首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Pyrolysis experiments were carried out on Monterey formation kerogen and bitumen and Green River formation kerogen (Type II and I, respectively), in the presence and absence of montmorillonite, illite and calcite at 200 and 300°C for 2–2000 hours. The pyrolysis products were identified and quantified and the results of the measurements on the gas and condensate range are reported here.A significant catalytic effect was observed for the pyrolysis of kerogen with montmorillonite, whereas small or no effects were observed with illite and calcite, respectively. Catalytic activity was evident by the production of up to five times higher C1–C6 hydrocarbons for kerogen with montmorillonite than for kerogen alone, and by the dominance of branched hydrocarbons in the C4–C6 range (up to 90% of the total amount at any single carbon number). This latter effect in the presence of montmorillonite is attributed to cracking via a carbonium-ion [carbocation] intermediate which forms on the acidic sites of the clay. No catalytic effect, however, was observed for generation of methane and C2 hydrocarbons which form by thermal cracking. The catalysis of montmorillonite was significantly greater during pyrolysis of bitumen than for kerogen, which may point to the importance of the early formed bitumen as an intermediate in the production of low molecular weight hydrocarbons. Catalysis by minerals was also observed for the production of carbon dioxide.These results stress the importance of the mineral matrix in determining the type and amount of gases and condensates forming from the associated organic matter under thermal stress. The literature contains examples of gas distributions in the geologic column which can be accounted for by selective mineral catalysis, mainly during early stages of organic matter maturation.  相似文献   

2.
Kerogen was isolated from a marine sediment from Tanner Basin, offshore California. Samples of the kerogen were heated under an inert atmosphere at various temperatures and times. The heated and unheated kerogens were subjected to alkaline potassium permanganate oxidation followed by GC/ MS analysis of the products. The kerogens yielded primarily aliphatic C2–C14 α,ω-dicarboxylic acids and benzene mono-to-pentacarboxylic acids. Yields of aliphatic dicarboxylic acids from kerogen decreased with increasing thermal alteration. Yields of benzenecarboxylic acids increased steadily with increasing thermal alteration. The data support the concept that thermal maturation during natural burial of this type of kerogen results in the generation of aliphatic hydrocarbons from an increasingly aromatic residue.  相似文献   

3.
An immature sulfur-rich marl from the Gessosso-solfifera Formation of the Vena del Gesso Basin (Messinian, Italy) has been subjected to hydrous pyrolysis (160 to 330°C) to simulate maturation under natural conditions. The kerogen of the unheated and heated samples was isolated and the hydrocarbons released by selective chemical degradation (Li/EtNH2 and HI/LiAlH4) were analysed to allow a study of the fate of sulfur- and oxygen-bound species with increasing temperature. The residues from the chemical treatments were also subjected to pyrolysis–GC to follow structural changes in the kerogens. In general, with increasing hydrous pyrolysis temperature, the amounts of sulfide- and ether-bound components in the kerogen decreased significantly. At the temperature at which the generation of expelled oil began (260°C), almost all of the bound components initially present in the unheated sample were released from the kerogen. Comparison with an earlier study of the extractable organic matter using a similar approach and the same samples provides molecular evidence that, with increasing maturation, solvent-soluble macromolecular material was initially released from the kerogen, notably as a result of thermal cleavage of weak carbon–heteroatom bonds (sulfide, ester, ether) even at temperatures as low as 220°C. This solvent-soluble macromolecular material then underwent thermal cleavage to generate hydrocarbons at higher temperatures. This early generation of bitumen may explain the presence of unusually high amounts of extractable organic matter of macromolecular nature in very immature S-rich sediments.  相似文献   

