首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Terrestrial Laser Scanners (TLS) provide a non‐contact method to measure soil microtopography of relatively large surface areas. The appropriateness of the technology in relatation to the derived Digital Elevation Models (DEM) however has not been reported. The suitability of TLS for soil microtopography measurements was tested on‐field for three large soil surface areas in agricultural fields. The acquired point clouds were filtered with a custom cloud import algorithm, and converted into digital elevation models (DEM) of different resolutions. To assess DEM quality, point clouds measured from different viewpoints were statistically compared. The statistical fit between point clouds from different viewpoints depends on spatial resolution of the DEM. The best results were obtained at the higher resolutions (0.02 to 0.04 cm), where less than 5 % of the grid cells showed significant differences between one viewpoint and the next (p < 0.01). Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

2.
Quantifying the extent of soil erosion at a fine spatial resolution can be time consuming and costly; however, proximal remote sensing approaches to collect topographic data present an emerging alternative for quantifying soil volumes lost via erosion. Herein we compare terrestrial laser scanning (TLS), and both unmanned aerial vehicle (UAV) and ground photography (GP) structure‐from‐motion (SfM) derived topography. We compare the cost‐effectiveness and accuracy of both SfM techniques to TLS for erosion gully surveying in upland landscapes, treating TLS as a benchmark. Further, we quantify volumetric soil loss estimates from upland gullies using digital surface models derived by each technique and subtracted from an interpolated pre‐erosion surface. Soil loss estimates from UAV and GP SfM reconstructions were comparable to those from TLS, whereby the slopes of the relationship between all three techniques were not significantly different from 1:1 line. Only for the TLS to GP comparison was the intercept significantly different from zero, showing that GP is more capable of measuring the volumes of very small erosion features. In terms of cost‐effectiveness in data collection and processing time, both UAV and GP were comparable with the TLS on a per‐site basis (13.4 and 8.2 person‐hours versus 13.4 for TLS); however, GP was less suitable for surveying larger areas (127 person‐hours per ha?1 versus 4.5 for UAV and 3.9 for TLS). Annual repeat surveys using GP were capable of detecting mean vertical erosion change on peaty soils. These first published estimates of whole gully erosion rates (0.077 m a?1) suggest that combined erosion rates on gully floors and walls are around three times the value of previous estimates, which largely characterize wind and rainsplash erosion of gully walls. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

3.
In the year 2007, enhanced rockfall activity was observed within the scarp of a 500 BP rockslide in the Reintal catchment (Northern Calcareous Alps, Germany); the largest of a series of events took place in August, when almost 50000 m³ of rock were detached from the subvertical rock face and deposited on a talus cone. In this case study, we focus on three aspects of rockfall research: first, we compile detailed geomorphological and geotechnical findings to explain the causes of the recent events. The results of laboratory tests and stability estimations suggest that rockfall activity will persist in the future as the old rockslide scarp still contains unstable rock masses. Second, we use digital elevation data from a pre‐event airborne LiDAR survey (ALS) and post‐event terrestrial laserscanning (TLS) to quantify landform changes and the mass balance of the rockfall event(s). The widespread availability of ALS elevation data provides a good opportunity to quantify fresh events using a comparatively inexpensive TLS survey; this approach is complicated by uncertainties resulting from the difficult coregistration of ALS and TLS data and the specific geometric problems in steep (ALS) and flat (TLS) terrain; it is therefore limited to at least medium‐sized events. Third, the event(s) is simulated using the results of the LiDAR surveys and a modified GIS‐based rockfall model in order to test its capability of predicting the extent and the spatial distribution of deposition on the talus cone. Results show that the model generally reproduces the process domain and the spatial distribution of topographic changes but frequently under‐ and over‐estimates deposition heights. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

