共查询到20条相似文献，搜索用时 46 毫秒
1.
Three-dimensional surface crack initiation and propagation in two kinds of heterogeneous rocks were numerically investigated via parallel finite element analysis using a supercomputer. Numerically simulated rock specimens containing a pre-existing flaw were subjected to uniaxial compression until failure. The initiation and propagation of wing cracks, anti-wing cracks, and shell-like cracks were reproduced by numerical simulations. The numerically simulated results demonstrate that the further propagation of wing cracks and shell-like cracks stop due to their wrapping (curving) behavior in three-dimensional spaces, even if the applied loads continue to increase. Furthermore, rock heterogeneity could significantly influence crack propagation patterns and the peak uniaxial compressive strengths of rock specimens. Moreover, anti-wing cracks only appeared in relatively heterogeneous rocks, and the peak uniaxial compressive strengths of the specimens were observed to depend on the inclination of the pre-existing flaw. Finally, the mechanism of surface crack propagation is discussed in the context of numerically simulated anti-plane loading tests, wherein it was identified that Mode III loading (anti-plane loading) does not lead to Mode III fracture in rocks due to their high ratio of uniaxial compressive strength to tensile strength. This finding could explain the lateral growth of an existing flaw in its own plane, which is a phenomenon that has not been observed in laboratory experiments. 相似文献
2.
The phase field model represents sharp cracks by diffusive mushy-zone and can simulate crack propagation automatically. Propagation and coalescence of quasi-static cracks in Brazilian disks are investigated by a phase field model. The phase field modeling is implemented in Comsol Multiphysics and initially verified by a benchmark of three-point bending test. The Brazilian disk specimens containing no initial crack, a single and two pre-existing cracks subjected to compression are then tested by the phase field model. Crack propagation patterns along with the load–displacement curves are fully discussed. Meanwhile, the effects of length scale parameter and critical energy release rate on crack propagation are evaluated. In addition, the effect of crack inclination angle on the pre-cracked Brazilian disk specimens is also investigated. The numerical results obtained by the phase field model are in good agreement with previous experimental and numerical results.
相似文献3.
为研究不同孔洞-裂隙（简称"孔-隙"）赋存条件下的裂纹扩展规律,利用RFPA软件,对不同裂纹倾角及不同非均质系数下的岩体破坏进行数值模拟分析,获得其裂纹扩展过程、声发射规律、应力-应变曲线,同时与原试验结果进行对比验证。结果表明:完整试样裂纹沿着剪切方向产生,含孔-隙试样裂纹沿裂隙尖端及孔口侧边产生;翼裂纹贯穿试件的同时,在预制裂纹尖端或孔口侧边产生水平方向的次生裂纹,并产生分叉,非均质系数影响次生裂纹走向;压载前期试样以拉破坏为主,压载后期以拉-剪组合破坏为主,次生裂纹的产生与剪切破坏有关;声发射累计能量与声发射累计数前期缓慢增大,后期迅速增大,预制裂纹倾角越小,非均质系数越大,声发射累计能量越大;不同裂纹倾角及不同非均质系数试件的应力-应变曲线均经历3个阶段:弹性变形阶段、非线性变形阶段及残余变形阶段,孔-隙的存在降低了试样的峰值强度,影响试件的脆性度。研究结果为进一步认识孔-隙相互作用规律提供了参考。 相似文献
4.
Summary ?Cracks that initiate from pre-existing discontinuities can link with other cracks or with other discontinuities and produce
failure in a rock mass. The Displacement Discontinuity Method (DDM), FROCK, is used in this investigation to model experimental
observations on pre-cracked specimens of gypsum. In these experiments two fractures, which were either both open or closed,
were placed through the thickness of the specimens, and detailed observations of the cracking process were performed as the
specimens were loaded in uniaxial compression. The following aspects are studied for both open and closed fractures: 1) crack
initiation stress; 2) direction and propagation of the new cracks; 3) type of coalescence and stress at which it occurs. Modeling
is done considering the actual size of the specimens. Relations between the direction of initiation for each type of crack,
the orientation of the initial fractures, and the type and coalescence are established. In addition, comparisons between results
from experiments and predictions from the model are presented. The numerical results are in agreement with the experiments. 相似文献
5.
