共查询到20条相似文献，搜索用时 46 毫秒
1.
The shear modulus at very small strains (less than 0.001%) is an important parameter in the design of geotechnical structures subjected to static and cyclic loadings. Although numerous soil models are available for predicting shear modulus of saturated and dry soils, only a few ones can predict shear stiffness at very small strains of unsaturated soils correctly. In this study, a few unsaturated soil models are evaluated critically and compared with a newly developed model. This newly proposed model is verified by using measured shear modulus at very small strains for three different low plasticity fine grained soils available in the literature. It is found that this new model can predict shear modulus at very small strain resulting from an increase and a decrease in mean net stress at constant matric suction for low plasticity fine grained soils. Moreover, this model is able to give a reasonably good prediction on shear stiffness at very small strain during wetting of a collapsible unsaturated soil. In addition, the newly proposed model is illustrated to capture a consistent trend with experimental data of shear stiffness at very small strain for non-collapsible soils obtained during drying–wetting cycles. This evaluation revealed that the newly proposed model has better predictive capabilities than some earlier formulations of the same simplicity. In addition, the proposed model with fewer parameters has similar predictive capability as compared with a more complex model. 相似文献
2.
The paper presents a mechanical model for non‐isothermal behaviour of unsaturated soils. The model is based on an incrementally non‐linear hypoplastic model for saturated clays and can therefore tackle the non‐linear behaviour of overconsolidated soils. A hypoplastic model for non‐isothermal behaviour of saturated soils was developed and combined with the existing hypoplastic model for unsaturated soils based on the effective stress principle. Features of the soil behaviour that are included into the model, and those that are not, are clearly distinguished. The number of model parameters is kept to a minimum, and they all have a clear physical interpretation, to facilitate the model usefulness for practical applications. The step‐by‐step procedure used for the parameter calibration is described. The model is finally evaluated using a comprehensive set of experimental data for the thermo‐mechanical behaviour of an unsaturated compacted silt. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
3.
An unsaturated soil is a state of the soil. All soils can be partially saturated with water. Therefore, constitutive models for soils should ideally represent the soil behaviour over entire ranges of possible pore pressure and stress values and allow arbitrary stress and hydraulic paths within these ranges. The last two decades or so have seen significant advances in modelling unsaturated soil behaviour. This paper presents a review of constitutive models for unsaturated soils. In particular, it focuses on the fundamental principles that govern the volume change, shear strength, yield stress, water retention and hydro-mechanical coupling. Alternative forms of these principles are critically examined in terms of their predictive capacity for experimental data, the consistency between these principles and the continuity between saturated and unsaturated states. 相似文献
4.
The Barcelona basic model cannot predict the mechanical behaviour of unsaturated expansive soils, whereas the Barcelona expansive model (BExM) can only predict the stress–strain behaviour of unsaturated expansive soils without the water‐retention behaviour being incorporated. Moreover, the micro‐parameters and the coupling function between micro‐structural and macro‐structural strains in the BExM are difficult to determine. Experimental data show that the compression curves for non‐expansive soils under constant suctions are shifted towards higher void ratios with increasing suction, whereas the opposite is true for expansive soils. According to the observed water‐retention behaviour of unsaturated expansive soils, the air‐entry value increases with density, and the relationship between the degree of saturation and void ratio is linear at constant suction. According to the above observation, an elastoplastic constitutive model is developed for predicting the hydraulic and mechanical behaviour of unsaturated expansive soils, based on the existing hydro‐mechanical model for non‐expansive unsaturated soil. The model takes into consideration the effect of degree of saturation on the mechanical behaviour and that of void ratio on the water‐retention behaviour. The concept of equivalent void ratio curve is introduced to distinguish the plastic potential curve from the yield curve. The model predictions are compared with the test results of an unsaturated expansive soil, including swelling tests under constant net stress, isotropic compression tests and triaxial shear tests under constant suction. The comparison indicates that the model offers great potential for quantitatively predicting the hydraulic and mechanical behaviour of unsaturated expansive soils. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
5.
