首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 115 毫秒
1.
The objective of this paper was to investigate the THM-coupled responses of the storage formation and caprock, induced by gas production, CO2-EGR (enhanced gas recovery), and CO2-storage. A generic 3D planer model (20,000?×?3,000?×?100?m, consisting of 1,200?m overburden, 100?m caprock, 200?m gas reservoir, and 1,500?m base rock) is adopted for the simulation process using the integrated code TOUGH2/EOS7C-FLAC3D and the multi-purpose simulator OpenGeoSys. Both simulators agree that the CO2-EGR phase under a balanced injection rate (31,500?tons/year) will cause almost no change in the reservoir pressure. The gas recovery rate increases 1.4?% in the 5-year CO2-EGR phase, and a better EGR effect could be achieved by increasing the distance between injection and production wells (e.g., 5.83?% for 5?km distance, instead of 1.2?km in this study). Under the considered conditions there is no evidence of plastic deformation and both reservoir and caprock behave elastically at all operation stages. The stress path could be predicted analytically and the results show that the isotropic and extensional stress regime will switch to the compressional stress regime, when the pore pressure rises to a specific level. Both simulators agree regarding modification of the reservoir stress state. With further CO2-injection tension failure in reservoir could occur, but shear failure will never happen under these conditions. Using TOUGH-FLAC, a scenario case is also analyzed with the assumption that the reservoir is naturally fractured. The specific analysis shows that the maximal storage pressure is 13.6?MPa which is determined by the penetration criterion of the caprock.  相似文献   

2.
The feasibility of CO2 storage and enhanced gas recovery (EGR) effects in the mature Altmark natural gas field in Central Germany has been studied in this paper. The investigations were comprehensive and comprise the characterization of the litho- and diagenetic facies, mineral content, geochemical composition, the petrophysical properties of the reservoir rocks with respect to their potential reactivity to CO2 as well as reservoir simulation studies to evaluate the CO2 wellbore injectivity and displacement efficiency of the residual gas by the injected CO2. The Rotliegend sediments of the Altmark pilot injection area exhibit distinct mineralogical, geochemical, and petrophysical features related to litho- and diagenetic facies types. The reservoir rock reactivity to CO2 has been studied in autoclave experiments and associated effects on two-phase transport properties have been examined by means of routine and special core analysis before and after the laboratory runs. Dissolution of calcite and anhydrite during the short-term treatments leading to the enhancements of permeability and porosity as well as stabilization of the water saturation relevant for CO2 injection have been observed. Numerical simulation of the injection process and EGR effects in a sector of the Altmark field coupled with a wellbore model revealed the possibility of injecting the CO2 gas at temperatures as low as 10 °C and pressures around 40 bar achieving effective inflow in the reservoir without phase transition in the wellbore. The small ratio of injected CO2 volume versus reservoir volume indicated no significant EGR effects. However, the retention and storage capacity of CO2 will be maximized. The migration/extension of CO2 varies as a function of heterogeneity both in the layers and in the reservoir. The investigation of CO2 extension and pressure propagation suggested no breakthrough of CO2 at the prospective production well during the 3-year injection period studied.  相似文献   

3.
The joint research project CLEAN was conducted in the years 2008?C2011 by a German research and development (R&D) alliance of 16 partners from science and industry. The project was set-up as pilot project to investigate the processes relevant to enhanced gas recovery (EGR) by the injection of CO2 into a subfield of the almost depleted Altmark natural gas field. Despite the setback that permission for active injection was not issued by the mining authority during the period of the project, important results fostering the understanding of processes linked with EGR were achieved. Work carried out led to a comprehensive evaluation of the EGR potential of the Altmark field and the Altensalzwedel subfield in particular. The calculated safety margins emphasize that technical well integrity of the 12 examined boreholes is given for EGR without a need for any further intervention. The laboratory and field tests confirm that the Altensalzwedel subfield is suitable for the injection of 100,000?t of CO2. Numerical simulations provide sound predictions for the efficiency and safety of the EGR technology based on the CO2 injection. The development and testing of different monitoring techniques facilitate an improved surveying of CO2 storage sites in general. The CLEAN results provide the technological, logistic and conceptual prerequisites for implementing a CO2-based EGR project in the Altmark and provide a benchmark for similar projects in the world.  相似文献   

