‐waves, n is as low as 0.4 at a differential pressure of 20 MPa (about 3000 psi) for a low‐porosity sandstone. Thus, in pore‐pressure inversion, an assumption of n= 1 would lead to a 150% underestimation of the pore pressure. Comparison of the effective‐stress coefficient for fractured and unfractured samples suggests that the presence of microfractures increases the sensitivity of P‐wave velocity to pore pressure, and therefore the effective‐stress coefficient. Our results show that the effective‐stress coefficient decreases with the differential pressure, with a higher differential pressure resulting in a lower effective‐stress coefficient. While the effective‐stress coefficient for P‐wave velocity can be significantly less than unity, it is close to one for S‐waves.  相似文献   

14.
High‐resolution three‐dimensional images are used in digital rock physics to numerically compute rock physical properties such as permeability and elastic moduli. These images are not widely available, and their preparation is both expensive and time consuming. All of these issues highlight the importance of alternative digital rock physics methods that are based on two‐dimensional images and use different approaches to compute effective properties of three‐dimensional samples. In addition, the scale of study in both standard and alternative digital rock physics is very small, which applications of its results are questionable at wells or reservoir scale. The aim of this study is to use two‐dimensional images and alternative digital rock physics techniques for computing seismic wave velocity and permeability, which are compared with well and laboratory data. For this purpose, data from one well in a reservoir located in the southwestern part of Iran are used. First, two clean (carbonate) and two cemented (limy sandstone) samples were collected from well cores at different depths. Then, two‐dimensional images by scanning electron microscope and conventional microscope were captured. In the next step, two alternative digital rock physics methods, namely, empirical relations and conditional reconstruction, have been employed to compute P‐wave velocity and permeability of a three‐dimensional medium. Results showed that, in clean (mono‐mineral) samples, velocity values were reasonably close to well data. However, permeability values are underestimated compared with laboratory data because laboratory data were obtained at ambient pressure, whereas alternative digital rock physics results are more representative of reservoir pressure conditions. Nevertheless, permeability–porosity trends are valid for both samples. In the case of cemented samples, a two‐scale procedure, along with a method for two‐scale computation and grain‐cement segmentation, is presented and developed. Results showed that P‐wave velocity is overestimated probably due to random sampling in this method. However, velocity–porosity trends are in agreement with well data. Moreover, permeability results obtained for cemented samples were also similar to those obtained for the clean samples.  相似文献   

15.
We present a formulation for mechanical modeling of the interaction between fracture and fluid flow. Our model combines the classic Biot poroelastic theory and a damage rheology model. The model provides an internally consistent framework for simulating coupled evolution of fractures and fluid flow together with gradual transition from brittle fracture to cataclastic flow in high-porosity rocks. The theoretical analysis, based on thermodynamic principles, leads to a system of coupled kinetic equations for the evolution of damage and porosity. A significant advantage of the model is the ability to reproduce the entire yield curve, including positive and negative slopes, in high-porosity rocks by a unified formulation. A transition from positive to negative values in the yield curve, referred to as a yield cap, is determined by the competition between the two thermodynamic forces associated with damage and porosity evolution. Numerical simulations of triaxial compression tests reproduce the gradual transition from localized brittle failure to distributed cataclastic flow with increasing pressure in high-porosity rocks and fit well experimentally measured yield stress for Berea sandstone samples. We modified a widely used permeability porosity relation by accounting for the effect of damage intensity on the connectivity. The new damage-permeability relation, together with the coupled kinetics of damage and porosity evolution, reproduces a wide range of realistic features of rock behavior. We constrain the model variables by comparisons of the theoretical predictions with laboratory results reporting porosity and permeability variation in rock samples during isotropic and anisotropic loading. The new damage-porosity-permeability relation enables simulation of coupled evolution of fractures and fluid flow and provides a possible explanation for permeability measurements in high-porosity rocks, referred to as the “apparent permeability paradox.” The text was submitted by the authors in English.  相似文献   

16.
— The mechanical behaviour of Bentheim sandstone, a homogeneous quartz-rich sandstone with porosity of 22.8%, was investigated by triaxial compression tests conducted on dry samples. At confining pressures up to 35 MPa, the failure mode was characterized by a typical brittle deformation regime, as the samples showed dilatancy and failed by strain softening and brittle faulting. Previous studies have shown that the mechanical behaviour and failure mode of brittle porous granular rocks are governed by the time-dependent growth of microcracks. We analyse this process using the “Pore Crack Model” based on fracture mechanics analysis. It is consistent with the microstructure of porous granular rocks since it considers the growth of axial cracks from cylindrical holes in two dimensions. These cracks grow when their stress intensity factors reach the subcritical crack growth limit. Interaction between neighbouring cracks is introduced by calculating the stress intensity factor as the sum of two terms: a component for an isolated crack and an interaction term computed using the method of successive approximations. It depends on crack length, pore radius, pore density, and applied stresses. The simulation of crack growth from cylindrical holes, associated with a failure criterion based on the coalescence of interacting cracks, is used to compare the theoretical stress at the onset of dilatancy and at macroscopic rupture to the experimental determined values. Our approach gives theoretical results in good agreement with experimental data when microstructural parameters consistent with observations are introduced.  相似文献   