脆性岩石材料在压应力作用下常出现两类裂纹：翼型张拉裂纹和次生剪切裂纹。近场动力学是一种新型的无网格数值计算方法。在近场动力学理论中,采用积分形式的控制方程代替微分形式的控制方程使得该数值算法在断裂问题上具有独特的优势。将Mohr-Coulomb准则和最大主应力准则引入非普通“态”基近场动力学理论中,分别用于模拟材料常见的压剪和张拉破坏。这种扩展的非普通“态”基近场动力学可以有效地模拟脆性岩石材料在多种受力状态下的裂纹起裂、扩展和连接问题。通过5个不同的数值算例说明该数值算法在处理脆性岩石材料断裂问题的有效性和准确性。首先,通过模拟含圆孔的弹性板拉伸数值试验说明该数值算法的有效性和准确性。其次,数值模拟了简单三点弯曲试验以及不使用其他外部准则条件下动荷载作用下裂纹的分叉试验,所得结果与其他试验结果或数值结果相吻合,从而验证了该理论的有效性。然后,模拟了包含斜裂纹的巴西圆盘试验,裂纹扩展路径和计算所得的断裂韧度同样吻合于试验结果。最后,模拟了单轴压缩状态下,预制裂纹试样的裂纹扩展和连接问题。将该数值算法与试验结果对比表明,所提出的数值方法可以模拟和预测岩石类材料的张拉和压剪裂纹的起裂、扩展和连接行为。 相似文献
6.
单轴压缩下含倾斜单裂纹砂岩试件裂纹扩展量测研究 总被引：3，自引：0，他引：3
选用砂岩作为试验材料,进行不同倾斜角度单预制裂纹的单轴压缩试验研究,透过裂纹扩展量测技术以及配合相关断裂准则,得到：(1) 理论与实验的裂纹起裂角随裂纹倾斜角增加而增大;(2) 透过相关断裂准则,砂岩试件在裂纹尖端产生反翼裂纹是因为剪力破坏;(3) 在单轴压缩作用下砂岩试件裂纹扩展受单裂纹的倾斜角影响,当裂纹倾斜角较小时,裂纹不易起裂;当裂纹倾斜角较大时,裂纹起裂比较容易;(4) 在单轴压缩作用下砂岩试件则受单预制裂纹的倾斜角影响,当裂纹倾斜角较小时,裂纹扩展属于非稳定扩展;当裂纹倾斜角较大时,裂纹扩展属于稳定扩展;(5) 在单轴压缩作用下砂岩试件裂纹尖端A侧与裂纹尖端 B侧的裂纹扩展平均速度随裂纹倾斜角增加而降低。 相似文献
7.
运用三维数值流形法（3D NMM）进行三维裂纹扩展分析,并采用C++语言编写了相应的程序。充分利用三维数值流形法模拟裂纹扩展的优势,只需要更新裂纹尖端线附近的边界环路和流形单元,不需要使用阶跃函数。根据三维数值流形法计算得到的应力结果,应用非局部求迹方法分析每个裂纹尖端的破坏状态,如果发生破坏则沿垂直于其最大主应力方向扩展。针对裂纹扩展后的不同状况,采用四边形或三角形推进法。裂纹扩展后为了使变形后的面保持平面,必须对新生成的面进行三角化分割。对诸如单边裂纹、平行钱币型裂纹和倾斜钱币型裂纹扩展问题进行数值模拟。计算结果表明,采用三维数值流形法进行裂纹扩展模拟是可行的,文中方法对裂纹尖端线非闭合和闭合的情形均适用,且文中方法对于裂纹尖端线位于单元内部的非平面裂纹扩展也是有效的。 相似文献
8.
Mahmoud Behnia Kamran Goshtasbi Mohammad Fatehi Marji Aliakbar Golshani 《Arabian Journal of Geosciences》2014,7(7):2729-2737
In the present study, a boundary element method based on the higher order displacement discontinuity formulation is presented to solve the general problem of hydraulic fracture propagation in layered formations. Displacement collocation technique is employed to model the higher order displacement variation along the crack and the special crack tip element near its ends. The hydraulic fracture propagation and its interaction with the layer interface in non-homogenous rock materials are studied by the proposed semi-analytical (hybridized boundary element-boundary collocation) method. The maximum tangential stress criterion (or σ-criterion) of fracture mechanics considering different elastic constants (Young modulus and Poisson’s ratio) is used to obtain the fracture path. The fracture propagation from stiff to soft and soft to stiff media for cracks having different inclination angles is modeled, and the effects of elastic constants on the hydraulic fracture propagation is studied. The results show that if the hydraulic fracture originates in the stiffer layer, its capability to cross the layer increases and is vice versa for the softer material. The comparison of the results gained from the numerical method with those in the literature show a good performance of the method in the case of propagation of hydraulic fracture in layered formations. 相似文献
9.
