首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 531 毫秒
1.
Sensitivity of time-lapse seismic to reservoir stress path   总被引：1，自引：1，他引：1  
The change in reservoir pore pressure due to the production of hydrocarbons leads to anisotropic changes in the stress field acting on the reservoir. Reservoir stress path is defined as the ratio of the change in effective horizontal stress to the change in effective vertical stress from the initial reservoir conditions, and strongly influences the depletion‐induced compaction behaviour of the reservoir. Seismic velocities in sandstones vary with stress due to the presence of stress‐sensitive regions within the rock, such as grain boundaries, microcracks, fractures, etc. Since the response of any microcracks and grain boundaries to a change in stress depends on their orientation relative to the principal stress axes, elastic‐wave velocities are sensitive to reservoir stress path. The vertical P‐ and S‐wave velocities, the small‐offset P‐ and SV‐wave normal‐moveout (NMO) velocities, and the P‐wave amplitude‐versus‐offset (AVO) are sensitive to different combinations of vertical and horizontal stress. The relationships between these quantities and the change in stress can be calibrated using a repeat seismic, sonic log, checkshot or vertical seismic profile (VSP) at the location of a well at which the change in reservoir pressure has been measured. Alternatively, the variation of velocity with azimuth and distance from the borehole, obtained by dipole radial profiling, can be used. Having calibrated these relationships, the theory allows the reservoir stress path to be monitored using time‐lapse seismic by combining changes in the vertical P‐wave impedance, changes in the P‐wave NMO and AVO behaviour, and changes in the S‐wave impedance.  相似文献   

2.
The geological storage of carbon dioxide is considered as one of the measures to reduce greenhouse gas emissions and to mitigate global warming. Operators of storage sites are required to demonstrate safe containment and stable behaviour of the storage complex that is achieved by geophysical and geochemical monitoring, combined with reservoir simulations. For site characterization, as well as for imaging the carbon dioxide plume in the reservoir complex and detecting potential leakage, surface and surface‐borehole time‐lapse seismic monitoring surveys are the most widespread and established tools. At the Ketzin pilot site for carbon dioxide storage, permanently installed fibre‐optic cables, initially deployed for distributed temperature sensing, were used as seismic receiver arrays, demonstrating their ability to provide high‐resolution images of the storage formation. A vertical seismic profiling experiment was acquired using 23 source point locations and the daisy‐chained deployment of a fibre‐optic cable in four wells as a receiver array. The data were used to generate a 3D vertical seismic profiling cube, complementing the large‐scale 3D surface seismic measurements by a high resolution image of the reservoir close to the injection well. Stacking long vibro‐sweeps at each source location resulted in vertical seismic profiling shot gathers characterized by a signal‐to‐noise ratio similar to gathers acquired using geophones. A detailed data analysis shows strong dependency of data quality on borehole conditions with significantly better signal‐to‐noise ratio in regions with good coupling conditions.  相似文献   

3.
Permanent downhole sensors provide the eyes and ears to the reservoir and enable monitoring the reservoir conditions on a real‐time basis. In particular, the use of sensors and remotely controlled valves in wells and on the surface, in combination with reservoir flow models provide enormous benefits to reservoir management and oil production. We suggest borehole radar measurements as a promising technique capable to monitor the arrival of undesired fluids in the proximity of production wells. We use 1D modelling to investigate the expected signal magnitude and depth of investigation of a borehole radar sensor operating in an oilfield environment. We restrict the radar applicability to environments where the radar investigation depth can fit the reservoir size necessary to be monitored. Potential applications are steam chamber monitoring in steam assisted gravity drainage processes and water front monitoring in thin oil rim environments. A more sophisticated analysis of the limits of a radar system is carried out through 2D finite‐difference time‐domain simulations. The metal components of the wellbore casing can cause destructive interference with the emitted signal. A high dielectric medium surrounding the production well increases the amplitude of the signal and so the radar performance. Other reservoir constraints are given by the complexity of the reservoir and the dynamic of the fluids. Time‐lapse changes in the heterogeneity of the background formation strongly affect the retrieval of the target reflections and gradual fluid saturation changes reduce the amplitudes of the reflections.  相似文献   