4.
Terrestrial laser scanning is the current technique of choice for acquiring high resolution topographic data at the site scale (i.e. over tens to hundreds of metres), for accurate volume measurements or process modelling. However, in regions of complex topography with multiple local horizons, restricted lines of sight significantly hinder use of such tripod‐based instruments by requiring multiple setups to achieve full coverage of the area. We demonstrate a novel hand‐held mobile laser scanning technique that offers particular promise for site‐scale topographic surveys of complex environments. To carry out a survey, the hand‐held mobile laser scanner (HMLS) is walked across a site, mapping around the surveyor continuously en route. We assess the accuracy of HMLS data by comparing survey results from an eroding coastal cliff site with those acquired by a state‐of‐the‐art terrestrial laser scanner (TLS) and also with the results of a photo‐survey, processed by structure from motion and multi‐view stereo (SfM‐MVS) algorithms. HMLS data are shown to have a root mean square (RMS) difference to the benchmark TLS data of 20 mm, not dissimilar to that of the SfM‐MVS survey (18 mm). The efficiency of the HMLS system in complex terrain is demonstrated by acquiring topographic data covering ~780 m2 of salt‐marsh gullies, with a mean point spacing of 4.4 cm, in approximately six minutes. We estimate that HMLS surveying of gullies is approximately 40 times faster than using a TLS and six times faster than using SfM‐MVS. © 2013 The Authors. Earth Surface Processes and Landforms Published by John Wiley & Sons Ltd.  相似文献   

5.
Long‐range terrestrial laser scanning (TLS) is an emerging method for the monitoring of alpine slopes in the vicinity of infrastructure. Nevertheless, deformation monitoring of alpine natural terrain is difficult and becomes even more challenging with larger scan distances. In this study we present approaches for the handling of spatially variable measurement uncertainties in the context of geomorphological change detection using multi‐temporal data sets. A robust distance measurement is developed, which deals with surface roughness and areas of lower point densities. The level of detection (LOD), i.e. the threshold distinguishing between real surface change and data noise, is based on a confidence interval considering the spatial variability of TLS errors caused by large laser footprints, low incidence angles and surface roughness. Spatially variable positional uncertainties are modelled for each point according to its range and the object geometry hit. The local point cloud roughness is estimated in the distance calculation process from the variance of least‐squares fitted planes. Distance calculation and LOD assessment are applied in two study areas in the Eastern Alps (Austria) using multi‐temporal laser scanning data sets of slopes surrounding reservoir lakes. At Finstertal, two TLS point clouds of high alpine terrain and scanned from ranges between 300 and 1800 m are compared. At Gepatsch, the comparison is done between an airborne laser scanning (ALS) and a TLS point cloud of a vegetated mountain slope scanned from ranges between 600 and 3600 m. Although these data sets feature different conditions regarding the scan setup and the surface conditions, the presented approach makes it possible to reliably analyse the geomorphological activity. This includes the automatic detection of rock glacier movement, rockfall and debris slides, even in areas where a difference in vegetation cover could be observed. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

6.
Drainage channels are an integral part of agricultural landscapes, and their impact on catchment hydrology is strongly recognized. In cultivated and urbanized floodplains, channels have always played a key role in flood protection, land reclamation, and irrigation. Bank erosion is a critical issue in channels. Neglecting this process, especially during flood events, can result in underestimation of the risk in flood‐prone areas. The main aim of this work is to consider a low‐cost methodology for the analysis of bank erosion in agricultural drainage networks, and in particular for the estimation of the volumes of eroded and deposited material. A case study located in the Veneto floodplain was selected. The research is based on high‐resolution topographic data obtained by an emerging low‐cost photogrammetric method (structure‐from‐motion or SfM), and results are compared to terrestrial laser scanning (TLS) data. For the SfM analysis, extensive photosets were obtained using two standalone reflex digital cameras and an iPhone5® built‐in camera. Three digital elevation models (DEMs) were extracted at the resolution of 0.1 m using SfM and were compared with the ones derived by TLS. Using the different DEMs, the eroded areas were then identified using a feature extraction technique based on the topographic parameter Roughness Index (RI). DEMs derived from SfM were effective for both detecting erosion areas and estimating quantitatively the deposition and erosion volumes. Our results underlined how smartphones with high‐resolution built‐in cameras can be competitive instruments for obtaining suitable data for topography analysis and Earth surface monitoring. This methodology could be potentially very useful for farmers and/or technicians for post‐event field surveys to support flood risk management. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