4.
Numerical models are essential tools in fully understanding the fate of injected CO2 for commercial-scale sequestration projects and should be included in the life cycle of a project. Common practice involves modeling the behavior of CO2 during and after injection using site-specific reservoir and caprock properties. Little has been done to systematically evaluate and compare the effects of a broad but realistic range of reservoir and caprock properties on potential CO2 leakage through caprocks. This effort requires sampling the physically measurable range of caprock and reservoir properties, and performing numerical simulations of CO2 migration and leakage. In this study, factors affecting CO2 leakage through intact caprocks are identified. Their physical ranges are determined from the literature from various field sites. A quasi-Monte Carlo sampling approach is used such that the full range of caprock and reservoir properties can be evaluated without bias and redundant simulations. For each set of sampled properties, the migration of injected CO2 is simulated for up to 200 years using the water–salt–CO2 operational mode of the STOMP simulator. Preliminary results show that critical factors determining CO2 leakage rate through caprocks are, in decreasing order of significance, the caprock thickness, caprock permeability, reservoir permeability, caprock porosity, and reservoir porosity. This study provides a function for prediction of potential CO2 leakage risk due to permeation of intact caprock and identifies a range of acceptable seal thicknesses and permeability for sequestration projects. The study includes an evaluation of the dependence of CO2 injectivity on reservoir properties.  相似文献   

5.
Carbon dioxide (CO2) sequestration in depleted sandstone hydrocarbon reservoirs could be complicated by a number of geomechanical problems associated with well drilling, completions, and CO2 injection. The initial production of hydrocarbons (gas or oil) and the resulting pressure depletion as well as associated reduction in horizontal stresses (e.g., fracture gradient) narrow the operational drilling mud weight window, which could exacerbate wellbore instabilities while infill drilling. Well completions (casing, liners, etc.) may experience solids flowback to the injector wells when injection is interrupted due to CO2 supply or during required system maintenance. CO2 injection alters the pressure and temperature in the near wellbore region, which could cause fault reactivation or thermal fracturing. In addition, the injection pressure may exceed the maximum sustainable storage pressure, and cause fracturing and fault reactivation within the reservoirs or bounding formations. A systematic approach has been developed for geomechanical assessments for CO2 storage in depleted reservoirs. The approach requires a robust field geomechanical model with its components derived from drilling and production data as well as from wireline logs of historical wells. This approach is described in detail in this paper together with a recent study on a depleted gas field in the North Sea considered for CO2 sequestration. The particular case study shows that there is a limitation on maximum allowable well inclinations, 45° if aligning with the maximum horizontal stress direction and 65° if aligning with the minimum horizontal stress direction, beyond which wellbore failure would become critical while drilling. Evaluation of sanding risks indicates no sand control installations would be needed for injector wells. Fracturing and faulting assessments confirm that the fracturing pressure of caprock is significantly higher than the planned CO2 injection and storage pressures for an ideal case, in which the total field horizontal stresses increase with the reservoir re-pressurization in a manner opposite to their reduction with the reservoir depletion. However, as the most pessimistic case of assuming the total horizontal stresses staying the same over the CO2 injection, faulting could be reactivated on a fault with the least favorable geometry once the reservoir pressure reaches approximately 7.7 MPa. In addition, the initial CO2 injection could lead to a high risk that a fault with a cohesion of less than 5.1 MPa could be activated due to the significant effect of reduced temperature on the field stresses around the injection site.  相似文献   

