共查询到20条相似文献，搜索用时 15 毫秒
1.
Hong-Jian Liao Li-Jun Su Wu-Chuan Pu Jian-Hua Yin 《Marine Georesources & Geotechnology》2003,21(3):183-200
A kind of diatomaceous soft rock and its constitutive model are studied in this article. Based on Yin and Graham's (1999) 3-D elastic viscoplastic constitutive model, the formulation under a triaxial stress state is established, and it is used to simulate the time-dependent stress-strain behavior and effective stress path of consolidated undrained triaxial tests of both normally consolidated and overconsolidated soft rock. The comparison between the model predictions and measured results shows that their agreement is good. This demonstrates that the constitutive equation established here can be used to simulate the time-dependent stress-strain behavior of the soft rock under triaxial stress condition. 相似文献
2.
Wang Nianxiang Wei Rulong Engineer Geotechnical Engineering Department Nanjing Hydraulic Research Institute Nanjing Prof. Senior Engineer Geotechnical Engineering Department Nanjing Hydraulic Research Institute Nanjing 《中国海洋工程》1994,(2)
-A nonlinear model for the stress-strain behaviour of normally consolidated clays is presented based on the experimental results. It is indicated that the volume strain under pure shear is a power function of stress ratio and the normalized stress-strain curve is a standard hyperbola. According to the model, the coefficient of pore pressure induced by shear stress and the critical stress ratio which governs the influence of the negative dilatancy are suggested. It is shown by some triaxial tests that the proposed model can be used to study the negative dilatancy and to describe the stress-strain-pore pressure adequately for soft clays. 相似文献
3.
4.
Wisam R. Muttashar 《Marine Georesources & Geotechnology》2020,38(8):896-910
AbstractThe mechanical response of a sediment to an applied stress is significantly affected by variations of material properties, state conditions, and stress states. These stress state and conditions are utilized to infer input parameters for advanced soil constitutive models. Parameters such as void ratio and effective stresses have been readily inferred from shear-wave velocities under low-strain conditions. Thus, this research aimed to develop a shear-wave velocity-based constitutive model within a critical state soil mechanics framework to predict the undrained triaxial behavior of fine-grained sediments. Laboratory tests were performed for sediment samples ranging from silt-predominant to clay-predominant sediments. As result, a new two-term power function was developed that determined mean effective stress as a function of shear-wave velocity. By virtue of this new power function, the Original Cam Clay and Modified Cam Clay critical state models were adapted to estimate the stress-strain behavior and stress paths under undrained conditions, in terms of shear velocity. In addition, correlations were developed using the state and material properties to predict the input model parameters. The developed correlations allow broad application of the proposed framework to different sediment types in which clay and silt are the dominant deposits. 相似文献
5.
An elastoplastic damage constitutive model to simulate nonlinear behavior of concrete is presented. Similar to traditional plastic theory, the irreversible deformation is modeled in effective stress space. In order to better describe different stiffness degradation mechanisms of concrete under tensile and compressive loading conditions, two damage variables, i.e., tension and compression are introduced, to quantitatively evaluate the degree of deterioration of concrete structure. The rate dependent behavior is taken into account, and this model is derived firmly in the framework of irreversible thermodynamics. Fully implicit backward-Euler algorithm is suggested to perform constitutive integration. Numerical results of the model accord well with the test results for specimens under uniaxial tension and compression, biaxial loading and triaxial loading. Failure processes of double-edge-notched (DEN) specimen are also simulated to further validate the proposed model. 相似文献
6.