7.
To quantify landscape change resulting from processes of erosion and deposition and to establish spatially distributed sediment budgets, ‘models of change’ can be established from a time series of digital elevation models (DEMs). However, resolution effects and measurement errors in DEMs may propagate to these models. This study aimed to evaluate and to modify remotely‐sensed DEMs for an improved quantification of initial sediment mass changes in an artificially‐created catchment. DEMs were constructed from photogrammetry‐based, airborne (ALS) and ground‐based laser scanning (TLS) data. Regions of differing morphological characteristics and vegetation cover were delineated. Three‐dimensional (3D) models of volume change were established and mass change was derived from these models. DEMs were modified region‐by‐region for rill, interrill and alluvial areas, based on logical and hydro‐geomorphological principles. Additional DEMs were constructed by combining multi‐source, modified data. Models were evaluated by comparison with d‐GPS reference data and by considering sediment budget plausibility. Comprehensive evaluation showed that DEM usability depends on a relation between the technique used to obtain elevation data, surface morphology and vegetation cover characteristics. Photogrammetry‐based DEMs were suited to quantification of change in interrill areas but strongly underestimated surface lowering in erosion rills. TLS DEMs were best suited to rill areas, while ALS DEMs performed best in vegetation‐covered alluvial areas. Agreement with reference data and budget plausibility were improved by modifications to photogrammetry‐ and TLS‐based DEMs. Results suggest that artefacts in DEMs can be reduced and hydro‐geomorphic surface structures can be better represented by applying region‐specific modifications. Photogrammetry‐based DEMs can be improved by combining higher and lower resolution data in defined structural units and applying modifications based on principles given by characteristic hydro‐geomorphic evolution. Results of the critical comparative evaluation of remotely‐sensed elevation data can help to better interpret DEM‐based quantifications of earth‐surface processes. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

8.
The grain‐scale morphology of fluvial sediments is an important control on the character and dynamics of river systems; however current understanding of its role is limited by the difficulties of robustly quantifying field surface morphology. Terrestrial Laser Scanning (TLS) offers a new methodology for the rapid acquisition of high‐resolution and high‐precision surface elevation data from in situ sediments. To date, most environmental and fluvial applications of TLS have focused on large‐scale systems, capturing macroscale morphologies. Application of this new technology at scales necessary to characterize the complexity of grain‐scale fluvial sediments therefore requires a robust assessment of the quality and sources of errors in close‐range TLS data. This paper describes both laboratory and field experiments designed to evaluate close‐range TLS for sedimentological applications and to develop protocols for data acquisition. In the former, controlled experiments comprising high‐resolution scans of white, grey and black planes and a sphere were used to quantify the magnitude and source of three‐dimensional (3D) point errors resulting from a combination of surface geometry, reflectivity effects and inherent instrument precision. Subsequently, a methodology for the collection and processing of grain‐scale TLS data is described through an application to a coarse grained gravel system, the River Feshie (D50 32 to 63 mm). This stepwise strategy incorporates averaging repeat scans and filtering scan artefact and non‐surface points using local 3D search algorithms. The sensitivity of the results to the filter parameter values are assessed by careful internal validation of Digital Terrain Models (DTMs) created from the resulting point cloud data. The transferability of this methodology is assessed through application to a second river, Bury Green Brook, dominated by finer gravel (D50 18 to 33 mm). The factor limiting the resolution of DTMs created from this second dataset was found to be the relative sizes of the laser footprint and smallest grains. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

9.
In the last decade advances in surveying technology have opened up the possibility of representing topography and monitoring surface changes over experimental plots (<10 m2) in high resolution (~103 points m‐1). Yet the representativeness of these small plots is limited. With ‘Structure‐from‐Motion’ (SfM) and ‘Multi‐View Stereo’ (MVS) techniques now becoming part of the geomorphologist's toolkit, there is potential to expand further the scale at which we characterise topography and monitor geomorphic change morphometrically. Moving beyond previous plot‐scale work using Terrestrial Laser Scanning (TLS) surveys, this paper validates robustly a number of SfM‐MVS surveys against total station and extensive TLS data at three nested scales: plots (<30 m2) within a small catchment (4710 m2) within an eroding marl badland landscape (~1 km2). SfM surveys from a number of platforms are evaluated based on: (i) topography; (ii) sub‐grid roughness; and (iii) change‐detection capabilities at an annual scale. Oblique ground‐based images can provide a high‐quality surface equivalent to TLS at the plot scale, but become unreliable over larger areas of complex terrain. Degradation of surface quality with range is observed clearly for SfM models derived from aerial imagery. Recently modelled ‘doming’ effects from the use of vertical imagery are proven empirically as a piloted gyrocopter survey at 50m altitude with convergent off‐nadir imagery provided higher quality data than an Unmanned Aerial Vehicle (UAV) flying at the same height and collecting vertical imagery. For soil erosion monitoring, SfM can provide data comparable with TLS only from small survey ranges (~5 m) and is best limited to survey ranges ~10–20 m. Synthesis of these results with existing validation studies shows a clear degradation of root‐mean squared error (RMSE) with survey range, with a median ratio between RMSE and survey range of 1:639, and highlights the effect of the validation method (e.g. point‐cloud or raster‐based) on the estimated quality. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

