共查询到20条相似文献，搜索用时 280 毫秒
1.
An analytical solution for one-dimensional contaminant diffusion through multi-layered media is derived regarding the change
of the concentration of contaminants at the top boundary with time. The model accounts for the arbitrary initial conditions
and the conditions of zero concentration and zero mass flux on the bottom boundary. The average degree of diffusion of the
layered system is introduced on the basis of the solution. The results obtained by the presented analytical solutions agree
well with those obtained by the numerical methods presented in the literature papers. The application of the analytical solution
to the problem of landfill liner design is illustrated by considering a composite liner consisting of geomembrane and compacted
clay liner. The results show that the 100-year mass flux of benzene at the bottom of the composite liner is 45 times higher
than that of acetone for the same composite liner. The half-life of the contaminant has a great influence on the solute flux
of benzene diffused into the underlying aquifer. Results also indicates that an additional 2.9–5.0 m of the conventional (untreated)
compacted clay liner under the geomembrane is required to achieve the same level of protection as provided by 0.60 m of the
Hexadecyltrimethylammonium (HDTMA)-treated compacted clay liners in conjunction with the geomembrane. Applications of the
solution are also presented in the context of a contaminated two-layered media to demonstrate that different boundary and
initial conditions can greatly affect the decontamination rate of the problem. The method is relatively simple to apply and
can be used for performing equivalency analysis of landfill liners, preliminary design of groundwater remediation system,
evaluating experimental results, and verifying more complex numerical models. 相似文献
2.
Abbas El‐Zein 《国际地质力学数值与分析法杂志》2008,32(3):265-287
Finite‐element models of contaminant transport through composite landfill liners require highly refined meshes around the interface between the geomembrane and the clay layer, especially if leakage through holes in the geomembrane is considered. In addition, no general formulation for transport through leaking geomembranes can be found in the literature. The paper develops a general approach to time‐dependent contaminant migration through composite liners with intact or leaking geomembranes. Equations are derived for various combinations of system conditions including Dirichlet and Neumann boundary conditions in the waste, constant mass of contaminants in the waste, steady state or transient transport in the geomembrane, and steady state or transient seepage velocities in the mineral liner. The effect of the geomembrane on transport in the soil is converted into an equivalent boundary condition applicable at the top of the clay layer. Hence, only the media underlying the top geomembrane are explicitly represented in the numerical model, yielding a computationally efficient algorithm. The new formulation is validated in conjunction with finite‐layer, finite‐element and boundary‐element methods, by comparing its predictions to those of more conventional approaches which represent the geomembrane explicitly. The scope of the method is illustrated by modelling a landfill liner with a geomembrane leaking in five locations. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
3.
土工膜和下伏压实黏土组成的复合衬层已被广泛用作填埋场的防渗屏障系统。有机污染物在复合衬层中迁移时,其主要运移机制是扩散作用。假设有机污染物在土工膜中稳态扩散,并假设在下伏衬层中扩散系数为迁移距离的线性函数,且考虑降解作用的影响,建立了有机污染物在复合衬层中的一维扩散模型,针对零浓度下边界条件,获得了模型解析解。基于该解析解,分析讨论了相关参数的敏感性。结果表明,相关参数对计算结果影响很大,降解半衰期对污染物运移同样存在较大影响。该解析模型仅适用于有机污染物在两层复合衬垫中的迁移问题,可为填埋场的初步设计提供参考 相似文献
4.
In this paper, an extensive parametric sensitivity analysis of coupled consolidation and solute transport in composite landfill liner systems has been undertaken. The analysis incorporates results of more than 3000 simulations for various combinations of barrier thickness, waste loading rate, initial void ratio, compression index, hydraulic conductivity and dispersion coefficient. However, it is noted that to limit the extent of the study a constant coefficient of consolidation is assumed in the analysis presented here, though this assumption is easily relaxed. Results of the parametric sensitivity analysis are succinctly presented using dimensionless plots, which allow the comparison of results for a large number of parameter values, and so the clear identification of the most important determinants on contaminant transport through the liner system. The dimensionless plots demonstrate a pessimum (for which the ‘breakthrough time’ is minimised). Numerical results reveal that in cases of extreme liner compressibility an order of magnitude reduction in contaminant transit time may arise due to coupling between solute transport and consolidation, while for barriers of low compressibility and porosity (such as well-engineered composite compacted clay landfill liners), it is found that the contaminant transit time may still be reduced by more than 30%. The numerical results suggest that the use of coupled consolidation–contaminant transport models are sometimes required for informed and conservative landfill liner design. 相似文献
5.
