首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 781 毫秒
1.
The fate and transport of contaminants in the vicinity of septic fields remains poorly understood in many hydrogeomorphological environments. We report hydrometric data from an intensive hillslope‐scale experiment conducted between 29 August and 11 November 1998 at a residential leach field in New York State. The objective of our study was to characterize water flux within the vadose zone, understand the physical controls on the flux, and predict how this ultimately will affect subsurface water quality. Soil‐water flux was calculated using matric potential measurements from a network of 25 tensiometer nests, each nest consisting of three tensiometers installed to depths of 10, 50 and 130 cm. Unsaturated hydraulic conductivity curves were derived at each depth from field‐determined time‐domain reflectometry–tensiometry moisture‐release curves and borehole permeametry measurements. Flownets indicated that a strong upward flux of soil water occurred between rainstorms. Following the onset of (typically convective) rainfall, low near‐surface matric potentials were rapidly converted to near‐saturated and saturated conditions, promoting steep vertical gradients through the near‐surface horizons of the hillslope. Lateral hydraulic gradients were typically 10 times smaller than the vertical gradients. Resultant flow vectors showed that the flux was predominantly vertical through the vadose zone, and that the flux response to precipitation was short‐lived. The flux response was controlled primarily by the shape of the unsaturated hydraulic conductivity curves, which indicated a rapid loss of conductivity below saturation. Thus, soil water had a very high residence time in the vadose zone. The absence of rapid wetting at 130 cm and the delayed and small phreatic zone response to rainfall indicated that water movement through macropores did not occur on this hillslope. These results are consistent with a Cl tracing experiment, which demonstrated that the tracer was retained in the vadose zone for several months after injection to the system. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

2.
The impact of three-dimensional subsurface heterogeneity in the saturated hydraulic conductivity on hillslope runoff generated by excess infiltration (so-called Hortonian runoff) is examined. A fully coupled, parallel subsurface–overland flow model is used to simulate runoff from an idealized hillslope. Ensembles of correlated, Gaussian random fields of saturated hydraulic conductivity are used to create uncertainty in spatial structure. A large number of cases are simulated in a parametric manner with the variance of the hydraulic conductivity varied over orders of magnitude. These cases include rainfall rates above, equal and below the geometric mean of the hydraulic conductivity distribution. These cases are also compared to theoretical representations of runoff production based on simple assumptions regarding (1) the rainfall rate and the value of hydraulic conductivity in the surface cell using a spatially-indiscriminant approach; and (2) a percolation-theory type approach to incorporate so-called runon. Simulations to test the ergodicity of hydraulic conductivity on hillslope runoff are also performed. Results show that three-dimensional stochastic representations of the subsurface hydraulic conductivity can create shallow perching, which has an important effect on runoff behavior that is different than previous two-dimensional analyses. The simple theories are shown to be very poor predictors of the fraction of saturated area that might runoff due to excess infiltration. It is also shown that ergodicity is reached only for a large number of integral scales (∼30) and not achieved for cases where the rainfall rate is less than the geometric mean of the saturated hydraulic conductivity.  相似文献   

3.
Small‐scale point velocity probe (PVP)‐derived velocities were compared to conventional large‐scale velocity estimates from Darcy calculations and tracer tests, and the possibility of upscaling PVP data to match the other velocity estimates was evaluated. Hydraulic conductivity was estimated from grain‐size data derived from cores, and single‐well response testing or slug tests of onsite wells. Horizontal hydraulic gradients were calculated using 3‐point estimators from all of the wells within an extensive monitoring network, as well as by representing the water table as a single best fit plane through the entire network. Velocities determined from PVP testing were generally consistent in magnitude with those from depth specific data collected from multilevel monitoring locations in the tracer test, and similar in horizontal flow direction to the average hydraulic gradient. However, scaling up velocity estimates based on PVP measurements for comparison with site‐wide Darcy‐based velocities revealed issues that challenge the use of Darcy calculations as a generally applicable standard for comparison. The Darcy calculations were shown to underestimate the groundwater velocities determined both by the PVPs and large‐scale tracer testing, in a depth‐specific sense and as a site‐wide average. Some of this discrepancy is attributable to the selective placement of the PVPs in the aquifer. Nevertheless, this result has important implications for the design of in situ treatment systems. It is concluded that Darcy estimations of velocity should be supplemented with independent assessments for these kinds of applications.  相似文献   

