共查询到20条相似文献，搜索用时 15 毫秒
1.
Calculation of Hydro-Dynamic Stability of the Soil Inside Bucket in the Process of Bucket Foundation Penetration 总被引：1，自引：0，他引：1
—The offshore platform with bucket foundations is a new type of offshore platform that distin-guishes from traditional template platforms by replacing driven piles with bucket foundations.The suctionpenentration of bucket foundation is a complicated hydro-dynamic process.The key of this process is theseepage field caused by the difference of pressure applied on purpose inside and outside the bucket.The ap-pearance and developement of seepage field has a decisive influence on the suction penetration process.Inthis study,the finite element analysis method is applied to the dynamic simulation of the seepage field ofsuction penetration of bucket foundation.A criterion is suggested to distinguish the hydro-dynamic stabili-ty of the soil inside the bucket according to the critical hydraulic gradient method.The reliability of themodel and its applicability to engineering practice have been proved through comparison between the re-sults of model test and finite element calculation. 相似文献
2.
海上平台桶基沉贯渗流场的有限元法数值模拟 总被引：3，自引：1，他引：2
桶形基础平台是一种新型的海洋平台,这种型式的平台与传统的导管架式平台的主要区别在于采用桶形基础代替打下桩基础,桶形基础的负压沉贯过程是一个复杂的水动力过程,其关键在于主动脉施加的桶内外压力差产生渗流场,渗流场的形成与发展对于负压沉贯有决定性的影响。本文用有限元分析方法对桶形基础负压沉贯流流场进行动态模拟,建立了桶形基础负压沉贯过程中渗流场的有限元分析模型,模型试验的结果与按有限元分析计算模型得一的 相似文献
3.
讨论了浅海桶形基础平台负压沉贯渗流场有限元分析方法.通过模型实验结果与有限元分析结果的对比,验证有限元法的可靠性.将有限元法用于桶形基础平台负压沉贯渗流场的计算,得到沉贯过程中许用负压随插深的变化,用于指导平台就位施工时的负压控制.不同插深时,相应许用负压下的桶内、外壁渗流水头和水头梯度分布的计算结果,用于沉贯阻力的计算. 相似文献
4.
Suction buckets differ with their easy and cost-efficient installation technique from other foundation types for offshore wind turbines. For successful completion of their installation process, suction is essential, but the imposed seepage leads to the changes in states of the soil in and around the bucket. Especially, a loosening of soil inside the bucket affects the load carrying behaviour of bucket subjected to repetitive loading resulting from environmental conditions. In this study, the behaviour of buckets under cyclic axial compressive loads with considering a possible loosening and related changes in permeability of soil inside the bucket is investigated numerically. In the framework of finite element analysis, a fully coupled two-phase model and a hypoplastic constitutive model are used to describe the saturated sandy soil behaviour under repetitive loading. The porosity-permeability variation is taken into account by Kozeny–Carman relationship. Special attention is dedicated to load carrying behaviour of bucket top plate, inner and outer skirt as well as base and their changes resulting from a loosening of soil inside the bucket with variable aspect ratio. For this purpose, cyclic axial compressive loads which cause an attenuation and progressive failure of soil-bucket system response are considered. The main findings on the changes in load carrying behaviour of bucket are presented and discussed. 相似文献
5.
海上平台桶基负压沉贯阻力与土体稳定数值计算研究 总被引：3，自引：0，他引：3
用有限元分析方法对桶形基础负压沉贯过程中流场进行动态模拟,提出桶形基础沉贯阻力计算方法和土体稳定有限计算方法,提出桶内土体稳定性判断准则,计算结果表明所提方法是合理的,并具有工程实用性。 相似文献
6.
7.
8.
A concept design, named integrated suction foundation, is proposed for a tension leg platform (TLP) in deep ocean. The most important improvement in comparing with the traditional one is that a pressure-resistant storage module is designed. It utilizes the high hydrostatic pressure in deep ocean to drive water into the module to generate negative pressure for bucket suction. This work aims to further approve the feasibility of the concept design in the aspect of penetration installation and the uplift force in-place. Seepage is generated during suction penetration, and can have both positive and negative effects on penetration process. To study the effect of seepage on the penetration process of the integrated suction foundation, finite element analysis (FEA) is carried out in this work. In particular, an improved methodology to calculate the penetration resistance is proposed for the integrated suction foundation with respect to the reduction factor of penetration resistance. The maximum allowable negative pressure during suction penetration is calculated with the critical hydraulic gradient method through FEA. The simulation results of the penetration process show that the integrated suction foundation can be installed safely. Moreover, the uplift resistance of the integrated suction foundation is calculated and the feasibility of the integrated suction foundation working on-site is verified. In all, the analysis in this work further approves the feasibility of the integrated suction foundation for TLPs in deep ocean applications. 相似文献
9.