This study presents a simple approach to modelling the effect of temperature on the deformation and strength of unsaturated/saturated soils by using the average skeleton stress and degree of saturation. The concept of thermo-induced equivalent stress is introduced to consider the influence of temperature on the pre-consolidated stress. A skeleton stress–saturation framework is applied to enable the model to describe the thermo-elastoplastic behaviour of both unsaturated and saturated soils, as the skeleton stress can smoothly shift to Terzaghi’s effective stress if saturation changes from the unsaturated to the saturated condition. The new model only employs seven parameters, of which five parameters are the same as those used in the Cam-Clay model. The other two parameters can be easily determined by oedometer tests and simple thermo-mechanical tests. Numerical simulations of isotropic loading tests and triaxial shear tests under different conditions are conducted to illustrate the performance of the proposed model. By comparing with experimental temperature controlled oedometer tests and triaxial tests, it is confirmed that the proposed model is able to capture the thermo-mechanical behaviour of unsaturated/saturated normally and over-consolidated soils with a set of unified parameters. 相似文献
6.
7.
Matthieu Dumont Said Taibi Jean‐Marie Fleureau Nabil Abou‐Bekr Abdelghani Saouab 《国际地质力学数值与分析法杂志》2011,35(12):1299-1317
A simple thermo‐hydro‐mechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
8.
David Mašín 《国际地质力学数值与分析法杂志》2010,34(1):73-90
The paper presents an approach to predicting variation of a degree of saturation in unsaturated soils with void ratio and suction. The approach is based on the effective stress principle for unsaturated soils and several underlying assumptions. It focuses on the main drying and wetting processes and does not incorporate the effects of hydraulic hysteresis. It leads to the dependency of water retention curve (WRC) on void ratio, which does not require any material parameters apart from the parameters specifying WRC for the reference void ratio. Its validity is demonstrated by comparing predictions with the experimental data on four different soils taken over from the literature. Good correlation between the measured and predicted behaviour indirectly supports applicability of the effective stress principle for unsaturated soils. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
9.
Matthieu Dumont Said Taibi Jean-Marie Fleureau Nabil Abou Bekr Abdelghani Saouab 《Comptes Rendus Geoscience》2010,342(12):892-900
A simple thermohydromechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. 相似文献
10.
This paper presents an advanced constitutive model for unsaturated soils, using Bishop’s effective stress (σ′) and the effective degree of saturation (Se) as two fundamental constitutive variables in the proposed constitutive model. A sub-loading surface and a unified hardening parameter (H) are introduced into the σ′–Se modelling framework to interpret the effects of initial density on coupled hydro-mechanical behaviour of compacted soils. Compared with existing models in the literature, the main advantage of the proposed model that it is capable of modelling hydro-mechanical behaviour of unsaturated soils compacted to different initial densities, such as the dependence of loading–collapse volume on initial void ratio and density effect on the shearing-induced saturation change. The proposed model requires 13 material parameters, all of which can be calibrated through conventional laboratory tests. Numerical studies are conducted to assess the performance of the model for a hypothetical soil under two typical hydro-mechanical loading scenarios. The proposed advanced unsaturated soil model is then validated against a number of experimental results for both isotropic and triaxial conditions reported in the literature. 相似文献
11.
For the assessment of shallow landslides triggered by rainfall, the physically based model coupling the infinite slope stability
analysis with the hydrological modeling in nearly saturated soil has commonly been used due to its simplicity. However, in
that model the rainfall infiltration in unsaturated soil could not be reliably simulated because a linear diffusion-type Richards’
equation rather than the complete Richards’ equation was used. In addition, the effect of matric suction on the shear strength
of soil was not actually considered. Therefore, except the shallow landslide in saturated soil due to groundwater table rise,
the shallow landslide induced by the loss in unsaturated shear strength due to the dissipation of matric suction could not
be reliably assessed. In this study, a physically based model capable of assessing shallow landslides in variably saturated
soils is developed by adopting the complete Richards’ equation with the effect of slope angle in the rainfall infiltration
modeling and using the extended Mohr–Coulomb failure criterion to describe the unsaturated shear strength in the soil failure
modeling. The influence of rainfall intensity and duration on shallow landslide is investigated using the developed model.