4.
In response to growing concern about impacts of upland agricultural land management on flood risk, an intensely instrumented experimental catchment has been established at Pontbren, a sheep‐farmed headwater catchment of the River Severn, UK. Primary aims are to develop understanding of the processes governing flood generation and the associated impacts of land management practices, and to bridge the gap between process understanding and ability to predict effects on downstream flooding. To achieve this, the experiment is designed to operate at plot (～100 m2), hillslope (～0·1 km2) and small catchment scale (～10 km2). Hillslope‐scale data, from an under‐drained, agriculturally ‘improved’ pasture, show that drain flow is a dominant runoff process. However, depending on antecedent moisture conditions, overland flow may exceed drain flow rates and can be an important contributor to peak flow runoff at the hillslope‐scale. Flow, soil tension data and tracer tests confirm the importance of macropores and presence of perched water tables under ‘normal’ wet conditions. Comparisons of pasture runoff with that from within a 10 year‐old tree shelterbelt show significantly reduced overland flow due to the presence of trees and/or absence of sheep. Comparisons of soil hydraulic properties show significant increases in hydraulic conductivity and saturated moisture content of soil under trees compared to adjacent improved pasture. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

5.
J. Lewis 《Ground water》2016,54(5):740-744
This technical note describes an effective and inexpensive field technique for measuring the saturated hydraulic conductivity of both undisturbed cores and repacked soil samples. The method requires no specialized equipment; everything that is required can be obtained in a hardware store. The method is a straightforward field implementation of the widely used falling‐head laboratory analysis directly derived from Darcy's law. As such, it sidesteps the need for empirical assumptions about soil texture and the relationship between saturated and unsaturated flow components which many permeameter‐based methods rely upon. The method is shown to produce results that are consistent with K values obtained elsewhere in the same homogeneous sand formation. Furthermore, the proposed method is useful for measuring hydraulic conductivity in drill cuttings obtained from direct push or auguring drill techniques, which cannot be done with any other field method. The range of hydraulic conductivity values that this test is appropriate for is on the order of 1E ? 7 m/s to 1E ? 3 m/s.  相似文献   

6.
Landslides in partially saturated colluvium on Seattle, WA, hillslopes have resulted in property damage and human casualties. We developed statistical models of colluvium and shallow‐groundwater distributions to aid landslide hazard assessments. The models were developed using a geographic information system, digital geologic maps, digital topography, subsurface exploration results, the groundwater flow modeling software VS2DI and regression analyses. Input to the colluvium model includes slope, distance to a hillslope–crest escarpment, and escarpment slope and height. We developed different statistical relations for thickness of colluvium on four landforms. Groundwater model input includes colluvium basal slope and distance from the Fraser aquifer. This distance was used to estimate hydraulic conductivity based on the assumption that addition of finer‐grained material from down‐section would result in lower conductivity. Colluvial groundwater is perched so we estimated its saturated thickness. We used VS2DI to establish relations between saturated thickness and the hydraulic conductivity and basal slope of the colluvium. We developed different statistical relations for three groundwater flow regimes. All model results were validated using observational data that were excluded from calibration. Eighty percent of colluvium thickness predictions were within 25% of observed values and 88% of saturated thickness predictions were within 20% of observed values. The models are based on conditions common to many areas, so our method can provide accurate results for similar regions; relations in our statistical models require calibration for new regions. Our results suggest that Seattle landslides occur in native deposits and colluvium, ultimately in response to surface‐water erosion of hillslope toes. Regional groundwater conditions do not appear to strongly affect the general distribution of Seattle landslides; historical landslides were equally dispersed within and outside of the area potentially affected by regional groundwater conditions. Published in 2007 by John Wiley & Sons, Ltd.  相似文献   

7.
Hydraulic tomography (HT) is a method for resolving the spatial distribution of hydraulic parameters to some extent, but many details important for solute transport usually remain unresolved. We present a methodology to improve solute transport predictions by combining data from HT with the breakthrough curve (BTC) of a single forced‐gradient tracer test. We estimated the three dimensional (3D) hydraulic‐conductivity field in an alluvial aquifer by inverting tomographic pumping tests performed at the Hydrogeological Research Site Lauswiesen close to Tübingen, Germany, using a regularized pilot‐point method. We compared the estimated parameter field to available profiles of hydraulic‐conductivity variations from direct‐push injection logging (DPIL), and validated the hydraulic‐conductivity field with hydraulic‐head measurements of tests not used in the inversion. After validation, spatially uniform parameters for dual‐domain transport were estimated by fitting tracer data collected during a forced‐gradient tracer test. The dual‐domain assumption was used to parameterize effects of the unresolved heterogeneity of the aquifer and deemed necessary to fit the shape of the BTC using reasonable parameter values. The estimated hydraulic‐conductivity field and transport parameters were subsequently used to successfully predict a second independent tracer test. Our work provides an efficient and practical approach to predict solute transport in heterogeneous aquifers without performing elaborate field tracer tests with a tomographic layout.  相似文献   