4.
Organic geochemical analyses of fine-grained rocks from the 9.590 km Bertha Rogers No. 1 well have been carried out: total organic carbon, Soxhlet extraction and silica gel chromatography, C15+ saturated and aromatic hydrocarbon gas chromatography and mass spectrometry, pyrolysis, kerogen analysis, X-ray diffraction and visual kerogen analysis.Rocks ranged in age from Permian to Ordovician; the well has an estimated bottom hole temperature of 225°C. Some data from this study are inconsistent with conventional theories concerning the generation and thermal destruction of hydrocarbons. For example, appreciable amounts of C15+ gas-condensate-like hydrocarbons are present in very old rocks currently at temperatures where current theory predicts that only methane and graphite should remain. Also, substantial amounts of pyrolyzable C15+ hydrocarbons remain on the kerogen in these deeply buried Paleozoic rocks. This suggests, at least in somes cases, that temperatures much higher than those predicted by current theory are required for generation and thermal destruction of hydrocarbons. The data from this well also suggest that original composition of organic matter and environment of deposition may have a much stronger influence on the organic geochemical characteristics of fine-grained sediments than has previously been ascribed to them. The results from this well, from other deep hot wells in which temperatures exceed 200°C, and from laboratory experiments, suggest that some of the basic concepts of the generation and maturation of petroleum hydrocarbons may be in error and perhaps should be reexamined.  相似文献   

5.
《Applied Geochemistry》1988,3(5):441-453
Green River shale (Type I kerogen), Yaamba shale (Type II kerogen) and Sarufutsu coal (Type III kerogen) were heated to various temperatures using Rock-Eval. The amount of hydrocarbons generated and weight loss by pyrolysis were measured to obtain a better understanding of petroleum generation. After the pyrolysis experiments, elemental analysis (C, H), vitrinite reflectance (%Ro) measurement, maceral observation, infrared spectroscopy (IR) and13C-NMR spectroscopy were carried out on the coal samples. Changes in H/C atomic ratio, IR and NMR spectra indicate that experiments by Rock-Eval resemble those of the natural evolution of kerogen. However, the petrographic changes of the coal show more similarity to coal liquefaction and coking than to natural coalification. Changes in the amount of generated hydrocarbons with increasing maturation show that Type II kerogen produces more hydrocarbons than does Type I when Ro does not exceed 1.1%. Petroleum generation curves for the three samples were concordant with trends in natural systems, and a conceptual model of petroleum generation curve classified into three types is proposed, namely (1) curve of total amount enerated, (2) curve of generation rate, and (3) curve of fluid composition. Changes of IR and NMR spectra after pyrolysis imply that generated hydrocarbons are derived from aliphatic C structures of kerogen macromolecules. Moreover, the difference in genetic potential between Type I and Type III reflects different amounts of aliphatic structures. Type I is assumed to have a simple assemblage (mainly polymethylene carbons), and Type III is assumed to have a more complex variety of structures that are responsible for the difference in generation rates between the two kerogen Types. A quantitative analysis of C species of various bond structure by13C-NMR confirms that petroleum generation is the process of bond cleavage of kerogen macromolecules; lower-energy bonds decrease at an earlier stage of reaction, while aromatic carbons with higher bond energies survive to form graphitic structure at postmature stages. Emphasis is placed on the idea that the most important and direct factor in petroleum generation is a change in the molecular structure of kerogen with increasing maturation. NMR and other methods providing information about molecular structures of kerogen will become strong tools for evaluating source rocks and sedimentary basins in the future.  相似文献   

6.
The thermal reactivity of organic matter in source rocks is usually kinetically represented by a set of parallel and independent first order reactions. The approach assumes that only defunctionalisation reactions take place upon thermal decomposition, regardless of the chemical nature of kerogen. We have developed a new method for evaluating maturation pathways for an important kerogen-forming geopolymer, algaenan from the alga Botryococcus braunii (B. braunii), involving molecular dynamic reactive modelling based on quantum mechanics to reproduce maturation. To achieve this, a structural model is first constructed on the basis of models from the literature and analytical characterization of our samples using modern 1D and 2D nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared spectroscopy (FTIR) and elemental analysis (EA). Then, thermal decomposition of the algaenan is performed at low conversion in order to describe the initial transformations analytically. In an additional step, the observed chemical changes are quantitatively and qualitatively compared to simulated maturation from the molecular models. From this simulated maturation detailed reaction schemes are extracted for primary cracking mechanisms.  相似文献   

