共查询到20条相似文献，搜索用时 78 毫秒
1.
2.
根据河口海岸水沙输移的特点,建立了一个新的二维分组数学模型,用来预测该区域的水沙输移过程。该模型耦合了水动力模块、泥沙输移模块和床面演变模块。其中水动力模块基于浅水方程组,综合考虑了柯氏力、床面切应力以及表面风应力的影响,引入干湿判断法处理动边界。泥沙输移模块首先将泥沙按照粒径分组,针对不同泥砂性质,对各组泥沙分别进行建模求解。床面演变模块基于质量守恒方程,实时更新床面高程以及床沙级配变化,并传递给水动力模块,更新底部边界。该模型被应用在了英国塞汶(Severn)河口,其预测的泥沙浓度和实测数据以及不分组的模型的预测结果进行了比较,结果显示,文中建立的分组模型预测的结果要明显好于不分组模型。 相似文献
3.
4.
5.
黄河在调水调沙影响下的入海泥沙通量和粒度的变化趋势 总被引：1，自引：0，他引：1
《海洋地质前沿》2015,(7)
基于1950—2013年的黄河水文泥沙资料,系统研究了黄河实施调水调沙以来入海泥沙在通量、粒度组成和时间分布上的变化特征,揭示了调水调沙影响下黄河入海泥沙的变化趋势。在2002年黄河实施调水调沙以来,6—11月平缓均衡的持续性高水沙量取代了调水调沙之前7—10月峰值尖瘦的汛期特征,汛期与非汛期差异减小,入海水沙通量的季节性特征显著改变。随着调水调沙的逐年实施,河床泥沙颗粒粗化,临界起动功率不断增大,而调水调沙期间的径流量峰值基本稳定,径流对下游河床冲刷效率不断降低,导致入海泥沙通量持续降低、泥沙颗粒变细。可以预见,黄河河口的淤积将会大大减缓,入海的泥沙将更多地沉积在远离河口的区域,维持河口三角洲叶瓣冲淤平衡的临界泥沙量将会加大。 相似文献
6.
7.
渤海动力对黄河入海泥沙输移的影响 总被引：3，自引：0，他引：3
海洋动力过程对黄河入海泥沙的淤积和扩散具有决定性作用 ,利用三维斜压动力 -泥沙模型分析了黄河口外海域潮流动力变化与黄河入海泥沙淤积、扩散特性之间的响应关系。季节环流以及涨落潮的分布和变化很好地解释了黄河口南北浮泥的形成和消长变化以及黄河入海泥沙向海扩散的机理。结果表明 ,入海泥沙在洪季、枯季和表底层都具有不同的输移特性 相似文献
8.
9.
河口泥沙运动有其独特的规律,需要采用高分辨率的观测手段进行系统的现场观测,以此发现河口流速和泥沙分布结构,进而探讨其形成机制,应用声学多普勒流速剖面仪和声学悬浮泥沙观测系统,通过定点和走航式观测长江河口不同潮型和流态下流速和悬浮泥沙浓度时空分布发现:(1)不同潮型出现高浓度“事件”的次数和成因存在差异,中潮型出现高浓度“事件”的可能性最大;(2)抛泥泥沙浓度垂向分布至少有3种结构类型,即上小下大的“L”型、指数型和上大下小的“漂浮”型;(3)受抛泥泥沙输移的影响,断面流场形成低流速区,它们的强度随落潮流的扩散逐渐减弱;(4)不同潮型的落潮流表现出不同的输移行为,大、小潮型落潮流偏北,中潮型落潮流偏南;(5)在落潮流和颗粒重力共同作用下抛泥泥沙同时存在输移扩散和沉降过程,小潮型抛泥泥沙主要就近扩散和沉降,中潮和大潮型抛泥泥沙输移扩散范围较远。 相似文献
10.
渤海动力对黄河入海泥沙输移的影响 总被引：7，自引：0，他引：7
海洋动力过程对黄河入海泥沙的淤积和扩散具有决定性作用，利用三维斜压动力－泥沙模型分析了黄河口外海域潮流动力变化与黄河入海泥沙淤积，扩散特性之间的响应关系，季节环流以及涨落潮的分布和变化很好地解释了黄河口南北浮泥的形成和消长变化以及黄河入海泥沙向海扩散的机理，结果表明，入海泥沙在洪季，枯季和表底层都具有不同的输移特性。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.