共查询到18条相似文献，搜索用时 156 毫秒
1.
硬悬挂钻井隔水管涡激振动特性研究 总被引：1，自引：0，他引：1
针对深水钻井过程中遭遇强台风,基于安全性考虑要求钻井平台悬挂隔水管提前撤离的问题,采用软件SHEAR7针对HYSY981钻井平台硬悬挂隔水管系统避台风撤离作业过程中,受南海一年一遇海流作用时诱发涡激振动(VIV)的情况,研究航速与悬挂长度对VIV特性的影响。研究表明,浮力块覆盖率越高,隔水管系统张力越小;浮力块分布对隔水管系统VIV响应影响较大,25%交错布置方案VIV响应最弱。隔水管并非越短越好,要综合考虑洋流剖面、隔水管配置和平台航行的影响;在不同悬挂长度及航行条件下的VIV响应,在撤离作业前应尽量避免在高流速区布置浮力单根,撤离作业时应尽量采用顺流而避免平台逆流航向。 相似文献
2.
建立了软悬挂状态下隔水管动力分析模型,采用有限单元法对模型进行离散,结合Newmark-β法对动态方程求解,并对模型进行验证,最后选取南海某口深水井实际参数,对软悬挂状态下隔水管动力特性进行分析。研究结果表明:软悬挂状态下隔水管底端横向位移最大,顶部铰接处弯矩最大。软悬挂状态下,隔水管横向位移与弯矩随着海底隔水管总成(LMRP)重量增加而减小,随着平台运动速度、平台航向与海流方向夹角增大而增大;回收隔水管减小悬挂长度有利于减小最大横向位移,但会造成弯矩轻微增加;采用旋转刚度适当较大的挠性接头则有利于减小隔水管挠性接头以下整体位移与弯矩。研究成果为钻井平台避台撤离时隔水管的安全提供理论指导。 相似文献
3.
南海海域台风频发,对于深水浮式钻井平台,常规避台模式要求回收所有隔水管,但是在深水、超深水海域,这种应对台风的方案有其局限性。据测算,水深超过1 500 m时,台风准备时间(回收所有隔水管、处理井口的作业时间)超过4天,而目前天气预报的水平只能提前4～5天,因此常规避台难度极大,经常会遭遇到还没有起完隔水管,台风已经逼近平台位置的情况,悬挂隔水管成为一种不得不面对的防台避台方案。硬悬挂和软悬挂是目前悬挂隔水管两种常见的模式,由于软悬挂能够补偿和缓解钻井船升沉施加在悬挂隔水管上的动态载荷,因此业内普遍认为软悬挂模式在提高悬挂隔水管对海洋环境的适应能力方面具有一定的优势,但是常规的软悬挂模式作业程序复杂,而且实施过程中存在伸缩节、张力器液缸等相关设备冲程超标的风险。通过对隔水管悬挂状态下横向和轴向的动力响应进行分析,确定了限制隔水管悬挂安全的主要因素,针对隔水管应力超标和转角过大、干涉等风险,设计了一种具有加装扶正器的锥形悬挂短节;针对悬挂隔水管的轴向压缩风险,研制了一种具有补偿功能的隔水管悬挂装置,降低了悬挂隔水管动态载荷产生轴向压缩和动态应力超标的风险。定量评估表明使用新型隔水管悬挂系统,可以将常规的悬挂窗口由不足10年一遇波流环境条件提高到满足100年一遇的波流环境条件,大大提高了悬挂隔水管的安全性。 相似文献
4.
深水钻井隔水管紧急脱离后的反冲响应 总被引：1，自引：0，他引：1
深水钻井中,在恶劣海况或浮式平台定位失效等情况下,需紧急断开隔水管与水下防喷器的连接。隔水管突然脱离后会加速向上反冲,如果反冲作用控制不当,可能威胁钻井平台、隔水管体和水下井口的安全。介绍了国外隔水管紧急脱离与反冲响应的研究情况,分析了隔水管紧急脱离的原因与程序、脱离后的反冲过程、反冲控制方式和成功脱离标准、反冲响应的分析方法。建议:由于南海深水海况复杂,作业者需制定紧急脱离的预案和作业规程,并进行紧急脱离操作培训;由于隔水管紧急脱离后的反冲响应涉及多个非线性瞬态过程,研究者应该开展隔水管紧急脱离测试和反冲响应模拟计算,开发隔水管反冲响应分析软件。 相似文献
5.
6.
深海采矿作为新领域资源重点开发项目,国外已开展部分试验研究,国内现阶段仅停留在重点设备部件级功能验证,还未开展过系统整体联动,距离海洋油气等正在进行的规模化商业开采还有很大距离。本文以深海采矿系统整体联动模型为基础,与海洋油气工程作业平台技术模型进行对比,对整体联动风险点进行深度分析,并根据重点风险部件开展其悬挂模式、力学模型研究,探讨深海采矿系统整体联动时应急撤离的策略。研究总结了深海采矿系统整体联动的特点,提出了管道摇摆幅度超出设计范围、平台升沉行程超出伸缩冲程范围等两大关键风险点、提升硬管受力分析方法和对应的应急撤离方案,对深海采矿工程总体设计和工程实施具有指导意义和参考价值。 相似文献
7.