7.
A laboratory heating experiment was conducted in an attempt to evaluate the possible role of lipids as precursors for petroleum hydrocarbons. Lipids were extracted from a Recent lake sediment (Lake Haruna, Japan), and heated under N2 atmosphere, at 125–370°C, for 1–7 days. A significant amount of lipids was polymerized to kerogen-like matter (lipid-derived kerogen) at the low temperature of 175°C for 1 day. The polymerization follows first-order kinetics, and the half life of lipids is calculated to be 104–105 yr at 0–30°C. The lipid-derived kerogen generated a significant amount (62 mg/g) of n-alkanes (C14–C36) on heating at 350°C for 1 day.The results indicate a possible occurrence of lower temperature thermal polymerization of lipids in a relatively early stage of diagenesis as one of the formation pathways of kerogen with high hydrocarbon producing potential.  相似文献   

8.
A thermal analysis-gas chromatography technique, previously described by Whelan et al. has been used to analyze cuttings from a Continental Offshore Stratigraphic Test (COST No. 1) drilled in the Gulf Coast of the U.S.A. The data allowed an evaluation of the degree of maturation of the organic matter and provided an accurate determination of the depth of the threshold of intense oil generation at 3048 m (10,000 ft.). Qualitative changes of hydrocarbons in the C7–C14 range were determined by gas chromatography and confirmed by gas chromatography-mass spectroscopy. These data are discussed in terms of generation and migration processes. The catagenetic evolution results in a strong tendency for a proportional increase in n-alkanes. Mass transfer phenomena may be responsible for updip movement of the lighter hydrocarbons.  相似文献   

9.
Three fractions of organic matter: lipid (benzene:methanol-extractable), humic acid (alkali-extractable) and kerogen (residue) were extracted from a young marine sediment (Tanner Basin, offshore southern California) and heated for different times (5–116 hr) and temperatures (150°–410°C). The volatile (gases) and liquid products, as well as residual material, were then analyzed. On a weight basis, the lipid fraction produced 58% of the total identified n-alkanes, the kerogen fraction 41%, and the humic acid <1%. Whereas n-alkanes produced from lipid show a CPI > 1.0, those produced by thermal alteration of kerogen display a CPI < 1.0. The volatiles produced by heating the lipid and humic acid fractions were largely CO2 and water, whereas those produced from heated kerogen also included methane, hydrogen gas and small amounts of C2–C4 hydrocarbons. A mechanism for hydrocarbon production due to the thermal alteration of organic constituents of marine sediment is discussed.  相似文献   

10.
Mathematical models of hydrocarbon formation can be used to simulate the natural evolution of different types of organic matter and to make an overall calculation of the amounts of oil and/or gas produced during this evolution. However, such models do not provide any information on the composition of the hydrocarbons formed or on how they evolve during catagenesis.From the kinetic standpoint, the composition of the hydrocarbons formed can be considered to result from the effect of “primary cracking” reactions having a direct effect on kerogen during its evolution as well as from the effect of “secondary cracking” acting on the hydrocarbons formed.This report gives experimental results concerning the “primary cracking” of Types II and III kerogens and their modelling. For this, the hydrocarbons produced have been grouped into four classes (C1, C2–C5, C6–C15 and C15+). Experimental data corresponding to these different classes were obtained by the pyrolysis of kerogens with temperature programming of 4°C/min with continuous analysis, during heating, of the amount of hydrocarbons corresponding to each of these classes.The kinetic parameters of the model were optimized on the basis of the results obtained. This model represents the first step in the creation of a more sophisticated mathematical model to be capable of simulating the formation of different hydrocarbon classes during the thermal history of sediments. The second step being the adjustment of the kinetic parameters of “secondary cracking”.  相似文献   

