共查询到18条相似文献，搜索用时 142 毫秒
1.
2.
由于在前壁上设置了尺寸较小的孔,开孔沉箱受流体黏性力作用显著,依照弗劳德数相似准则设计模型存在比尺效应。为揭示比尺效应,建立了模拟波浪与开孔沉箱相互作用的光滑粒子流体动力学(SPH)模型。其中流体运动由连续性方程和Navier-Stokes方程控制,固壁边界由改进的动力边界粒子施加。模型收敛性通过分析不同粒子分辨率下的波浪反射系数得到,模型精度通过比较计算与理论波浪反射系数证明。使用经过验证的SPH模型,计算并比较了不同几何比尺和开孔率下开孔沉箱附近的涡量场、箱体外侧的波面时程曲线和波浪反射系数。结果表明,随着模型几何比尺的减小,开孔沉箱受到偏大的流体黏性力,致使更多波能在湍流运动中耗散,进而减小了波浪反射系数并降低了箱体外侧的波面高度。 相似文献
3.
基于线性势流假定,对斜向波作用下带横隔板局部开孔沉箱防波堤的水平波浪力进行了理论研究。给出了开孔沉箱法向水平力和横隔板受力的理论计算方法,在极限情况下波浪力的计算结果与文献中的已有结果一致。利用数值算例分析了开孔沉箱总水平力的主要影响因素。开孔沉箱法向总水平力的减小主要集中于结构上半部分波浪影响范围以内。增加单个开孔沉箱的长度有利于减小结构所受总水平波浪力。当波浪入射角或沉箱前开孔墙孔隙影响系数幅值较大时,开孔沉箱横隔板上总水平力的最大值要超过相应的沉箱法向总水平力,此时要注意横隔板的强度问题。 相似文献
4.
沉箱预制时在沉箱底部四个角各放置一个木盒,该木盒经防腐处理,一面作为牵引孔、朝外、不封、其余五面用木板封住。木盒上面预留一个直径15㎝朝上的销钉孔,放置销钉。放置木盒时需与周边钢筋留有至少8㎝以上的钢筋混凝土保护层,浇筑混凝土时在销钉孔放置圆形预埋件。沉箱出运时以钢丝绳扣为拉鼻,通过销钉孔利用大直径圆钢作为销钉固定钢丝绳,牵引机将拖运牵引力传给沉箱,带动沉箱前移。 相似文献
5.
双消浪室局部开孔沉箱防波堤具有低反射、结构受力小、适宜较大水深和工程造价低等优点。为明确双消浪室局部开孔沉箱水动力特性的主要影响因素,采用理论分析和物理模型试验相结合的方法,对规则波和不规则波作用下双消浪室局部开孔沉箱防波堤的反射特性进行研究。基于势流理论,建立规则波和不规则波对局部开孔沉箱防波堤作用的三维解析解,采用二次压力损失边界条件考虑沉箱开孔墙对波浪运动的影响,利用周期性边界条件考虑防波堤结构沿长度方向的周期性变化。开展相应规则波和不规则波物理模型试验,验证理论模型的合理性。通过算例分析,研究不同波浪要素和结构参数对防波堤反射特性的影响。研究表明:双消浪室局部开孔沉箱相对消浪室宽度取值为0.08~0.20,沉箱前墙开孔率大于后墙开孔率时,防波堤在较大波浪频率范围内消波效果显著;当前后墙的开孔率相等时,防波堤反射系数的最小值随着开孔率增大而减小。 相似文献
6.
采用气嚢搬运沉箱上浮船坞和浮船坞坐底出运沉箱的施工工艺,施工效率高且安全可靠,该工艺已在沉箱施工中得到了广泛应用。结合浮船坞修理改造后首次应用于渤海重工30万吨级大型船坞工程实例,介绍了浮船坞出运沉箱技术的工艺流程和施工要点,对类似工程的施工具有一定的参考价值。 相似文献
7.