8.
9.
通过在震源船上部署3套GPS接收机,并对3个点的位置信息进行汇总和压缩,利用北斗短报文将压缩后的位置信息推送到陆海联测指挥部,实现对震源船航速、航向的实时监控.根据3个点位信息计算的实时震源船航向,有助于准确把握震源船在进行固定点悬停激发时的航向,克服了以往使用前后两个时刻推算的平均航向代替实时航向等问题.使用我国自主知识产权的北斗短报文进行通讯,大大提高了系统的安全性、可靠性和稳定性;同时陆海联测指挥部可以实时查看震源船是否按事先设定的测线、事先设定的速度和航向进行作业,有效保障了监控平台对震源船的监控,进一步提升安全生产的风险控制能力. 相似文献
10.
基于船位监控系统的拖网捕捞努力量提取方法研究 总被引：6，自引：1，他引：5
为了基于船位监控系统提取拖网捕捞努力量,通过统计航速获得3个峰值,拖网作业在第2个峰值,即1~2.1 m/s,拖网作业航向差一般在–50°~50°。利用航速、航向差阈值设定,把拖网船状态划分为慢速、作业、航行,然后提取出捕捞作业状态点,1 423艘拖网船共提取到处于捕捞状态的点318 433个,合计拖网捕捞时间15 921 h,利用反距离加权插值法生成捕捞强度分布变化趋势图。捕捞努力量在渔业资源研究中是重要的参考值之一,与传统的捕捞努力量计算方法相比,该方法具有实时、大范围、快速、分辨率高的特点,能够用于辅助渔业资源保护。 相似文献
11.
陵水17-2气田是国内首个采用钢悬链立管的深水气田。以该气田钢悬链立管(SCR)为例,结合国外经验确定了影响强度的主要因素,利用FLEXCOM软件建立了强度分析模型并进行了敏感性分析。通过对比分析,得到以下结论:管线重量公差较其他因素对立管强度有着更明显的影响,管线重量的正负公差分别对立管触地区和悬挂区强度影响较大,其中等效应力最大增加了13.5%;内部压力的变化对重质管线强度影响较轻质管线明显;柔性节点刚度对立管强度的影响主要集中在悬挂区;立管安装误差对悬挂区和触地区等效应力影响为6.5%～9.5%。为陵水17-2气田及其他类似工程提供参考和借鉴。 相似文献
12.
In recent years, offshore reservoirs have been developed in deeper and deeper water environments. Steel catenary risers (SCRs) are being considered in deepwater development such as Northern North Sea. SCRs used in conjunction with a semi-submersible or floating production, storage and offloading (FPSO) in deepwater harsh environments present significant design challenges. The large vertical motions at the semi or FPSO induce severe riser response, which results in difficulty meeting strength and fatigue criteria at the hang off and touch down point locations. To improve the understanding of SCR behaviour and increase the confidence in the design of such systems in deepwater harsh environments, a parametric study on a SCR connected to a semi-submersible was carried out in this paper to deal with the factors that mainly influence the loading condition and fatigue life of the riser. Weight-optimized configurations were applied during the course of riser design. Riflex combined with DeepC was the primary analysis tool used for the long-term response of the nonlinear SCR structure simulations, which requires a large amount of computer time. Hence, the parameters affecting the efficiency and accuracy of the simulations have also been studied during the analysis process. 相似文献
13.
基于ABAQUS/AQUA模块,当Spar平台发生涡激运动时,对与平台相连接的柔性立管进行时域动态响应分析,得到了不同折合速度下柔性立管的应力响应曲线.对立管触地区域和悬垂段进行了细化的分析,并利用S-N曲线和Miner线性累积损伤理论对平台涡激运动引起的柔性立管疲劳损伤进行了计算.研究结果表明:平台涡激运动对立管触地区域和悬垂段的影响较大,这两部分最容易在长时间的工作中产生疲劳损伤.特别是平台运动到近点时,立管触地区域受到的应力急剧增加,这个区域是立管工作的危险区域,应该特别注意.该研究结论可以作为立管结构设计和海底铺设时的参考,通过增加立管触地区域的结构强度和优化铺设方式,从而来提高立管的疲劳寿命和系统的安全性. 相似文献
14.
