共查询到20条相似文献，搜索用时 31 毫秒
1.
The present paper is Part III of a series of three papers on the methods useful for ultimate limit state assessment of ships and ship-shaped offshore structures. It is focused on the methods for the progressive collapse analysis of hull girders under bending moments, in contrast to the previous two papers (Parts I and II), respectively, dealing with methods for the ultimate limit state assessment of unstiffened plates and stiffened panels. An AFRAMAX-class hypothetical double hull oil tanker structure designed by IACS common structural rules (CSR) method is studied as an illustrative example. The ultimate vertical bending moment capacity of the hull structure is then analyzed by ANSYS FEA, ALPS/HULL, and IACS CSR methods, and their resulting computations are compared. 相似文献
2.
The present paper is Part I of a series of three papers prepared by the authors on the methods useful for ultimate limit state assessment of marine structures, that have been developed in the literature during the last few decades. It is considered that such methods are now mature enough to enter day-by-day design and strength assessment practice. The aims of the three papers are to conduct some benchmark studies of such methods on ultimate limit state assessment of (unstiffened) plates, stiffened panels, and hull girders of ships and ship-shaped offshore structures, using some candidate methods such as ANSYS nonlinear finite element analysis (FEA), DNV PULS, ALPS/ULSAP, ALPS/HULL, and IACS common structural rules (CSR) methods. As an illustrative example, an AFRAMAX-class hypothetical double hull oil tanker structure designed by CSR method is studied. In the present paper (Part I), the ultimate limit state assessment of unstiffened plates under combined biaxial compression and lateral pressure loads is emphasized using ANSYS, DNV PULS, and ALPS/ULSAP methods, and their resulting computations are compared. Part II will deal with methods for the ultimate limit state assessment of stiffened panels under combined biaxial compression and lateral pressure using ANSYS, DNV PULS, and ALPS/ULSAP methods, and Part III will treat methods for the progressive collapse analysis of the hull structure using ANSYS, ALPS/HULL, and IACS CSR methods. 相似文献
3.
《中国海洋工程》2020,(4)
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression. Both material and geometric non-linearities were considered in finite element(FE) analysis. The initial geometric imperfection of the plate was considered, while the residual stress introduced by welding was not considered. The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions, initial imperfection and mesh size. The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented. Then a new simple empirical formula for plate ultimate strength is developed, which includes the effect of the rotational restraint stiffness, rotational restraint stiffness, and aspect ratios. By applying the new formula and FE method to ship hull plates in real ships, a good coincidence of the results between these two methods is obtained, which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges. 相似文献
4.
Jeom Kee Paik 《Ocean Engineering》2009,36(3-4):266-276
The main objective of the present paper is to numerically examine the residual ultimate strength characteristics of steel plates with longitudinal cracks under axial compressive actions. The present paper is a sequel to the author's previous paper [Paik, J.K., 2008. Residual ultimate strength of steel plates with longitudinal cracks under axial compression—Experiments. Ocean Engineering 35, 1775–1783]. In contrast to the previous paper, the present paper deals with nonlinear finite element method investigations. Because the test programme is usually limited to a few test models in number for many reasons, the application of nonlinear finite element methods is often more beneficial to handle a more variety of parameters of influence. In the present paper, the insights developed from a series of ANSYS nonlinear finite element method computations are documented, where the effects of the crack orientation, the crack location, the crack size, the plate thickness, and the plate aspect ratio on the residual ultimate strength of steel plates with longitudinal cracks under axial compression are discussed. The insights developed from the present work will be useful for cracking damage-tolerant design of steel-plated structures and also for health monitoring or condition assessment of aging steel-plated structures with cracking damages. 相似文献
5.