The seepage field generated by suction penetration of a bucket foundation into sea floor is numerically simulated with a finite element method. The water head and its gradient on both sides of the bucket wall in the seepage field are computed and the results are applied to the calculation of penetration resistance versus penetration depth. Also, allowable suction pressures with various penetration depths are provided for platform installation. The engineering parameters given in this paper were adopted in the design of the first platform (CB20B) with suction-penetrated buckets as foundations in China. This platform has successfully been launched into operation for the offshore oilfield development at the Yellow River Submersed Delta. 相似文献
10.
为了得到桶基础承受风、浪动荷载的承载性能,结合我国东海地质条件,统计中国东海2010—2020年浅、深海风速和最大海浪数据,通过计算得到风浪荷载并制成ABAQUS软件幅值曲线施加到海上风电吸力桶基础上,分析了吸力桶基础在动荷载作用下的承载特性。结果表明：吸力桶基础受风、浪荷载影响明显,桶基础迎力面受到风浪动荷载产生拉拔现象。在浅海区,桶基础在风浪荷载作用下桶身自上而下变形不协调,风浪荷载最大的10月份桶基础迎力面最大位移超出了规范0.02D的限制,基础失稳;桶基础背力面受压变形较小。在深海区,桶基础在风浪荷载作用下桶身自上而下变形相对协调,施加风浪荷载后桶体迎力面最大位移为14.9 mm,整体上迎力面位移比背力面位移大4 mm,桶体处于稳定状态。相较浅海区的吸力桶单桶结构,深海区吸力桶结构由于尺寸增加,桶体的稳定性得到提高,说明吸力桶结构的尺寸对稳定性起决定性作用。 相似文献
11.
针对海上风电负压桶型基础,以提高桶基水平承载性能和降低结构动力响应为目的,提出了一种加装稳定翼的负压桶型基础型式。通过在桶身设置一组稳定翼,使得桶周土抗力得以充分利用。以单立柱负压桶基为例,建立桶土全实体有限元模型,进行了静力分析和包括模态分析、瞬态分析、谱分析在内的动力分析。结果表明:稳定翼的设置增强了桶基水平承载性能;水平位移和动力响应显著减小;结构低阶固有频率略有提高。 相似文献
12.
用于海洋平台的吸力式桩桶基础作为一种新型平台基础正逐渐成为人们研究的重点。为研究吸力式桩桶单桩基础的受力特性,对V-H（竖向—水平）联合荷载作用下的吸力式单桩基础桩土的承载特性进行了数值模拟,并将数值模拟的有限元解通过与API规范中对p-y曲线的计算方法进行对比来验证有限元模型的可行性,最后采用分级作用力的加载方式对其破坏包络曲线进行绘制,并推导出相应的函数表达式。研究表明,采用ABAQUS有限元分析软件对吸力式桩桶进行数值模拟是可行的,随着对吸力式桩桶所施加V-H联合荷载的不断增大,吸力式桩桶所能体现的应力和弯矩极限值也在随之增大,其位移变化主要在施加荷载的区域附近,最后在联合荷载作用下所体现的极限承载状态,即包络曲线大致呈四分之一的椭圆形状。 相似文献
13.
Suction caissons are considered as an alternative foundation solution for offshore wind turbines. In the present study, three-dimensional finite element (FE) analyses are performed to assess the behavior of a bucket foundation and soil supporting the bucket under cyclic and monotonic loading conditions. A parametric study is also performed for a wide range of bucket geometries and two different soil densities. The results indicate that bucket geometry and soil properties significantly affect the foundation response due to cyclic loading conditions. The bucket with the smallest geometry installed in medium dense soil exhibits the lowest stiffness in initial loading and then with the progress of cyclic loads experiences lower stiffness compared to the caissons with larger geometries. The sensitivity of the foundation response to the soil density is higher than its geometry. The bucket under the lowest vertical load experiences the lowest stiffness in both virgin loading and during the progress of cyclic loads. The highest soil displacement is observed near the lid at the interior of the bucket. Stresses caused by cyclic loading belong to certain ranges. Additionally, increases in the skirt length result in increases in the stress ranges and shift the range to the right side. With respect to the monotonic loading conditions, normalized diagrams are proposed that can be used for the preliminary design of suction bucket foundations. 相似文献
14.