8.
The strong vertical gradient in soil and subsoil saturated hydraulic conductivity is characteristic feature of the hydrology of catchments. Despite the potential importance of these strong gradients, they have proven difficult to model using robust physically based schemes. This has hampered the testing of hypotheses about the implications of such vertical gradients for subsurface flow paths, residence times and transit time distribution. Here we present a general semi‐analytical solution for the simulation of 2D steady‐state saturated‐unsaturated flow in hillslopes with saturated hydraulic conductivity that declines exponentially with depth. The grid‐free solution satisfies mass balance exactly over the entire saturated and unsaturated zones. The new method provides continuous solutions for head, flow and velocity in both saturated and unsaturated zones without any interpolation process as is common in discrete numerical schemes. This solution efficiently generates flow pathlines and transit time distributions in hillslopes with the assumption of depth‐varying saturated hydraulic conductivity. The model outputs reveal the pronounced effect that changing the strength of the exponential decline in saturated hydraulic conductivity has on the flow pathlines, residence time and transit time distribution. This new steady‐state model may be useful to others for posing hypotheses about how different depth functions for hydraulic conductivity influence catchment hydrological response. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

9.
Infiltration excess overland flow has been identified as the dominant flow pathway in recently reclaimed surface mined watersheds as a result of compaction and sorting during the reclamation procedure. Therefore, there could be a fairly direct relationship between runoff generated from the hillslopes to that measured at the watershed outlet. A 3‐year study was initiated in 1993 to determine how well surface runoff at a watershed scale could be predicted from 1‐m2 runoff frames placed on hillslopes in two reclaimed surface‐mined watersheds in central Alberta. Runoff from the hillslope frames suggests outlet discharge should be high from the 3\4‐ha Sandy Subsoil Watershed and much less for the 9\8‐ha West Watershed, but the opposite occurred. Most of the hillslope runoff from the Sandy Subsoil Watershed infiltrated once it reached the channel and depression storage played an insignificant role in determining runoff. In contrast, most of the runoff from the West Watershed originated from rain falling directly on the saturated channel (depression storage) or near‐channel saturated areas, rather than the hillslopes. Neither watershed runoff magnitude nor timing could be predicted from the same parameters for hillslope runoff frames for either reclaimed watershed. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

10.
Two models for estimating expected areal‐average infiltration rate, ī, at the hillslope scale are presented. The first relies upon the condition of a negligible infiltration of surface water running downslope (run‐on process) into a previous heterogeneous soil. It is an adapted version of an earlier semi‐analytical model. The second incorporates the run‐on process and is based on a lumped approach that uses an effective saturated hydraulic conductivity. This latter was parameterized in terms of the main characteristics of rainfall and soil. Both the models were tested by comparison with the results carried out by Monte‐Carlo simulations over different soil types. It was found that the first model simulated ī with maximum errors in magnitude typically less than 10%. The second model provided similar errors in the total volume of overland flow, and the rising limb of the hydrograph experienced a distortion. Lastly, satisfactory results were obtained by comparing the model without run‐on with an empirical approach particularly accurate for fine‐textured soils. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

11.
A physically based inverse method is developed using hybrid formulation and coordinate transform to simultaneously estimate hydraulic conductivity tensors, steady‐state flow field, and boundary conditions for a confined aquifer under ambient flow or pumping condition. Unlike existing indirect inversion techniques, the physically based method does not require forward simulations to assess model‐data misfits. It imposes continuity of hydraulic head and Darcy fluxes in the model domain while incorporating observations (hydraulic heads, Darcy fluxes, or well rates) at measurement locations. Given sufficient measurements, it yields a well‐posed inverse system of equations that can be solved efficiently with coarse grids and nonlinear optimization. When pumping and injection are active, well rates are used as measurements and flux sampling is not needed. The method is successfully tested on synthetic aquifer problems with regular and irregular geometries, different hydrofacies and flow patterns, and increasing conductivity anisotropy ratios. All problems yield stable inverse solutions under increasing head measurement errors. For a given set of observations, inversion accuracy is strongly affected by the conductivity anisotropy ratio. Conductivity estimation is also affected by flow pattern: within a hydrofacies, when Darcy flux component is very small, the corresponding directional conductivity perpendicular to streamlines becomes less identifiable. Finally, inversion is successful even if the location of aquifer boundaries is unknown. In this case, the inversion domain is defined by the location of the measurements.  相似文献   

