首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 51 毫秒
1.
Boreholes drilled through contaminated zones in fractured rock create the potential for vertical movement of contaminated ground water between fractures. The usual assumption is that purging eliminates cross contamination; however, the results of a field study conducted in a trichloroethylene (TCE) plume in fractured sandstone with a mean matrix porosity of 13% demonstrates that matrix-diffusion effects can be strong and persistent. A deep borehole was drilled to 110 m below ground surface (mbgs) near a shallow bedrock well containing high TCE concentrations. The borehole was cored continuously to collect closely spaced samples of rock for analysis of TCE concentrations. Geophysical logging and flowmetering were conducted in the open borehole, and a removable multilevel monitoring system was installed to provide hydraulic-head and ground water samples from discrete fracture zones. The borehole was later reamed to complete a well screened from 89 to 100 mbgs; persistent TCE concentrations at this depth ranged from 2100 to 33,000 microg/L. Rock-core analyses, combined with the other types of borehole information, show that nearly all of this deep contamination was due to the lingering effects of the downward flow of dissolved TCE from shallower depths during the few days of open-hole conditions that existed prior to installation of the multilevel system. This study demonstrates that transfer of contaminant mass to the matrix by diffusion can cause severe cross contamination effects in sedimentary rocks, but these effects generally are not identified from information normally obtained in fractured-rock investigations, resulting in potential misinterpretation of site conditions.  相似文献   

2.
Remediation of groundwater contaminated by chlorinated hydrocarbons via in situ technologies such as direct injection of nanoscale zero valent iron (ZVI, Fe(O)) particles is increasingly common. However, assessing target compound degradation by abiotic processes is difficult because (1) the injection may displace the contaminant plume so that concentration measurements alone are often inconclusive and (2) biodegradation may also occur, making it challenging to identify and evaluate the abiotic degradation component. In this study, trichloroethylene (TCE) and 1,1,1-trichloroethane (1,1,1-TCA) were treated in a highly heterogeneous hydrogeologic setting. The purpose of this study was to evaluate the potential for compound-specific stable isotope analysis (CSIA) to monitor the effectiveness of ZVI injection by assessing TCE and 1,1,1-TCA degradation. Prior to ZVI injection, carbon isotope measurements demonstrated biodegradation of TCE by native microorganisms. This in situ biodegradation was quantified by measuring the enrichment of 13C in TCE samples downstream of the suspected source. When ZVI was injected through only two injection wells, no changes in TCE and 1,1,1-TCA isotope signatures were detected compared to preinjection values. In contrast, when ZVI was injected through 11 wells covering a greater portion of the contaminated area, 5 out of 10 monitoring wells showed further enrichment of 13C in either TCE or 1,1,1-TCA, indicating additional target compound transformation. The abiotic nature of this TCE transformation was confirmed through temporal trends in carbon isotope values of the putative transformation products cis-dichloroethylene (cis-DCE), ethene and ethane. This demonstrates the usefulness of CSIA in distinguishing abiotic vs. biotic transformation in the field.  相似文献   

3.
A tracer test was conducted to characterize the flow of groundwater across a permeable reactive barrier constructed with plant mulch (a biowall) at the OU‐1 site on Altus Air Force Base, Oklahoma. This biowall is intended to intercept and treat groundwater contaminated by trichloroethylene (TCE) in a shallow aquifer. The biowall is 139‐m long, 7.3‐m deep, and 0.5‐m wide. Bromide was injected from an upgradient well into the groundwater as a conservative tracer, and was subsequently observed breaking through in monitoring wells within and downgradient of the biowall. The bromide breakthrough data demonstrate that groundwater entering the biowall migrated across it, following the slope of the local groundwater surface. The average seepage velocity of groundwater was approximately 0.06 m/d. On the basis of the Darcy velocity of groundwater and geometry of the biowall, the average residence time of groundwater in the biowall was estimated at 10 d. Assuming all TCE removal occurred in the biowall, the reduction in TCE concentrations in groundwater across the biowall corresponds to a first‐order attenuation rate constant in the range of 0.38 to 0.15 per d. As an independent estimate of the degradation rate constant, STANMOD software was used to fit curves through data on the breakthrough of bromide and TCE in selected wells downgradient of the injection wells. Best fits to the data required a first‐order degradation rate constant for TCE removal in the range of 0.13 to 0.17 per d. The approach used in this study provides an objective evaluation of the remedial performance of the biowall that can provide a basis for design of other biowalls that are intended to remediate TCE‐contaminated groundwater.  相似文献   