Corrosion and fatigue cracks are major threats to the structural integrity of aging offshore platforms.For the rational estimation of the safety levels of aging platforms,a global reliability assessment approach for aging offshore platforms with corrosion and fatigue cracks is presented in this paper.The base shear capacity is taken as the global ultimate strength of the offshore plaffoms,it is modeled as a random process that decreases with time in the presence of corrosion and fatigue crack propagation.And the corrosion and fatigue crack growth rates in the main members and key joints are modeled as random variables.A simulation method of the extreme wave loads which are applied to the structures of offshore platforms is proposed too.Furthermore,the statistics of global base shear capacity and extreme wave loads are obtained by Monte Carlo simulation method.On the basis of the limit state equation of global failure mode,the instantaneous reliability and time dependent reliability assessment methods are both presented in this paper.Finally the instantaueous reliability index and time dependent failure probability of a jacket platform are estimated with different ages in the demonstration example. 相似文献
6.
Artificial neural networks and their application to assessment of ultimate strength of plates with pitting corrosion 总被引：1，自引：0，他引：1
The potential for the structural capability degrading effects of both corrosion and fatigue induced cracks are of profound importance and must be both fully understood and reflected in vessel's inspection and maintenance programme. Corrosion has been studied and quantified by many researchers, however its effect on structural integrity is still subject to uncertainty, particularly with regards to localized corrosion. The present study is focused on assessing the effects of localized pitting corrosion on the ultimate strength of unstiffened plates. Over 265 non-linear finite-element analyses of panels with various locations and sizes of pitting corrosion have been carried out. The results indicate that the length, breadth and depth of pit corrosion have weakening effects on the ultimate strength of the plates while plate slenderness has only marginal effect on strength reduction. Transverse location of pit corrosion is also an important factor determining the amount of strength reduction. When corrosion spreads transversely on both edges, it has the most deteriorating effect on strength. In addition, artificial neural network (ANN) method is applied to derive a formula to predict ultimate strength reduction of locally corroded plates. It is found out that the proposed formulae can accurately predict the ultimate strength of locally corroded plates under uniaxial in-plane compression. 相似文献
7.
导管架式海洋平台结构极限承载力分析的整体推进法及其软件 总被引：9，自引：1，他引：8
根据非线性有限元逐步分析的思想,以已有的结构弹性分析软件为计算核心,提出了一种近似分析结构极限承载力的方法——整体推进法;采用整体推进法,以导管架式海洋平台结构线弹性分析软件ＥＮＳＡ为计算核心,考虑结构构件的损伤影响和维修加固效果,编制了导管架式海洋平台结构极限承载力近似分析软件ＵＡＰ,为导管架式海洋平台结构的安全度评定提供了方法和手段;最后对渤海八号生产／储油平台在１９９３年的状态和ＪＺ２０２ＭＵＱ平台的完好状态进行了极限承载力分析 相似文献
8.
为了快速并有效地计算海洋平台等薄壁箱型梁结构的约束扭转极限承载能力,进行了薄壁梁约束扭转极限承载能力简化计算方法研究.基于塑性极限状态分析理论,提出了薄壁梁约束扭转极限状态应力分布假设,将薄壁梁视作为一系列由主要支撑构件和扶强材支撑的板格,推导了薄壁梁约束扭转极限承载能力上限的计算公式.应用非线性有限元方法验证了所提假设和计算公式的精度,将所提方法应用于箱型梁模型和半潜平台的约束扭转极限承载能力的计算分析,并与非线性有限元结果进行了比对,结果表明,本方法具有较高的精度,可用于海洋平台等薄壁梁的扭转极限承载力上限的估算. 相似文献
9.
船舶与海洋结构在服役期间会遭受电化学和微生物侵蚀等多种腐蚀环境影响,加筋板作为此类结构的主要受力构件,其表面易产生不规则形态的点蚀,引起构件的强度退化。利用ANSYS有限元软件构建加筋腹板遭受随机点蚀损伤的加筋板有限元模型,研究带板长宽比、带板长细比、加筋长细比和腐蚀体积损失率对加筋板极限强度的影响。研究结果表明,加筋遭受同等腐蚀体积损失率下,带板长宽比变化对极限强度退化的影响很小,但带板长细比和加筋长细比变化产生的影响明显;带板长细比越大,极限强度退化越严重,而加筋长细比越大,极限强度退化反而越小。针对文中研究的加筋板,当加筋长细比为 0.2时,腐蚀体积率为14%的随机点蚀导致结构极限强度退化程度达到约14.0%。因此,加筋的随机点蚀损伤会显著削弱加筋板结构的极限强度,其影响不可忽略。 相似文献
10.
