首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
A Sample-Freezing Drive Shoe for a Wire Line Piston Core Sampler   总被引：2，自引：0，他引：2  
Loss of fluids and samples during retrieval of cores of saturated, noncohesive sediments results in incorrect measures of fluid distributions and an inaccurate measure of the stratigraphic position of the sample. To reduce these errors, we developed a hollow drive shoe that freezes in place the lowest 3 inches (75 mm) of a 1.88-inch-diameter (48 mm), 5-foot-long (1.5 m) sediment sample taken using a commercial wire line piston core smapler. The end of the core is frozen by piping liquid carbon dioxide at ambient temperature through a steel tube from a bottle at the land surface to the drive shoe where it evaporates and expands, cooling the interior surface of the shoe to about - 109°F (- 78°C). Freezing a core end takes about 10 minutes. The device was used to collect samples for a study of oil-water-air distributions, and for studies of water chemistry and microbial activity in unconsolidated sediments at the site of an oil spill near Bemidji, Minnesota. Before freezing was employed, samples of sandy sediments from near the water table sometimes flowed out of the core barrel as the sampler was withdrawn. Freezing the bottom of the core allowed for the retention of all material that entered the core barrel and lessened the redistribution of fluids within the core. The device is useful in the unsaturated and shallow saturated zones, but does not freeze cores well at depths greater than about 20 feet (6 m) below water, possibly because the feed tube plugs with dry ice with increased exhaust back-pressure, or because sediment enters the annulus between the core barrel and the core barrel liner and blocks the exhaust.  相似文献   

2.
A coring device has been developed to obtain long and minimally disturbed samples of saturated cohesionless sand and gravel. The coring device, which includes a wireline and piston, was developed specifically for use during hollow-stem auger drilling but it also offers possibilities for cable tool and rotary drilling. The core barrel consists of an inner liner made of inexpensive aluminum or plastic tubing, a piston for core recovery, and an exterior steel housing that protects the liner when the core barrel is driven into the aquifer. The core barrel, which is approximately 1.6m (5.6 feet) long, is advanced ahead of the lead auger by hammering at the surface on drill rods that are attached to the core barrel. After the sampler has been driven 1.5m (5 feet), the drill rods are detached and a wireline is used to hoist the core barrel, with the sample contained in the aluminum or plastic liner, to the surface. A vacuum developed by the piston during the coring operation provides good recovery of both the sediment and aquifer fluids contained in the sediment. In the field the sample tubes can be easily split along their length for on-site inspection or they can be capped with the pore water fluids inside and transported to the laboratory. The cores are 5cm (2 inches) in diameter by 1.5m (5 feet) long. Core acquisition to depths of 35m (115 feet), with a recovery greater than 90 percent, has become routine in University of Waterloo aquifer studies. A large diameter (12.7cm [5 inch]) version has also been used successfully. Nearly continuous sample sequences from sand and gravel aquifers have been obtained for studies of sedimentology, hydraulic conductivity, hydrogeochemistry and microbiology.  相似文献   

3.
An impact drive point method is described for emplacing piezometers in a cobble river bottom where this has previously been difficult without the use of drilling rigs. To force the drive point piezometers through coble, the vibrational impact of an air-powered hammer was carried directly to the drive point by the use of an internal drive rod. After insertion to depth, the drive rod was removed from the lower portion of the piezometer and a standpipe was added to extend the piezometer above the river level. Piezometers installed in this way have permitted water quality analysis and dynamic measurement of vertical potentials in cobble sediments ranging in size from 2.5 to >30 cm and the method has been successfully used in the Columbia River, USA, and Töss River, Switzerland. This innovative method provides information on the hydrodynamics of pore water in highly permeable, cobble deposits that are common in high-energy river and lake bottoms. Piezometers installed using the internal drive rod method facilitate the assessment of the temporal and spatial dynamics of recharge and discharge at the ground water/surface water interface and analyses of the ecological connectivity between the hyporheic zone and surface water of rivers and streams. This information will lead to improved management decisions related to our nation's ground water and surface water supplies.  相似文献   