4.
A field study of oxygen-enhanced biodegradation was carried out in a sandy iron-rich ground water system contaminated with gasoline hydrocarbons. Prior to the oxygen study, intrinsic microbial biodegradation in the contaminant plume had depleted dissolved oxygen and created anaerobic conditions. An oxygen diffusion system made of silicone polymer tubing was installed in an injection well within an oxygen delivery zone containing coarse highly permeable sand. During the study, this system delivered high dissolved oxygen (DO) levels (39 mg/L) to the ground water within a part of the plume. The ground water was sampled at a series of monitors in the test zone downgradient of the delivery well to determine the effect of oxygen on dissolved BTEX, ground water geochemistry, and microbially mediated biodegradation processes. The DO levels and Eh increased markedly at distances up to 2.3 m (7.5 feet) downgradient. Potential biofouling and iron precipitation effects did not clog the well screens or porous medium. The increased dissolved oxygen enhanced the population of aerobes while the activity of anaerobic sulfate-reducing bacteria and methanogens decreased. Based on concentration changes, the estimated total rate of BTEX biodegradation rose from 872 mg/day before enhancement to 2530 mg/day after 60 days of oxygen delivery. Increased oxygen flux to the test area could account for aerobic biodegradation of 1835 mg/day of the BTEX. The estimated rates of anaerobic biodegradation processes decreased based on the flux of sulfate, iron (II), and methane. Two contaminants in the plume, benzene and ethylbenzene, are not biodegraded as readily as toluene or xylenes under anaerobic conditions. Following oxygen enhancement, however, the benzene and ethylbenzene concentrations decreased about 98%, as did toluene and total xylenes.  相似文献   

5.
Analysis of a vertical dipole tracer test in highly fractured rock   总被引：1，自引：0，他引：1  
The results of a vertical dipole tracer experiment performed in highly fractured rocks of the Clare Valley, South Australia, are presented. The injection and withdrawal piezometers were both screened over 3 m and were separated by 6 m (midpoint to midpoint). Due to the long screen length, several fracture sets were intersected, some of which do not connect the two piezometers. Dissolved helium and bromide were injected into the dipole flow field for 75 minutes, followed by an additional 510 minutes of flushing. The breakthrough of helium was retarded relative to bromide, as was expected due to the greater aqueous diffusion coefficient of helium. Also, only -25% of the total mass injected of both tracers was recovered. Modeling of the tracer transport was accomplished using an analytical one-dimensional flow and transport model for flow through a fracture with diffusion into the matrix. The assumptions made include: streamlines connecting the injection and withdrawal point can be modeled as a dipole of equal strength, flow along each streamline is one dimensional, and there is a constant Peclet number for each streamline. In contrast to many other field tracer studies performed in fractured rock, the actual travel length between piezometers was not known. Modeling was accomplished by fitting the characteristics of the tracer breakthrough curves (BTCs), such as arrival times of the peak concentration and the center of mass. The important steps were to determine the fracture aperture (240 microm) based on the parameters that influence the rate of matrix diffusion (this controls the arrival time of the peak concentration); estimating the travel distance (11 m) by fitting the time of arrival of the centers of mass of the tracers; and estimating fracture dispersivity (0.5 m) by fitting the times that the inflection points occurred on the front and back limbs of the BTCs. This method works even though there was dilution in the withdrawal well, the amount of which can be estimated by determining the value that the modeled concentrations need to be reduced to fit the data (approximately 50%). The use of two tracers with different diffusion coefficients was not necessary, but it provides important checks in the modeling process because the apparent retardation between the two tracers is evidence of matrix diffusion and the BTCs of both tracers need to be accurately modeled by the best fit parameters.  相似文献   