本文基于雷诺平均的Navier-Stokes方程和k-ε模型求解湍流流动,采用流体体积法(Volume of Fluid,VOF)追踪自由表面运动,建立无反射波浪数值水槽,对多消浪室开孔沉箱的消浪特性进行数值模拟研究。将单消浪室和多消浪室开孔沉箱反射系数和结构前波面分布的数值分析结果与物理模型试验结果进行对比验证,两者符合良好。利用数值算例,研究多消浪室开孔沉箱的反射特性以及开孔结构附近的速度场和湍流强度分布。分析结果表明:波浪与开孔沉箱相互作用时,涡旋和湍动主要分布在开孔墙和消浪室内部自由表面附近;与单消浪室开孔沉箱相比,多消浪室开孔沉箱可以更有效的耗散波浪能量,降低结构的反射系数。本文分析结果可为开孔沉箱结构的工程设计提供参考依据。 相似文献
8.
多消浪室局部开孔沉箱防波堤反射特性的迭代解析研究 总被引：1，自引：0，他引：1
基于势流理论,对多消浪室局部开孔沉箱防波堤的反射特性进行解析研究。研究中采用开孔墙处的二次压力损失边界条件,可以直接考虑波高对于开孔墙处能量损失的影响。利用匹配特征函数展开法和迭代方法得到当前问题的解析解。收敛性验证表明,迭代计算和级数解均具有良好的收敛性。该解析解的计算结果与分区边界元的数值计算结果一致,并且与已有的试验结果符合良好。通过算例分析,研究开孔沉箱防波堤反射系数的主要影响因素。结果表明：与单消浪室开孔沉箱防波堤相比,多消浪室开孔沉箱防波堤可以在更宽的波浪频率范围内保持低反射;增大开孔墙的开孔率,有利于降低多消浪室开孔沉箱防波堤的反射系数;当开孔墙的开孔率沿着入射波方向依次递减时,多消浪室开孔沉箱防波堤的反射系数较小。本文所建立的解析模型简单可靠,可用于工程初步设计中分析开孔沉箱防波堤的水动力性能。 相似文献
9.
10.
开孔率是开孔沉箱波浪反射系数的重要影响因素,迄今为止关于开孔沉箱的物模试验研究成果(包括《防波堤设计与施工规范》)中,开孔率μ通常以线性关系反映在开孔沉箱波浪反射系数的计算关系式中,适用范围为0.2~0.4。但当μ0.2或μ0.4时,开孔率μ对波浪反射系数Kr的影响规律尚需进一步的研究探讨。现借助二维数值波浪水槽,在扩大了的开孔率取值范围内,模拟不规则波与可渗明基床上开孔沉箱的相互作用。结果表明:在0.2≤μ≤0.4的范围内,用线性关系描述开孔率μ对波浪反射系数Kr的影响是合适的;在μ0.4时,数模值和物模试验拟合的经验关系式的趋势是一致的;在μ0.2时,开孔沉箱反射系数K_r随开孔率μ的减小而增大,用物模试验拟合的经验关系式及《防波堤设计与施工规范》中计算公式的线性关系来描述开孔率μ对反射系数K_r的影响是不恰当的。研究成果对开孔沉箱消浪机理的深入认识和开孔沉箱结构的优化设计具有重要意义。 相似文献
11.
A series of model tests were performed on steel- and Perspex-made suction caissons in saturated dense marine sand to explore installation and extraction behaviors. The extractions of the caisson were conducted by applying monotonic loading or by pumping water into the caisson. Responses of suction caissons to pullout rates, aspect ratios, and extraction manners were examined. Test results show that a cone-shaped subsidence region occurs around the suction caisson during the suction-assisted installation. The pullout bearing capacity of the suction caisson in sand is dominated by the loading rate and the loading manner. For the suction caisson subjected to monotonic loading, the maximum bearing capacity is reached at the pullout rate of about 20.0?mm/s. The mobilized vertical displacement corresponding to the pullout capacity increases with increasing the pullout rate. The passive suction beneath the suction caisson lid reaches the maximum value when the pullout bearing capacity is mobilized. In addition, during the suction caisson extracted by pumping water into the caisson, the maximum pore water pressure in the caisson is obtained under the displacement of approximately 0.04 times the caisson diameter. The absolute values of the maximum pore water pressures for the suction caissons approximately equal those of the maximum vertical resistances at the monotonic pullout rate of 5 mm/s. When the vertical displacements of the suction caissons with the aspect ratio of 1.0 and 2.0 reach 0.92 and 1.77 times the caisson diameter, respectively, the seepage failure occurs around the caissons. Using a scaling method, the test results can be used to predict the time length required for the prototype suction caisson to be extracted from the seabed. 相似文献
12.