Hydraulic fracturing is the method of choice to enhance reservoir permeability and well efficiency for extraction of shale gas. Multi‐stranded non‐planar hydraulic fractures are often observed in stimulation sites. Non‐planar fractures propagating from wellbores inclined from the direction of maximum horizontal stress have also been reported. The pressure required to propagate non‐planar fractures is in general higher than in the case of planar fractures. Current computational methods for the simulation of hydraulic fractures generally assume single, symmetric, and planar crack geometries. In order to better understand hydraulic fracturing in complex‐layered naturally fractured reservoirs, fully 3D models need to be developed. In this paper, we present simulations of 3D non‐planar fracture propagation using an adaptive generalized FEM. This method greatly facilitates the discretization of complex 3D fractures, as finite element faces are not required to fit the crack surfaces. A solution strategy for fully automatic propagation of arbitrary 3D cracks is presented. The fracture surface on which pressure is applied is also automatically updated at each step. An efficient technique to numerically integrate boundary conditions on crack surfaces is also proposed and implemented. Strongly graded localized refinement and analytical asymptotic expansions are used as enrichment functions in the neighborhood of fracture fronts to increase the computational accuracy and efficiency of the method. Stress intensity factors with pressure on crack faces are extracted using the contour integral method. Various non‐planar crack geometries are investigated to demonstrate the robustness and flexibility of the proposed simulation methodology. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
三叉裂隙是自然界普遍存在的一种岩体缺陷形式,其对岩体的力学特性有重要影响。对含预制三叉裂隙的水泥砂浆试样进行室内单轴压缩试验,配合使用摄像机拍摄裂纹的起裂、扩展、贯通过程,通过数字图像技术处理获取试样的应变场云图,并结合PFC2D程序研究不同?、? 条件下试样的强度特征、裂纹模式和裂纹演化扩展规律。研究表明：三叉裂隙对试样单轴抗压强度有明显的削弱作用。当? 恒定为120°时,试样在? = 30°时达到最大抗压强度;当? 恒定为90°时,随?增大,试样抗压强度呈先减小后增大的趋势,且当? = 45°时达到最大抗压强度。试样产生的裂纹可分为3类,分别是张拉型裂纹(Ⅰ型裂纹)、剪切型裂纹(Ⅱ型裂纹)、混合型裂纹(Ⅲ型裂纹)。这3类裂纹通常从裂隙尖端开始产生,并且Ⅰ型裂纹沿加载方向扩展,通常未扩展至试样边界;Ⅱ型和Ⅲ型裂纹通常与加载方向呈一定角度扩展至试样边界。通过对裂纹的几何形态和组成宏观裂纹的微裂纹成分的分析,得知导致含三叉裂隙试样在单轴压缩条件下失效的是张拉破坏。数字图像技术得到的应变云图表明,当载荷达到一定阶段,裂隙尖端出现应力集中,微破裂开始发育并聚集成微破裂区,微破裂区扩大产生宏观裂纹。通过对主应变和剪应变云图分析,发现导致试样失效的是张拉破坏,剪应变在裂纹扩展过程中的影响较小。 相似文献
11.
冲击载荷作用下准脆性材料Ⅱ型裂纹扩展研究 总被引：1，自引：0，他引：1
冲击载荷作用下准脆性材料的动态断裂一直是关注的热点问题,Ⅱ型裂纹试样受冲击剪切时其裂纹扩展方向同材料力学性质和冲击速度等密切相关。应用岩石动态破裂过程动态分析系统软件,对单边平行双裂缝试样开展了冲击载荷作用下的裂纹动态扩展数值模拟,分别研究了不同材料力学性质、材料均质度、入射应力脉冲幅值和历时对II型裂纹动态扩展的影响。数值模拟结果表明,纯II型裂纹在动荷载作用下的扩展,不仅受到剪切损伤,而且还存在拉伸损伤;准脆性材料的非均匀性导致了主裂缝周围产生大量微裂纹的破坏,影响裂缝的分岔和内部的应力值;应力幅值和应力脉冲历时分别超过某一定值时,主裂缝将出现分叉现象,试样的破坏程度加剧,其研究结果对于深入揭示准脆性材料在动荷载作用下II型裂纹扩展的规律及准脆性材料的损伤断裂机制具有重要的参考价值。 相似文献
12.