10.
Different high‐resolution techniques can be employed to obtain information about the three‐dimensional (3D) surface of glaciers. This is typically carried out using efficient, but also expensive and logistically demanding, light detection and ranging (LiDAR) technologies, such as airborne scanners and terrestrial laser scanners. Recent technological improvements in the field of image analysis and computer vision have prompted the development of a low‐cost photogrammetric approach, which is referred to as ‘structure‐from‐motion’ (SfM). Combined with dense image‐matching algorithms, this method has become competitive for the production of high‐quality 3D models. However, several issues typical of this approach should be considered for application in glacial environments. In particular, the surface morphology, the different substrata, the occurrence of sharp contrast from solar shadows and the variable distance from the camera positions can negatively affect the image texture, and reduce the possibility of obtaining a reliable point cloud from the images. The objective of this study is to test the structure‐from‐motion multi view stereo (SfM‐MVS) approach in a small debris‐covered glacier located in the eastern Italian Alps, using a consumer‐grade reflex camera and the computer vision‐based software PhotoScan. The quality of the 3D models produced by the SfM‐MVS process was assessed via the comparison with digital terrain models obtained from terrestrial laser scanning (TLS) surveys that were performed at the same epochs. The effect of different terrain gradients and different substrata (debris, snow and firn) was also evaluated in terms of the accuracy of the reconstruction by SfM‐MVS versus TLS. Our results show that the quality of this new photogrammetric approach is similar to the quality of TLS and that point cloud densities are comparable or even higher compared with TLS. However, special care should be taken while planning the SfM survey geometry, to optimize the 3D model quality and spatial coverage. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

11.
Soil microtopography is a property of critical importance in many earth surface processes but is often difficult to quantify. Advances in computer vision technologies have made image‐based three‐dimensional (3D) reconstruction or Structure‐from‐Motion (SfM) available to many scientists as a low cost alternative to laser‐based systems such as terrestrial laser scanning (TLS). While the performance of SfM at acquiring soil surface microtopography has been extensively compared to that of TLS on bare surfaces, little is known about the impact of vegetation on reconstruction performance. This article evaluates the performance of SfM and TLS technologies at reconstructing soil microtopography on 6 m × 2 m erosion plots with vegetation cover ranging from 0% to 77%. Results show that soil surface occlusion by vegetation was more pronounced with TLS compared to SfM, a consequence of the single viewpoint laser scanning strategy adopted in this study. On the bare soil surface, elevation values estimated with SfM were within 5 mm of those from TLS although long distance deformations were observed with the former technology. As vegetation cover increased, agreement between SfM and TLS slightly degraded but was significantly affected beyond 53% of ground cover. Detailed semivariogram analysis on meter‐square‐scale surface patches showed that TLS and SfM surfaces were very similar even on highly vegetated plots but with fine scale details and the dynamic elevation range smoothed out with SfM. Errors in the TLS data were mainly caused by the distance measurement function of the instrument especially at the fringe of occlusion regions where the laser beam intersected foreground and background features simultaneously. From this study, we conclude that a realistic approach to digitizing soil surface microtopography in field conditions can be implemented by combining strengths of the image‐based method (simplicity and effectiveness at reconstructing soil surface under sparse vegetation) with the high accuracy of TLS‐like technologies. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