12.
Surface soil moisture has been extensively studied for various land uses and landforms. Although many studies have reported potential factors that control surface soil moisture over space or time, the findings have not always been consistent, indicating a need for identification of the main factors. This study focused on the static controls of topographic, soil, and vegetation features on surface soil moisture in a steep natural forested headwater catchment consisting of three hillslope units of a gully area, side slope, and valley‐head slope. Using a simple correlation analysis to investigate the effects of the static factors on surface soil moisture at depths of 0–20 cm at 470 points in 13 surveys, we addressed the characteristics of surface soil moisture and its main controlling factors. The results indicated that the mean of surface soil moisture was in the decreasing order of gully area > valley‐head slope > side slope. The relationship between the mean and standard deviation of surface soil moisture showed a convex‐upward shape in the headwater catchment, a negative curvilinear shape in the gully area, and positive curvilinear shapes at the side and valley‐head slopes. At the headwater catchment and valley‐head slope, positive contributions of soil porosity and negative contributions of slope gradient and saturated hydraulic conductivity were the main controlling factors of surface soil moisture under wetter conditions, whereas positive contributions of topographic wetness index and negative contributions of vegetation density were the main controlling factors of surface soil moisture under drier conditions. At the side slope underlain by fractured bedrocks, only saturated hydraulic conductivity and vegetation density were observed to be the controlling factors. Surface soil moisture in the gully area was mainly affected by runoff rather than were static features. Thus, using hillslope units is effective for approximately estimating the hydrological behaviours of surface moisture on a larger scale, whereas dependency between the main static factors and moisture conditions is helpful for estimating the spatial distributions of surface moisture on a smaller scale.  相似文献   

13.
A borehole permeameter is well suited for testing saturated hydraulic conductivity (K(sat)) at specific depths in the vadose zone. Most applications of the method involve fine-grained soils that allow hand auguring of test holes and require a small water reservoir to maintain a constant head. In non-cohesive gravels, hand-dug test holes are difficult to excavate, holes are prone to collapse, and large volumes of water are necessary to maintain a constant head for the duration of the test. For coarse alluvial gravels, a direct-push steel permeameter was designed to place a slotted pipe at a specific sampling depth. Measurements can be made at successive depths at the same location. A 3790 L (1000 gallons) trailer-mounted water tank maintained a constant head in the permeameter. Head in the portable tank was measured with a pressure transducer and flow was calculated based on a volumetric rating curve. A U.S. Bureau of Reclamation analytical method was utilized to calculate K(sat). Measurements with the permeameter at a field site were similar to those reported from falling-head tests.  相似文献   

14.
Measurements have been made of unsaturated and saturated lateral soil water flow on a convex hill-slope with a good soil cover and impermeable bedrock during natural rainstorms. The hydraulics of flow are examined in detail with particular reference to the role of breaks in vertical permeability, the change from saturated to unsaturated flow and the velocity of flow. In this instance, after rainfall slope flow is dominated by vertical unsaturated movement towards the profile base. Preceding upslope moisture gradients result in the growth of a zone of soil saturation upwards from the slope base. Slope discharge, through the B and B/C horizons, is related to the form of the saturation zone, within which flow is lateral, according to Darcy's law. The time required for vertical percolation and the low hydraulic conductivity of the lower soil horizons result in a hillslope hydrograph which is delayed and attenuated and cannot be regarded as stormflow. During drainage the saturation zone contracts and is replaced by a lateral unsaturated flow system at the profile base which supplies discharge from the B/C horizon for up to 42 days without further recharge. It is concluded that, in general, either distinct soil horizons or impermeable bedrock are essential for the initiation of lateral flow. Saturated flow is likely to dominate hillslope hydrographs through non-capillary pore spaces but these may be integrated to the point where Darcy's law still holds. Although lateral soil water flow must be a widespread phenomenon, it is unlikely to provide storm runoff to the stream unless saturated conditions are generated within the organic horizons for flow within the lower soil horizons is dominated by non-Darcian flow through non-capillary spaces in the soil.  相似文献   