4.
The aim of seismic reservoir monitoring is to map the spatial and temporal distributions and contact interfaces of various hydrocarbon fluids and water within a reservoir rock. During the production of hydrocarbons, the fluids produced are generally displaced by an injection fluid. We discuss possible seismic effects which may occur when the pore volume contains two or more fluids. In particular, we investigate the effect of immiscible pore fluids, i.e. when the pore fluids occupy different parts of the pore volume. The modelling of seismic velocities is performed using a differential effective‐medium theory in which the various pore fluids are allowed to occupy the pore space in different ways. The P‐wave velocity is seen to depend strongly on the bulk modulus of the pore fluids in the most compliant (low aspect ratio) pores. Various scenarios of the microscopic fluid distribution across a gas–oil contact (GOC) zone have been designed, and the corresponding seismic properties modelled. Such GOC transition zones generally give diffuse reflection regions instead of the typical distinct GOC interface. Hence, such transition zones generally should be modelled by finite‐difference or finite‐element techniques. We have combined rock physics modelling and seismic modelling to simulate the seismic responses of some gas–oil zones, applying various fluid‐distribution models. The seismic responses may vary both in the reflection time, amplitude and phase characteristics. Our results indicate that when performing a reservoir monitoring experiment, erroneous conclusions about a GOC movement may be drawn if the microscopic fluid‐distribution effects are neglected.  相似文献   

5.
目前,针对陆相薄互层油藏实施时移地震监测尚没有明显的突破,加强时移地震方法、理论的研究和应用,对于我国时移地震监测技术的发展和应用具有积极的意义.根据油藏工程理论,在详细分析火烧油层对储层物性影响的基础上,结合已有的实验室岩石物理测量结果,重点就稠油热采过程中温度的剧烈变化对储层岩石和孔隙流体弹性特性的影响进行了较为详细的分析.并开展了薄互层油藏火烧油层地震正演模拟研究.结果表明,在稠油热采过程中,高温高压不仅会使得孔隙流体特性发生显著的改变,而且储层岩石本身弹性特性的变化也非常明显.即使是对于薄层或薄互层,两方面共同的变化将使得稠油热采前后储层弹性特性产生巨大的差异,进而引起显著的地震异常.因此,开展陆相薄互层稠油热采时移地震监测,不仅具有坚实的岩石物理基础,而且具有切实的可行性.  相似文献   

6.
Of particular concern in the monitoring of gas injection for the purposes of storage, disposal or improved oil recovery is the exact spatial distribution of the gas volumes in the subsurface. In principle this requirement is addressed by the use of 4D seismic data, although it is recognized that the seismic response still largely provides a qualitative estimate of moved subsurface fluids. Exact quantitative evaluation of fluid distributions and associated saturations remains a challenge to be solved. Here, an attempt has been made to produce mapped quantitative estimates of the gas volume injected into a clastic reservoir. Despite good results using three accurately repeated seismic surveys, time‐delay and amplitude attributes reveal fine‐scale differences though large‐scale agreement in the estimated fluid movement. These differences indicate disparities in the nature of the two attributes themselves, which can be explained by several possible causes. Of most impact are the effects of processing and migration, wave interference effects and noise from non‐repeatability of the seismic surveys. This subject highlights the need for a more careful consideration in 4D acquisition, amplitude processing and use of true amplitude preserving attributes in quantitative interpretation.  相似文献   

7.
Seismic wave propagation through a fluid-saturated poroelastic layer might be strongly affected by media heterogeneities. Via incorporating controlled laboratory simulation experiments, we extend previous studies of time-lapse seismic effects to evaluate the wave scattering influence of the heterogeneous nature of porous permeable media and the associated amplification effects on 4D seismic response characteristics of reservoir fluid substitution. A physical model consisted of stratified thin layers of shale and porous sandstone reservoir with rock heterogeneities was built based on the geological data of a real hydrocarbon-saturated reservoir in Northeast China. Multi-surveys data of good quality were acquired by filling poroelastic reservoir layers with gas, water and oil in sequence. Experimental observations show that reservoir heterogeneity effect causes significantly magnified abnormal responses to the fluid-saturated media. Specifically, reflection signatures of the gas-filled reservoir are dramatically deviated from those of the liquid fluid-filled reservoir, compared with ones of the homogeneous media. By removing the influences unrelated to reservoir property alterations, 4D seismic estimates of travel-time and frequency-dependent characteristic are reasonably consistent with fluid variations. Nevertheless, strong 4D amplitude difference anomalies might not correspond to the regions where fluid variations occur. We also find that 4D seismic difference attributes are evident between oil- and water-filled models, whereas significant between oil- and gas-filled models. Meanwhile, rock physics modelling results reveal the predicted 4D seismic differences are obviously smaller than those calculated from seismic observations. The results in this paper, therefore, implicate that the effect of a reservoir's heterogeneous nature might be beneficial for hydrocarbons detection as well as monitoring small variations in pore fluids.  相似文献   