6.
The influence of source zone concentration reduction on solute plume detachment and recession times in fractured rock was investigated using new semianalytical solutions to transient solute transport in the presence of advection, dispersion, sorption, matrix diffusion, and first-order decay. Novel aspects of these solutions are: (1) the source zone concentration behavior is simulated using a constant concentration with the option for either an instantaneous reduction to zero concentration or an exponentially decaying source zone concentration initiated at some time (t*) after the source is introduced, and (2) different biodegradation rates in the fracture and rock matrix. These solutions were applied for sandstone bedrock and revealed that biodegradation in the matrix, not the fracture, may be the most significant attenuation mechanism and therefore may dictate remediation time scales. Also, instantaneous and complete source concentration reduction in aged plumes may not be beneficial with respect to plume response because back-diffusion can sustain plume migration for long periods of time. Moderate source zone concentration reduction has a similar impact on the rate of advance of the leading edge of the plume as aggressive concentration reduction. If the source zone concentration reduction half-life is less than the plume decay half-life, then volatile organic compound (VOC) mass sequestered in the rock matrix will ultimately dictate plume persistence and not the presence of the source zone.  相似文献   

7.
Deep-well injection into fractured sandstone is an option for the disposal of contaminated mine dewatering discharge from an open pit uranium mine. As part of the assessment of potential contaminant migration from deep-well injection, the effect of matrix diffusion was evaluated. An analytical mathematical model was developed for the simulation of the radial movement of a contaminant front away from an injection point under steady flow conditions in a planar fracture with uniform properties. The model includes the effects of advection in the fracture, diffusion of contaminants from the fracture into the rock matrix, and equilibrium adsorption on the fracture surface as well as in the rock matrix. Effective diffusion coefficients obtained from laboratory experiments on 11 intact core samples varied from 3.4 × 10−8 to 3.2 × 10−7 cm2/s. Model simulations were made with diffusion coefficient values in this range and with single-fracture injection rates estimated from fracture frequencies in boreholes, and from bulk hydraulic conductivity values obtained from field tests. Because of matrix diffusion, the rate of outward movement of the front of the nonreactive contaminants from the injection well is much slower than the rate of water flow in the fractures. Simulations of the movement of contaminants that undergo adsorption indicate that even a small distribution coefficient for the rock matrix causes the contaminants to remain very close to the injection well during the one-year period. The results of the simplified model demonstrate that matrix diffusion is an important process that cannot be neglected in the assessment of a waste disposal scheme located in fractured porous rock. However, in order to make a definitive assessment of the capability of matrix diffusion and associated matrix adsorption to significantly limit the extent of contaminant migration around injection wells, it would be necessary to conduct field tests such as a preliminary or experimental injection.  相似文献   

8.
In granite aquifers, fractures can provide both storage volume and conduits for groundwater. Characterization of fracture hydraulic conductivity (K) in such aquifers is important for predicting flow rate and calibrating models. Nuclear magnetic resonance (NMR) well logging is a method to quickly obtain near-borehole hydraulic conductivity (i.e., KNMR) at high-vertical resolution. On the other hand, FLUTe flexible liner technology can produce a K profile at comparable resolution but requires a fluid driving force between borehole and formation. For three boreholes completed in a fractured granite, we jointly interpreted logging NMR data and FLUTe K estimates to calibrate an empirical equation for translating borehole NMR data to K estimates. For over 90% of the depth intervals investigated from these boreholes, the estimated KNMR are within one order of magnitude of KFLUTe. The empirical parameters obtained from calibrating the NMR data suggest that “intermediate diffusion” and/or “slow diffusion” during the NMR relaxation time may occur in the flowing fractures when hydraulic aperture are sufficiently large. For each borehole, “intermediate diffusion” dominates the relaxation time, therefore assuming “fast diffusion” in the interpretation of NMR data from fractured rock may lead to inaccurate KNMR estimates. We also compare calibrations using inexpensive slug tests that suggest reliable KNMR estimates for fractured rock may be achieved using limited calibration against borehole hydraulic measurements.  相似文献   