In this study, Lade's double-surface work-hardening constitutive model was adopted which uses the elasto-plasticity model as a basic conceptual framework. The model can analyze work hardening and work softening of nonlinear stress-strain behavior, and is regarded as superior to other elasto-plasticity constitutive models in terms of estimation. In the double-surface work-hardening constitutive model, 14 soil parameters are needed to estimate soil behaviors. To determine them, laboratory tests—isotropical consolidation test and conventional compression test—were conducted. Determining of soil parameters is highly complicated and time-consuming; randomness cannot be ruled out in determining parameters that are sensitive to stress-strain estimation, and error may occur. For this reason, a linear and nonlinear regression analysis was used to determine soil parameters. In estimation of undrained behavior, the estimated stress-strain behavior based on the two constitutive models largely overlapped with the test results. However, in estimating drained behavior, the outcome of the two models and the test results were mostly the same, but between the two models, the double-surface work-hardening constitutive model had a sharper slope in initial stress state, and a smaller maximum deviatoric stress. 相似文献
7.
The paper presents a constitutive model to describe undrained cyclic stress-strain responses of soft clays based on the equivalent visco-elastic and creep theories. The hysteretic and nonlinear stress-strain responses of soft clays are described using the equivalent visco-elastic relationship and variations of the cyclic modulus and the damping ratio with the octahedral shear strain, respectively in the model. The cyclic accumulative strain is described using the Mises creeping potential function and the associated flow rule. The method determining the model parameters is given by static and cyclic triaxial tests. The finite element method to analyze deformation of anchor foundation in soft clay under static and cyclic loads is developed based on the model. For the method, a cyclic loading time history is divided into a series of incremental loading sub-processes which include one load cycle at least. The cyclic stress-strain responses of soil elements at any time are not tracked in detail and determined by the equivalent visco-elastic calculations for every loading sub-process. The accumulative deformation of anchor foundations is calculated using the initial strain algorithm. The method has been implemented in ABAQUS Software by developing interface programs. Model tests of the suction anchors are conducted and predicted using the method. Comparisons of predicted and model test results show that the method can be used to evaluate cyclic stability and reveal the failure process and mechanism of anchor foundations by analyzing deformation time-histories. 相似文献
8.
Cumulative Deformation of Soft Clay Under Cyclic Loading 总被引：2，自引：1，他引：2
Yan Shuwang Yan Chi Zhang Jianguo Professor Tianjin University Tianjin Lecturer Tianjin University Tianjin 《中国海洋工程》1993,(3)
Reconstituted specimens are prepared by means of vacuum preloading. Both static and cyclic triaxial tests are carried out, with the specimens consolidated under different principal stress ratios. A finite element method is put forward for calculating the cumulative deformation of soft clay under cyclic loading. 相似文献
9.
Principal stress axes rotation influences the stress-strain behavior of sand under wave loading. A constitutive model for sand, which considers principal stress orientation and is based on generalized ... 相似文献
10.
The post-cyclic behavior of biogenic carbonate sand was evaluated using cyclic triaxial testing through a stress control method under different confining pressures between 50 to 600 kPa. The testing program included a series of isotropically and anisotropically consolidated, undrained triaxial compression and extension tests on samples of remolded calcareous Bushehr sand. Grading analyses (before and after each test) were used to examine the influence of particle breakage on post-cyclic behavior of Bushehr sand. The particle breakage commonly occurred in these soils even in lower values of confining pressure, yet there was not a clear correlation between the post-cyclic responses and particle breakage. Based on the present study, a concept is suggested for post-cyclic behavior of carbonate sand. It was observed that post-cyclic strength has a good correlation with cyclic stress ratio, type of consolidation, and value of residual cyclic strain. For all specimens, it is clear that the post-cyclic strength is greater than monotonic strength, irrespective of confining pressure and relative density. 相似文献
11.
AbstractHollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand. 相似文献
12.
The change in strength and deformation behavior of a typical marine clay deposit formed under shallow water is presented and discussed for the conditions of changing water table. This is a costal marine clay deposit with moderate carbonates along the east coast of India. The soil samples were taken from tidal flats where the sea had receded some time back, and the behavior of this deposit had been studied for the conditions of 1976, with high water table, and for the conditions of 2001, with depleted water table. Undisturbed soil samples were taken from sheeted open test pits. Standard consolidation and triaxial shear tests were conducted. Consolidation tests conducted on the samples taken for 1976 conditions with high water contents indicate that cementation effect are erased out under moderate stresses. Beyond this stress range, it behaves like soft, normally consolidated clay. In contrast, the results obtained from samples taken during 2001, with depleted water table, clearly indicate that the soil behaves like an over-consolidated one, and the improvement in the system is due to the chemical bonding and desiccation. 相似文献
13.