8.
4D seismic is widely used to remotely monitor fluid movement in subsurface reservoirs. This technique is especially effective offshore where high survey repeatability can be achieved. It comes as no surprise that the first 4D seismic that successfully monitored the CO2 sequestration process was recorded offshore in the Sleipner field, North Sea. In the case of land projects, poor repeatability of the land seismic data due to low S/N ratio often obscures the time‐lapse seismic signal. Hence for a successful on shore monitoring program improving seismic repeatability is essential. Stage 2 of the CO2CRC Otway project involves an injection of a small amount (around 15,000 tonnes) of CO2/CH4 gas mixture into a saline aquifer at a depth of approximately 1.5 km. Previous studies at this site showed that seismic repeatability is relatively low due to variations in weather conditions, near surface geology and farming activities. In order to improve time‐lapse seismic monitoring capabilities, a permanent receiver array can be utilised to improve signal to noise ratio and hence repeatability. A small‐scale trial of such an array was conducted at the Otway site in June 2012. A set of 25 geophones was installed in 3 m deep boreholes in parallel to the same number of surface geophones. In addition, four geophones were placed into boreholes of 1–12 m depth. In order to assess the gain in the signal‐to‐noise ratio and repeatability, both active and passive seismic surveys were carried out. The surveys were conducted in relatively poor weather conditions, with rain, strong wind and thunderstorms. With such an amplified background noise level, we found that the noise level for buried geophones is on average 20 dB lower compared to the surface geophones. The levels of repeatability for borehole geophones estimated around direct wave, reflected wave and ground roll are twice as high as for the surface geophones. Both borehole and surface geophones produce the best repeatability in the 30–90 Hz frequency range. The influence of burying depth on S/N ratio and repeatability shows that significant improvement in repeatability can be reached at a depth of 3 m. The level of repeatability remains relatively constant between 3 and 12 m depths.  相似文献   

9.
The analysis of seismic ambient noise acquired during temporary or permanent microseismic monitoring campaigns (e.g., improved/enhanced oil recovery monitoring, surveillance of induced seismicity) is potentially well suited for time‐lapse studies based on seismic interferometry. No additional data acquisition required, ambient noise processing can be automatized to a high degree, and seismic interferometry is very sensitive to small medium changes. Thus there is an opportunity for detection and monitoring of velocity variations in a reservoir at negligible additional cost and effort. Data and results are presented from an ambient noise interferometry study applied to two wells in a producing oil field in Romania. Borehole microseismic monitoring on three component geophones was performed for four weeks, concurrent with a water‐flooding phase for improved oil recovery from a reservoir in ca. 1 km depth. Both low‐frequency (2 Hz–50 Hz) P‐ and S‐waves propagating through the vertical borehole arrays were reconstructed from ambient noise by the virtual source method. The obtained interferograms clearly indicate an origin of the ambient seismic energy from above the arrays, thus suggesting surface activities as sources. It is shown that ambient noise from time periods as short as 30 seconds is sufficient to obtain robust interferograms. Sonic log data confirm that the vertical and horizontal components comprise first arrivals of P‐wave and S‐waves, respectively. The consistency and high quality of the interferograms throughout the entire observation period further indicate that the high‐frequency part (up to 100 Hz) represents the scattered wave field. The temporal variation of apparent velocities based on first‐arrival times partly correlates with the water injection rate and occurrence of microseismic events. It is concluded that borehole ambient noise interferometry in production settings is a potentially useful method for permanent reservoir monitoring due to its high sensitivity and robustness.  相似文献   