9.
Liu C  Ball WP 《Ground water》2002,40(2):175-184
Vertical profiles of tetrachloroethene (or perchloroethylene, PCE) and trichloroethene (TCE) were used to validate a diffusion process in a natural aquitard at Dover Air Force Base, Delaware. PCE and TCE distributions in the aquitard underlying an unconfined aquifer were sampled from core tubes obtained at four times over the course of a 35-month field investigation within "test cells" that were isolated from the surrounding ground water by means of grout-sealed steel sheetpile barriers (Mackay et al. 2000). For the final 23 months of this period, boundary conditions at the aquifer/aquitard interface were such that a "back diffusion" of contaminants from the aquitard was induced. Modeling predictions of concentration changes were made on the basis of the earliest coring results and an assumption of sorption-retarded diffusion and using laboratory information about sorption and diffusion characteristics of the media. The predictive modeling was complicated by the fact that "initial" and "final" PCE and TCE distributions in the aquitard were measured at different (albeit proximate) coring locations, such that results reflect spatial variations in aquitard characteristics. This problem was solved by means of an inverse interpretation that involved spatial "translation" of observed profiles on the basis of the laboratory characterizations and assuming a common aquifer-side contaminant history. Predictions indicated substantial change in PCE and TCE concentrations within the upper aquitard (near the aquifer/aquitard interface) and the development of a back-diffusion profile up into the aquifer. Modeling also predicted comparatively minor profile changes in the deeper aquitard, and especially in the deep layer where sorption was strongest. All of these predicted effects were observed in the coring results. Although not exact, the agreement between predictions and observations was sufficiently good to justify the basic tenets of the diffusion model and to support a conclusion that major processes of advection and/or transformation were unimportant within the 35-month time scale of this work.  相似文献   

10.
This research demonstrates that groundwater contaminated by a relatively dilute but persistent concentration of 1,4‐dioxane (1,4‐D), approximately 60 μg/L, and chlorinated aliphatic co‐contaminants (1.4 to 10 μg/L) can be efficiently and reliably treated by in situ aerobic cometabolic biodegradation (ACB). A field trial lasting 265 days was conducted at Operable Unit D at the former McClellan Air Force Base and involved establishing an in situ ACB reactor through amending recirculated groundwater with propane and oxygen. The stimulated indigenous microbial population was able to consistently degrade 1,4‐D to below 3 μg/L while the co‐contaminants trichloroethene (TCE) and 1,2‐dichloroethane (1,2‐DCA) were decreased to below 1 μg/L and 0.18 μg/L, respectively. A stable treatment efficiency of more than 95% removal for 1,4‐D and 1,2‐DCA and of more than 90% removal for TCE was achieved. High treatment efficiencies for 1,4‐D and all co‐contaminants were sustained even without propane and oxygen addition for a 2‐week period.  相似文献   

11.
Matrix diffusion can attenuate the rate of plume migration in fractured bedrock relative to the rate of ground water flow for both conservative and nonconservative solutes of interest. In a system of parallel, equally spaced constant aperture fractures subject to steady-state ground water flow and an infinite source width, the degree of plume attenuation increases with time and travel distance, eventually reaching an asymptotic level. The asymptotic degree of plume attenuation in the absence of degradation can be predicted by a plume attenuation factor, beta, which is readily estimated as R' (phi(m)/phi(f)), where R' is the retardation factor in the matrix, phi(m) is the matrix porosity, and phi(f) is the fracture porosity. This dual-porosity relationship can also be thought of as the ratio of primary to secondary porosity. Beta represents the rate of ground water flow in fractures relative to the rate of plume advance. For the conditions examined in this study, beta increases with greater matrix porosity, greater matrix fraction organic carbon, larger fracture spacing, and smaller fracture aperture. These concepts are illustrated using a case study where dense nonaqueous phase liquid in fractured sandstone produced a dissolved-phase trichloroethylene (TCE) plume approximately 300 m in length. Transport parameters such as matrix porosity, fracture porosity, hydraulic gradient, and the matrix retardation factor were characterized at the site through field investigations. In the fractured sandstone bedrock examined in this study, the asymptotic plume attenuation factors (beta values) for conservative and nonconservative solutes (i.e., chloride and TCE) were predicted to be approximately 800 and 12,210, respectively. Quantitative analyses demonstrate that a porous media (single-porosity) solute transport model is not appropriate for simulating contaminant transport in fractured sandstone where matrix diffusion occurs. Rather, simulations need to be conducted with either a discrete fracture model that explicitly incorporates matrix diffusion, or a dual-continuum model that accounts for mass transfer between mobile and immobile zones. Simulations also demonstrate that back diffusion from the matrix to fractures will likely be the time-limiting factor in reaching ground water cleanup goals in some fractured bedrock environments.  相似文献   