The elastic-plastic method is often used in designing the inner flat bulkhead plates of submarines, and the upper structure of ships and drilling platforms. Such bulkhead plates can bear the load only once. For the improvement of the load-carrying capacity or the reduction of the weight of plates, the yield line analytical method is employed in this paper to design the bulkhead plate to improve economy and increase the effiective load. Besides, a further sutdy of this method has been made theoretically and experimentally, and the data of the limited load-carrying capacity of the plate have been obtained. Furthermore, the safety coefficients for such a method are presented, which can be used as reference for related departments and staffs. 相似文献
11.
The main objective of the present study is to examine the residual ultimate strength characteristics of steel plates with cracking damages under axial compressive actions through experimental investigations. The present study is a sequel of the author's previous paper (Paik, J.K., Satish Kumar, Y.V., Lee, J.M., 2005. Ultimate strength of cracked plate elements under axial compression or tension. Thin-Walled Structures, 43, 237–272). In contrast to the previous paper which dealt with transverse cracks located in the direction normal to the axial loading direction, the present paper is concerned with longitudinal cracks which are located in parallel to the axial loading direction. Similar to the previous paper, the orientation/location and size of cracks inside the plates are varied for the present experimental investigations. The details of experimental results are documented. The database and insights developed from the present work will be useful for cracking damage-tolerant design of steel-plated structures and also for condition assessment or health monitoring of aging steel-plated structures. 相似文献
12.
Determining the ultimate capacity of suction caissons in response to combined vertical, horizontal, and moment loading is essential for their design as foundations for offshore wind turbines. However, the method implemented for stability analysis is quite limited. Numerical limit analysis has an advantage over traditional limit equilibrium methods and nonlinear finite element methods in this case because upper and lower bounds can be achieved to ensure that the exact ultimate capacity of the caisson falls within the appropriate range. This article presents theories related to numerical limit analysis. Simulations are conducted for centrifuge model tests, the findings of which reveal the ability of numerical limit analysis to deal with the inclined pullout capacity of suction caissons. Finally, this article proposes an estimation of the ultimate capacity of a 3.5 MW offshore wind turbine foundation on normally consolidated clay based on the typical environmental parameters of Bothkennar, Scotland. Undrained failure envelopes and safety factors are obtained for suction caissons with different embedment ratios. Failure mechanisms, plastic zones, clay stress distributions, and the influence of the skin friction coefficients of caissons are discussed in detail. 相似文献
13.
《Applied Ocean Research》2007,29(1-2):17-36
Finite-memory nonlinear systems (FMNS) are extensively used in establishing a simple relationship between the output and input of complicated nonlinear systems. In Part I of this paper, it was shown how the response of an offshore structure exposed to (random) Morison wave loading can be approximated by the response of an equivalent finite-memory nonlinear system. The approximate FMNS models can then be used to determine, with great efficiency, the probability distribution of response extreme values. Part I of this paper was devoted to the development of FMNS models for offshore structural response. In this part, the validity of the developed models has been investigated by examining the response of three test structures under different environmental conditions. The results are promising. 相似文献
14.
The existence of the heaving plates can improve the heaving motion performance of an offshore structure significantly by providing both extra added mass and damping. In the current research, numerical investigation is carried out on the hydrodynamic characteristics of both isolated square heaving plate and double square heaving plates with opening by an immersed boundary-lattice Boltzmann method. The effects on hydrodynamic performance of plates due to Keulegan-Carpenter(KC) number, frequency number, opening ratio, opening distribution and spacing of plates are examined. It is found that the heaving plates with optimized opening ratio can provide additional damping compared with the plates without opening. Better hydrodynamic characteristics of double plates can be obtained with the increase of plate spacing. 相似文献
15.