Performance-based design of landfill liners 总被引：6，自引：0，他引：6
Factors affecting chemical transport in geomembrane, clay and composite liners are reviewed, and a simplified performance-based method for evaluating landfill bottom liners is presented. For single geomembrane liners, mass transport of inorganic chemicals is calculated from the leakage rate from holes for an assumed frequency of hole occurrence. Transport of organic chemicals is obtained by accounting for molecular diffusion through the intact geomembrane. Migration of inorganic and organic chemicals in compacted clay liners is calculated using a solution of the 1D advection–dispersion-reaction equation. For composite liners consisting of a geomembrane and a clay liner, 3D flow and transport of inorganic chemicals is approximated using an equivalent 1D model for transport through an effective area of transport. The approximation is based on results from 3D analyses that have been conducted for a variety of cases. Migration of organic chemicals through composite liners is calculated using a 1D diffusion model. Applicability of the method is illustrated by using it to evaluate the relative performance of several different liner systems. 相似文献
6.
CCL吸附特性及孔隙率降低对污染物运移的影响 总被引：1，自引：0，他引：1
假定孔隙均匀地分布于土体的物质空间内和土骨架对污染物的吸附特性服从平衡线性,对基本体积质量关系进行分析,提出了由于土体对污染物的吸附而引起的孔隙率降低的估算公式。在考虑土体孔隙率变化的条件下,建立了污染物一维运移的控制方程,并考虑垃圾生物降解效应、压实黏土衬里（CCL）防渗层、下覆有限厚度含水层等实际情况,确定了初始条件和边界条件。对所建立的初边值问题进行了数值求解,且对某假想填埋场情况进行了变动参数与对比计算,结果表明,由于土颗粒对污染物的吸附所引起的孔隙率降低,显著地降低了污染物对压实黏土衬里的穿透能力。与常孔隙率情况相比,CCL中污染物的峰值浓度降低近10 %,含水层中污染物浓度降低更显著。当考虑土体孔隙率变化时,弥散对污染物运移具有控制作用,分布系数对污染物的运移具有重要影响。 相似文献
7.
Clay liners or compacted earthen barriers are important barrier materials used for preventing contaminant transport through soils. A low hydraulic conductivity (k) is a significant parameter that governs the design and construction of clay liners. Compacted expansive clays, which are montmorillonite clays, also have a very low hydraulic conductivity (k). When expansive clays are blended with fly ash, an industrial waste, the hydraulic conductivity (k) further reduces as the ash-clay blends result in increased dry densities at increased fly ash contents. Hence, fly ash-stabilised expansive clay can also be proposed as a unique clay liner material. As expansive clays undergo heave when they come into contact with water, it is necessary to study the heave behaviour of fly ash-stabilised expansive clay liners. This paper presents heave studies on fly ash-stabilised expansive clay liners. Fly ash in different contents by dry weight of the expansive clay was added to the clay, and the ash-clay blend was compacted as a liner overlying a natural field soil layer. Compacted lateritic clay was used for simulating the natural field soil into which contaminants migrate. Calcium chloride (CaCl2) solution of varying concentration (5, 10, 20, 50, 100 and 500 mM) was used as the permeating fluid in the heave studies. The rate of heave and the amount of heave of the fly ash-stabilised expansive clay liners were monitored. Deionised water (DIW) was also used as inundating fluid for comparative study. Heave (mm) decreased with increase in solute concentration for all fly ash contents. For a given solute concentration, heave decreased up to a fly ash content of 20 % and thereafter it increased when the fly ash content was increased to 30 %. Heave of the fly ash-stabilised expansive clay liners was correlated with their permeability, liquid limit (LL) and free swell index (FSI) pertaining to the respective fly ash content and CaCl2 concentration. 相似文献
8.