6.
Capturing CO2 from point sources and storing it in geologic formations is a potential option for allaying the CO2 level in the atmosphere. In order to evaluate the effect of geological storage of CO2 on rock-water interaction, batch experiments were performed on sandstone samples taken from the Altmark reservoir, Germany, under in situ conditions of 125 °C and 50 bar CO2 partial pressure. Two sets of experiments were performed on pulverized sample material placed inside a closed batch reactor in (a) CO2 saturated and (b) CO2 free environment for 5, 9 and 14 days. A 3M NaCl brine was used in both cases to mimic the reservoir formation water. For the “CO2 free” environment, Ar was used as a pressure medium. The sandstone was mainly composed of quartz, feldspars, anhydrite, calcite, illite and chlorite minerals. Chemical analyses of the liquid phase suggested dissolution of both calcite and anhydrite in both cases. However, dissolution of calcite was more pronounced in the presence of CO2. In addition, the presence of CO2 enhanced dissolution of feldspar minerals. Solid phase analysis by X-ray diffraction and Mössbauer spectroscopy did not show any secondary mineral precipitation. Moreover, Mössbauer analysis did not show any evidence of significant changes in redox conditions. Calculations of total dissolved solids’ concentrations indicated that the extent of mineral dissolution was enhanced by a factor of approximately 1.5 during the injection of CO2, which might improve the injectivity and storage capacity of the targeted reservoir. The experimental data provide a basis for numerical simulations to evaluate the effect of injected CO2 on long-term geochemical alteration at reservoir scale.  相似文献   

7.
Baseline monitoring at the proposed enhanced gas recovery site in Altmark (Germany) was carried out in combination with theoretical and laboratory investigations to describe and predict the principles of expected stable carbon isotope and dissolved inorganic carbon (DIC) trends during CO2 injection in reservoirs. This provides fundamental data for site-specific characterisation for monitoring purposes. Baseline ??13C values at the Altmark site ranged between ?1.8 and ?11.5??? and DIC values were about 2?mmol?L?1. These baseline values form the basis for a theoretical study on the influences of the ambient reservoir conditions on the state of geochemical and isotope equilibrium of the reservoir fluids. Transferring this theoretical study to the Altmark site enables predictions on geochemical trends during potential injection. Assuming that CO2 would be injected at the Altmark site to pCO2?=?100?bar and with a ??13C of ?30???, at isotopic and geochemical equilibrium, ??13CDIC values would approach this end-member, and DIC concentrations of 1,000?mmol L?1 would be expected. Laboratory experiments were conducted at low pCO2 levels (4?C35?bars) to mimic the approach of a CO2 plume at a monitoring well. These results support field investigations from other sites: that ??13CDIC is a sensitive tool for monitoring CO2 migration in the subsurface and simultaneously allows quantification of geochemical trapping of CO2.  相似文献   

8.
Dissolution?Cprecipitation phenomena induced by CO2 injection to Altmark Permian sandstone were observed through laboratory experiments carried out under simulated reservoir conditions (125?°C and 50 bars of pressure). The rock sample was collected from the Altmark gas reservoir, which is being considered for enhanced gas recovery. Two sets of experiments were performed with pulverized rock samples in a closed batch reactor with either pure water (run 1) or 3?M aqueous NaCl solution (run 2) and reacted with injected CO2 for 3, 5, and 9?days. The liquid samples were analyzed by inductively coupled plasma optical emission spectroscopy and total reflection X-ray fluorescence, where the latter proved to be a feasible alternative to conventional analytical techniques, especially since only small sample volumes (about 10???l) are needed. Chemical analysis for both fluids (water and NaCl brine) indicated a significant dissolution of calcite and anhydrite in the solution, which might be a crucial process during CO2 injection. The brine solution enhanced the dissolution of calcite and anhydrite compared to pure water at the beginning of the reaction. Moreover, the progressive higher Si4+/Al3+ molar ratios (in average by a factor of 3) in the brine experiments indicated quartz dissolution. Thermodynamic calculations of mineral saturation indices highlighted the dissolution of the Ca-bearing minerals, which was in agreement with experimental results. Modeling enabled an evaluation of the dissolution processes of minerals in a low-salinity region, yet hindrances to model more saline conditions emphasize the need for further laboratory studies in order to parameterize models for deep aquifer conditions.  相似文献   