S. G. Chung K. Nagendra Prasad T. S. Nagaraj J. G. Chung K. Y. Jo 《Marine Georesources & Geotechnology》2004,22(1):1-20
It Naturally cemented soft clays have components of strength and stiffness, which cannot be accounted for by classical soil mechanics (Leroueil and Vaughan 1990). This stems from the influence of structure caused by cementation due to environmental factors. It is necessary to evaluate the cementation bond strength at preyield and postyield stress levels of loading, to understand comprehensively the observed response from micromechanic considerations. This helps to better understand and evolve approaches to model the constitutive behavior in a consistent manner, according to the physical phenomenon of formation of cementation as an additional component to what is otherwise normally regarded as frictional behavior arising only from particulate nature of clays. Comparing the behavior of deep deposits of Pusan soft clays under stress with corresponding response of the same clay in its remolded state, it has been possible to take into account particulate and nonparticulate responses. The evolution of cementation bonding is modeled for different Pusan clays with the yield stress in oedometer compression as a normalizing parameter for obtaining the generalized relationship of cementation bonding with increase in stress. The already established model for determining the remolded behavior is appropriately modified to assess the behavior influenced by cementation. The model proposed consists of parameters, which are determined in routine investigations. 相似文献
14.
S. G. CHUNG K. NAGENDRA PRASAD T. S. NAGARAJ J. G. CHUNG K. Y. JO 《Marine Georesources & Geotechnology》2013,31(1-2):1-20
It Naturally cemented soft clays have components of strength and stiffness, which cannot be accounted for by classical soil mechanics (Leroueil and Vaughan 1990). This stems from the influence of structure caused by cementation due to environmental factors. It is necessary to evaluate the cementation bond strength at preyield and postyield stress levels of loading, to understand comprehensively the observed response from micromechanic considerations. This helps to better understand and evolve approaches to model the constitutive behavior in a consistent manner, according to the physical phenomenon of formation of cementation as an additional component to what is otherwise normally regarded as frictional behavior arising only from particulate nature of clays. Comparing the behavior of deep deposits of Pusan soft clays under stress with corresponding response of the same clay in its remolded state, it has been possible to take into account particulate and nonparticulate responses. The evolution of cementation bonding is modeled for different Pusan clays with the yield stress in oedometer compression as a normalizing parameter for obtaining the generalized relationship of cementation bonding with increase in stress. The already established model for determining the remolded behavior is appropriately modified to assess the behavior influenced by cementation. The model proposed consists of parameters, which are determined in routine investigations. 相似文献
15.
Based on the analysis of cyclic triaxial test for the South-Sea sand, a comprehensive normalized model of soil stress-strain relationship is presented herein, which includes effects of not only initial stress states but also loading cycles. Consequently, a pseudo-static procedure to analyse the deformation behavior of foundations is suggested. Example of calculations shows that the suggested procedure is convenient in application. 相似文献
16.
针对深海玄武岩岩芯样品在高围压下难以破碎获得的问题,理论分析了金刚石与岩石的相互作用。采用单轴与三轴压缩实验,获得了模拟深海玄武岩的力学参数;基于颗粒流理论,建立了深海玄武岩线性平行黏结颗粒流数值模型,数值模拟高围压下金刚石颗粒破碎玄武岩的过程,获得了金刚石与玄武岩相互作用的动态力学响应规律,初步阐明金刚石破碎玄武岩机理。研究表明,玄武岩颗粒间黏接破坏主要为拉伸失效,玄武岩与金刚石接触力体现为周期应力,玄武岩产生间歇式裂隙扩散。理论分析与仿真结果基本吻合,表明建模与仿真的正确性,为深海便携式取芯钻机设计提供了理论基础与技术依据。 相似文献
17.