Evolution of Rock Cracks Under Unloading Condition 总被引：2，自引：0，他引：2
Underground excavation normally causes instability of the mother rock due to the release and redistribution of stress within the affected zone. For gaining deep insight into the characteristics and mechanism of rock crack evolution during underground excavation, laboratory tests are carried out on 36 man-made rock specimens with single or double cracks under two different unloading conditions. The results show that the strength of rock and the evolution of cracks are clearly influenced by both the inclination angle of individual cracks with reference to the unloading direction and the combination geometry of cracks. The peak strength of rock with a single crack becomes smaller with the inclination angle. Crack propagation progresses intermittently, as evidenced by a sudden increase in deformation and repeated fluctuation of measured stress. The rock with a single crack is found to fail in three modes, i.e., shear, tension–shear, and splitting, while the rock bridge between two cracks is normally failed in shear, tension–shear, and tension. The failure mode in which a crack rock or rock bridge behaves is found to be determined by the inclination angle of the original crack, initial stress state, and unloading condition. Another observation is that the secondary cracks are relatively easily created under high initial stress and quick unloading. 相似文献
13.
岩体内部赋存的裂隙很多表现为折线型,为探究这类岩体的断裂机制,制备含折线型裂隙砂岩试件并对其进行单轴压缩试验。采用数字图像相关(DIC)方法计算加载过程中的变形场演化,根据新生裂纹两侧的位移差异识别裂纹类型;运用扩展有限元法(XFEM)模拟断裂过程,根据应力分布特征解释翼型裂纹起裂与扩展机制。DIC计算结果表明,新生裂纹处出现应变局部化带,裂纹两侧发生相对分离;含直线型和折线型裂隙砂岩试件的翼型裂纹分别萌生于预制裂隙端部以及折角处,这是因为裂隙几何形态会改变拉应力集中位置;含折线型裂隙砂岩试件的起裂应力小于含直线型裂隙砂岩试件,这是因为相同加载条件下前者的最大拉应力值更大;这2类试件的裂纹扩展均是由于裂纹尖端集中的拉应力引起的,裂纹依然呈张开状态;裂隙几何形态未改变试件的最终破坏模式,均表现为对角剪切破坏。 相似文献
14.
Mixed-Mode Fracturing of Rocks Under Static and Cyclic Loading 总被引：1，自引：1，他引：0
Static diametrical compression tests conducted on inclined cracked chevron notched Brazilian disc (CCNBD) Brisbane tuff specimens showed that the notched cracks at the centre of the specimens opened (Mode I) up to 30° crack inclination angle (β), whereas crack closure (Mode II) started for β > 33°, and closure became more pronounced at even higher β of 45° and 70°. Both the experimental and numerical results showed that the crack initiation angle (θ) was a function of the β. Scanning electron microscope (SEM) images showed that fatigue damage on cyclic loading of Brisbane tuff is strongly influenced by the failure of the matrix due to both intergranular and transgranular fracturing. 相似文献
15.
接触裂纹问题在工程结构中较为常见。结合数值流形法在裂纹处理上的优势,分析了压剪荷载作用下的接触裂纹问题,模拟了压剪裂纹渐进扩展过程。为了减少由于裂纹尖端位置不同而产生的误差,对裂纹尖端附近一定范围内的每一个物理覆盖附加奇异覆盖函数项,并根据裂纹尖端位置和单元含奇异物理覆盖的数目进行分区积分。选取一个压剪破坏算例,分析了法向接触力对应力强度因子计算结果的影响,并模拟了其渐进破坏过程。计算结果表明,所提方法在压剪裂纹问题方面的可行性,与未细化和覆盖细化方法得到的结果相比,更能准确地描述裂纹扩展路径。法向接触力对II型应力强度因子的贡献为0,对I型应力强度因子的影响较大,相对误差随网格密度变化明显,且法向接触力对I型应力强度因子的影响要比直接施加内压时的影响大。 相似文献
16.
锦屏二级水电站深埋隧洞大量岩爆案例表明板裂化围岩的失稳破坏与岩爆之间具有很强的相关性。采用高强石膏配制满足板裂化围岩结构特征的硬脆性模型试样,通过一侧约束条件下的单轴压缩试验研究板裂化模型试样的失稳破坏过程、强度与变形特性及其裂纹扩展特征。研究表明,（1）板裂化模型试样失稳破坏过程表现出应变型岩爆的特征,其典型的破坏过程为预制裂隙尖端张拉裂纹的萌生与扩展-试样劈裂成板-岩板屈曲变形-岩板压折、岩片弹射;（2）与完整试样相比,含1条、2条、3条预制裂隙模型试样的峰值强度、弹性模量均呈现稳定下降的趋势,而峰值轴向应变则是先减小后增大;（3）试样预制裂隙尖端张拉裂纹的产生会造成：相邻预制裂隙尖端横向应变值的突变、试样侧向变形量的突增以及侧向变形速率的显著增大;（4）临空面附近的预制裂隙,其尖端产生的张拉裂纹在很短的时间内便会失稳扩展,并造成试样的失稳破坏。最后,分析试样变形破坏过程中的声发射特性。研究结果对于揭示深埋硬岩隧洞板裂化围岩的失稳破坏规律、岩爆的发生机制具有重要意义。 相似文献
17.