以一6.7 MW风机为研究对象，提出了一种适用于30~50 m水深的海上风电倒Y形导管架筒型基础结构型式，采用三维精细有限元模型对结构的受力特性展开研究，包括结构的自振特性以及在随机风浪流荷载作用下的动力响应。研究结果表明，倒Y形导管架筒型基础采用“三腿变六腿”导管架的结构型式，能够更加有效的将上部荷载传递至下部筒型基础，具有较好的受力特性和传力体系；整机结构的前两阶自振频率均在风机允许运行的频率范围内；在50年一遇极端随机风浪流荷载作用下，整机结构的位移响应和应力响应，均可满足结构安全使用要求。 相似文献
15.
吸力式导管架基础具备高承载力、高施工效率、高环境友好度、低造价等特点,使用其作为海上风电底部支撑结构有利于产业的规模化发展,实现上述愿景的前提在于使筒型基础顺利安装以满足设计要求。基于此,在不同初始施加泵压下,对吸力式导管架的沉贯效率特征值、基础内外围渗流变化、筒裙端部土压力特点进行探究。通过抱桩器使吸力式导管架在吸力安装过程中仅具备竖向自由度,从而进行纯沉贯试验。结果表明：初始泵压2 kPa时沉贯效率特征值最高;沉贯过程中基础外围渗流水压小于基础内围渗流水压;筒裙外侧所受土压要大于筒壁内侧所受土压力。 相似文献
16.
17.
近海海床表层多为软黏土或淤泥质土,为探究海床表层软土对海上风电宽浅式筒型基础承载特性的影响,以中国广东某海域风电场为背景,通过有限元分析的方法,研究竖向、水平、弯矩荷载作用下软土层厚度和土体强度对基础极限承载力、破坏模式以及筒基土压力分布的影响。研究结果表明:当软土层厚度小于H/2(H为筒裙高度)时,单向荷载作用下宽浅式筒型基础极限承载力随软土层厚度的增加呈线性减小的趋势;当软土层厚度大于H/2后,承载力降低速率逐渐增大。表层软土的存在,使得塑性区范围缩小,软土层内土体塑性破坏更加明显。竖向荷载作用下,随软土层厚度的增大,筒顶承载先减小后增大,筒内侧摩阻力先增大后减小;水平荷载和弯矩作用下,筒侧被动土压力的降低是引起软土覆盖地基中基础承载能力降低的主要因素。 相似文献
18.
19.
Existing tripod suction bucket foundations, utilised for offshore wind turbines, are required to resist significant lateral loads and overturning moments generated by wind and currents. This paper presents an innovative type of tripod bucket foundation, ‘hybrid tripod bucket foundation’, for foundations of offshore wind turbines, which has the ability to provide a larger overturning capacity compared with conventional tripod buckets. The proposed foundation consists of a conventional tripod bucket combined with three large circular mats attached to each bucket. A series of experiments were conducted on small-scale models of the proposed foundation subjected to overturning moment under 1g conditions in loose sand. Different circular mat diameter sizes with various bucket spacings were considered and the results were compared with conventional tripod bucket foundation. Finite element models of the proposed foundation were developed and validated using experimental results and were used to conduct a parametric study to understand the behaviour of the hybrid tripod bucket foundation. The results showed that there is a significant increase in overturning capacity provided by the novel foundation. The results of this work can significantly improve lowering the costs associated with installation of foundations to support offshore wind turbines. 相似文献
20.
筒型基础安装过程中，筒内的负压作用会导致土塞现象的出现。以试验模型为基础建立可变形离散元计算模型，通过VC＋＋编制的程序SPSAⅡ对筒型基础负压沉贯中土塞的生成过程进行可视化模拟计算。考虑渗流力、筒壁内外摩擦阻力和筒内负压吸力作为土塞产生的主要外荷载，分别模拟渤海地区3种典型土（黏土、粉土和砂土）的情况。其中，粉土情况下。程序的收敛速度最快，黏土情况下，土塞的计算高度最接近试验测量值，数值计算结果表明该计算方法作为筒型基础施工前筒内土塞高度的预测方法是可行的。 相似文献