Sheng-Feng Zou Xin-Yu Xie Zhong-Jin Wang Heng-Yu Wang 《Marine Georesources & Geotechnology》2013,31(6):660-670
AbstractThis paper presents a novel elasto-viscoplastic constitutive formulation based on the isotache concepts and the Nishihara model. Incorporating a novel viscoelastic body to include the delay elastic deformation of marine soft clays under the external load, the proposed model is used to evaluate the theories of consolidation-creep coupling, strain rate dependency and stress relaxation of saturated marine soft clays, and hence, the methodology used to determine the parameters of the model is discussed. Ningbo marine soft clay is selected as an example to interpret the determination of the model parameters on a field scale. A series of conventional oedometer tests are conducted as well. Eventually, we utilize the model to simulate several kinds of rheological tests, including one-dimensional (1-D) long-term compression tests on Ningbo marine soft clays, 1-D constant rate of strain (CRS) tests on Batiscan clays and 1-D stress relaxation tests on Hong Kong marine deposits. These findings indicate good agreement between the computational and experimental results, suggesting the given model can provide reliable forecasts for the rheological characteristics of marine soft clays. 相似文献
18.
A testing program was initiated to determine the stress-strain and strength behavior of two very different marine sands (a calcareous sediment from South Australia and a siliceous sediment from the United Kingdom) at elevated confining pressures. The testing matrix consisted of a series of isotropically consolidated, undrained (CIU) and drained (CID), triaxial compression tests on samples of naturally deposited calcareous and siliceous sediment and remolded calcareous sediment. It was found that the calcareous samples displayed little cemented behavior during shear. For tests conducted at pressures up to 1.5 MPa, a significant amount of particle crushing occurred in the calcareous samples but not in the siliceous samples. Particle degradation and reorientation facilitates transitions from dilative to contractive behavior with increases in confining stress. The calcareous sediment exhibited contractive behavior at confining pressures above approximately 500 kPa and the siliceous sediment remained dilative at stresses up to 1 MPa during undrained loading. Comparison with data collected by the University of Sydney (CID tests with confining pressures up to 60 MPa) showed that most of the variations in strength behavior occurred within the low stress range (up to 2 MPa) tests conducted at URI. This was evident in the friction angle data and in the reloading Young's modulus data. 相似文献
19.
Settlement Analysis for An Embankment Considering Visco-Elasto-Plastic Characteristics 总被引：1，自引：0，他引：1
SHI Jianyong 《中国海洋工程》2000,14(3):349-360
—In the paper.a visco-elasto-plastic constitutive model and a method for determining modelparameters for soft clay are presented.In this model total strain of soft clay is assumed to be divided intothree parts:instantaneous elastic.visco-elastic and visco-plastic.The characteristics of instantaneous andvisco-elastic deformation of soft clay are simulated by Merchant's model.the plastic is by a model withtwo yield surfaces.And related constitutive equation is conducted,A number of stress-controlled triaxialtests are performed to calculated the model parameters The visco-elasto-plastic model is used for analysisof the displacement of an embankment on soft ground by use of three-dimensional finite element method.The predicted settlements agree well with the measured data.It is indicated that the viscous characteristicsshould be taken into account in deformation analysis for soft clay. 相似文献
20.
—Presented is the numerical analysis of settlements of soft soil by a 2-D dynamic effective stressFEM method.The model based on the results of cyclic triaxial tests on the reconstituted soft Ariake clay isused to predict the wave induced excess pore water pressure and residual strain of soft clay.The settle-ments of two types of breakwaters on the soft clay under ocean wave load,a low embankment subjected totraffic load and the tunnel surrounded by soft clay in Shanghai subjected to locomotive load are calculatedas examples. 相似文献