11.
High maturity oil and gas are usually generated after primary oil expulsion from source rocks, especially from oil prone type I/II kerogen. However, the detailed impacts of oil expulsion, or retention in source rock on further thermal degradation of kerogen at the high maturity stage remain unknown. In the present study, we collected an Ordovician Pingliang shale sample containing type II kerogen. The kerogens, which had previously generated and expelled oil and those which had not, were prepared and pyrolyzed in a closed system, to observe oil expulsion or oil retention effects on later oil and gas generation from kerogen. The results show that oil expulsion and retention strongly impacts on further oil and gas generation in terms of both the amount and composition in the high maturity stage. Gas production will be reduced by 50% when the expulsion coefficient reaches 58%, and gas from oil-expelled kerogen (less oil retained) is much drier than that from fresh kerogen. The oil expulsion also causes n-alkanes and gas compounds to have heavier carbon isotopic compositions at high maturity stages. The enrichment of 13C in n-alkanes and gas hydrocarbons are 1‰ and 4–6‰ respectively, compared to fresh kerogen. Oil expulsion may act as open system opposite to the oil retention that influences the data pattern in crossplots of δ13C2–δ13C3 versus C2/C3, δ13C2–δ13C3 versus δ13C1 and δ13C1–δ13C2 versus ln(C1/C2), which are widely used for identification of gas from kerogen cracking or oil cracking. These results suggest that the reserve estimation and gas/source correlation in deep burial basins should consider the proportion of oil retention to oil expulsion the source rocks have experienced.  相似文献   

12.
Aromatic hydrocarbons from benzene extracts of New Albany Shale were characterized. A biomarker that has a molecular weight of 546 and a structural configuration consistent with that of an alkyl-aromatic hydrocarbon (C40H66) was tentatively identified. It was found that the relative concentrations of the biomarker are indicative of differing levels of thermal maturity of the shale organic matter. A 40-carbon bicyclic carotenoid (C40H48) is proposed as the geochemical precursor of this biomarker. Thermal maturity of the shale organic matter can also be differentiated by observing differences in “fingerprints” as obtained by field-ionization mass spectrometry on the aromatic hydrocarbon fraction. Using this technique, we found that the more mature shale samples from southeastern Illinois contain more low molecular weight extractable aromatic hydrocarbons and the less mature shale samples from northwestern Illinois contain more high molecular weight extractable aromatic hydrocarbons. It was demonstrated that field-ionization and tandem mass spectrometric techniques through fingerprint and individual compound identification, are useful for shale aromatic hydrocarbon fraction characterization and for thermal maturation interpretation.  相似文献   

13.
Kerogen plays an important role in shale gas adsorption, desorption and diffusion. Therefore, it is necessary to characterize the molecular structure of kerogen. In this study, four kerogen samples were isolated from the organic-rich shale of the Longmaxi Formation. Raman spectroscopy was used to determine the maturity of these kerogen samples. High-resolution transmission electron microscopy (HRTEM), 13C nuclear magnetic resonance (13C NMR) , X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy were conducted to characterize the molecular structure of the shale samples. The results demonstrate that VReqv of these kerogen samples vary from 2.3% to 2.8%, suggesting that all the kerogen samples are in the dry gas window. The macromolecular carbon skeleton of the Longmaxi Formation kerogen is mainly aromatic (fa’=0.56). In addition, the aromatic structural units are mainly composed of naphthalene (23%), anthracene (23%) and phenanthrene (29%). However, the aliphatic structure of the kerogen macromolecules is relatively low (fal*+falH=0.08), which is presumed to be distributed in the form of methyl and short aliphatic chains at the edge of the aromatic units. The oxygen-containing functional groups in the macromolecules are mainly present in the form of carbonyl groups (fac=0.23) and hydroxyl groups or ether groups (falO=0.13). The crystallite structural parameters of kerogen, including the stacking height (Lc=22.84 ?), average lateral size (La=29.29 ?) and interlayer spacing (d002=3.43 ?), are close to the aromatic structural parameters of anthracite or overmature kerogen. High-resolution transmission electron microscopy reveals that the aromatic structure is well oriented, and more than 65% of the diffractive aromatic layers are concentrated in the main direction. Due to the continuous deep burial, the longer aliphatic chains and oxygen-containing functional groups in the kerogen are substantially depleted. However, the ductility and stacking degree of the aromatic structure increases during thermal evolution. This study provides quantitative information on the molecular structure of kerogen samples based on multiple research methods, which may contribute to an improved understanding of the organic pores in black shale.  相似文献   