15.
Hillslopes turn precipitation into runoff and thus exert important controls on various Earth system processes. It remains difficult to collect reliable data necessary for understanding and modeling these Earth system processes in real catchments. To overcome this problem, controlled experiments are being conducted at the Landscape Evolution Observatory at Biosphere 2, The University of Arizona. Previous experiments have revealed differences in hydrological response between 2 landscapes within Landscape Evolution Observatory, even though both landscapes were designed to be identical. In an attempt to discover where the observed differences stem from, we use a fully 3‐dimensional hydrological model (CATchment HYdrology) to show the effect of soil water retention characteristics and saturated hydraulic conductivity on the hydrological response of these 2 hillslopes. We also show that soil water retention characteristics can be derived at hillslope scale from experimental observations of soil moisture and matric potential. It is found that differences in soil packing between the 2 landscapes may be responsible for the observed differences in hydrological response. This modeling study also suggests that soil water retention characteristics and saturated hydraulic conductivity have a profound effect on rainfall–runoff processes at hillslope scale and that parametrization of a single hillslope may be a promising step in modeling rainfall–runoff response in real catchments.  相似文献   

16.
Analyses of independent laboratory- and field-scale measurements from two sites on Sapelo Island, Georgia reveal heterogeneity in hydraulic parameters across the upland–estuary interface. Regardless of the method used (short-duration pumping tests, amplitude attenuation of tidal pumping data, sediment grain size distributions, and falling head permeameter tests), we obtain hydraulic conductivity of 10−4 m s−1 for the fine-grained, well-sorted, clean sands that make up the upland areas. Proximal to the upland–estuary boundary, the tidal pumping analyses and permeameter tests suggest that hydraulic conductivities decrease by more than two orders of magnitude, a result consistent with the presence of a clogging layer. Such a clogging layer may arise due to a variety of physical, chemical, or biological processes. The extent and orientation of the layers of reduced hydraulic conductivity near the upland–estuary boundary influence the nature of the aquifer's response to tidal forcing. Where the lower conductivity layer forms a relatively flat creek bank, tidal pumping produces a primarily mechanical response in the adjacent aquifer. Where the creek bank is nearly vertical, there is a more direct hydraulic connection between the tidal creek and the adjacent aquifer. The clogging layer likely contributes to the development of complicated flow pathways across the upland–estuary boundary. Effective flow paths calculated from tidal pumping data terminate within the marsh, beyond the boundary of the upland aquifer, suggesting a diffuse regime of groundwater discharge in the marsh. We postulate that, in many settings, submarsh flow may be as important as seepage faces for groundwater discharge into the marsh–estuary complex.  相似文献   

17.
There are very few experimental studies identifying hydrological pathways within rain forest slopes. Such knowledge is, however, necessary to understand why forest disturbance affects rainfall–riverflow response and nutrient migration. This study examines flow pathways within lowland rain forest slopes comprising Udults of the Ultisol soil order. Experimentation was conducted on four SE Asian hillslope units (each 5 × 5 m in plan) in the Bukit Timah catchment (Singapore Island), and in the W8S5 catchment (Sabah, Borneo Island). The flow pathways were identified by artificial tracer experiments. We evaluated how well hydrometric calculations based on tensiometry and permeametry measurements predicted the tracer patterns. The tracer work indicated much faster subsurface flows at Bukit Timah than W8S5 for the storms studied. Some explanation of the greater subsurface waterflows at Bukit Timah in comparison to W8S5 is afforded by the less steep moisture release curves which maintain hydraulic conductivity as the soil dries. Vertical flow of the tracer through the upper 1 m of soil predominated (>90 per cent of percolation) in the Bukit Timah slopes. In some contrast, a major component (approximately 60 per cent) of the tracer percolation was directed laterally within the W8S5 slopes. The flow vectors calculated using the hydrometric methods did, however, grossly under‐estimate the degree of lateral deflection of waterflow generated at W8S5 and to a lesser extent over‐estimated it at Bukit Timah. In part, these errors may relate to the inability of traditional hydrometric techniques to fully characterize the effect of the large and small ‘natural soil pipes’ present within both catchments. In conclusion, the study indicates that marked variations in flow vectors exist within the Udult great group of SE Asian soils and hydrometric calculations may be poor predictors of these dominant pathways. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