12.
The effect of nutrient and surfactant addition on the biodegradation of phenanthrene was studied in a batch scale soil–slurry system using isolated Mycoplana sp. MVMB2strain. The study was conducted using an artificially phenanthrene spiked and as well as contaminated soil from petrochemical industrial site. Maximum phenanthrene degradation and subsequent high microbial growth were observed at optimum pH (pH 6) and C/N/P ratio (100:20:3). To investigate maximum substrate degradation potential of Mycoplana sp. MVMB2, very high concentrations of phenanthrene (50–200 mg/kg soil) were used. The organism was capable of degrading >60% for a concentration below 20 mg/kg soil and >40% for concentrations up to 200 mg/kg within 8 days. Further the influence of five different surfactants namely Span 80, Tween 20, Triton X‐100, cetyl trimethyl ammonium bromide, and sodium dodecyl sulfate were tested at their critical micelle concentration (CMC) levels for phenanthrene degradation in the soil. The addition of surfactant enhanced the biodegradation and a maximum of 84.49% was obtained for Triton X‐100. Complete phenanthrene degradation by Mycoplana sp. MVMB2 was observed at 3 CMC concentration of Triton X‐100. The optimized parameters obtained were used for the degradation of phenanthrene present in the contaminated soil and 98.6% biodegradation was obtained. Thus, the results obtained in the study suggested that biodegradation of phenanthrene by Mycoplana sp. MVMB2 appeared to be feasible to remediate phenanthrene rich contaminated sites.  相似文献   

13.
Mass discharge across transect planes is increasingly used as a metric for performance assessment of in situ groundwater remediation systems. Mass discharge estimates using concentrations measured in multilevel transects are often made by assuming a uniform flow field, and uncertainty contributions from spatial concentration and flow field variability are often overlooked. We extend our recently developed geostatistical approach to estimate mass discharge using transect data of concentration and hydraulic conductivity, so accounting for the spatial variability of both datasets. The magnitude and uncertainty of mass discharge were quantified by conditional simulation. An important benefit of the approach is that uncertainty is quantified as an integral part of the mass discharge estimate. We use this approach for performance assessment of a bioremediation experiment of a trichloroethene (TCE) source zone. Analyses of dissolved parent and daughter compounds demonstrated that the engineered bioremediation has elevated the degradation rate of TCE, resulting in a two‐thirds reduction in the TCE mass discharge from the source zone. The biologically enhanced dissolution of TCE was not significant (～5%), and was less than expected. However, the discharges of the daughter products cis‐1,2, dichloroethene (cDCE) and vinyl chloride (VC) increased, probably because of the rapid transformation of TCE from the source zone to the measurement transect. This suggests that enhancing the biodegradation of cDCE and VC will be crucial to successful engineered bioremediation of TCE source zones.  相似文献   

14.
Field characterization of a trichloroethene (TCE) source area in fractured mudstones produced a detailed understanding of the geology, contaminant distribution in fractures and the rock matrix, and hydraulic and transport properties. Groundwater flow and chemical transport modeling that synthesized the field characterization information proved critical for designing bioremediation of the source area. The planned bioremediation involved injecting emulsified vegetable oil and bacteria to enhance the naturally occurring biodegradation of TCE. The flow and transport modeling showed that injection will spread amendments widely over a zone of lower‐permeability fractures, with long residence times expected because of small velocities after injection and sorption of emulsified vegetable oil onto solids. Amendments transported out of this zone will be diluted by groundwater flux from other areas, limiting bioremediation effectiveness downgradient. At nearby pumping wells, further dilution is expected to make bioremediation effects undetectable in the pumped water. The results emphasize that in fracture‐dominated flow regimes, the extent of injected amendments cannot be conceptualized using simple homogeneous models of groundwater flow commonly adopted to design injections in unconsolidated porous media (e.g., radial diverging or dipole flow regimes). Instead, it is important to synthesize site characterization information using a groundwater flow model that includes discrete features representing high‐ and low‐permeability fractures. This type of model accounts for the highly heterogeneous hydraulic conductivity and groundwater fluxes in fractured‐rock aquifers, and facilitates designing injection strategies that target specific volumes of the aquifer and maximize the distribution of amendments over these volumes.  相似文献   