4.
Water and gas samples were collected from (1) nine shallow groundwater aquifers overlying Marcellus Shale in north‐central West Virginia before active shale gas drilling, (2) wells producing gas from Upper Devonian sands and Middle Devonian Marcellus Shale in southwestern Pennsylvania, (3) coal‐mine water discharges in southwestern Pennsylvania, and (4) streams in southwestern Pennsylvania and north‐central West Virginia. Our preliminary results demonstrate that the oxygen and hydrogen isotope composition of water, carbon isotope composition of dissolved inorganic carbon, and carbon and hydrogen isotope compositions of methane in Upper Devonian sands and Marcellus Shale are very different compared with shallow groundwater aquifers, coal‐mine waters, and stream waters of the region. Therefore, spatiotemporal stable isotope monitoring of the different sources of water before, during, and after hydraulic fracturing can be used to identify migrations of fluids and gas from deep formations that are coincident with shale gas drilling.  相似文献   

5.
南海北部琼东南海域活动冷泉特征及形成模式   总被引：3，自引：0，他引：3       下载免费PDF全文
近年来,活动冷泉的研究越来越受到关注.本文利用多波束数据、多道地震数据以及底质取样结果研究琼东南海域活动冷泉系统,分析活动冷泉的羽状流特征、海底地貌与底质特征以及流体活动构造特征.多波束水体数据上,观测到多个延伸高度超过750 m的气泡羽状流,海底流体活动非常强烈;多道地震上识别出麻坑、流体运移通道、气烟囱等流体渗漏相关的构造,与其他海域观测到的反射特征不同,羽状流的下方流体运移通道呈强振幅"串珠"反射;重力活塞取样在两个站位上获得浅表层块状天然气水合物.其中一个站位位于活动冷泉附近,天然气水合物赋存于海底以下8 m左右.基于以上三方面的数据,笔者提出了一个用于描述活动冷泉系统的形成模式,游离气通过气烟囱向上运移到达浅层,一部分在天然气水合物稳定带内形成天然气水合物,另一部分穿透天然气水合物稳定带到达海底,形成活动冷泉的羽状流.  相似文献   

6.
The potential association of acid-volatile sulfides (AVS) and reactive (HCl soluble) Fe with the distribution of reactive trace metals (Cu, Cd, Ni, Pb and Zn) was investigated in sediment cores collected in the Igua?u river estuarine system (Guanabara bay, Brazil), within the river (core R) and the bay (core B) areas. Moderate to extremely high AVS concentrations (33-314 micromol g(-1)) were found in the rapidly-accumulated sediments of this eutrophicated estuary. AVS showed significant correlations with Fe, Ni and Pb in core B, whereas no correlation between AVS and metals was observed in core R. Results suggest that the AVS:Fe molar ratio may often reflect the diagenetic conditions controlling the distribution of Cd and Cu in core B better than AVS and Fe levels themselves. A shift in the biogeochemical controls of metal distribution from the river to the open bay sediments is suggested, with a greater association of most metals with AVS and Fe in bay sediments.  相似文献   

7.
Xunhong Chen 《水文研究》2011,25(2):278-287
Characterization of streambed hydraulic conductivity from the channel surface to a great depth below the channel surface can provide needed information for the determination of stream‐aquifer hydrologic connectedness, and it is also important to river restoration. However, knowledge on the streambed hydraulic conductivity for sediments 1 m below the channel surface is scarce. This study describes a method that was used to determine the distribution patterns of streambed hydraulic conductivity for sediments from channel surface to a depth of 15 m below. The method includes Geoprobe's direct‐push techniques and Permeameter tests. Direct‐push techniques were used to generate the electrical conductivity (EC) logs and to collect sequences of continuous sediment cores from river channels, as well as from the alluvial aquifer connected to the river. Permeameter tests on these sediment cores give the profiles of vertical hydraulic conductivity (Kv) of the channel sediments and the aquifer materials. This method was applied to produce Kv profiles for a streambed and an alluvial aquifer in the Platte River Valley of Nebraska, USA. Comparison and statistical analysis of the Kv profiles from the river channel and from the proximate alluvial aquifer indicates a special pattern of Kv in the channel sediments. This depth‐dependent pattern of Kv distribution for the channel sediments is considered to be produced by hyporheic processes. This Kv‐distribution pattern implied that the effect of hyporheic processes on streambed hydraulic conductivity can reach the sediments about 9 m below the channel surface. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