9.
Significant potential exists for CO2 sequestration in coalbed methane reservoirs of the Black Warrior basin. Reservoir simulation is an appropriate approach to estimate both the storage capacity and methane recovery enhancement. However, prior to a reliable reservoir modeling and simulation, conducting an accurate and comprehensive reservoir characterization study is necessary. The purpose of the present study is twofold: (a) to provide a rigorous reservoir characterization study required for modeling Mary Lee coal group in the Blue Creek field of the Black Warrior basin; (b) to run fluid flow simulations to predict the performance of ECBM process applied to an under pressured zone of the Mary Lee coal group. According to the current well configuration of Blue Creek field, three applicable well patterns, namely a direct line drive, an inverted 5-spot and a normal 5-spot were separately (i.e., in three distinct cases) used for simulating ECBM. Simulations were run on an approximately 32 ha (80-acre) drainage area, and included coal matrix shrinkage/swelling effects. The injected gas was assumed to be pure CO2. Using an inverted 5-spot pattern, simulations predicted that after 7.5 years of CO2 injection, approximately 32,000 tonnes of CO2 would be sequestered per 32 ha of this zone and that methane recovery would be enhanced by 36 %. Using a normal 5-spot pattern, CO2 breakthrough would occur 2.4 years earlier, and about 40,000 tonnes CO2 would be sequestered. However, methane production would be enhanced by 33 %. Considering methane recovery enhancement, direct line drive pattern delivered poor results in comparison with two other patterns. As expected, the results also showed that CO2 injection would increase water production.  相似文献   

10.
This study examined the impacts of reservoir properties on carbon dioxide (CO2) migration after subsurface injection and evaluated the possibility of characterizing reservoir properties using CO2 monitoring data such as spatial–temporal distributions of gas pressure, which can be reasonably monitored in practice. The injection reservoir was assumed to be located 1,400–1,500 m below the ground surface such that CO2 remained in the supercritical state. The reservoir was assumed to contain layers with alternating conductive and resistive properties, which is analogous to actual geological formations such as the Mount Simon Sandstone unit. The CO2 injection simulation used a cylindrical grid setting in which the injection well was situated at the center of the domain, which extended out 8,000 m from the injection well. The CO2 migration was simulated using the latest version of the simulator, subsurface transport over multiple phases (the water–salt–CO2–energy module), developed by Pacific Northwest National Laboratory. A nonlinear parameter estimation and optimization modeling software package, Parameter ESTimation (PEST), is adopted for automated reservoir parameter estimation. The effects of data quality, data worth, and data redundancy were explored regarding the detectability of reservoir parameters using gas pressure monitoring data, by comparing PEST inversion results using data with different levels of noises, various numbers of monitoring wells and locations, and different data collection spacing and temporal sampling intervals. This study yielded insight into the use of CO2 monitoring data for reservoir characterization and how to design the monitoring system to optimize data worth and reduce data redundancy. The feasibility of using CO2 saturation data for improving reservoir characterization was also discussed.  相似文献   

11.
This paper presents an innovative well abandonment concept developed for the long-term containment of CO2 in depleted Rotliegend gas reservoirs. The new concept aims at amending the conventional standard well abandonment procedure, taking advantage of the natural creeping ability of the thick, homogeneous Zechstein rock salt formation located around 3,000?m in depth (Altmark area) and consists of four main sealing units: (1) a standard sealing element with cement from the reservoir to the impermeable caprock, (2) a salt plug created in the formerly reamed section of casing within the plastic Zechstein (Upper Permian) rock salt formation, (3) two bridge plugs at the bottom and top of the salt plug and (4) a standard sealing element with cement from the top bridge plug until the ground surface. This site-specific study mainly lays emphasis on the development and field testing of the naturally created salt plug, as a key component of the long-term wellbore sealing concept. Comprehensive numerical simulations conducted prior to and during the field test in 2010 and 2011 successfully predicted the evolution of convergence using downhole measurement data. Preliminary results comprise (1) proven convergence of the rock salt formation, (2) a successful coring and (3) restored integrity of Zechstein salt formation, as proven by the formation integrity test. Based on these results, the new long-term sealing concept has been successfully tested at the Altmark natural gas field and successful application of the concept on other sites with similar geological conditions is foreseen to be likely.  相似文献   