土工合成材料粘土衬垫(GCL)与土工膜(GM)形成的复合衬垫在垃圾填埋场中的应用日益广泛。我国规范中允许在特殊情况下用GCL代替压实粘土(CCL)做垃圾填埋场的衬垫,但是对于“特殊情况”没有明确说明。本文采用数值方法对复合衬垫中无机污染物的对流和扩散进行了计算,从衬垫底部污染物通量和累积量两个角度对GCL复合衬垫和CCL复合衬垫阻滞污染物运移的效果进行了比较,分析两种复合衬垫的等效性,并研究了GCL复合衬垫的适用范围。结果表明,当渗滤液水头较高时,GCL复合衬垫体现出其优势。 相似文献
9.
The migration of contaminants through a 2.9 m thick compacted clay liner (CCL) for a landfill leachate lagoon is examined 14 years after construction. The clay liner formed the lower portion of the composite liner system but the geomembrane (GM) was found to have defects that had allowed leachate to migrate between the GM and CCL. Chloride, sodium, potassium, calcium and magnesium pore water profiles through the CCL are examined. It is shown that chloride migrated approximately 1.7 m into the CCL during the 14 years of the lagoon operation, sodium approximately 1.2 m, and potassium 0.7 m. Diffusion and sorption data from laboratory diffusion testing are utilized in combination with a finite layer contaminant transport model to predict field contaminant migration profiles through the composite liner system and to establish the time of ‘failure’ of the geomembrane at sometime between 0 and 6 years after installation. Relatively high sorptive uptake of potassium by the CCL soil is observed from batch testing and diffusion testing with field data suggesting an even larger amount of sorption. It is hypothesized that organic sludge matter at the base of the lagoon is responsible for potassium uptake from the leachate. This field case highlights the importance of the compacted clay liner as part of the composite liner system in acting as a diffusion barrier during the lifetime of the lagoon as well as using relatively non-conservative contaminants such as chloride and sodium to estimate geomembrane ‘failure’ times 相似文献
10.
有机污染物在完好复合衬垫中的迁移分析 总被引：1，自引：0，他引：1
在复合衬垫中,有机污染物除了在土工膜缺陷处发生迁移外,在完好土工膜中的迁移也是主要方式。考虑有机污染物在土工膜边界处的浓度跳跃现象,建立了有机污染物在完好复合衬垫中迁移的一维模型,得到了解析解。通过与有限差分解的比较,验证了解答的合理性。应用该解答分析了GCL复合衬垫和CCL复合衬垫防止有机污染物渗漏的效果。结果表明,CCL复合衬垫的效果较好,可以通过黏土改性和增加黏土厚度的方法来提高其有效性。有机污染物类型的选择对GCL复合衬垫的分析结果影响较大,而阻滞系数的变化对分析结果影响较小。 相似文献
11.
Flux equations for liquid and solute migration through clay barriers that behave as semi-permeable membranes used in waste containment and remediation applications, known as clay membrane barriers (CMBs), are discussed. The results of a simplified analysis of flow through a geosynthetic clay liner (GCL) using measured values for the chemico-osmotic efficiency coefficient (ω) of the GCL indicate a total liquid flux that counters the outward Darcy (hydraulic) flux due to chemico-osmosis associated with clay membrane behavior of the GCL. Also, the solute (contaminant) flux through the GCL is reduced relative to the solute flux that would occur in the absence of membrane behavior due to chemico-osmotic counter advection and solute restriction. Since diffusion commonly controls solute transport through GCLs and other low-permeability clay barriers, the implicit (empirical) correlation between ω and the effective salt-diffusion coefficient of the migrating contaminant is an important consideration with respect to contaminant restriction in CMBs. 相似文献
12.
Consolidation of clayey contaminant barriers such as landfill liners has been postulated as a cause of early breakthrough of contaminants. In this paper we theoretically investigate this proposition. For this purpose a sophisticated one‐dimensional, large‐deformation model of coupled mechanical consolidation and solute transport is employed. This new model is a generalization of existing coupled consolidation and solute transport models described in the literature. It takes into account both non‐linearities in geometry as well as constitutive relations. The latter relate the compressibility, hydraulic conductivity and coefficient of effective diffusivity to the deformation of the soil. The model is applied to a case study of a clay liner and geomembrane system. Results obtained from numerical solution of the model equations are compared with those from various simplified models, including a ‘diffusion only’ (i.e. a rigid soil) model traditionally used in contaminant barrier design. For barriers incorporating low compressibility soils (as for many well compacted clays), there is little difference between contaminant transit (i.e. breakthrough) times predicted by the two models. However, for contaminant barriers incorporating more compressible soils, consolidation is shown to significantly accelerate transport. These results indicate the potential importance of accounting for the effects of soil consolidation and highlight the limitations of existing models when modelling solute transport through composite barriers utilizing soft soils. Based on these limited results, we suggest a possible way of taking into account soil consolidation using simplified models. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
13.