8.
Ji-Hoon  Kim  Myong-Ho  Park  Urumu  Tsunogai  Tae-Jin  Cheong  Byong-Jae  Ryu  Young-Joo  Lee  Hyun-Chul  Han  Jae-Ho  Oh  Ho-Wan  Chang 《Island Arc》2007,16(1):93-104
Abstract Geochemical analyses of sediments, pore water and headspace gas of the piston cores taken from the eastern part of Ulleung Basin of the East Sea (Japan Sea) were carried out to assess the origin of the sedimentary organic matter and interstitial fluid. Several tephra layers within the core are identified as the Ulleung‐Oki (10.1 ka), the Aira‐Tanzawa (23 ka) and the Ulleung‐Yamato (30.9 ka) tephras. With the exception of these volcanic layers, the cores consist predominantly of muddy sediments that contain >0.5% total organic carbon. Atomic C/N ratios and δ13Corg values suggest that the organic matter originated from marine algae rather than from land vascular plants, whereas Rock‐Eval pyrolysis suggests that the organic matter is thermally immature and comes from a land vascular plant (Type III). These conflicting results seem to be caused by the heavy oxidization of the marine organic matter. Sulphate concentration profiles of pore waters show strongly linear depletion (r2 > 0.97) with sediment depth. The estimated sulphate–methane interface (SMI) depth using the sulphate concentration gradient was nearly 3.5 m below seafloor (mbsf) in the southern part of the study area, and deeper than 6 mbsf in the northern part of the area. The difference in SMI depths is likely associated with the amount of the methane flux. The methane concentration below the SMI in the two southern cores increases rapidly, implying the occurrence of methanogenesis and anaerobic methane oxidation (AMO). In contrast, the two northern cores have a low methane concentration below the SMI. values measured from all cores were in the range of −83.5 to −69.5‰, which suggests that the methane derives from a methanogenic microbe. values become decreased toward SMI, but increased below SMI; therefore, has eventually the minimum value near the SMI. The values are also decreased when the methane concentration is increased. These phenomena support the typical occurrence of AMO in the study area.  相似文献   

9.
Enterococci are used to evaluate the safety of beach waters and studies have identified beach sands as a source of these bacteria. In order to study and quantify the release of microbes from beach sediments, flow column systems were built to evaluate flow of pore water out of beach sediments. Results show a peak in enterococci (average of 10% of the total microbes in core) released from the sand core within one pore water volume followed by a marked decline to below detection. These results indicate that few enterococci are easily removed and that factors other than simple pore water flow control the release of the majority of enterococci within beach sediments. A significantly larger quantity and release of enterococci were observed in cores collected after a significant rain event suggesting the influx of fresh water can alter the release pattern as compared to cores with no antecedent rainfall.  相似文献   

10.
This paper describes a drive point system for installing small‐diameter (15 to 25 mm ID) piezometers to depths of several metres in unconsolidated sediments. The system fills the gap between (1) heavy duty drive point systems powered by drilling rig hydraulics or air hammers that are capable of installing large diameter drive points to depths of many tens of metres and (2) manually driven systems that typically install 10 mm ID or smaller tubing to depths of <2 m. Unlike many existing systems, which install piezometers inside an outer casing that is later removed, our system protects the piezometer screen inside the casing and extends it only once the casing is driven to the desired depth. This avoids clogging of the screen during installation and the risk of creating an annulus around the piezometer, which can provide a preferential pathway for water movement. The piezometer has a larger diameter than most manually driven systems, and thus has a higher yield; it also permits use of most commercially available pressure transducers and electrical conductivity sensors. The piezometers have been successfully installed to depths of up to 6 m using an electric hammer. The system overcomes some issues associated with existing systems and provides the advantages of affordability, rapid installation, mechanical assistance and manual portability.  相似文献   

11.
A boring instrument for the removal of undisturbed samples from lake sediments at any depth is described. The bore tube cuts a sediment core (diameter 110 mm) in which the layering structure of a 300 mm long section can be examined in its natural undisturbed form. The core is sectioned using a knife made out of mineral glass (thin window glass). The core can be fixed with a piston and laid down horizontally. After removing the glass knife, it can be further processed, sampled, etc. Examples of such cores from the Greifensee, the Hallwilersee and from Lake Lucerne (Bay of Gersau) show the amazing detail and individuality of the sediments.  相似文献   