10.
我国具有丰富的稠油资源,但国内外针对陆相薄互层稠油油藏热采动态的时移地震监测研究还很少.通过分析火烧油层对储层的影响,结合已有的岩石物理测量结果,建立了薄互层油藏火烧油层模型,开展了地震正演模拟研究,并给出了应用实例.结果表明,稠油热采(注蒸汽、火烧油层、注热水)会引起储层岩石和孔隙流体弹性特性的显著改变,从而导致明显的地震属性差异;时移地震可以用来划分油层中高温区范围,跟踪高温前缘等.在陆相薄互层稠油田热采开发中,利用时移地震来监测油田开发的全过程是可行的.  相似文献   

11.
In hydraulic fracturing treatments, locating not only hydraulic fractures but also any pre‐existing natural fractures and faults in a subsurface reservoir is very important. Hydraulic fractures can be tracked by locating microseismic events, but to identify the locations of natural fractures, an additional technique is required. In this paper, we present a method to image pre‐existing fractures and faults near a borehole with virtual reverse vertical seismic profiling data or virtual single‐well profiling data (limited to seismic reflection data) created from microseismic monitoring using seismic interferometry. The virtual source data contain reflections from natural fractures and faults, and these features can be imaged by applying migration to the virtual source data. However, the imaging zone of fractures in the proposed method is strongly dependent on the geographic extent of the microseismic events and the location and direction of the fracture. To verify our method, we produced virtual reverse vertical seismic profiling and single‐well profiling data from synthetic microseismic data and compared them with data from real sources in the same relative position as the virtual sources. The results show that the reflection travel times from the fractures in the virtual source data agree well with travel times in the real‐source data. By applying pre‐stack depth migration to the virtual source data, images of the natural fractures were obtained with accurate locations. However, the migrated section of the single‐well profiling data with both real and virtual sources contained spurious fracture images on the opposite side of the borehole. In the case of virtual single‐well profiling data, we could produce correct migration images of fractures by adopting directional redatuming for which the occurrence region of microseismic events is divided into several subdivisions, and fractures located only on the opposite side of the borehole are imaged for each subdivision.  相似文献   

12.
Repeatability of seismic data plays a crucial role in time‐lapse seismic analysis. There are several factors that can decrease the repeatability, such as positioning errors, varying tide, source variations, velocity changes in the water layer (marine data) and undesired effects of various processing steps. In this work, the complexity of overburden structure, as an inherent parameter that can affect the repeatability, is studied. A multi‐azimuth three‐dimensional vertical‐seismic‐profiling data set with 10 000 shots is used to study the relationship between overburden structure and repeatability of seismic data. In most repeatability studies, two data sets are compared, but here a single data set has been used because a significant proportion of the 10 000 shots are so close to each other that a repeatability versus positioning error is possible. We find that the repeatability decreases by a factor of approximately 2 under an overburden lens. Furthermore, we find that the X‐ and Y‐components have approximately the same sensitivity to positioning errors as the Z‐component (for the same events) in this three‐dimensional vertical‐seismic‐profiling experiment. This indicates that in an area with complex overburden, positioning errors between monitor and base seismic surveys are significantly more critical than outside such an area. This study is based on a three‐dimensional three‐component vertical‐seismic‐profiling data set from a North Sea reservoir and care should be taken when extrapolating these observations into a general four‐dimensional framework.  相似文献   

13.
We present the analysis of a multi-azimuth vertical seismic profiling data set that has been acquired in a tight gas field with the objective of characterizing fracture distributions using seismic anisotropy. We investigate different measurements of anisotropy, which are shear-wave splitting, P-wave traveltime anisotropy and azimuthal amplitude variation with offset. We find that for our field case shear-wave splitting is the most robust measure of azimuthal anisotropy, which is clearly observed over two distinct intervals in the target. We compare the results of the vertical seismic profiling analysis with other borehole data from the same well. Cross-dipole sonic and Formation MicroImager data from the reservoir section suggest that no open fractures intersect the well or are present within half a metre of the borehole wall. Furthermore, a detailed dispersion analysis of the sonic scanner data provides no indication of stress-induced seismic anisotropy along the logged borehole section. We therefore explain the azimuthal anisotropy measured in the vertical seismic profiling data with a model that contains discrete fracture corridors, which do not intersect the well itself but lie within the vertical seismic profiling investigation radius. We show that such a model can reproduce some basic characteristics of azimuthal anisotropy observed in the vertical seismic profiling data. The model is also consistent with well test data that suggest the presence of a fracture corridor away from the well. With this study we demonstrate the necessity of integrating different data types that investigate different scales of rock volume and can provide complementary information for understanding the characteristics of fracture networks in the subsurface.  相似文献   