A series of model tests were conducted on Perspex-made suction caissons in saturated dense marine sand to study the sand plug formation during extraction. Suction caissons were extracted by pullout loading or by pumping air into the suction caisson. Effects of the pullout rates, aspect ratios and loading ways (monotonic or sustained) on the pullout capacity, and plug formation were investigated. It was found that the ultimate pullout capacity of the suction caisson increases with increasing the pullout rate. The sand plug formation under the pullout loading is significantly influenced by the pullout rate and the loading way. When the suction caisson is extracted at a relatively slow rate, the general sand boiling through the sand plug along the inner caisson wall occurs. On the contrary, the local sand boiling will occur at the bottom of the suction caisson subjected to a rapid monotonic loading or a sustained loading. Test results of the suction caisson extracted by pumping air into the caisson show that the pressure in the suction caisson almost follows a linear relationship with the upward displacement. The maximum pressures for suction caissons with aspect ratios of 1.0 and 2.0 during extraction by pumping air into the caisson are 1.70 and 2.27 times the maximum suction required to penetrate the suction caisson into sand. It was found that the sand plug moves downward during extraction by pumping air into the caisson and the variation in the sand plug height is mainly caused by the outflow of the sand particles from the inside of the suction caisson to the outside. When the suction caisson model is extracted under the pullout rate of 2?mm/s (0.28?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases to the maximum value with increasing the penetration depth and then reduces to zero. On the contrary, when extracted under the pullout rate of 10?mm/s (1.4?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases with increasing the pullout displacement. When extracted by pumping air into the caisson, the hydraulic gradient reaches the critical value, and at the same time, the seepage failure occurs around the suction caisson tip. 相似文献
13.
In the dynamic stability analysis of a caisson breakwater, most of current studies pay attention to the motion characteristics of caisson breakwaters under a single periodical breaking wave excitation. And in the lifetime stability analysis of caisson breakwater, it is assumed that the caisson breakwater suffers storm wave excitation once annually in the design lifetime. However, the number of annual severe storm occurrence is a random variable. In this paper, a series of random waves are generated by the Wen Sheng-chang wave spectrum, and the histories of successive and long-term random wave forces are built up by using the improved Goda wave force model. It is assumed that the number of annual severe storm occurrence is in the Poisson distribution over the 50-year design lifetime, and the history of random wave excitation is generated for each storm by the wave spectrum. The response histories of the caisson breakwater to the random waves over 50-year design lifetime are calculated and taken as a set of samples. On the basis of the Monte Carlo simulation technique, a large number of samples can be obtained, and the probability assessment of the safety of the breakwater during the complete design lifetime is obtained by statistical analysis of a large number of samples. Finally, the procedure of probability assessment of the breakwater safety is illustrated by an example. 相似文献
14.
In the dynamic stability analysis of a caisson breakwater, most of current studies pay attention to the motion characteristics of caisson breakwaters under a single periodical breaking wave excitation. And in the lifetime stability analysis of caisson breakwater, it is assumed that the caisson breakwater suffers storm wave excitation once annually in the design lifetime. However, the number of annual severe storm occurrence is a random variable. In this paper, a series of random waves are generated by the Wen Sheng-chang wave spectrum, and the histories of successive and long-term random wave forces are built up by using the improved Goda wave force model. It is assumed that the number of annual severe storm occurrence is in the Poisson distribution over the 50-year design lifetime, and the history of random wave excitation is generated for each storm by the wave spectrum. The response histories of the caisson breakwater to the random waves over 50-year design lifetime are calculated and taken as a set of samples. On the basis of the Monte Carlo simulation technique, a large number of samples can be obtained, and the probability assessment of the safety of the breakwater during the complete design lifetime is obtained by statistical analysis of a large number of samples. Finally, the procedure of probability assessment of the breakwater safety is illustrated by an example. 相似文献
15.