12.
1 INTRODUCTION Lake Calumet is located 15 miles southeast of downtown Chicago. The geographical boundaries include 130th Street to the south, Stony Island Avenue to the east, an industrial area to the north, and interstate highway I-94 to the west. The major continuous water inflow to the lake is Pullman Creek, a drainage ditch, which carries the runoff from the nearby expressway, industries, and landfills into the lake at the northwest corner. The outlet of the Lake is the Calumet R…  相似文献   

13.
Spatial and temporal heterogeneity of recent diatom stratigraphy were assessed for a small (23 ha) dimictic lake in Northern Sweden (Kassjön). Varves are confined to water depths > 10 m. Six freeze cores were taken along a transect covering a range of water depths (3–12 m) and both varved and non-varved sediments. Core profiles were compared for dry mass accumulation, loss-on-ignition (LOI), and diatom relative frequency stratigraphy and accumulation rate. Excluding the 3.2 m water depth, non-varved core, all parameters showed good repeatability between cores, apart from diatom accumulation rates which were more variable. The 3.2 m core was atypical and had lower LOI values, low planktonic diatom percentages and high values of benthic taxa that were not abundant in the deep-water sediments. Detrended Correspondence Analysis (DCA) and Canonical Correspondence Analysis (CCA) ordinations were compared; both methods clearly differentiated the shallow water core, and showed the general similar ecological trends of the deeper-water cores. CCA axes constrained by environmental (i. e. core location) data resulted in slightly lower eigenvalues than that obtained by Correspondence Analysis (CA), but the axes were significantly non-random. A Partial-CCA of the four varved cores alone (with effects of sediment depth, i.e. age, partialled out), indicated that there was no significant difference between their diatom assemblages.  相似文献   

14.
Two sediment cores (Southern Branch, PC-1, and Western Branch, WB-2) were taken from the highly industrialized Elizabeth River, Virginia. The concentrations of trace metals cadmium, cobalt, chromium, copper, nickel, lead and zinc, major elements iron, manganese and aluminum, organic carbon content and the specific surface area of the sediments were determined in each of the cores. Down-core variations in metals varied significantly in each core with maximum contamination events occurring at different times in different portions of the river. In PC-1, maximum metal concentrations were seen after the appearance of (137)Cs. In contrast, the highest levels in WB-2 occurred well before the appearance of (137)Cs. Although stricter environmental regulations have caused a decrease in metal concentrations since the 1980s, the concentrations in the surface sediments of many trace metals were elevated to levels 2-5 times higher than the levels at the bottom of the cores in both the Southern and Western Branches of the river.  相似文献   

15.
We examined the influence of river stage on subsurface hydrology and pore water chemistry within the hyporheic zone of a groundwater‐fed river during the summer baseflow period of 2011. We found river stage and geomorphologic environment to control chemical patterns in the hyporheic zone. At a high river stage, the flux of upwelling water in the shallow sediments (>20 cm) decreased at sample sites in the upper section of our study reach and increased substantially at sites in the lower section. This differential response is attributed to the contrasting geomorphology of these subreaches that affects the rate of the rise and fall of a river stage relative to the subsurface head. At sites where streamward vertical flux decreased, concentration profiles of a conservative environmental tracer suggest surface water infiltration into the riverbed below depths recorded at a low river stage. An increase in vertical flux at sites in the lower subreach is attributed to the movement of lateral subsurface waters originating from the adjacent floodplain. This lateral‐moving water preserved or decreased the vertical extent of the hyporheic mixing zone observed at a low river stage. Downwelling surface water appeared to be responsible for elevated dissolved organic carbon (DOC) and manganese (Mn) concentrations in shallow sediments (0–20 cm); however, lateral subsurface flows were probably important for elevated concentrations of these solutes at deeper levels. Results suggest that DOC delivered to hyporheic sediments during a high river stage from surface water and lateral subsurface sources could enhance heterotrophic microbial activities. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

