共查询到18条相似文献，搜索用时 406 毫秒
1.
2.
《地震工程与工程振动》2015,(3)
为了研究不同形式直榫榫卯节点的抗震性能,参照《营造法式》及相关文献的构造要求,考虑不同榫头形式、不同模型比例、不同榫头伸出长度及不同材料对直榫榫卯节点抗震性能的影响,制作了14个T型直榫榫卯节点。通过直榫节点的低周反复加载试验,得到了不同形式直榫节点的破坏特征、弯矩-转角滞回曲线、骨架曲线、转动刚度及其退化规律和耗能等性能。试验结果表明:直榫节点的破坏形态主要是卯口、榫头的挤压变形和榫头部分拔出,梁、柱无明显破坏;直榫节点弯矩-转角滞回曲线形状呈反‘S’型,单向直榫节点的滞回环对称且饱满度较好,透榫节点、半榫节点的正向和反向滞回曲线呈现不对称性且饱满度较差,半榫节点尤为明显;单向直榫节点、透榫节点的承载力和转动刚度较大且相差不多,半榫节点较小;单向直榫节点的承载力大致与模型比例的平方成正比,但不符合模型相似关系;单向直榫节点增加榫头长度有助于提高其转动刚度,但当榫头长度大于柱径时,其提高幅度减小;透榫节点的耗能能力好于单向直榫节点和半榫节点;不同木材种类对直榫节点的承载力、转动刚度等性能有明显影响;直榫节点的转角可以达到1/8rad,表现出良好的变形能力。研究成果可为古建筑木结构的抗震分析提供依据。 相似文献
3.
4.
5.
《地震工程与工程振动》2021,41(4)
为了研究带新型水平连接节点的预制叠合板式剪力墙结构的抗震性能,设计制作了两片采用新型水平连接节点的两层预制叠合剪力墙和一片作为对比的现浇剪力墙,其中两个预制构件连接形式分别为螺旋箍筋连接和钢板连接方式。对3个构件进行拟静力试验,分析结构的承载力、破坏机理、滞回性能、刚度退化、延性、耗能能力及拼装节点滑移情况等。试验结果表明:所有构件均呈现弯曲破坏特征,预制构件的极限层间位移角大于1/50,滞回曲线饱满,结构承载力接近于现浇剪力墙构件;采用新型连接节点的预制叠合剪力墙连接可靠,传力性能良好,预制构件底部相对滑移较小,整体抗震性能良好。 相似文献
6.
通过对2个新型装配式混凝土框架节点和1个现浇混凝土框架节点进行拟静力试验研究,对比分析装配式混凝土框架节点破坏特征、滞回曲线、骨架曲线、刚度退化和耗能能力等指标。研究结果表明:新型装配式混凝土框架节点比普通现浇混凝土框架节点具有较好的滞回性能,较高的耗能能力以及较缓的刚度退化。在满足梁筋锚固长度要求的前提下,预制梁内钢端头长度增加使框架节点抗震性能稍有提高。装配部分后浇混凝土可以提高框架节点的承载能力和刚度。采用ABAQUS有限元软件对节点进行数值模拟,发现模拟结果与试验结果吻合较好。 相似文献
7.
为了研究耗能段与RC框架梁采用不同连接节点形式对Y形偏心钢支撑RC框架结构滞回性能的影响,进行了2榀1/3缩尺Y形偏心钢支撑RC框架的低周反复荷载试验。介绍了试验过程,分析了试件在循环荷载作用下的破坏机理、滞回性能、延性、刚度退化规律以及耗能能力。试验结果表明:应用Y形偏心钢支撑加固RC框架合理可行,Y形偏心钢支撑承担了结构80%以上的水平荷载;U型外包钢与框架横梁连接的试件连接节点承载能力较高,耗能段耗能充分,结构的滞回曲线饱满;钢板与框架横梁底部连接的试件滞回曲线捏缩,耗能段耗能不充分,结构整体耗能能力差;U形外包钢与框架横梁连接的试件,耗能段破坏导致结构失效;钢板与框架梁底部连接的试件,连接节点破坏导致结构失效。 相似文献
8.
两层两跨方钢管混凝土框架抗震性能试验研究 总被引：1，自引：0，他引：1
为了研究采用穿芯高强螺栓-端板节点的方钢管混凝土框架的抗震性能,对一榀两层两跨的方钢管混凝土柱-钢梁框架进行了竖向荷载和低周反复水平荷载作用下的抗震性能试验研究,观测了框架的破坏形态,得到了框架试件的荷载-位移滞回曲线、骨架曲线,分析了方钢管混凝土框架的破坏机制、滞回性能、延性、耗能能力、强度及刚度退化等力学性能。结果表明:框架试件基本实现了梁铰破坏机制,具有良好的变形性能和耗能能力,位移延性系数为5.86~6.42,等效黏滞阻尼系数达到0.454,均满足延性框架的抗震要求。框架试件的强度和刚度退化较为平缓,具有较强的抗侧移能力。 相似文献
9.