12.
The most suitable candidates for subsurface storage of CO2 are depleted gas fields. Their ability to retain CO2 can however be influenced by the effect which impurities in the CO2 stream (e.g. H2S and SO2) have on the mineralogy of reservoir and seal. In order to investigate the effects of SO2 we carried out laboratory experiments on reservoir and cap rock core samples from gas fields in the northeast of the Netherlands. The rock samples were contained in reactor vessels for 30 days in contact with CO2 and 100 ppm SO2 under in-situ conditions (300 bar, 100 °C). The vessels also contained brine with the same composition as in the actual reservoir. Furthermore equilibrium modeling was carried out using PHREEQC software in order to model the experiments on caprock samples.After the experiments the permeability of the reservoir samples had increased by a factor of 1.2–2.2 as a result of dissolution of primary reservoir minerals. Analysis of the associated brine samples before and after the experiments showed that concentrations of K, Si and Al had increased, indicative of silicate mineral dissolution.In the caprock samples, composed of carbonate and anhydrite minerals, permeability changed by a factor of 0.79–23. The increase in permeability is proportional to the amount of carbonate in the caprock. With higher carbonate content in comparison with anhydrite the permeability increase is higher due to the additional carbonate dissolution. This dependency of permeability variations was verified by the modeling study. Hence, caprock with a higher anhydrite content in comparison with carbonate minerals has a lower risk of leakage after co-injection of 100 ppmv SO2 with CO2.  相似文献   

13.
Geochemical interactions of brine–rock–gas have a significant impact on the stability and integrity of the caprock for long-term CO2 geological storage. Invasion of CO2 into the caprock from the storage reservoir by (1) molecular diffusion of dissolved CO2, (2) CO2-water two-phase flow after capillary breakthrough, and (3) CO2 flow through existing open fractures may alter the mineralogy, porosity, and mechanical strength of the caprock due to the mineral dissolution or precipitation. This determines the self-enhancement or self-sealing efficiency of the caprock. In this paper, two types of caprock, a clay-rich shale and a mudstone, are considered for the modeling analyses of the self-sealing and self-enhancement phenomena. The clay-rich shale taken from the Jianghan Basin of China is used as the base-case model. The results are compared with a mudstone caprock which is compositionally very different than the clay-rich shale. We focus on mineral alterations induced by the invasion of CO2, feedback on medium properties such as porosity, and the self-sealing efficiency of the caprock. A number of sensitivity simulations are performed using the multiphase reactive transport code TOUGHREACT to identify the major minerals that have an impact on the caprock’s self-sealing efficiency. Our model results indicate that under the same hydrogeological conditions, the mudstone is more suitable to be used as a caprock. The sealing distances are barely different in the two types of caprock, both being about 0.6 m far from the interface between the reservoir and caprock. However, the times of occurrence of sealing are considerably different. For the mudstone model, the self-sealing occurs at the beginning of simulation, while for the clay-rich shale model, the porosity begins to decline only after 100 years. At the bottom of the clay-rich shale column, the porosity declines to 0.034, while that of mudstone declines to 0.02. The sensitive minerals in the clay-rich shale model are calcite, magnesite, and smectite-Ca. Anhydrite and illite provide Ca2+ and Mg2+ to the sensitive minerals for their precipitation. The mudstone model simulation is divided into three stages. There are different governing minerals in different stages, and the effect of the reservoir formation water on the alteration of sensitive minerals is significant.  相似文献   

14.
A pilot site for CO2 storage in coal seams was set-up in the Upper Silesian Coal Basin in Poland in the scope of the RECOPOL project, funded by the European Commission. About 760 tons CO2 were injected into the reservoir from August 2004 to June 2005. Breakthrough of the injected CO2 was established, which resulted in the production of about 10% of the injected CO2 in this period. This paper reports on activities performed under the European Commission project MOVECBM that aimed at the assessment of the storage performance of the reservoir in the follow-up period, i.e. whether the injected CO2 was adsorbed onto the coal or whether it was still present as free gas in the pore space. The injection well was used for this purpose, as the production well had to be abandoned for permitting reasons. Several operational periods can be defined between the last injection in June 2005 and the abandonment of the well in October 2007. In the first period the well was shut-in to observe the pressure fall-off, from about 15.0 MPa at the wellhead after the last injection until about 4.5 MPa at the end of 2005. This pressure fall-off curve showed that the reservoir permeability was very low. This seemed to confirm the observed swelling of the coal during the injection period. In the first months of 2006 the pressure at the wellhead was decreased by releasing gas in a controlled way. The amount and composition of the gas were measured. As a result of the pressure reduction, the well flooded with water. A production pump was placed on the former injection well, enabling active production from the coal from March to September 2007. Results of these operations showed that whereas the gas production rates were as expected based on the experience with the production well, the water production was remarkably low. This could be related to permeability issues or, alternatively, indicate a drying effect of the CO2 in the reservoir. Further, the gas composition showed a predominance of CO2 over CH4 during the gas release that changed gradually into a predominance of CH4 over CO2 during the production phase. Although stabilization was not reached within the given production period, the composition approached a 60% methane, 40% CO2 ratio. This indicates that the exchange of these gases is more complex than often envisaged. After removal of the pump the well was filled with water, which ceased the gas release. This indicates that the pressure in the reservoir was back to its original, hydrostatic, state. As the total volume of CO2 produced was only a fraction of the amount that was injected, it can be concluded that the CO2 was taken up by the coal and is currently adsorbed. This gives confidence in the long-term stability of the injected CO2.  相似文献   

