共查询到20条相似文献，搜索用时 31 毫秒
1.
节理岩体锚杆的综合变形分析 总被引：2，自引：0，他引：2
在总结国内外对节理岩体中锚杆加固机制的试验研究和理论探讨基础上,综合考虑锚杆的切向和轴向变形能力,建立节理锚固锚杆在剪切荷载作用下的变形模型,将节理锚固锚杆的变形区划分为弹性变形段和挤压破坏段,引入表征挤压破坏段长度的变量,对锚杆与岩体的相互作用机制进行理论分析,推导了剪切荷载与剪切位移和轴向荷载与轴向位移的关系。通过分析锚杆的屈服破坏形式,得到了确定挤压破坏段长度的方法。最后,通过算例分析了挤压破坏段长度与锚杆直径、岩体强度、锚固角度等参数的关系,得到了以下结论：（1）节理锚固锚杆抗剪作用的实质是锚杆调动岩体的抗压强度抵抗节理切向荷载。在抗压强度较高的硬岩中,挤压破坏段局限于节理面附近,锚杆影响范围小;而在抗压强度较低的软岩中,挤压破坏段较大,而且会产生较大的剪切变形,锚杆影响范围较大。（2）锚杆屈服破坏形式与岩质和锚杆直径有关。硬质岩体发生剪切屈服,而较软岩体中容易发生弯曲屈服;小直径锚杆一般直接剪切屈服,而大直径锚杆可能发生弯曲屈服。锚杆屈服破坏后出现塑性铰,挤压破坏段范围在节理一侧约为直径的1～2倍,继续增加剪切荷载,挤压破坏段长度不再增大。（3）随岩质的不同,锚杆锚固节理的最优锚固角变化较大。岩质较硬时,最优锚固角度较小,反之则较大。 相似文献
2.
The load transfer capacity and failure mechanism of a fully grouted bolt installed across a joint in shear is investigated,
both experimentally and numerically, in five types of bolt. The double-shearing testing of bolts were studied in concrete
blocks of 20, 40 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN, respectively.
The parameters examined include: shear resistance, shear displacement, induced strains and stresses during the bolt-bending
process, and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were that the strength
of the concrete, bolt profile configuration and bolt pretension load played a significant influence on the shear resistance,
shear displacement and failure mechanism of the reinforced medium. Experimental and numerical simulations showed that the
failure occurs as a result of the induced axial and shear stresses acting between the hinge point distances in the vicinity
of the shear joint plane. 相似文献
3.
This study aims to provide knowledge on the thermo-mechanical behaviour of heat exchanger piles, through a laboratory scale model. The model pile (20 mm in external diameter) was embedded in dry sand. The behaviour of the axially loaded pile under thermal cycles was investigated. After applying the axial load on the pile head, the pile temperature was varied between 5 and 30 °C. Seven tests, corresponding to various axial loads ranging from 0 to 70 % of the pile estimated bearing capacity, were performed. The results on pile head displacement show that heating under low axial load induced heave and cooling induced settlement; the pile temperature-displacement curve was found to be reversible and compatible with the thermal expansion curve of the pile. However, at higher axial loads, irreversible settlement of the pile head was observed after a few thermal cycles. The axial load profile measured by the strain gauges evidenced that the pile head load was mainly transferred to the pile toe. Nevertheless, thermal cycles modified significantly the mobilised skin friction along the pile. The total pressure measured at various locations in the soil mass was also slightly influenced by the thermal cycles. 相似文献
4.
基于锚固界面的一种非线性剪切滑移模型,采用荷载传递方法分析了锚固长度对锚杆受力特性的影响,建立了锚杆临界锚固长度的计算方法,并通过工程案例检验其可行性。结果表明：锚固长度较小时,锚杆荷载-位移曲线为承载力较小的单峰曲线;随着锚固长度的增加,逐渐衍生出一个平缓变化区段;锚固长度越小,界面剪应力分布越均匀,但整体承载力也越小;随着锚固长度增加,界面剪应力分布的不均匀特征逐渐明显,整体承载力也随之提高;锚固长度超过一定取值时,锚固界面软化荷载、抗拔荷载以及整体承载力均趋于定值,与锚固长度无关;计算得到的临界锚固长度与工程实际的锚固长度具有较好的一致性,验证了方法的可行性。 相似文献
5.
An analytical method is developed to provide a better understanding of bolt shearing across joint planes under lateral confinement.
The study was undertaken in conjunction with a laboratory study of the double shearing of bolts in concrete. A review of various
analytical methods is discussed, and the bending behaviour of the bolts is studied under both elastic and plastic conditions.
Issues examined include; hinge point location, the effect of concrete strength on the bolt-bending behaviour; the influence
of bolt axial loading and bolt diameter on the hinge point position with respect to sheared joint planes. It was found that
the applied axial load on the bolt had a significant bearing on the location of the hinge points in different strength concrete,
particularly at low strengths. The hinge point location is also influenced by the bolt diameter. 相似文献
6.