钢管混凝土桥墩抗震性能试验研究 总被引：1，自引：0，他引：1
为研究钢管混凝土桥墩的抗震性能,对钢管混凝土桥墩和钢筋混凝土桥墩进行了拟静力对比试验研究。根据试件的破坏发展过程以及各试件的滞回曲线和骨架曲线,分析了其滞回性能、耗能能力、延性、强度退化及刚度退化等抗震性能。试验结果表明,钢管混凝土桥墩的抗震性能明显好于钢筋混凝土桥墩。在含钢率和轴力相同的情况下,钢管混凝土桥墩的滞回曲线比钢筋混凝土桥墩丰满得多,前者的耗能能力约为后者的4.46倍,钢管混凝土桥墩的延性大于钢筋混凝土桥墩;随着轴压比的增大,钢管混凝土桥墩延性有所下降,强度退化加快,但对其刚度退化的影响不大。 相似文献
10.
通过3个不同轴压比的预应力混凝土扁梁框架内节点试件的低周反复荷载加载试验,对节点的破坏形态、滞回曲线、延性、耗能能力以及刚度退化等抗震性能进行了初步研究,并着重探讨了轴压比对预应力混凝土扁梁框架内节点抗震性能的影响规律. 相似文献
11.
Rehabilitation of earthquake damaged external RC beam‐column joints by joint enlargement using prestressed steel angles 
下载免费PDF全文
下载免费PDF全文 Jalil Shafaei Abdollah Hosseini Mohammad Sadegh Marefat Jason M. Ingham 《地震工程与结构动力学》2017,46(2):291-316
The effectiveness of a rehabilitation method based on joint enlargement using prestressed steel angles to enhance the seismic behavior of damaged external reinforced concrete beam‐column joints was experimentally investigated. Three half‐scale joints having either non‐seismic or seismic reinforcement details were tested both before and after rehabilitation by applying lateral cyclic loading of increasing amplitudes. Two defects were considered for the two non‐seismic units, being the absence of transverse steel hoops and insufficient bond capacity of beam bottom steel reinforcing bars in the joint panel zone. The damaged specimens were rehabilitated by injecting epoxy grout into existing cracks and installing stiffened steel angles at the re‐entrant corners of the beam‐column joint, both above and below the beam, that were mounted and held in place using prestressed high‐tensile strength bars. The test results indicated that the seismic performance of the rehabilitated specimens in terms of strength, stiffness, and ductility was fully recovered and comparable with the performance of the seismically detailed specimen. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
12.
Seismic performance of steel reinforced ultra high-strength concrete composite frame joints 总被引：1，自引：1，他引：0
To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC)
columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically
lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the
frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation
and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in
the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints
increased as the axial load ratio decreased and the volumetric stirrup ratio increased. The displacement ductility coefficient
and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete
(SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength
degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a
low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint
specimens with better seismic performance may be a useful reference in future engineering applications. 相似文献
13.
以一字形竖缝耗能预制剪力墙作为研究对象,设计了3个装配式剪力墙试件及1个现浇剪力墙对比试件,进行低周往复荷载试验,并对破坏墙体进行CFRP加固,再次进行拟静力试验。试件变化参数包括轴压比、混凝土强度等级及配筋率,对比分析加固前后试件滞回性能、刚度退化、承载力和耗能能力等性能。试验结果表明,与现浇剪力墙相比,一字形竖缝耗能预制剪力墙工作性能良好,阻尼器屈服耗能提高了试件整体工作性能;CFRP加固可有效抑制墙体斜裂缝的发展,对墙体承载力及耗能能力均有显著改善作用;各试件均满足剪力墙弹塑性层间位移角限值要求,延性较好;试件整体表现出良好的抗震性能。 相似文献
14.