14.
The possibility of using 4D seismic data for monitoring pressure depletion in the low‐porosity, tight gas‐bearing Rotliegende sandstones of the UK Southern Gas Basin is investigated. The focus here is on whether fractures in the upper part of the reservoir, known to enhance productivity, can also enhance the time‐lapse seismic response. The study uses laboratory data to evaluate core‐plug stress sensitivity, published data for the stress behaviour of the fractures, followed by petro‐elastic and 4D seismic modelling of both the fractured and unfractured formation. The magnitude of the resultant 4D signatures suggests that production‐induced changes in the unfractured sands are unlikely to be observed except perhaps with highly repeatable time‐lapse surveys. On the other hand, the presence of fractures could render production effects visible in dedicated 4D acquisition or prestack parallel processed data. If present however, the signature will be sporadic, as fractures in the area are known to exist in clusters. The 4D signature may be enhanced further by certain classes of vertical geological variability and also areas of high reservoir pressure. The strongest evidence of depletion is expected to be time‐shifts seen at the base of the Rotliegende reservoir.  相似文献   

15.
To advance and optimize secondary and tertiary oil recovery techniques, it is essential to know the areal propagation and distribution of the injected fluids in the subsurface. We investigate the applicability of controlled‐source electromagnetic methods to monitor fluid movements in a German oilfield (Bockstedt, onshore Northwest Germany) as injected brines (highly saline formation water) have much lower electrical resistivity than the oil within the reservoir. The main focus of this study is on controlled‐source electromagnetic simulations to test the sensitivity of various source–receiver configurations. The background model for the simulations is based on two‐dimensional inversion of magnetotelluric data gathered across the oil field and calibrated with resistivity logs. Three‐dimensional modelling results suggest that controlled‐source electromagnetic methods are sensitive to resistivity changes at reservoir depths, but the effect is difficult to resolve with surface measurements only. Resolution increases significantly if sensors or transmitters can be placed in observation wells closer to the reservoir. In particular, observation of the vertical electric field component in shallow boreholes and/or use of source configurations consisting of combinations of vertical and horizontal dipoles are promising. Preliminary results from a borehole‐to‐surface controlled‐source electromagnetic field survey carried out in spring 2014 are in good agreement with the modelling studies.  相似文献   

16.
Time‐lapse seismic surveying has become an accepted tool for reservoir monitoring applications, thus placing a high premium on data repeatability. One factor affecting data repeatability is the influence of the rough sea‐surface on the ghost reflection and the resulting seismic wavelets of the sources and receivers. During data analysis, the sea‐surface is normally assumed to be stationary and, indeed, to be flat. The non‐flatness of the sea‐surface introduces amplitude and phase perturbations to the source and receiver responses and these can affect the time‐lapse image. We simulated the influence of rough sea‐surfaces on seismic data acquisition. For a typical seismic line with a 48‐fold stack, a 2‐m significant‐wave‐height sea introduces RMS errors of about 5–10% into the stacked data. This level of error is probably not important for structural imaging but could be significant for time‐lapse surveying when the expected difference anomaly is small. The errors are distributed differently for sources and receivers because of the different ways they are towed. Furthermore, the source wavelet is determined by the sea shape at the moment the shot is fired, whereas the receiver wavelet is time‐varying because the sea moves significantly during the seismic record.  相似文献   

17.
油藏水驱开采时移地震监测岩石物理基础测量   总被引：9，自引：0，他引：9       下载免费PDF全文
岩石物理测量是油藏水驱开采时移地震监测的基础.在实验室对来自胜利油田的5块岩石样品模拟储层条件进行了水驱和气驱动态岩石物理弹性测量,重点分析了流体替换、温度、孔隙压力对岩石纵、横波速度的影响.实验表明,在水驱情形下,由于流体替换和温度、孔隙压力变化所引起的岩石纵横波速度的变化均很小,实施时移地震监测具有较大的风险性.相比之下,气驱可能引起较为明显的纵波速度变化,有利于时移地震监测的实施.进一步完善实验方法、丰富实验内容、是今后时移地震岩石物理实验研究的主要任务.  相似文献   