The result shows that the rainfall intensity and duration seem to have similar influence on shallow landslides respectively
triggered by the increase of positive pore water pressure in saturated soil and induced by the dissipation of matric suction
in unsaturated soil. The rainfall duration threshold decreases with the increase in rainfall intensity, but remains constant
for large rainfall intensity. 相似文献
12.
目前大多数非饱和土的弹塑性本构模型用非饱和击实土的试验结果进行验证,但现场其他类型的土,如沉积土经常有在非饱和状态下外部环境变化的情况。现有的非饱和土弹塑性模型是否适用于沉积土一类的现场土是需要研究的课题。进行非饱和上海第③层土的吸力控制排水排气三轴剪切试验,使用文中提出的能统一考虑非饱和土水力性状和力学性状的弹塑性本构模型,预测上述三轴试验结果,并与试验数据进行比较。比较结果显示,建立的本构模型能够很好地预测非饱和上海软土的水力和力学性质,说明该模型不仅可以适用击实土的预测,还能够很好地适用于其他类型非饱和土的水力和力学性质的模拟。 相似文献
13.
大量的非饱和土干湿循环试验表明,当土体处于吸湿过程直至吸力降低为0 kPa时,土体并不能达到完全饱和状态,还存在一定的残余气体。在高饱和度时,由于残余气体以封闭气泡的形式分布在土体中,土体呈现较大的压缩性,使其与饱和土的性质不同。在这种状态下,现有的非饱和土本构模型预测到的土饱和度为100%,与试验结果存在一定的偏差。为了使本构模型在高饱和度状态时具有较高的精度,对非饱和土的毛细滞回和塑性变形耦合本构模型进行了修正,使其能够考虑残余含气量的影响。通过预测与实测结果比较,证明了新模型能够有效地模拟残余含气量对非饱和土力学特性的影响。 相似文献
14.
In the paper, we present newly developed hydro-mechanical hypoplastic model for partially saturated soils predicting small strain stiffness. Hysteretic void ratio dependent water retention model has been incorporated into the existing hypoplastic model. This required thorough revision of the model structure to allow for the hydro-mechanical coupling dependencies. The model is formulated in terms of degree of saturation, rather than of suction. Subsequently, the small strain stiffness effects were incorporated using the intergranular strain concept modified for unsaturated conditions. New features included degree of saturation-dependent size of the elastic range and an updated evolution equation for the intergranular strain. The model has been evaluated using two comprehensive data sets on completely decomposed tuff from Hong-Kong and Zenos Kaolin from Iran. It has been shown that the modified intergranular strain formulation coupled with the hysteretic water retention model correctly reproduces the effects of both the stress and suction histories on small strain stiffness evolution. The model can correctly predict also different other aspects of partially saturated soil behaviour, starting from the very small strain range up to the asymptotic large-strain response. 相似文献
15.
A hierarchical thermo‐hydro‐plastic constitutive model for unsaturated soils and its numerical implementation 
下载免费PDF全文
下载免费PDF全文 《国际地质力学数值与分析法杂志》2018,42(15):1785-1805
Unsaturated soils are highly heterogeneous 3‐phase porous media. Variations of temperature, the degree of saturation, and density have dramatic impacts on the hydro‐mechanical behavior of unsaturated soils. To model all these features, we present a thermo‐hydro‐plastic model in which the hydro‐mechanical hardening and thermal softening are incorporated in a hierarchical fashion for unsaturated soils. This novel constitutive model can capture heterogeneities in density, suction, the degree of saturation, and temperature. Specifically, this constitutive model has 2 ingredients: (1) it has a “mesoscale” mechanical state variable—porosity and 3 environmental state variables—suction, the degree of saturation, and temperature; (2) both temperature and mechanical effects on water retention properties are taken into account. The return mapping algorithm is applied to implement this model at Gauss point assuming an infinitesimal strain. At each time step, the return mapping is conducted only in principal elastic strain space, assuming no return mapping in suction and temperature. The numerical results obtained by this constitutive model are compared with the experimental results. It shows that the proposed model can simulate the thermo‐hydro‐mechanical behavior of unsaturated soils with satisfaction. We also conduct shear band analysis of an unsaturated soil specimen under plane strain condition to demonstrate the impact of temperature variation on shear banding triggered by initial material heterogeneities. 相似文献
16.