12.
We test the acquisition of high‐resolution topographic and terrain data using hand‐held smartphone technology, where the acquired images can be processed using technology freely available to the research community. This is achieved by evaluating the quality of digital terrain models (DTM) of a river bank and an Alpine alluvial fan generated with a fully automated, free‐to‐use, structure‐from‐motion package and a smartphone integrated camera (5 megapixels) with terrestrial laser scanning (TLS) data used to provide a benchmark. To evaluate this approach a 16.2‐megapixel digital camera and an established, commercial, close‐range and semi‐automated software are also employed, and the product of the four combinations of the two types of cameras and software are compared. Results for the river bank survey demonstrate that centimetre‐precision DTMs can be achieved at close range (10 m or less), using a smartphone camera and a fully automated package. Results improve to sub‐centimetre precision with either higher‐resolution images or by applying specific post‐processing techniques to the smartphone DTMs. Application to an entire Alpine alluvial fan system shows the degradation of precision scales linearly with image scale, but that (i) the expected level of precision remains and (ii) difficulties in separating vegetation and sediment cover within the results are similar to those typically found when using other photo‐based techniques and laser scanning systems. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

13.
Acquiring high resolution topographic data of natural gravel surfaces is technically demanding in locations where the bed is not exposed at low water stages. Often the most geomorphologically active surfaces are permanently submerged. Gravel beds are spatially variable and measurement of their detailed structure and particle sizes is essential for understanding the interaction of bed roughness with near‐bed flow hydraulics, sediment entrainment, transport and deposition processes, as well as providing insights into the ecological responses to these processes. This paper presents patch‐scale laboratory and field experiments to demonstrate that through‐water terrestrial laser scanning (TLS) has the potential to provide high resolution digital elevation models of submerged gravel beds with enough detail to depict individual grains and small‐scale forms. The resulting point cloud data requires correction for refraction before registration. Preliminary validation shows that patch‐scale TLS through 200 mm of water introduces a mean error of less than 5 mm under ideal conditions. Point precision is not adversely affected by the water column. The resulting DEMs can be embedded seamlessly within larger sub‐aerial reach‐scale surveys and can be acquired alongside flow measurements to examine the effects of three‐dimensional surface geometry on turbulent flow fields and their interaction with instream ecology dynamics. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

14.
Tephra fallout from the 2011 Grímsvötn eruption onto Svínafellsjökull, Iceland, created an ice‐ash landscape of a type that is rarely studied but is nevertheless common in glacio‐volcanic regions. We used terrestrial laser scanning (TLS) to measure ice surface topography and absorption at high spatial resolution, confirming ablation rates either reduce or increase under thick (insulating) and thin (reduced albedo) ash deposits, respectively. Fourier transform analysis of the TLS data identified that a three‐fold increase in aerodynamic roughness was attributable to an increase in larger (> 0·2 m) surface features. Moreover, TLS measurements revealed the importance of ash redistribution by meltwater in generating differential melting which modifies roughness and ash patchiness, such that the net effect of these spatial ash–ice feedbacks was to reduce ablation rates by up to 59%. The modulating effects of these previously undocumented feedbacks on ablation rates are, therefore, significant and must be correctly parameterized if ash‐covered glacier mass balances are to be predicted correctly. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

15.
We report a methodology for reconstructing the daily snow depth distribution at high spatial resolution in a small Pyrenean catchment using time‐lapse photographs and snow depletion rates derived from an on‐site measuring meteorological station. The results were compared with the observed snow depth distribution, determined on a number of separate occasions using a terrestrial laser scanner (TLS). The time‐lapse photographs were projected onto a digital elevation model of the study site, and converted into snow presence/absence information. The melt‐out date (MOD; first occurrence of melt out after peak snow accumulation) was obtained from the projected photograph series. Commencing the backward reconstruction for each grid cell at the MOD, the method uses simulated snow depth depletion rates using a temperature index approach, which are extrapolated to the grid cells of the domain to arrive at the snow distribution of the previous day. Two variants of the reconstruction techniques were applied (1) using a spatially constant degree day factor (DDF) for calculating the daily expected snow depth depletion rate, and (2) allowing a spatially distributed DDF calculated from two consecutive TLS acquisitions compared to the snow depth depletion rate observed at the meteorological station. Validation revealed that both methods performed well (average R2 = 0.68; standard RMSE = 0.58), with better results obtained from the spatially distributed approach. Nevertheless, the spatially corrected DDF reconstruction, which requires TLS data, suggests that the constant DDF approach is an efficient, and for most applications sufficiently accurate and easily reproducible method. The results highlight the usefulness of time‐lapse photography for not only determining the snow covered area, but also for estimating the spatial distribution of snow depth. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