18.
Time‐lapse seismics is the methodology of choice for remotely monitoring changes in oil/gas reservoir depletion, reservoir stimulation or CO2 sequestration, due to good sensitivity and resolving power at depths up to several kilometres. This method is now routinely applied offshore, however, the use of time‐lapse methodology onshore is relatively rare. The main reason for this is the relatively high cost of commercial seismic acquisition on land. A widespread belief of a relatively poor repeatability of land seismic data prevents rapid growth in the number of land time‐lapse surveys. Considering that CO2 sequestration on land is becoming a necessity, there is a great need to evaluate the feasibility of time‐lapse seismics for monitoring. Therefore, an understanding of the factors influencing repeatability of land seismics and evaluating limitations of the method is crucially important for its application in many CO2 sequestration projects. We analyse several repeated 2D and 3D surveys acquired within the Otway CO2 sequestration pilot project (operated by the Cooperative Research Centre for Greenhouse Technologies, CO2CRC) in Australia, in order to determine the principal limitations of land time‐lapse seismic repeatability and investigate the influence of the main factors affecting it. Our findings are that the intrinsic signal‐to‐noise ratio (S/N, signal to coherent and background noise levels) and the normalized‐root‐mean‐square (NRMS) difference are controlled by the source strength and source type. However, the post‐stack S/N ratio and corresponding NRMS residuals are controlled mainly by the data fold. For very high‐fold data, the source strength and source type are less critical.  相似文献   

19.
It is common for at least one monitoring well to be located proximally to a production well. This presents the possibility of applying crosswell technologies to resolve a range of earth properties between the wells. We present both field and synthetic examples of dual well walk-away vertical seismic profiling in vertical wells and show how the direct arrivals from a virtual source may be used to create velocity images between the wells. The synthetic experiments highlight the potential of virtual source crosswell tomography where large numbers of closely spaced receivers can be deployed in multiple wells. The field experiment is completed in two monitoring wells at an aquifer storage and recovery site near Perth, Western Australia. For this site, the crosswell velocity distribution recovered from inversion of travel times between in-hole virtual sources and receivers is highly consistent with what is expected from sonic logging and detailed zero-offset vertical seismic profiling. When compared to conventional walkaway vertical seismic profiling, the only additional effort required to complete dual-well walkaway vertical seismic profiling is the deployment of seismic sensors in the second well. The significant advantage of virtual source crosswell tomography is realised where strong near surface heterogeneity results in large travel time statics.  相似文献   

20.
Fluid depletion within a compacting reservoir can lead to significant stress and strain changes and potentially severe geomechanical issues, both inside and outside the reservoir. We extend previous research of time‐lapse seismic interpretation by incorporating synthetic near‐offset and full‐offset common‐midpoint reflection data using anisotropic ray tracing to investigate uncertainties in time‐lapse seismic observations. The time‐lapse seismic simulations use dynamic elasticity models built from hydro‐geomechanical simulation output and a stress‐dependent rock physics model. The reservoir model is a conceptual two‐fault graben reservoir, where we allow the fault fluid‐flow transmissibility to vary from high to low to simulate non‐compartmentalized and compartmentalized reservoirs, respectively. The results indicate time‐lapse seismic amplitude changes and travel‐time shifts can be used to qualitatively identify reservoir compartmentalization. Due to the high repeatability and good quality of the time‐lapse synthetic dataset, the estimated travel‐time shifts and amplitude changes for near‐offset data match the true model subsurface changes with minimal errors. A 1D velocity–strain relation was used to estimate the vertical velocity change for the reservoir bottom interface by applying zero‐offset time shifts from both the near‐offset and full‐offset measurements. For near‐offset data, the estimated P‐wave velocity changes were within 10% of the true value. However, for full‐offset data, time‐lapse attributes are quantitatively reliable using standard time‐lapse seismic methods when an updated velocity model is used rather than the baseline model.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号