14.
有机污染物在复合衬垫中的运移以扩散方式为主。目前关于运移参数不确定性及其对衬垫性能影响的研究还不多,复合衬垫厚度的设计也没有考虑不确定性的影响。总结了运移参数已有的成果,采用蒙特卡罗法研究了半无限条件下运移参数的变异性对衬垫底部污染物质量浓度和通量的影响,并对衬垫厚度进行了设计。研究表明:土工膜中有机污染物的分配系数和扩散系数的变异性对质量浓度和通量的影响可以忽略,而土中有机污染物的扩散系数和阻滞系数的变异性对其影响则非常显著。确定性方法计算的结果偏于危险,有必要加强对土中有机污染物的扩散系数和阻滞系数概率特性的研究。以甲苯为例进行黏土衬垫厚度设计,结果表明:概率计算方法得到的黏土衬垫厚度约为确定性方法的1.71~1.81倍,采用概率方法进行衬垫设计更合理。 相似文献
15.
非平衡-非线性吸附情况下填埋场污染物运移分析 总被引：10，自引：0，他引：10
采用Langmuir等温吸附线方程描述非线性吸附性能, 基于改进的混合元方法，通过数值计算与分析，探讨了非平衡吸附条件下污染物运移过程及其机理。计算结果表明: 当考虑非平衡、非线性吸附性能时, 污染物穿透曲线即浓度的时程变化曲线尖锐而狭窄、峰值点前移, “拖长尾”现象不明显, 由此说明，土颗粒对污染物的非平衡、非线性吸附使得污染物的穿透能力增强, 滞留能力下降。进一步的变动参数比较分析表明：Langmuir等温线方程中的参数B、压实粘土衬里的渗透性及地下水渗流速度对污染物运移过程具有显著的影响。 相似文献
16.
Earthen barriers or clay liners are a major concern in geo-environmental engineering. They are designed to preclude or reduce leachate migration. Hence, a low hydraulic conductivity (k) is an important parameter in the design of clay liners. Materials such as bentonite and lateritic clays, which have a low hydraulic conductivity at high dry densities, are used in the construction of clay liners. Compacted expansive clays which are high in montmorillonite content also have a very low hydraulic conductivity. When expansive clays are blended with fly ash, an industrial waste, the hydraulic conductivity further reduces as the ash-clay blends result in increased dry densities at increased fly ash contents. Hence, fly ash-stabilised expansive clay can also be proposed as an innovative clay liner material. It is, therefore, required to study various physical and engineering properties of this new clay liner material. Liquid limit (LL) and free swell index (FSI) are important index properties to be studied in the case of this clay liner material. The hydraulic conductivity of this new clay liner material depends on the fly ash content in the blend. Further, parameters such as solute concentration and kinematic viscosity also influence hydraulic conductivity of clay liners. This paper presents experimental results obtained on hydraulic conductivity (k) of fly ash-stabilised expansive clay liner at varying fly ash content and solute concentration. The tests were performed with deionised water (DIW), CaCl2, NaCl and KCl as permeating fluids. Fly ash content in the blend was varied as 0, 10, 20 and 30 % by weight of the expansive clay, and the solute concentration was varied as 5 mM (milli molar), 10, 20, 50, 100 and 500. It was found that hydraulic conductivity (k) decreased with increasing fly ash content, solute concentration and kinematic viscosity. Further, hydraulic conductivity (k) was correlated with LL and FSI of the clay liner material for different fly ash contents and solute concentrations. Useful correlations were obtained. 相似文献
17.