为推广应用新型弧面胸墙沉箱堤,结合模型试验和数值模拟对比分析了深水工况下弧面胸墙沉箱堤和削角胸墙沉箱堤的反射形态。波面和波压的数值结果与试验数据吻合良好,验证了数值方法的有效性。反射系数表明,入射波浪在与弧面胸墙沉箱堤相互作用过程中的能量损耗最小,其反射强于削角胸墙沉箱堤。波面和流速包络图显示,两种堤型均在堤前形成了部分立波系统,腹点和节点以四分之一波长的距离增量交替出现,胸墙和直立部分产生的反射波存在相位差,导致初始腹点的位置向海侧偏移。弧面胸墙沉箱堤前叠合波的相位差影响最小,腹点包络高度最大,节点包络高度最小,反射效应最明显。两种堤型前中下层水流的周期平均速度均较小且对称,表明底床泥沙不会产生趋势性输移,但迎浪基床上方的环流系统可能引起局部冲刷。相对而言,弧面胸墙沉箱堤前的环流强度最弱,更有利于冲刷防护。 相似文献
16.
Model tests were conducted to investigate the behaviour of caisson breakwater resting on sand beds subject to impacts due to wave breaking. The centrifuge modelling technique was employed to simulate the prototype stress levels in the foundation soil as the behaviour of sand is highly stress dependent. A wave actuator was developed to simulate the wave-breaking impact loads on the caisson during centrifuge flight. The test results reveal that the vertical and horizontal movements and tilt of the caisson breakwater increase progressively with the number of breaking-wave impacts. The excess pore pressures developed in the foundation sand under non-reversal loading are generally small and appear insignificant. The results of the parametric studies conducted to examine the effects of impact-load pattern, caisson width, rock berm beneath caisson, wave slamming on top slab of caisson and cyclic preloading on the performance of caisson breakwater are also presented. The practical implications of the experimental findings in the present study are also highlighted in this paper. 相似文献
17.
The assembly coastal hfilding technique initiated at home and abroad,is for a novel vertical standing harbor structure.Its main concept is the assembling components which can be combined and locked together to form a large caisson.Its application and future are discussed for a building.After many years of application and tests,the technique has a high stability,a wide range of application,low workload and fast construction speed.It can be widely applied in future for harbor engineering projects. 相似文献
18.
The suction caisson (or called suction anchor) which is considered as a relatively new type of foundation of offshore structures, has been extensively studied and applied for offshore wind turbines and oil platforms. The installation of the suction caisson is of great importance in the design and construction because it can bring about several issues and further influence the performance of holding capacity in safety service. In this paper, large deformation finite element (FE) analyses are performed to model the installation of suction caisson (SC) by suction and jacking in normally consolidated clay. The penetration of the suction caisson is modeled using an axisymmetric FE approach with the help of the Arbitrary Lagrangian–Eulerian (ALE) formulation which can satisfactorily solve the large deformation problem. The undrained shear strength of the clay and elastic modulus are varied with depth of soil through the subroutine VUFIELD. The numerical results allow quantification of the penetration resistance and its dependence on the installation method. The centrifuge test and theoretical solution are used for the FE model validation. After the validation, the penetration resistance, the soil plug heave, and the caisson wall friction have been examined through the FE model. Based on the numerical results, it is shown that the ALE technique can simulate the entire suction caisson penetration without mesh distortion problem. The installation method can play an important role on the penetration resistance, namely, the suction installation reduces the penetration resistance significantly compared to the purely jacked installation. With a further study on the suction case, it is found that as the final applied suction pressure increases, the soil plug heave increases, while the penetration resistance reduces with increase of the final suction pressure. The effect of the friction of internal caisson walls has been also investigated and a conclusion is drawn that internal wall friction has a significant contribution to the penetration resistance and it can be implicitly represented by varying coefficient of internal wall friction. As for the penetration resistance, both jacked and suction installation have great dependency on the internal wall friction. 相似文献