15.
Chlororespiration is common in shallow aquifer systems under conditions nominally identified as anoxic. Consequently, chlororespiration is a key component of remediation at many chloroethene‐contaminated sites. In some instances, limited accumulation of reductive dechlorination daughter products is interpreted as evidence that natural attenuation is not adequate for site remediation. This conclusion is justified when evidence for parent compound (tetrachloroethene, PCE, or trichloroethene, TCE) degradation is lacking. For many chloroethene‐contaminated shallow aquifer systems, however, nonconservative losses of the parent compounds are clear but the mass balance between parent compound attenuation and accumulation of reductive dechlorination daughter products is incomplete. Incomplete mass balance indicates a failure to account for important contaminant attenuation mechanisms and is consistent with contaminant degradation to nondiagnostic mineralization products like CO2. While anoxic mineralization of chloroethene compounds has been proposed previously, recent results suggest that oxygen‐based mineralization of chloroethenes also can be significant at dissolved oxygen concentrations below the currently accepted field standard for nominally anoxic conditions. Thus, reassessment of the role and potential importance of low concentrations of oxygen in chloroethene biodegradation are needed, because mischaracterization of operant biodegradation processes can lead to expensive and ineffective remedial actions. A modified interpretive framework is provided for assessing the potential for chloroethene biodegradation under different redox conditions and the probable role of oxygen in chloroethene biodegradation.  相似文献   

16.
Chlorinated solvents are one of the most commonly detected groundwater contaminants in industrial areas. Identification of polluters and allocation of contaminant sources are important concerns in the evaluation of complex subsurface contamination with multiple sources. In recent years, compound‐specific isotope analyses (CSIA) have been employed to discriminate among different contaminant sources and to better understand the fate of contaminants in field‐site studies. In this study, the usefulness of dual isotopes (carbon and chlorine) was shown in assessments of groundwater contamination at an industrial complex in Wonju, Korea, where groundwater contamination with chlorinated solvents such as trichloroethene (TCE) and carbon tetrachloride (CT) was observed. In November 2009, the detected TCE concentrations at the study site ranged between nondetected and 10,066 µg/L, and the CT concentrations ranged between nondetected and 985 µg/L. In the upgradient area, TCE and CT metabolites were detected, whereas only TCE metabolites were detected in the downgradient area. The study revealed the presence of separate small but concentrated TCE pockets in the downgradient area, suggesting the possibility of multiple contaminant sources that created multiple comingling plumes. Furthermore, the variation of the isotopic (δ13C and δ37Cl) TCE values between the upgradient and downgradient areas lends support to the idea of multiple contamination sources even in the presence of detectable biodegradation. This case study found it useful to apply a spatial distribution of contaminants coupled with their dual isotopic values for evaluation of the contaminated sites and identification of the presence of multiple sources in the study area.  相似文献   

17.
Thermal methods are promising for remediating fractured geologic media contaminated with volatile organic compounds, and the success of this process depends on the coupled heat transfer, multiphase flow, and thermodynamics. This study analyzed field‐scale removal of trichloroethylene (TCE) and heat transfer behavior in boiling fractured geologic media using the multiple interacting continua method. This method can resolve local gradients in the matrix and is less computationally demanding than alternative methods like discrete fracture‐matrix models. A 2D axisymmetric model was used to simulate a single element of symmetry in a repeated pattern of extraction wells inside a large heated zone and evaluate effects of parameter sensitivity on contaminant recovery. The results showed that the removal of TCE increased with matrix permeability, and the removal rate was more sensitive to matrix permeability than any other parameter. Increasing fracture density promoted TCE removal, especially when the matrix permeability was low (e.g., <10?17 m2). A 3D model was used to simulate an entire treatment zone and the surrounding groundwater in fractured material, with the interaction between them being considered. Boiling was initiated in the center of the upper part of the heated region and expanded toward the boundaries. This boiling process resulted in a large increase in the TCE removal rate and spread of TCE to the vadose zone and the peripheries of the heated zone. The incorporation of extraction wells helped control the contaminant from migrating to far regions. After 22 d, more than 99.3% of TCE mass was recovered in the simulation.  相似文献   