As drilling operations move into remote locations and extreme water depths, recoil analysis requires more careful considerations and the incidence of emergency disconnect is increased inevitably. To accurately capture the recoil dynamics of a deep-water riser in an emergency disconnect scenario, researchers typically focus on modelling the influential subsystems (e.g., the tensioner, the mud discharge and seawater refilling process) which can be solved in the preprocessing, and then the determined parameters are transmitted into an existing global riser analysis software. Distinctively, the current study devotes efforts into the coupling effects resulting from that the suspended riser reacts the platform heave motion via the tensioner system in the course of recoil and the discharging fluid column follows the oscillation of the riser in the mud discharge process. Four simulation models are established based on lumped mass method employing different formulas for the top boundary condition of the riser and the discharging flow acceleration. It demonstrates that the coupling effects discussed above can significantly affect the recoil behavior during the transition phase from initial disconnect to the final hang-off state. It is recommended to develop a fully- coupled integrated model for recoil analysis and anti-recoil control system design before extreme deep-water applications. 相似文献
15.
针对在南海海域频发的台风自然灾害,考虑海况随机性、结构随机性以及作业参数的随机性,采用梯度投影确定取样点的响应面法,分别建立P2D、D2P和P2P(P指生产立管,D指钻井立管)三种作业模式下TLP串行立管系统的结构极限状态方程。并在建立立管可靠性分析模型的基础上,确定一种立管可靠度计算方法。算例结合南海某TLP平台给出了上述方法的具体应用。研究表明,10年一遇台风情况下,P2D、D2P和P2P三种工况中生产立管系统的失效概率均小于0.001%,钻井立管系统的可靠度分别为0.016%和0.113%。在大于200年一遇的强台风情况下,P2P工况时的上下游生产立管系统失效概率均大于0.32%和0.018%。因此建议10年一遇台风情况下,停止钻井立管作业;在大于200年一遇的强台风情况下,停止生产立管作业。研究结果可为南海TLP立管系统可靠度评估及安全作业技术支持。 相似文献
16.
During the drilling of ultra-deep-water subsea petroleum wells, a blow-out preventer (BOP), a piece of safety equipment, must be assembled on the wellhead. The BOP is suspended using the drilling riser during the wellhead approach operation, and the riser's top end is connected to the floating platform rig. This article presents a feedback control system for the automatic approach of the BOP to the wellhead. Compared to state-of-the-art controls, ours does not require ancillary thrusters installed alongside the riser nor inclination sensors atop of the drilling riser. Additionally, our proposed control embeds a closed-loop dynamic positioning system, thus retaining the characteristics of the original control system and adding an extra closed-loop. This eases implementation of the BOP approach control to an existing platform. To calculate the optimal gains for the BOP controller, we assume a linear system for the riser, including only the pendulum-shape. The simulation is carried out using nonlinear models for both riser and floating platform. We assume an International Towing Tank Conference standard semi-submersible platform, coupled with a 3000-m free-hanging vertical riser for the time-domain simulation. The results show the BOP tracking to be a step-shaped input signal under current and wave loads. A discussion of the performance of feedback control under different environmental loads is also included. 相似文献
17.
Felipe Alexander Vargas Bazán Edison Castro Prates de Lima Marcos Queija de Siqueira Elizabeth Frauches Netto Siqueira Carlos Alberto Duarte de Lemos 《Applied Ocean Research》2011,33(4):344-365
In riser structural systems, the region where the riser is connected to the platform is critical due to the development of high stress levels. To reduce the stress concentration in this region, bend stiffeners and stress joints are used in order to provide a gradual stiffness transition between the riser and the platform. The present paper presents an optimization design approach for bend stiffeners and stress joints, using a slender beam procedure for the connection joint analysis and an evolution strategies multi-objective optimization algorithm. This approach produces similar results when compared to a finite element analysis of the complete riser, but with significant reduction of computational costs. Numerical examples are presented, showing the efficiency and robustness of the suggested methodology. 相似文献
18.
In the present study, the dynamic and fatigue characteristics of two types of stress joints are investigated under ocean environmental condition. Connected with the riser and the platform, stress joint at the vessel hang-off position should be one of the main critical design challenges for a steel catenary riser (SCR) in deepwater. When the riser is under a high pressure and deepwater working condition, the stress state for the joint is more complex, and the fatigue damage is easy to occur at this position. Stress joint discussed in this paper includes two types: Tapered Stress Joint (TSJ) and Sleeved Stress Joint (SSJ), and multiaxial fatigue analysis results are given for comparison. Global dynamic analysis for an SCR is performed first, and then the local boundary conditions obtained from the previous analysis are applied to the stress joint FE model for the later dynamic and multiaxial fatigue analysis. Results indicate that the stress level is far lower than the yield limit of material and the damage induced by fatigue needs more attention. Besides, the damage character of the two types of stress joints differs: for TSJ, the place where the stress joint connects with the riser is easy to occur fatigue damage; for SSJ, the most probable position is at the place where the end of the inner sleeve pipe contacts with the riser body. Compared with SSJ, TSJ shows a higher stress level but better fatigue performance, and it will have a higher material cost. In consideration of various factors, designers should choose the most suitable type and also geometric parameters. 相似文献