At the present time, it is very common in practice to utilize Mohr-Coulomb model to simulate the soil behaviour in the application of soil-pipeline interaction problems. However, the traditional Mohr-Coulomb model is unable to predict the realistic loading that can apply on buried pipes during large ground deformation. Especially, the linear elastic-perfectly plastic Mohr-Coulomb model is not capable of simulating the unsaturated soil loading which can result larger than anticipated loading due to suction induced additional normal force between the soil particles. A user defined unsaturated modified Mohr-Coulomb model is developed within a generalized effective stress framework considering suction hardening effects to capture the realistic loading induced by unsaturated soil medium. Firstly, the model has been developed considering microscopic and macroscopic suction hardening mechanisms, and was implemented into a commercial finite element program associated with user subroutine written in FORTAN. Then the model was validated through a series of unsaturated triaxial compression tests conducted on the basis of different sand types having various initial conditions. Finally, the model has been applied to simulate the behaviour of pipelines subjected to lateral soil loading in unsaturated soils. The results revealed that the modified Mohr-Coulomb model has reasonable predictions when compared to the load-displacement response of pipes obtained from two large scale testing programs. The developed model can be used to predict the increased strength and stiffness associated with soil suction that increases lateral loads on pipelines, and thus has widespread relevance for simulating the pipeline response in unsaturated soils under externally imposed ground movement. 相似文献
17.
The behaviour of quasi-saturated materials is important to consider when designing cuttings and embankments in which earthwork materials are compacted to the optimum proctor density. Under this condition, the in-pore gaseous phase takes the form of air pockets and bubbles embedded within the liquid phase, which significantly affects the overall behaviour of the soil. The assessment of highly saturated soils thus requires a precise understanding of hydro-chemo-mechanical couplings between the entrapped air, the in-pore liquid and the solid skeleton. This paper presents a fully coupled poromechanical model that separates the kinematics and the mechanical behaviours of the phases in their interactions with each other (e.g., liquid water, dissolved air, gaseous air and solid matrix). The assumptions about the entrapped air behaviour are defined from a bibliographic study, and linear elastic behaviour is used for both the liquid phase and the solid skeleton. The model is implemented in the FEM code COMSOL and is subsequently used to simulate oedometric tests under different loading paths: undrained compression or imposed liquid pressure variation at constant stress. The behaviour, which shows a continuous transition from unsaturated to saturated, is logical and consistent with available experimental data. 相似文献
18.
This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
19.
20.
In the effective stress equation for unsaturated soils proposed by Bishop, shear strength in these soils depends on the effective stress parameter, χ, a function of soil suction [1]. To estimate the shear strength of unsaturated soils, one must already know this parameter and its variation with soil suction. Though theories on the shear strength of unsaturated soils are consistent with experimental measurements, estimating the effective stress parameter directly from tedious laboratory tests is impractical. Thus, researchers have performed numerous intensive studies to effectively obtain the unsaturated shear strength using simplified empirical methods.This paper shows an adaptive learning neural network method for predicting this parameter, χ. The proposed network is a multilayer perceptron network with six neurons in the input layer representing the air entry value, the volumetric water content at residual and saturated conditions, the slope of soil water characteristic curve, the net confining stress and suction. The available literature uses a database prepared from triaxial shear test results to train and test the network. The results show the suitability of the proposed approach for estimating the effective stress parameter. Network analysis indicates that the χ-parameter depends strongly on the net mean stress. 相似文献