15.
Numerical simulations of CO2 migration for the period June 2008–December 2011 were performed based on a unique data set including a recently revised static geological 3D model of the reservoir formation of the Ketzin pilot site in Brandenburg, Germany. We applied the industrial standard ECLIPSE 100 and scientific TOUGH2-MP simulators for this task and implemented a workflow to allow for integration of complex model geometries from the Petrel software package into TOUGH2-MP. Definition of a near- and a far-field well area allowed us to apply suitable permeability modifiers, and thus to successfully match simulation results with pressure measurements and arrival times in observation wells. Coincidence was achieved for CO2 arrival times with deviations in the range of 5.5–15 % and pressure values in the injection well CO2 Ktzi 201/2007 and the observation well CO2 Ktzi 202/2007 with even smaller deviations. It is shown that the integration of unique operational and observation data in the workflow improves the setup of the geological model. Within such an iteration loop model uncertainties are reduced and enable advanced predictions for future reservoir behaviour with regard to pressure development and CO2 plume migration in the storage formation at the Ketzin pilot site supporting the implementation of monitoring campaigns and guiding site operation.  相似文献   

16.
During 2003–2006, a pilot project of alternating water and CO2 injection was performed on a limited part of the Upper Miocene sandstone oil reservoir of the Ivani? Field. During the test period oil and gas recovery was significantly increased. Additionally 4,440 m3 of oil and 2.26 × 106 m3 of gas were produced. It has initiated further modelling of sandstone reservoirs in the Ivani? Field in order to calculate volumes available for CO2 injection for the purpose of increasing hydrocarbon production from depleted sandstone reservoirs in the entire Croatian part of the Pannonian Basin System. In the first phase, modelling was based on results of laboratory testing on the core samples. It considered applying analogies with world-known projects of CO2 subsurface storage and its usage to enhance hydrocarbon production. In the second phase, reservoir variables were analysed by variograms and subsequently mapped in order to reach lithological heterogeneities and to determine reliable average values of reservoir volumes. Data on porosity, depth and reservoir thickness for the “Gamma 3” and the “Gamma 4” reservoirs, are mapped by the ordinary kriging technique. Calculated volume of CO2 expressed at standard condition which can be injected in the main reservoirs of the Ivani? Field at near miscible conditions is above 15.5 billion m3.  相似文献   

17.
This paper reports a preliminary investigation of CO2 sequestration and seal integrity at Teapot Dome oil field, Wyoming, USA, with the objective of predicting the potential risk of CO2 leakage along reservoir-bounding faults. CO2 injection into reservoirs creates anomalously high pore pressure at the top of the reservoir that could potentially hydraulically fracture the caprock or trigger slip on reservoir-bounding faults. The Tensleep Formation, a Pennsylvanian age eolian sandstone is evaluated as the target horizon for a pilot CO2 EOR-carbon storage experiment, in a three-way closure trap against a bounding fault, termed the S1 fault. A preliminary geomechanical model of the Tensleep Formation has been developed to evaluate the potential for CO2 injection inducing slip on the S1 fault and thus threatening seal integrity. Uncertainties in the stress tensor and fault geometry have been incorporated into the analysis using Monte Carlo simulation. The authors find that even the most pessimistic risk scenario would require ∼10 MPa of excess pressure to cause the S1 fault to reactivate and provide a potential leakage pathway. This would correspond to a CO2 column height of ∼1,500 m, whereas the structural closure of the Tensleep Formation in the pilot injection area does not exceed 100 m. It is therefore apparent that CO2 injection is not likely to compromise the S1 fault stability. Better constraint of the least principal stress is needed to establish a more reliable estimate of the maximum reservoir pressure required to hydrofracture the caprock.  相似文献   