17.
Rock brittleness directly affects reservoir fracturing and its evaluation is essential for establishing fracturing conditions prior to reservoir reforming. Dynamic and static brittleness data were collected from siltstones of the Qingshankou Formation in Songliao Basin. The brittle–plastic transition was investigated based on the stress–strain relation. The results suggest that the brittleness indices calculated by static elastic parameters are negatively correlated with the stress drop coefficient and the brittleness index B2, defined as the average of the normalized Young’s modulus and Poisson’s ratio, is strongly correlated with the stress drop. The brittleness index B2, Young’s modulus, and Poisson’s ratio correlate with the brittle minerals content; that is, quartz, carbonates, and pyrite. We also investigated the correlation between pore fluid and porosity and dynamic brittle characteristic based on index B2. Pore fluid increases the plasticity of rock and reduces brittleness; moreover, with increasing porosity, rock brittleness decreases. The gas-saturated siltstone brittleness index is higher than that in oil- or water-saturated siltstone; the difference in the brittleness indices of oil- and water-saturated siltstone is very small. By comparing the rock mechanics and ultrasonic experiments, we find that the brittleness index obtained from the rock mechanics experiments is smaller than that obtained from the ultrasonic experiments; nevertheless, both decrease with increasing porosity as well as their differences. Ultrasonic waves propagate through the rock specimens without affecting them, whereas rock mechanics experiments are destructive and induce microcracking and porosity increases; consequently, the brittleness of low-porosity rocks is affected by the formation of internal microcrack systems.  相似文献   

18.
为了解决煤储层物性的预测方法问题,本文基于大量的文献调研,梳理了煤储层孔隙性和渗透性的影响因素和预测方法,并进行了预测技术展望.研究表明,孔隙性影响因素主要有煤层埋深、压实作用、变质程度和显微组分等,孔隙度预测方法主要有双侧向迭代法、阿尔奇公式裂缝孔隙度估算法、双侧向数值模拟法、相关分析方法及支持向量机等方法;渗透性影响因素主要有煤层埋深、储层压力、煤的变质程度、煤体结构、煤岩组分、应力状态、基质收缩作用和裂隙系统发育程度等,渗透性预测方法主要有F-S计算方法、基于达西定律的计算方法、相关分析法及多层次模糊综合评判法等其他方法.本文认为遵循“地质约束测井、岩心刻度测井”的原则,加强煤层气储层岩石物理研究和物性影响因素分析是基础;常规测井信息与测井新技术信息结合,“多尺度信息融合”建立煤岩孔隙度和渗透率解释新模型,充分发挥多种非线性数学方法的优势构建煤岩物性非线性数学预测方法有一定的实际意义.  相似文献   

19.
Analytical models are provided that describe how the elastic compliance, electrical conductivity, and fluid‐flow permeability of rocks depend on stress and fluid pressure. In order to explain published laboratory data on how seismic velocities and electrical conductivity vary in sandstones and granites, the models require a population of cracks to be present in a possibly porous host phase. The central objective is to obtain a consistent mean‐field analytical model that shows how each modeled rock property depends on the nature of the crack population. The crack populations are described by a crack density, a probability distribution for the crack apertures and radii, and the averaged orientation of the cracks. The possibly anisotropic nature of the elasticity, conductivity, and permeability tensors is allowed for; however, only the isotropic limit is used when comparing to laboratory data. For the transport properties of conductivity and permeability, the percolation effect of the crack population linking up to form a connected path across a sample is modeled. However, this effect is important only in crystalline rock where the host phase has very small conductivity and permeability. In general, the importance of the crack population to the transport properties increases as the host phase becomes less conductive and less permeable.  相似文献   

20.
Seismoelectric coupling coefficients are difficult to predict theoretically because they depend on a large numbers of rock properties, including porosity, permeability, tortuosity, etc. The dependence of the coupling coefficient on rock properties such as permeability requires experimental data. In this study, we carry out a set of laboratory measurements to determine the dependence of seismoelectric coupling coefficient on permeability. We use both an artificial porous “sandstone” sample, with cracks, built using quartz‐sand and Berea sandstone samples. The artificial sample is a cube with 39% porosity. Its permeability levels are anisotropic: 14.7 D, 13.8 D, and 8.3 D in the x‐, y‐, and z‐directions, respectively. Seismoelectric measurements are performed in a water tank in the frequency range of 20 kHz–90 kHz. A piezoelectric P‐wave source is used to generate an acoustic wave that propagates through the sample from the three different (x, y, and z) directions. The amplitudes of the seismoelectric signal induced by the acoustic waves vary with the direction. The highest signal is in the direction of the highest permeability, and the lowest signal is in the direction of the lowest permeability. Since the porosity of the sample is constant, the results directly show the dependence of seismoelectric coefficients on permeability. Seismoelectric measurements with natural rocks are performed using Berea sandstone 500 and 100 samples. Because the Berea samples are nearly isotropic in permeability, the amplitudes of the seismoelectric signals induced in the different directions are the same within the measurement error. Because the permeability of Berea 500 is higher than that of Berea 100, the amplitude of the seismoelectric signals induced in Berea 500 is higher than those in Berea 100. To determine the relative contributions of porosity and permeability on seismoelectric conversion, we carried out an analysis, using Pride (1994) formulation and Kozeny–Carman relationship; the normalized amplitudes of seismoelectric coupling coefficients in three directions are calculated and compared with the experimental results. The results show that the seismoelectric conversion is related to permeability in the frequency range of measurements. This is an encouraging result since it opens the possibility of determining the permeability of a formation from seismoelectric measurements.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号