通过一系列剪切模型试验,研究在不同法向力、预应力和锚固情况下锚索对平滑节理面抗剪性能的影响,利用对比试验将销钉力、预应力和轴力增量3种力的抗剪作用分离出来,着重探讨了在剪切过程中3种力对节理面的抗剪贡献,并分析了锚索模拟体的破坏形式。试验结果表明,预应力锚固明显提高了节理面剪切力-位移曲线初始段的抗剪力和剪切刚度,并使得曲线末段表现出塑性强化的特征;预应力大小对加锚节理面抗剪强度的影响与试验条件、节理面状况和锚固角等有关。试验和理论分析表明,剪切位移开始阶段预应力和销钉作用发挥了主要作用,杆体形成塑性铰后轴力增量则起了重要的作用,锚索的破坏一般发生在节理面附近,属于拉剪复合破坏模式。 相似文献
7.
锚杆能够显著增强顺层岩质边坡的稳定性.基于顺层边坡结构效应,应用锚杆加固顺层边坡的力学模型,根据结构力学理论和变形协调关系,建立拉剪作用下全长粘结型锚杆加固顺层边坡抗剪计算的理论分析方法.与相关试验数据进行了比较验证,结果表明顺层边坡锚固抗力模型计算结果与试验结果比较一致,验证了理论模型的合理性.讨论了锚杆倾角、锚杆直径、灌浆体强度、结构面内摩擦角、剪胀角等对加锚顺层岩体抗剪性能的影响.分析表明:锚杆锚固抗力模型能够较好地反映锚杆轴力及横向剪切力对顺层岩质边坡的抗剪作用.锚杆倾角越大,锚杆总的抗力呈减小趋势,而锚杆抗力随剪胀角增大而增加;当锚杆倾角等于内摩擦角时,锚杆抗力达到最大;锚杆抗力随锚杆直径增加而增大;当锚杆直径不变时,锚杆抗力随灌浆体抗压强度增大而有所减小. 相似文献
8.
预应力锚索加固岩体的应力损失分析 总被引：9，自引：0，他引：9
预应力锚索加固岩体的效果取决于预应力的大小。为了保持岩体长期稳定，必须长期保持有足够的预应力。岩体随时间产生的变形、锚索松驰、腐蚀、结构的不同等因素都将造成锚索预应力损失。这对加固效果带来不良影响。本文着重研究岩体随时间的变形产生的预应力损失。 相似文献
9.
通过模型试验研究了竖向荷载作用下砂土中斜桩的荷载传递性状,分析了桩身倾角及长径比对斜桩桩身轴力、弯矩、剪力、桩侧摩阻力及端阻比的影响。试验结果表明：在桩顶竖向荷载作用下,斜桩桩身轴力均小于相应直桩桩身轴力,桩身倾角越大,轴力沿深度衰减得越快,桩长径比越大,轴力沿深度衰减得也越快;斜桩桩身最大弯矩随桩身倾角及长径比的增加而增加,最大弯矩出现的深度与桩身倾角无关,只与长径比相关;不论桩身倾角及长径比的大小,斜桩桩身最大剪力均出现在桩顶截面处,桩身最大剪力随着桩身倾角的增加而增大;桩身倾角越大,斜桩最大摩阻力越大,长径比越大,斜桩最大摩阻力越小,斜桩最大摩阻力出现在桩顶下1/4～1/5桩长处;斜桩端阻比随着桩顶竖向荷载的增加而增大,随着桩身倾角及长径比的增加而减小。 相似文献
10.
Explanation for the widely reported observation that fully grouted reinforcement is more effective in hard rock that behaves as a discontinuum than in soft rock is presented. Analytical solutions are presented for the distribution of displacement and load along an untensioned fully grouted elastic bolt, of specified bond stiffness, which is activated during excavation by either a continuous or discontinuous distribution of rock displacement. The results indicate that significantly higher axial loads are developed for the discontinuous case. Since the mechanics of bond failure depend on the type of bolt and grout used, in the second part of the paper a finite difference formulation is introduced and combined with a non-linear model for the bond behaviour of a cement grouted seven-wire strand cable bolt. The results of a parametric study indicate that, because the bond is frictional and depends on confinement at the borehole wall, for the same profile of rock mass displacement lower loads are developed in soft rock. Furthermore, in soft rock, excavation induced stress changes can cause a dramatic reduction in bond strength, so that, even after significant rock mass displacement, the axial load developed is significantly less than the tensile strength of the cable. A combination of these effects can explain why failures of cable bolted ground involve debonding at the cable–grout interface in soft rock, and why instances of cable rupture are confined to hard, blocky rock masses. 相似文献
11.