利用广义积分变换法推导了非等温条件下污染物在压实黏土衬垫中的运移解析解。所提出的解析解考虑了分子扩散、对流、吸附和热扩散的耦合效应,并考虑了压实黏土的渗透系数、分布系数和有效扩散系数3个参数随温度的变化。通过与热扩散试验结果、已有的解析解和基于COMSOL软件的数值模型的对比,验证了所提出的解析解。利用经过验证的解析解,研究了非等温环境以及压实黏土的渗透系数、有效扩散系数和分布系数3个参数随温度的变化对甲苯在压实黏土衬垫系统中迁移的影响。结果表明,非等温环境以及压实黏土的渗透系数、有效扩散系数和分布系数随温度的变化均对甲苯在压实黏土衬垫中迁移有着显著的影响。不考虑非等温环境的影响将极大低估污染物的溢出量和污染物的击穿时间。既有解析解忽略压实黏土的渗透系数和有效扩散系数随温度的变化会极大低估甲苯的流出速率,而忽略压实黏土分布系数随温度的变化会极大高估甲苯击穿衬垫系统的时间和达到稳态的时间。所提出的解析解能够考虑热扩散作用,同时考虑了压实黏土的渗透系数、分布系数和有效扩散系数3个参数随温度的变化,较既有解析解更贴近工程实际,能够为压实黏土衬垫系统的设计和服役性能评价提供指导和借鉴。 相似文献
18.
For materials of very low hydraulic conductivity used in the landfill liner systems, e.g., natural clay liners, soil-cement liners, etc., diffusion characteristics should be evaluated, as the transport mechanism of contaminant through them is diffusion controlled. Studies on the diffusion characteristics of the hardened liner materials, such as the soil cement, are relatively few compared with those of clayey soils. In this paper, diffusive characteristics of hardened liner materials (HLMs) applied to the liner system of Sudokwon Metropolitan Landfill in Korea, were studied. Laboratory pure diffusion column tests in the pure- and the advection-diffusion status were performed for the chemicals, NaCl, KCl, and CaCl2. To evaluate the diffusion coefficient of a HLMs system, a one-dimensional numerical transport program was developed for use in a multi-layered HLMs system. The range of dispersion coefficients of advection diffusion column tests was a little narrower than that of diffusion coefficients of pure diffusion tests, although the two coefficients were quite close. The effective diffusion coefficients of chloride ions of a HLMs were about a half of those in clayey soil due to the high density by compaction and curing. Diffusion coefficients of chloride ions in this study were correlated closely with hydraulic conductivities of the materials tested and were consistent with work in the literature. 相似文献
19.
Diffusion and sorption experiments using a DKS permeameter 总被引：2，自引：0，他引：2
The analysis of contaminant transport through clay liner is a relevant aspect in the design of industrial, urban and mining waste disposal systems, since these areas must be designed and operated to prevent contaminating substances from reaching underground water systems in unacceptable concentrations. The design requires an estimate of the potential contaminant transport rate. However, before any attempt at quantification can be made, values for transport mechanism control parameters must be established. Clayey materials are frequently used as contaminant barriers. In these materials, which have low hydraulic conductivity, the main contaminant transport mechanism is molecular diffusion. Parameters controlling transport for these conditions are the diffusion coefficient and sorption parameters. These parameters depend on soil constituents and characteristics as well as on the chemical constitution of the contaminant. The great complexity of the factors involved makes it necessary to determine the parameters of each type of soil. This paper discusses an equipment called DKS permeameter (diffusion, convection, sorption), for the study of soil-contaminant transport mechanisms, designed at the Institute for Soil Mechanics of the Ruhr-University Bochum, and some results obtained from its use at COPPE/Federal University of Rio de Janeiro (UFRJ), Brazil. This equipment determines the effective diffusion coefficient and sorption parameter with a better reflection of field conditions. The soil under study is a mix of sodium–bentonite that has low hydraulic conductivity (k=10−9 cm/s) with adequate liner characteristics. The result indicated the relevance of determining sorption parameters for structured soils, since the sorption perceived from batch test results using pulverised soil represents maximum soil capacity. Designs based on this parameter would overestimate the attenuation capacity of the liner. 相似文献
20.
分析了运移参数的变化对GCL中污染物运移的影响。从衬垫底部浓度比、对流和扩散通量、污染物累积运移量等方面,对污染物在GCL中的运移进行了计算。结果表明,减小渗透系数和扩散系数可以有效减缓衬垫底部浓度比的增加速度。渗透系数对对流通量的大小、扩散通量的变化速度的影响较大;扩散系数主要影响最大扩散通量。当渗透系数较大时,可以忽略扩散累积运移量,用对流累积运移量代替总累积运移量引起的误差很小。当渗透系数较小时,忽略扩散运移量可能产生较大的误差,尤其是在扩散系数也较大的情况下误差更加明显。 相似文献