18.
断裂力学是各行业的基础学科之一。半圆弯拉(SCB)试验为该领域经典试验,目前含裂纹的SCB研究多为底部切口等表面裂纹或穿透型裂纹研究。内裂纹和内部类裂纹缺陷是材料的固有属性,但是对于SCB内裂纹扩展规律研究较少。基于3D-ILC（三维激光疲劳内裂纹）技术,分析了表面无任何影响的情况下凭空生成任意参数的纯内裂纹,在SCB试样中生成内裂纹,对含内裂纹试样进行SCB试验,分析了裂纹生长过程、应力双折射规律、I-II-III型裂纹扩展面、破坏形态、宏微观断口特征,开展数值模拟,得到裂纹尖端应力强度因子分布规律及扩展路径,与物理试验一致。结果表明：（1）基于3D-ILC的SCB内裂纹及I-II-III型扩展断裂规律明显,3D-ILC为断裂力学中的内裂纹问题研究提供了有力工具;（2）应力云纹在内裂纹处显示应力集中,SCB整体云纹在内裂纹处发生明显变异;（3）SCB试样从预制裂纹处发生压剪型起裂,发生I-II-III型裂纹扩展,分为光滑区和撕裂区,持续生长转变为动态断裂进而破坏,动态断口存在裂纹分叉出现雾化区、羽毛区特征;（4）根据M积分和最大周向应力准则,对试样进行了数值模拟,得到了试样内裂纹尖端应力强度因子分布规律及扩展路径,与试验结果一致。结论与成果对断裂力学领域的SCB试验、内裂纹、I-II-III型断裂问题、裂纹扩展路径模拟问题的研究,具有重要意义。 相似文献
19.
Cracking and coalescence behavior in a rectangular rock-like specimen containing two parallel (stepped and coplanar) pre-existing open flaws under uniaxial compression load has been numerically studied by a parallel bonded-particle model, which is a type of bonded-particle model. Crack initiation and propagation from two flaws replicate most of the phenomena observed in prior physical experiments, such as the type (tensile/shear) and the initiation stress of the first crack, as well as the coalescence pattern. Eight crack coalescence categories representing different crack types and trajectories are identified. New coalescence categories namely “New 1” and “New 2”, which are first observed in the present simulation, are incorporated into categories 3 and 4, and category 5 previously proposed by the MIT Rock Mechanics Research Group, respectively. The flaw inclination angle (β), the ligament length (L) (spacing between two flaws) and the bridging angle (α) (inclination of a line linking up the inner flaw tips, between two flaws) have different effects on the coalescence patterns, coalescence stresses (before, at or post the peak stress) as well as peak strength of specimens. Some insights on the coalescence processes, such as the initiation of cracks in the intact part of specimens at a distance away from the flaw tips, and coalescence due to the development and linkage of a number of steeply inclined to vertical macro-tensile cracks are revealed by the present numerical study. 相似文献
20.
利用颗粒流程序（PFC) 对直切槽式圆盘试样进行巴西试验模拟,分析了不同的裂隙倾角和裂隙长度对直切槽式圆盘试样裂纹扩展规律的影响。根据起裂位置的不同,主裂纹可分为从裂隙尖端萌生的Ⅰ型主裂纹和从裂隙尖端一定距离处萌生的Ⅱ型主裂纹;次生裂纹可分为从加载点附近萌生的Ⅰ型次生裂纹和从远离加载点的一侧萌生的Ⅱ型次生裂纹。当裂隙长度保持不变而增大裂隙倾角时,主裂纹从Ⅰ型过渡为Ⅱ型,次生裂纹则从Ⅰ型转变为Ⅰ型和Ⅱ型共存,最后又变为Ⅰ型。当裂隙角度保持不变而增大裂隙长度时,主裂纹保持不变,次生裂纹则由Ⅰ型逐渐过渡为Ⅰ型和Ⅱ型共存。另外,当径向应力达到峰值应力之后,试样内会有大量的微裂纹萌生、扩展,造成了圆盘试样的破坏。从力链和能量角度来看,巴西圆盘试样的破裂过程是试样内部拉应力集中产生的颗粒间黏结破裂以及应变能释放的过程。 相似文献