岩石在长期荷载作用下表现出典型的蠕变特性,裂隙泥岩在长期荷载作用下的力学性质不同于完整岩石。对甘肃甘谷赵家窑滑坡钻孔取芯的裂隙泥岩开展剪切蠕变试验,探讨轴向压应力、预制裂隙长度等因素对试样剪切蠕变特征的影响。试验结果表明:轴向荷载和裂隙长度对试样剪切蠕变特征有明显的影响。轴向压应力越大,试样剪切蠕变变形越不明显;裂隙越长,试样剪切蠕变变形越显著。应力较低时,如Cvisc模型等蠕变模型能够较好反映泥岩的蠕变力学特性。而在加速蠕变阶段,大多数模型却不能准确体现泥岩蠕变曲线的非线性变化。改进的西原模型克服了传统模型不能对非线性蠕变特征进行描述的缺点,且模型参数较少,能较好地适用工程软弱岩体。不同载荷作用下泥质软岩试样剪切蠕变过程中,裂隙泥岩剪切破坏带形成表现为渐进与突发相结合。泥岩的剪切蠕变力学模型可解释泥岩滑坡的多种现象,边坡潜在滑移带内泥质软岩发生的剪切蠕变则是泥岩滑坡的内在诱因。 相似文献
12.
13.
锚杆对围岩的加固效果和动载响应的数值分析 总被引：3，自引：1，他引：2
利用数值分析软件LS-DYNA3D程序,对锚杆对围岩的加固效果和动态力学性能进行了显示动力分析,比较了洞室围岩是否用锚杆加固时,爆炸波引起的岩体中垂直应力、拱顶位移以及锚杆本身轴向应变的变化特点。结果发现：同毛洞相比较,加固洞室围岩应力较大,拱顶位移较小;通过分析锚杆轴向应变-时程曲线,发现不同安装角的锚杆其轴向应变对动载的响应不同,拱部锚杆先受压后受拉,直墙部锚杆全受拉,两部位锚杆均产生轴向拉应变;将模拟的锚杆应变-时程曲线同模型试验的相应曲线进行了比较,两者一致性较好,其结果为动载作用下坑道围岩锚杆加固的布置方法提供了参考。 相似文献
14.
Results of both triaxial and direct shear tests on reinforced soil samples performed by different investigators have shown that soil dilatancy and extensibility of the reinforcements have a significant effect on the generated tension forces in the inclusions. An appropriate soil--reinforcement load transfer model, integrating the effect of soil dilatancy and reinforcement extensibility is therefore needed to adequately predict forces in the inclusions under expected working loads. This paper present a load transfer model assuming an elastoplastic strain hardening behaviour for the soil and an elastic--perfectly plastic behaviour for the reinforcement. This model is used to analyse the response of the reinforced soil material under triaxial compression loading. A companion paper present the application of this model for numerical simulations of direct shear tests on sand samples reinforced with different types of tension resisting reinforcements. The model allows an evaluation of the effect of various parameters such as mechanical characteristics and dilatancy properties of the soil, extensibility of the reinforcements, and their inclination with respect to the failure surface, on the development of resisting tensile stresses in the reinforcements. A parametric study is conducted to evaluate the effect of these parameters on the behaviour of the reinforced soil material. An attempt is also made to verify the proposed model by comparing numerical predictions with available experimental results of both triaxial and direct shear tests on reinforced soil samples. This model can be used for analysis and design of reinforced soil walls with different types of tension resisting inclusions to predict tension forces under expected working loads. 相似文献
15.
基于小波函数伸缩平移的特性,建立了能反映锚杆界面黏结?软化?滑动力学特性的剪应力?位移非线性本构模型,克服了三折线软化界面模型需要分段分析的复杂性。结合锚固体荷载传递的力学微分方程,推导了锚杆拉拔荷载?位移曲线的解析表达式,并提出了锚固体位移、轴力、周边剪应力的数值计算方法和步骤。通过算例分析,得到不同张拉位移作用下的锚固段位移、轴力和剪应力分布,获得的锚杆拉拔荷载?位移和锚杆轴向力分布计算值与实测值进行了对比分析,验证了该方法的有效性。该方法能准确地反映锚杆在不同荷载下的传力机制,模拟锚杆从弹性工作状态到塑性滑移的全过程。最后,通过参数分析,得到了锚杆锚固长度、轴向刚度以及锚固界面本构参数对锚固效果的影响规律。 相似文献
16.