《Applied Ocean Research》2007,29(1-2):1-16
Offshore structures are exposed to random wave loading in the ocean environment and hence the probability distribution of the extreme values of their response to wave loading is of great value in the design of these structures. Wave loading on slender members of bottom-supported jacket or jack-up structures is frequently calculated by Morison’s equation. Due to nonlinearity of the drag component of Morison wave loading and also due to intermittency of wave loading on members in the splash zone, the response is often non-Gaussian; therefore, simple techniques for derivation of their extreme response probability distribution are not available. Finite-memory nonlinear systems (FMNS) are extensively used in establishing a simple relationship between the output and input of complicated nonlinear systems. In this paper, it will be shown how the response of an offshore structure exposed to Morison wave loading can be approximated by the response of an equivalent finite-memory nonlinear system. The approximate models can then be used to determine the probability distribution of response extreme values with great efficiency. Part I of this paper is devoted to the development of an efficient FMNS model for offshore structural response while part II is devoted to the validation of the developed models. 相似文献
16.
为了拓展主S-N曲线法,使之更好地适用于低温、极地环境下船舶与海洋工程结构物的疲劳评估,进行了EH36材料T型焊接接头的低温疲劳性能试验,收集了国内外多个焊接节点低温疲劳数据,建立了疲劳试验试件的有限元模型,运用等效结构应力法,计算焊接节点的等效结构应力,构建低温环境下焊接节点的主S-N曲线。使用该曲线,预测低温疲劳试验的寿命,并与疲劳试验结果、常温主S-N曲线、常温中值D曲线的预测结果进行了比较,结果表明,所提低温主S-N曲线预测方法具有较高精度,可用于低温环境下船舶与海洋结构物疲劳寿命的预测。 相似文献
17.
在环境条件和使用荷载作用下,高桩码头结构损伤和承载力降低是普遍存在的问题。在役梁板式高桩码头结构安全评估,是保证港口设施安全运行的必要措施。结构整体可靠度是结构安全评估的核心指标,但目前尚未建立结构整体可靠度计算的有效方法。基于非线性有限元数值模型,采用蒙特卡罗模拟技术确定了典型梁板式高桩码头结构整体极限承载力概率分布模型及其统计参数,研究了损伤位置、损伤程度和损伤数量等对极限承载力概率分布及其统计参数的影响,明确了无损结构整体极限承载力概率分布模型及其统计参数可用于损伤结构分析。将结构整体极限承载力作为结构抗力随机变量,采用一次二阶矩法计算结构的可靠指标,建立了一种在役梁板式高桩码头结构整体可靠度计算的有效方法。 相似文献
18.
为改善海上风电大直径钢管桩的水平承载性能,基于ABAQUS有限元软件对单桩改进形式的加翼桩结构进行了系统研究,计算分析了软黏土地基中加翼桩在水平荷载作用下桩身弯矩、应力、位移、桩身泥面处倾斜率和极限承载力,研究了加翼桩面积、形状、埋深和刚度等翼板参数对加翼桩水平承载性能的影响规律,根据加翼桩的桩-土作用机理,参考现行规范模式提出适用于软黏土地基大直径钢管桩的P-Y曲线。研究结果表明,加翼桩通过在泥面处设置翼板可降低桩基泥面处倾斜率50%、提高桩基极限承载力60%以上,加翼桩水平承载性能明显优于单桩。 相似文献
19.
20.
海洋平台结构抗震可靠性时程分析方法 总被引：3，自引：0，他引：3
将地震运动视为随机过程,建立海洋平台结构在地震作用任一时刻基于剪切变形控制的极限状态方程,应用JC法计算海洋平台结构在地震作用任一时刻的可靠度,得到海洋平台结构抗震可靠度的时程曲线。该方法可满足工程设计的要求,便于工程应用。 相似文献