16.
Anthropogenic activities on peatlands, such as drainage, can increase sediment transport and deposition downstream resulting in harmful ecological impacts. The objective of this study was to quantify changes in erosion/deposition quantities and surface roughness in peatland forest ditches by measuring changes in ditch cross‐sections and surface microtopography with two alternative methods: manual pin meter and terrestrial laser scanning (TSL). The methods were applied to a peat ditch and a ditch with a thin peat layer overlaying erosion sensitive mineral soil within a period of two years following ditch cleaning. The results showed that erosion was greater in the ditch with exposed mineral soil than in the peat ditch. The two methods revealed rather similar estimates of erosion and deposition for the ditch with the thin peat layer where cross‐sectional changes were large, whereas the results for smaller scale erosion and deposition at the peat ditch differed. The TLS‐based erosion and deposition quantities depended on the size of the sampling window used in the estimations. Surface roughness was smaller when calculated from the pin meter data than from the TLS data. Both methods indicated that roughness increased in the banks of the ditch with a thin peat layer. TLS data showed increased roughness also in the peat ditch. The increase in surface roughness was attributed to erosion and growth of vegetation. Both methods were suitable for the measurements of surface roughness and microtopography at the ditch cross‐section scale, but the applicability, rigour, and ease of acquisition of TLS data were more evident. The main disadvantage of the TLS instrument (Leica ScanStation 2) compared with pin meter was that even a shallow layer of humic (dark brown) water prevented detection of the ditch bed. The geomorphological potential of the methods was shown to be limited to detection of surface elevation changes >~0.1 m. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

17.
High-resolution quantification of fluvial topography has been enabled by a number of geomatics technologies. Hyperscale surveys with spatial extents of <1 km2 have been widely demonstrated by means of terrestrial laser scanning (TLS) and structure-from-motion (SfM) photogrammetry. Recent advances in the development and integration of global navigation satellite system (GNSS), inertial measurement unit (IMU) and lightweight laser scanning technologies are now resulting in the emergence of personal mobile laser scanners (MLS) that have the potential to increase data acquisition and processing rates by one to two orders of magnitude compared to TLS/SfM, and thus challenge the recent dominance of these technologies. This investigation compares a personal MLS survey using a Leica Pegasus Backpack that integrates Velodyne Puck VLP-16 sensors, and a multi-station static TLS survey using a Riegl VZ-1000 scanner, to produce digital elevation models (DEMs) and surface sedimentology maps. The assessment is undertaken on a 500 m long reach of the braided River Feshie. Comparison to 107 independent real-time kinematic (RTK)-GNSS check points resulted in similar mean error (ME) and standard deviation error (SDE) for TLS (ME = −0.025 m; SDE = 0.038 m) and personal MLS (ME = −0.014 m; SDE = 0.019 m). Direct cloud-to-cloud (C2C) comparison between a sample of TLS and personal MLS observations (2.8 million points) revealed that C2C distances follow a sharply decreasing Burr distribution (a = 2.35, b = 3.19, rate parameter s = 9.53). Empirical relationships between sub-metre topographic variability and median sediment grain size (10–100 mm) demonstrate that surface roughness from personal MLS can be used to map median grain size. Differences between TLS and personal MLS empirical relationships suggest such relationships are dependent on survey technique. Personal MLS offers distinct logistical advantages over SfM photogrammetry and TLS for particular survey situations and is likely to become a widely applied technique. © 2019 John Wiley & Sons, Ltd.  相似文献   