14.
The organic geochemical methods of hydrocarbon prospecting involve the characterization of sedimentary organic matter in terms of its abundance, source and thermal maturity, which are essential prerequisites for a hydrocarbon source rock. In the present study, evaluation of organic matter in the outcrop shale samples from the Semri and Kaimur Groups of Vindhyan basin was carried out using Rock Eval pyrolysis. Also, the adsorbed low molecular weight hydrocarbons, methane, ethane, propane and butane, were investigated in the near surface soils to infer the generation of hydrocarbons in the Vindhyan basin. The Total Organic Carbon (TOC) content in shales ranges between 0.04% and 1.43%. The S1 (thermally liberated free hydrocarbons) values range between 0.01–0.09 mgHC/gRock (milligram hydrocarbon per gram of rock sample), whereas the S2 (hydrocarbons from cracking of kerogen) show the values between 0.01 and 0.14 mgHC/gRock. Based on the Tmax (temperature at highest yield of S2) and the hydrogen index (HI) correlations, the organic matter is characterized by Type III kerogen. The adsorbed soil gas, CH4 (C1), C2H6 (C2), C3H8 (C3) and nC4H10, (nC4), concentrations measured in the soil samples from the eastern part of Vindhyan basin (Son Valley) vary from 0 to 186 ppb, 0 to 4 ppb, 0 to 5 ppb, and 0 to 1 ppb, respectively. The stable carbon isotope values for the desorbed methane (δ13C1) and ethane (δ13C2) range between −45.7‰ to −25.2‰ and −35.3‰ to −20.19‰ (VPDB), respectively suggesting a thermogenic source for these hydrocarbons. High concentrations of thermogenic hydrocarbons are characteristic of areas around Sagar, Narsinghpur, Katni and Satna in the Son Valley. The light hydrocarbon concentrations (C1–C4) in near surface soils of the western Vindhyan basin around Chambal Valley have been reported to vary between 1–2547 ppb, 1–558 ppb, 1–181 ppb, 1–37 ppb and 1–32 ppb, respectively with high concentrations around Baran-Jhalawar-Bhanpur-Garot regions (Kumar et al., 2006). The light gaseous hydrocarbon anomalies are coincident with the wrench faults (Kota – Dholpur, Ratlam – Shivpuri, Kannod – Damoh, Son Banspur – Rewa wrench) in the Vindhyan basin, which may provide conducive pathways for the migration of the hydrocarbons towards the near surface soils.  相似文献   