16.
南海北部神狐海域天然气水合物分解的测井异常   总被引：2，自引：0，他引：2       下载免费PDF全文
南海北部神狐海域GMGS-1钻探揭示SH3井天然气水合物位于稳定带上部,厚度约为10 m.氯离子异常计算的水合物饱和度最高达26%,高水合物饱和度层出现高电阻率和低纵波速度.为分析该低纵波速度异常,本文基于简化的三相介质理论计算了饱和水纵波速度,在深度195 m附近,测量的纵波速度小于饱和水纵波速度.利用阿尔奇公式,基于原位温度、盐度、密度孔隙度和测量的电阻率,利用交会分析确定了该井的阿尔奇常数为a=1.1和m=2.3.基于该参数,利用阿尔奇方程计算的水合物饱和度占孔隙空间5%~20%,局部地层水合物饱和度达26.8%,在垂向上分布不均匀.由于钻探可能导致水合物发生分解而产生游离气,原位游离气和水合物分解产生的气体都能造成低纵波速度异常.由于地震资料采集在测井之前完成,利用不同速度制作合成地震记录并与地震资料进行对比,能够确定水合物稳定带上部的低速异常形成原因.  相似文献   

17.
Hydrate Ridge is located at the second accretion-ary ridge along the Cascadia margin of Oregon in the eastern North Pacific (fig. 1). The Bottom Simulating Reflector (BSR) underlies the entire Hydrate Ridge[1]. The Ocean Drilling Program (ODP) in 1992 at Site 892 and the TECFLUX99 and 2000 showed that the gas hydrate occurs just beneath the thin sediment- covered surface and at the horizon of around 64 meter below seafloor (mbsf) on Hydrate Ridge[25]. The col-lision of the Juan de …  相似文献   

18.
We present an equilibrium model of methane venting through the hydrate stability zone at southern Hydrate Ridge, offshore Oregon. Free gas supplied from below forms hydrate, depletes water, and elevates salinity until pore water is too saline for further hydrate formation. This system self-generates local three-phase equilibrium and allows free gas migration to the seafloor. Log and core data from Ocean Drilling Program (ODP) Site 1249 show that from the seafloor to 50 m below seafloor (mbsf), pore water salinity is elevated to the point where liquid water, hydrate and free gas coexist. The elevated pore water salinity provides a mechanism for vertical migration of free gas through the regional hydrate stability zone (RHSZ). This process may drive gas venting through hydrate stability zones around the world. Significant amount of gaseous methane can bypass the RHSZ by shifting local thermodynamic conditions.  相似文献   

19.
A secular variation record of the geomagnetic declination has been obtained from glaciolacustrine varved clays and postglacial sediments, sampled both from outcrop and from piston cores from Lake Ontario. It appears to be uninterrupted and covers the interval 14,000 years B.P. (14C) to the present. The record for the interval 14,000–12,300 years B.P. consists of true declination and was obtained from samples collected from outcrop. The record for the interval 12,500 + years B.P. to the present consists of relative declination and was obtained from piston cores. The secular variation record is internally consistent and is compatible with the chronology of events known to have occurred during and following the deglaciation of western New York. Use of the record for magnetic correlation within the study area is demonstrated.  相似文献   

20.
Surface and gravity-cored sediments were collected from the Kaoping coastal area off southwestern Taiwan to determine particle size, organic carbon, trace metal concentration and enrichment factor (EF), 210Pb dating, and 206Pb/207Pb ratio for determining present and historical metal pollution. Surface distributions of trace metals ranged from 0.02 to 0.13 mg/kg for Cd (EF: 0.16-1.65), from 35 to 189 mg/kg for Cr (EF: 0.85-2.92), from 25 to 64 mg/kg for Ni (EF: 0.53-2.38), from 10 to 32 mg/kg for Pb (EF: 1.20-4.94), and from 29 to 129 mg/kg for Zn (EF: 1.18-3.50). Trace metal concentrations correlate closely with distributions of mud (<63 microm) and organic carbon which accumulate largely around river mouths and within the Kaoping Canyon. With the exception of Cd, Cr and Ni in certain areas with rather coarse sediments, metals were generally elevated above the baseline levels over the studied area. Metals were also relatively enriched in areas with high contents of mud and organic carbon. Sedimentation rates derived from the excess 210Pb data in core sediments sampled from the canyon illustrate metal pollution beginning around 1970 that is corresponding to the booming time of economic growth in Taiwan. Meanwhile, the status of Pb pollution in core sediments is verified by an inversed correlation between 206Pb/207Pb ratios and Pb concentrations. Anthropogenic Pb and other metals in the studied area were apparently derived primarily from the Kaoping River and accumulated around the river mouth and within the Kaoping Canyon. The Kaoping Canyon appears to act as a major sink for river borne trace metals.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号