18.
For more than a decade, habitat mapping using biotopes (in‐channel hydraulically‐defined habitats) has underpinned aquatic conservation in the UK through (a) providing baseline information on system complexity and (b) allowing environmental and ecological change to be monitored and evaluated. The traditional method used is the subjective river habitat or corridor survey. This has recently been revised to include the floodplain via GeoRHS, but issues still exist concerning development of a national database due to the labour intensive nature of the data collection, subjectivity issues between samplers, temporal changes, the fuzzy nature of perceived habitats and habitat boundaries. This paper takes an innovative approach to biotope definition using high resolution spatial data to define water surface roughness for two representative reaches of the River South Tyne, Cumbria, and the River Rede, Northumberland, UK. Data was collected using a terrestrial laser scanner (TLS) and hydraulic variability simply expressed through assigning a local standard deviation value to a set of adjacent water surface values. Statistical linkage of these data with biotope locations defined visually in the field allowed complete mapping of the surveyed reach defining habitat and biotope areas to the fine scale resolution of the TLS data. Despite issues of data loss due to absorption and transmission through the water, the reflected signal generated an extremely detailed and objective map of the water surface roughness, which may be compared with known biotope locations as defined by visual identification in the field. The TLS accuracy achieved in the present study is comparable with those obtained using hyperspectral imagery: with 84% of the pool/glide/marginal deadwater amalgamated biotope, 88% of riffles, 57% of runs and 50% of the amalgamated cascade/rapid biotope successfully plotted. It is clear from this exercise that biotope distribution is more complex than previously mapped using subjective techniques, and based upon the water surface roughness delimiters presented in this study, the amalgamation of pools with glides and marginal deadwaters, riffles with unbroken standing waves, and cascades with rapids, is proposed. Copyright © 2010 John Wiley & Sons, Ltd  相似文献   

19.
The boat‐based, mobile mapping system (BoMMS) with a laser scanner allows the derivation of detailed riverine topographical data for fluvial applications. Combined with data acquisition from static terrestrial LiDAR (light detection and range) or mobile terrestrial LiDAR on the ground, boat‐based laser scanning enables a totally new field mapping approach for fluvial studies. The BoMMS approach is an extremely rapid methodology for surveying riverine topography, taking only 85 min to survey a reach approximately 6 km in length. The BoMMS approach also allowed an effective survey angle for deep river banks, which is difficult to achieve with aerial or static terrestrial LiDAR. Further, this paper demonstrates the three‐dimensional mapping of a point‐bar and its detailed morphology. Compared with the BoMMS surface, approximately, 80% and 96% of the terrestrial LiDAR points showed a height deviation of less than 2 cm and 5 cm, respectively, with an overall standard deviation of ± 2·7 cm. This level of accuracy and rapidity of data capture enables the mapping of post‐flood deposition directly after a flood event without an extensive time lag. Additionally, the improved object characterisation may allow for better 3D mapping of the point bar and other riverrine features. However, the shadow effect of the BoMMS survey in point bar mapping should be removed by additional LiDAR data to acquire entire riverine topography. The approach demonstrated allowed a large reach to be surveyed compared with static terrestrial LiDAR and increased the spatial limit of survey towards aerial LiDAR, but it maintains the same or even better temporal resolution as static terrestrial LiDAR. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

20.
LiDAR data were used to quantify and analyse a rockfall event which occurred in 2003 in the Western Dolomites (Italian Alps). In addition to previously existing airborne laserscanning (ALS) data, high resolution terrestrial laserscanning (TLS) data were collected. By using the original point clouds, the volume, axial ratio and runout length of single boulders as well as the surface roughness in the runout zone of the rockfall were derived. The total volume of the rockfall event of approximately 10 000 m³ was estimated by a reconstruction of the pre‐event surface at the detachment zone. The analysis of the laser scanning data of the accumulation zone revealed a power law scaling for boulder volumes larger than 8 m³. The dependence of runout length on boulder volume is complex; it is moderated by particle sphericity. In addition, we used ALS and TLS data to derive the spatial distribution of surface roughness on the talus cone. TLS allow for more accurate roughness mapping than ALS data, but for most applications the point density of ALS data seems to be sufficiently high to derive measures of roughness. Different sampling approaches for plane fitting on the scale of 5 m did not show significant effects besides the computational time. The results of our analyses provide important perspectives for rockfall modelling and process understanding with potential applications in both ‘applied’ (natural hazards) and ‘pure’ geomorphological research. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号