15.
通过密封金管-高压釜体系对珠江口盆地番禺低隆起-白云凹陷北坡恩平组炭质泥岩的干酪根(PY),在24.1 MPa压力、20℃/hr(373.5~526℃)和2℃/h(343~489.2℃)两个升温速率条件下进行热模拟生烃实验,分析气态烃(C1 5)和液态烃(C6 14和C14+)的产率,以及沥青质和残余有机质碳同位素组成。同时与Green River页岩(GR)和Woodford泥岩(WF)的干酪根,分别代表典型的I型和II型干酪根进行对比研究。结果显示PY热演化产物中总油气量明显低于GR和WF干酪根,且气态烃(C1 5)最高产率是液态烃的1.5倍,揭示恩平组炭质泥岩主要以形成气态烃为主。在热演化过程中,有机质成熟度和母质类型是控制油气比的主要因素,气态烃和轻烃的产率比值主要受热演化成熟度的影响。干酪根残余有机质碳同位素和沥青质碳同位素在热演化过程中受有机质成熟度的影响较小,δ13C残余和δ13C沥青质可以间接反映原始母质的特征,为高演化烃源岩油气生成提供依据。  相似文献   

16.
 Incorporation of hydrocarbons (CH4, C2H6, C3H8, C4H10) in cordierite channels was experimentally studied at 700 °C and at pressures from 200 to 1000 MPa, (avoiding recrystallization). The maximum concentrations of hydrocarbons determined by gas chromatographic analysis are CH4=78.3, C2H6=134, C2H4 + C2H6=26, C3H8=28, C4H10=32, C5H12=23, and C6H14=7 × 10−3 wt%). According to IR spectroscopy data, the channel forms of hydrocarbons differ from the forms on the surface. As a result of interactions with the framework oxygen, normal hydrocarbons are converted to saturated oligomers and their fragments. Small amounts of water molecules of the first and second types (up to 0.3 wt%) are formed in the same way. As pressure grows from 200 to 1000 MPa, the total content of structural hydrocarbons is nearly doubled. Special runs on cordierite saturation in mixtures of hydrocarbons with water showed that low contents of hydrocarbons in natural cordierites correspond to their large concentrations in fluid. Received: 7 May 2001 / Accepted: 17 July 2001  相似文献   

17.
Unlike long-term heating in subsiding sedimentary basins, the near-instantaneous thermal maturation of sedimentary organic matter near magmatic intrusions is comparable to artificial thermal maturation in the laboratory in terms of short duration and limited extent. This study investigates chemical and H, C, N, O isotopic changes in high volatile bituminous coal near two Illinois dike contacts and compares observed patterns and trends with data from other published studies and from artificial maturation experiments. Our study pioneers in quantifying isotopically exchangeable hydrogen and measuring the D/H (i.e., 2H/1H) ratio of isotopically non-exchangeable organic hydrogen in kerogen near magmatic contacts. Thermal stress in coal caused a reduction of isotopically exchangeable hydrogen in kerogen from 5% to 6% in unaltered coal to 2-3% at contacts, mostly due to elimination of functional groups (e.g., OH, COOH, NH2). In contrast to all previously published data on D/H in thermally matured organic matter, the more mature kerogen near the two dike contacts is D-depleted, which is attributed to (i) thermal elimination of D-enriched functional groups, and (ii) thermal drying of hydrologically isolated coal prior to the onset of cracking reactions, thereby precluding D-transfer from relatively D-enriched water into kerogen. Maxima in organic nitrogen concentration and in the atomic N/C ratio of kerogen at a distance of ∼2.5 to ∼3.5 m from the thicker dike indicate that reactive N-compounds had been pyrolytically liberated at high temperature closer to the contact, migrated through the coal seam, and recombined with coal kerogen in a zone of lower temperature. The same principle extends to organic carbon, because a strong δ13Ckerogen vs. δ15Nkerogen correlation across 5.5 m of coal adjacent to the thicker dike indicates that coal was functioning as a flow-through reactor along a dynamic thermal gradient facilitating back-reactions between mobile pyrolysis products from the hot zone as they encounter less hot kerogen. Vein and cell filling carbonate is most abundant in highest rank coals where carbonate δ13CVPDB and δ18OVSMOW values are consistent with thermal generation of 13C-depleted and 18O-enriched CO2 from decarboxylation and pyrolysis of organic matter. Lower background concentrations of 13C-enriched carbonate in thermally unaffected coal may be linked to 13C-enrichment in residual CO2 in the process of CO2 reduction via microbial methanogenesis.Our compilation and comparison of available organic H, C, N isotopic findings on magmatic intrusions result in re-assessments of majors factors influencing isotopic shifts in kerogen during magmatic heating. (i) Thermally induced shifts in organic δD values of kerogen are primarily driven by the availability of water or steam. Hydrologic isolation (e.g., near Illinois dikes) results in organic D-depletion in kerogen, whereas more common hydrologic connectivity results in organic D-enrichment. (ii) Shifts in kerogen (or coal) δ13C and δ15N values are typically small and may follow sinusoidal patterns over short distances from magmatic contacts. Laterally limited sampling strategies may thus result in misleading and non-representative data. (iii) Fluid transport of chemically active, mobile carbon and nitrogen species and recombination reactions with kerogen result in isotopic changes in kerogen that are unrelated to the original, autochthonous part of kerogen.  相似文献   