18.
Simulation of soil moisture content requires effective soil hydraulic parameters that are valid at the modelling scale. This study investigates how these parameters can be estimated by inverse modelling using soil moisture measurements at 25 locations at three different depths (at the surface, at 30 and 60 cm depth) on an 80 by 20 m hillslope. The study presents two global sensitivity analyses to investigate the sensitivity in simulated soil moisture content of the different hydraulic parameters used in a one‐dimensional unsaturated zone model based on Richards' equation. For estimation of the effective parameters the shuffled complex evolution algorithm is applied. These estimated parameters are compared to their measured laboratory and in situ equivalents. Soil hydraulic functions were estimated in the laboratory on 100 cm3 undisturbed soil cores collected at 115 locations situated in two horizons in three profile pits along the hillslope. Furthermore, in situ field saturated hydraulic conductivity was estimated at 120 locations using single‐ring pressure infiltrometer measurements. The sensitivity analysis of 13 soil physical parameters (saturated hydraulic conductivity (Ks), saturated moisture content (θs), residual moisture content (θr), inverse of the air‐entry value (α), van Genuchten shape parameter (n), Averjanov shape parameter (N) for both horizons, and depth (d) from surface to B horizon) in a two‐layer single column model showed that the parameter N is the least sensitive parameter. Ks of both horizons, θs of the A horizon and d were found to be the most sensitive parameters. Distributions over all locations of the effective parameters and the distributions of the estimated soil physical parameters from the undisturbed soil samples and the single‐ring pressure infiltrometer estimates were found significantly different at a 5% level for all parameters except for α of the A horizon and Ks and θs of the B horizon. Different reasons are discussed to explain these large differences. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

19.
The TOPMODEL framework was used to derive expressions that account for saturated and unsaturated flow through shallow soil on a hillslope. The resulting equations were the basis for a shallow‐soil TOPMODEL (STOPMODEL). The common TOPMODEL theory implicitly assumes a water table below the entire watershed and this does not conceptually apply to systems hydrologically controlled by shallow interflow of perched groundwater. STOPMODEL provides an approach for extending TOPMODEL's conceptualization to apply to shallow, interflow‐driven watersheds by using soil moisture deficit instead of water table depth as the state variable. Deriving STOPMODEL by using a hydraulic conductivity function that changes exponentially with soil moisture content results in equations that look very similar to those commonly associated with TOPMODEL. This alternative way of conceptualizing TOPMODEL makes the modelling approach available to researchers, planners, and engineers who work in areas where TOPMODEL was previously believed to be unsuited, such as the New York City Watershed in the Catskills region of New York State. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

20.
Hillslope hydrological modelling is considered to be of great importance for the understanding and quantification of hydrological processes in hilly or mountainous landscapes. In recent years a few comprehensive hydrological models have been developed at the hillslope scale which have resulted in an advanced representation of hillslope hydrological processes (including their interactions), and in some operational applications, such as in runoff and erosion studies at the field scale or lateral flow simulation in environmental and geotechnical engineering. An overview of the objectives of hillslope hydrological modelling is given, followed by a brief introduction of an exemplary comprehensive hillslope model, which stimulates a series of hydrological processes such as interception, evapotranspiration, infiltration into the soil matrix and into macropores, lateral and vertical subsurface soil water flow both in the matrix and preferential flow paths, surface runoff and channel discharge. Several examples of this model are presented and discussed in order to determine the model's capabilities and limitations. Finally, conclusions about the limitations of detailed hillslope modelling are drawn and an outlook on the future prospects of hydrological models on the hillslope scale is given.The model presented performed reasonable calculations of Hortonian surface runoff and subsequent erosion processes, given detailed information of initial soil water content and soil hydraulic conditions. The vertical and lateral soil moisture dynamics were also represented quite well. However, the given examples of model applications show that quite detailed climatic and soil data are required to obtain satisfactory results. The limitations of detailed hillslope hydrological modelling arise from different points: difficulties in the representations of certain processes (e.g. surface crusting, unsaturated–saturated soil moisture flow, macropore flow), problems of small‐scale variability, a general scarcity of detailed soil data, incomplete process parametrization and problems with the interdependent linkage of several hillslopes and channel–hillslope interactions. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号