18.
Microbiological degradation of perchloroethylene (PCE) under anaerobic conditions follows a series of chain reactions, in which, sequentially, trichloroethylene (TCE), cis‐dichloroethylene (c‐DCE), vinylchloride (VC) and ethene are generated. First‐order degradation rate constants, partitioning coefficients and mass exchange rates for PCE, TCE, c‐DCE and VC were compiled from the literature. The parameters were used in a case study of pump‐and‐treat remediation of a PCE‐contaminated site near Tilburg, The Netherlands. Transport, non‐equilibrium sorption and biodegradation chain processes at the site were simulated using the CHAIN_2D code without further calibration. The modelled PCE compared reasonably well with observed PCE concentrations in the pumped water. We also performed a scenario analysis by applying several increased reductive dechlorination rates, reflecting different degradation conditions (e.g. addition of yeast extract and citrate). The scenario analysis predicted considerably higher concentrations of the degradation products as a result of enhanced reductive dechlorination of PCE. The predicted levels of the very toxic compound VC were now an order of magnitude above the maximum permissible concentration levels. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

19.
Contaminated groundwater in fractured bedrock can expose ecosystems to undesired levels of risk for extended periods due to prolonged back-diffusion from rock matrix to permeable fractures. Therefore, it is key to characterize the diffusive mass loading (intrusion) of contaminants into the rock matrix for successful management of contaminated bedrock sites. Even the most detailed site characterization techniques often fail to delineate contamination in rock matrix. This study presents a set of analytical solutions to estimate diffusive mass intrusion into matrix blocks, it is recovered by pumping and concentration rebound when pumping ceases. The analytical models were validated by comparing the results with (1) numerical model results using the same model parameters and (2) observed chloride mass recovery, rebound concentration, and concentration in pumped groundwater at a highly fractured bedrock site in Alberta, Canada. It is also demonstrated that the analytical solutions can be used to estimate the total mass stored in the fractured bedrock prior to any remediation thereby providing insights into site contamination history. The predictive results of the analytical models clearly show that successful remediation by pumping depends largely on diffusive intrusion period. The results of initial mass from the analytical model was used to successfully calibrate a three-dimensional discrete fracture network numerical model further highlighting the utility of the simple analytical solutions in supplementing the more detailed site numerical modeling. Overall, the study shows the utility of simple analytical methods to support long-term management of a contaminated fractured bedrock site including site investigations and complex numerical modeling.  相似文献   

20.
Air sparging has proven to be an effective remediation technique for treating saturated soils and ground water contaminated by volatile organic compounds (VOCs). Since little is known about the system variables and mass transfer mechanisms important to air sparging, several researchers have recently performed laboratory investigations to study such issues. This paper presents the results of column experiments performed to investigate the behavior of dense nonaqueous phase liquids (DNAPFs). specifically trichloroethylene (TCE), during air sparging. The specific objectives of the study were (1) to compare the removal of dissolved TCE with the removal of dissolved light nonaqueous phase liquids (LNAPLs). such as benzene or toluene; (2) to determine the effect of injected air-flow rate on dissolved TCE removal; (3) to determine the effect of initial dissolved TCE concentration on removal efficiency; and (4) to determine the differences in removal between dissolved and pure-phase TCE. The test results showed that (1) the removal of dissolved TCE was similar to that of dissolved LNAPL: (2) increased air-injection rates led to increased TCE removal at lower ranges of air injection, but further increases at higher ranges of air injection did not increase the rate of removal, indicating a threshold removal rate had been reached; (3) increased initial concentration of dissolved TCE resulted in similar rates of removal: and (4) the removal of pure-phase TCE was difficult using a low air-injection rate, but higher air-injection rates led to easier removal.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号