现存的传统村落木结构民居,由于受风雨侵蚀及战乱、地震、火灾的破坏,发生不同程度的损伤和破坏,榫卯节点残损情况直接影响整个民居房屋结构的安全。以北方地区传统村落“四梁八柱”木结构民居榫卯节点（馒头榫）为研究对象,考虑不同残损类型及程度,制作5个足尺梁柱节点模型,通过拟静力低周往复加载试验研究其破坏模式、弯矩-转角滞回响应及骨架曲线、加载刚度、变形、强度及耗能能力等力学性能。试验结果表明:馒头榫节点破坏模式表现为榫头拔出、榫与卯口挤压变形;相比于完好节点,残损馒头榫节点抗弯承载力、加载刚度和耗能能力明显降低,且“捏拢”效应加剧;榫头松动是导致节点力学性能降低的直接原因;垂直加载方向虫蛀节点力学性能劣化程度强于平行加载方向虫蛀节点,更易导致耗能能力降低。 相似文献
15.
隔板贯通式梁柱节点抗震性能试验研究 总被引：6，自引：0，他引：6
设计了低周反复荷载作用下3个十字形足尺隔板贯通式梁柱节点试件(其中2个节点的柱子浇筑了混凝土,1个为空钢管)的拟静力试验。通过研究拟静力试验所得的滞回曲线求得该节点的等效阻尼比,衡量它的耗能能力。从恢复力特性曲线得到了和一次加载相接近的骨架曲线,节点的初始刚度和刚度退化等参数。通过这些从强度、变形和能量等三方面判别和鉴定隔板贯通式梁柱节点的抗震性能,并得出了一些具有参考价值的结论。 相似文献
16.
The use of a new type of reinforced concrete (RC) jacket for RC exterior beam–column connections damaged by seismic excitations is addressed and experimentally investigated. The proposed jacket has very small thickness and includes small diameter steel reinforcement. This jacketing applies at the joint region and at a small part of the columns and the beam. The main advantage of the proposed thin and locally applied jacket compared with the commonly used concrete jacket is the fact that its application is not restrained by space limitations, and since it slightly changes the initial size of the elements, the building's dynamics and seismic behaviour remain practically unaffected. For the needs of this study, 10 exterior beam–column joint subassemblages were constructed and subjected to increasing cyclic loading. Later, the damaged specimens were locally retrofitted using the proposed thin RC jackets and they were retested with the same load sequence. Three different specimen configurations with various amounts of shear reinforcement in the joint area were examined and two types of jackets (a) with light and (b) with dense reinforcement were applied. Test results indicated that the seismic performance of the retrofitted specimens was fully restored and in some cases substantially improved with respect to the performance of the same specimens in the initial loading, since they exhibited higher values of load capacity and hysteretic energy dissipation. Discussion for the conditions of the use of the examined jacketing technique either as a repair or as a strengthening method is also included. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
17.
为推广装配式混凝土框架结构的应用,提出3种不同的新型装配式钢筋混凝土框架中节点连接形式,进行低周往复荷载试验。对比各试件的破坏形态、滞回性能、刚度退化、累积耗能和节点剪切变形等抗震指标。研究结果表明:采用方钢管连接的装配式混凝土节点呈现梁端弯曲破坏,采用工字钢连接或对拉螺栓连接的节点呈现节点核心区剪切破坏。采用方钢管的连接形式既能改善节点核心区的破坏形态,又能提高其承载能力、变形能力、耗能能力和梁端转动能力,同时显著改善节点的滞回特性,减小核心区的剪切变形。在弹塑性和塑性变形阶段,采用方钢管连接形式的装配式混凝土节点的抗震性能优于工字钢连接和对拉螺栓连接的节点。此外,采用工字钢连接形式比对拉螺栓连接形式的节点具有更高的承载能力、耗能能力和较小的核心区剪切变形。 相似文献
18.
为研究加固后锈蚀箍筋约束混凝土柱的抗震性能,设计16个钢筋混凝土矩形柱,对加速锈蚀后的试件采用外包钢及CFRP、GFRP材料进行加固处理,随后开展低周往复荷载试验,以研究不同加固材料、不同加固包裹方式、不同黏结材料等因素对锈蚀箍筋约束混凝土柱滞回曲线、骨架曲线、刚度衰减、延性性能及耗能能力等抗震性能指标的影响。研究结果表明:(1)与未锈蚀柱相比,加固后的箍筋锈蚀柱以弯剪破坏为主,CFRP加固试件较GFRP加固试件具有更高的承载力,但破坏时延性不如GFRP加固试件;(2)外包钢加固试件、CFRP加固试件、GFRP加固试件的耗能能力较未锈蚀试件分别增大222.3%、123.9%、98.5%,延性系数也相应增大45.3%、22.3%、25.6%。总之,外包钢加固对箍筋锈蚀柱抗震性能的提升最大,CFRP加固次之,但优于GFRP加固;整包加固优于环包加固;环氧树脂胶黏结略优于水泥基灌浆料黏结。 相似文献