18.
The enclosed organic matter chiefly releases lower carbon-number n-alkanes under high temperature and high pressure,while the kerogen mainly produces higher carbon-number n-alkanes.The rsidual hydrocarbons generated by both kerogen and enclosed organic matter in the Tieling limestone contain abundant tricyclic terpanes,pentacyclic triterpanes and steranes,but the contents of tetracyclic terpanes and 25-norhopane are lower.The residual enclosed orgainc matter shows the same distribution characteristics of n-alkanes,steranes and terpanes as that of the original bitumaen A,i.e.,the higher contents of triterpanes and tetracyclic terpanes,the higher ratios of 25-norhopanes over regular hopanes and markedly degraded steranes.By comparing the residual hydrocarbon.residual enclosed orgainc matter and original enclosed orgainc matter.it can be concluded that steranes and terpanes in the residual hydrocarbons are produced mainly by the kerogen and subordinately by the residual enclosed organic matter,the steranes and terpanes do not enter into the residual enclosed organic matter,and the thermal evolution of the residual enclosed organic matter maintains its unique character.Furthermore,pressure retards the pyrolysis of higher carbon-number alkanes and influences the isomerization ratios of C29-steranes,making 20S/(20S 20R) lower under the higher pressure than that under lower pressure,Higher pressure retards the thermal evolution of organic matter.  相似文献   

19.
Petroleum hydrocarbons are formed by breakdown of kerogen preserved in source rocks throughout the process of catagenesis. This process is accompanied by free radical generation in kerogen. The availability of measuring free radicals in kerogen using ESR to deduce a maturation estimation of potential source rocks has been hindered due to the presence of the solvent-extractable organic molecules (SEOM) trapped within the kerogen matrix. Spin concentration (Ns) of the kerogen treated with pyridine (KPy) represents the paramagnetic centers of the kerogen matrix itself and provides a potential parameter to evaluate kerogen maturation.  相似文献   

20.
This study elucidates the geothermal influence of a salt dome on the diagenesis of organic matter present in sedimentary sequences directly overlying the salt strata. Despite similarities in geological setting, geochemical characteristics in sedimentary column and proximity of location (～3 km), the exploratory wells Adolphus 2-k-41 and D-50 drilled on the crest and flank of a salt dome respectively, show considerable differences in the quantitative and qualitative distribution of hydrocarbons. The well drilled on the crest of the salt dome tested oil of 31°APl gravity. The concentrations of gaseous (C1-C4) and heavy (C15+) hydrocarbons of this well were several times higher than those found in the corresponding sequences of a flank well. The coloration studies of isolated kerogen and gas chromatographic investigations of hydrocarbons suggest that the organic matter present in Adolphus 2-k-41 has undergone a greater degree of thermal alteration than that of D-50. The heat radiating from the salt strata is believed to be responsible for the early diagenesis of the organic matter.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号