针对锚杆受压侧岩体或砂浆体反力非线性作用及结构面的剪胀效应问题,基于经典梁理论推导锚杆轴力与轴向变形及横向剪切力与横向变形的理论公式,建立了锚杆抗剪力计算公式。通过加锚结构面直剪试验验证理论计算有效性,并分析结构面剪胀系数、围岩强度、锚杆安装角（倾角）对锚杆变形和抗剪力的影响。结果表明：锚杆抗剪理论计算与室内试验结果吻合较好;结构面剪胀系数越大,越能较快调动锚杆抗剪作用,相反锚杆塑性强化特征越不明显,改善加锚结构面的阻滑抗剪作用,主要依靠结构面固有抗剪强度;随着围岩强度降低,锚杆需经一定变形才能发挥较大抗剪作用,而随着围岩强度增大,锚杆将迅速达到屈服状态,并且锚杆由轴向张拉破坏逐渐转为拉剪破坏;锚杆最优安装角随结构面内摩擦角增大而增大,依据实际工程中结构面内摩擦角取值范围,可估算锚杆最优安装角为30°～68°。 相似文献
17.
锚索锚固力影响因素的试验分析研究 总被引：1，自引：0，他引：1
树脂锚索锚固力的影响因素复杂、锚固机理不完善,造成了支护参数设计不合理,甚至发生围岩加固失败。针对回采巷道顶板岩层含水状况,通过室内锚索拉拔试验,分析研究了锚索锚固长度、孔径、树脂药卷包装膜和水等对锚固力的影响规律,总结出锚索载荷随位移变化的4种形式,以及锚索轴力分布的规律,对树脂锚索的支护参数设计及机理研究具有参考价值。 相似文献
18.
泡沫混凝土作为隧道减震材料在抵抗地震压剪荷载方面具有重要作用,为了研究减震层-衬砌接触面在地震压剪荷载作用下的破坏特征与剪应力演化规律,利用RMT-150C电液伺服试验机开展了二者接触面在不同法向应力下的直剪试验,获得了剪应力-剪切位移、峰值强度、残余强度、剪切刚度的变化规律及接触面的破坏特征和物态变化。根据有限元模拟结果,探究接触面上剪应力的分布及演化规律。研究表明：泡沫混凝土-衬砌接触面的破坏特征受法向应力与泡沫混凝土密度共同影响,其剪应力-剪切位移曲线形态可归结为3种类型,且随泡沫混凝土密度和法向应力的变化可以相互转化;泡沫混凝土密度及法向应力对接触面峰值强度、残余强度及剪切刚度的影响是相互的,且法向应力的影响权重较大。根据剪应力-剪切位移曲线的变化规律,提出了复合指数模型来反映泡沫混凝土-衬砌接触面在压剪作用下损伤演化及摩擦滑移过程,研究结果可以为更加有效的抗减震设计提供一定参考。 相似文献
19.
玄武岩纤维（BFRP）锚杆具有抗拉强度高、耐腐蚀性能好等优点,是岩土锚固结构中钢筋的良好替代品,近年颇受业界关注。通过在黄土地层中开展4组?25 mm BFRP锚杆和钢锚杆的现场拉拔试验,初步研究两种材质锚杆的破坏模式和锚固性能差异。研究结果表明：对于诸如?25 mm类较大直径土层锚杆,拉拔过程中锚固体系的灌浆体内外界面破坏迹象共存,但最终破坏模式受控于灌浆体与土层界面（第二界面）,且BFRP锚杆与砂浆内界面（第一界面）破坏程度明显高于钢锚杆;两种材质锚杆的极限承载力相近,界面黏结强度均随锚固长度的增大而减小;受两种材质锚杆本身的加工工艺和材料力学性能影响,试验中钢锚杆与灌浆体的黏结性能优于BFRP锚杆;相同荷载水平,相同位置处,BFRP锚杆杆体轴力大于钢锚杆,轴力衰减速率略小于钢锚杆;峰值剪应力BFRP锚杆小于钢锚杆。 相似文献
20.
《Geomechanics and Geoengineering》2013,8(4):285-296
ABSTRACTIn this study, uniaxial compression experiments with seven different bedding angles and six numbers of freeze–thaw cycles were conducted to investigate the influences of freeze–thaw cycles on the elastic parameters and the uniaxial compressive strength of slate. The laws of the elastic parameters, uniaxial compressive strength and failure characteristics were analysed, and a new uniaxial compressive strength prediction model that considers the bedding angle and the number of freeze–thaw cycles as control variables was established and verified using the experimental data. The results showed that the uniaxial compressive strength, elastic modulus and shear modulus decreased exponentially with an increasing number of freeze–thaw cycles. However, the Poisson’s ratio increased linearly with an increasing number of freeze–thaw cycles. The uniaxial compressive strength initially decreased and then increased with increasing bedding angle. There are three forms of failure occurred during the tests: when the bedding angle was 0°≤β ≤ 26.6°, the splitting failure and shear failure occurred at the same time; when the bedding angle was 26.6°≤β ≤ 83.0°, sliding failure occurred along the bedding plane; and when the bedding angle was 83.0°≤β ≤ 90°, splitting failure occurred along the axial direction of sample. 相似文献