18.
The Huntly coalfield has significant coal deposits that contain biogenically-sourced methane. The coals are subbituminous in rank and Eocene in age and have been previously characterised with relatively low to moderate measured gas (CH4) contents (2–4 m3/ton). The CO2 holding capacity is relatively high (18.0 m3/ton) compared with that of CH4 (2.6 m3/ton) and N2 (0.7 m3/ton) at the same pressure (4 MPa; all as received basis). The geothermal gradient is also quite high at 55 °C/km.A study has been conducted which simulates enhancement of methane recovery (ECBM) from these deposits using a new version of the TOUGH2 (version 2) reservoir simulator (ECBM-TOUGH2) that can handle non-isothermal, multi-phase flows of mixtures of water, CH4, CO2 and N2. The initial phase of the simulation is CH4 production for the first 5 years of the field history. The model indicates that methane production can be significantly improved (from less than 80% recovery to nearly 90%) through injection of CO2. However, although an increase in the rate of CO2 injection increases the amount of CO2 sequestered, the methane recovery (because of earlier breakthrough with increasing injection rate) decreases. Modeling of pure N2 injection produced little enhanced CH4 production. The injection of a hypothetical flue gas mixture (CO2 and N2) also produced little increase in CH4 production. This is related to the low adsorption capacity of the Huntly coal to N2 which results in almost instantaneous breakthrough into the production well.  相似文献   

19.
Geological storage of CO2 is considered a solution for reducing the excess CO2 released into the atmosphere. Low permeability caprocks physically trap CO2 injected into underlying porous reservoirs. Injection leads to increasing pore pressure and reduced effective stress, increasing the likelihood of exceeding the capillary entry pressure of the caprocks and of caprock fracturing. Assessing on how the different phases of CO2 flow through caprock matrix and fractures is important for assessing CO2 storage security. Fractures are considered to represent preferential flow paths in the caprock for the escape of CO2. Here we present a new experimental rig which allows 38 mm diameter fractured caprock samples recovered from depths of up to 4 km to be exposed to supercritical CO2 (scCO2) under in situ conditions of pressure, temperature and geochemistry. In contrast to expectations, the results indicate that scCO2 will not flow through tight natural caprock fractures, even with a differential pressure across the fractured sample in excess of 51 MPa. However, below the critical point where CO2 enters its gas phase, the CO2 flows readily through the caprock fractures. This indicates the possibility of a critical threshold of fracture aperture size which controls CO2 flow along the fracture.  相似文献   

20.
CO2 is now considered as a novel heat transmission fluid to extract geothermal energy. It can achieve the goal of energy exploitation and CO2 geological sequestration. Taking Zhacanggou as research area, a “Three-spot” well pattern (one injection with two production), “wellbore–reservoir” coupled model is built, and a constant injection rate is set up. A fully coupled wellbore–reservoir simulator—T2Well—is introduced to study the flow mechanism of CO2 working as heat transmission fluid, the variance pattern of each physical field, the influence of CO2 injection rate on heat extraction and the potential and sustainability of heat resource in Guide region. The density profile variance resulting from temperature differences of two wells can help the system achieve “self-circulation” by siphon phenomenon, which is more significant in higher injection rate cases. The density of CO2 is under the effect of both pressure and temperature; moreover, it has a counter effect on temperature and pressure. The feedback makes the flow process in wellbore more complex. In low injection rate scenarios, the temperature has a dominating impact on the fluid density, while in high rate scenario, pressure plays a more important role. In most scenarios, it basically keeps stable during 30-year operation. The decline of production temperature is <5 °C. However, for some high injection rate cases (75 and 100 kg/s), due to the heat depletion in reservoir, there is a dramatic decline for production temperature and heat extraction rate. Therefore, a 50-kg/s CO2 injection rate is more suitable for “Three-spot” well pattern in Guide region.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号