共查询到20条相似文献，搜索用时 595 毫秒
1.
为探究砂土液化的微观机理,根据室内试验中微生物反硝化反应气泡的生成速率,建立数值模拟的时效性关系,分别制取微生物处理0天、2天、3天和5天的高饱和砂土试样,采用CFD-DEM耦合方法模拟不同工况下砂土试样的循环三轴不排水剪切试验。依据砂土试样的力链分布、抗液化振次、孔压比、轴向应变和力学配位数在加载过程中的变化情况,从宏微观角度分析砂土试样的抗液化能力。模拟结果表明:含微生物气泡高饱和砂土的抗液化强度较饱和砂土有所提升;随着微生物处理时间的增加,砂土试样的饱和度降低,孔压比和轴向应变的累积变慢,抗液化能力增强。 相似文献
2.
采用MTS810动三轴试验仪,用二氧化碳+脱气水循环渗流法对重塑黄土进行饱和,进行了一系列对石碑塬滑坡区饱和黄土液化后变形特性试验。考虑干密度和初始有效围压对黄土液化后变形特性的影响,将液化与未液化黄土在单调静荷载作用下的应力-应变曲线进行对比。实验结果表明:利用二氧化碳+脱气水循环渗流法可以使重塑黄土饱和取得较好的效果;饱和石碑塬黄土具有明显的液化特征,在强震作用下发生液化,液化后强度大大衰减,应力-应变曲线呈弱硬化型,分为两个阶段;干密度和初始有效围压对液化后黄土的强度有一定影响,初始有效围压与不排水强度呈拟合度较高的线性关系,初始有效围压越高,液化后不排水强度越大。 相似文献
3.
Seismic base isolation effect in a liquefied sand layer was investigated based on soil properties measured in a series of undrained cyclic triaxial tests. Transmission of seismic wave in a soil model consisting of a liquefied surface layer and an underlying nonliquefied layer was analyzed in terms of energy, considering liquefaction-induced changes in S-wave velocity and internal damping. It was found that, between two different base-isolation mechanisms, a drastic increase in wave attenuation in the liquefied layer due to shortening wave length gives a greater impact on the base isolation with increasing thickness of the liquefied layer than the change of seismic impedance between the liquefied and nonliquefied layer. Also indicated was that cyclic mobility behavior in dilative clean sand tends to decrease the seismic isolation effect to a certain extent. 相似文献
4.
To understand the post-liquefaction behavior of liquefied ground, it is important to get a better understanding and a more suitable characterization of the variation of excess pore pressure after liquefaction. In this paper, the soil permeability is considered as one of the key soil parameters for clarifying the mechanism of post-liquefaction behavior of liquefied ground. For this reason, a series of shaking table tests were conducted for a Toyoura sand deposit with different soil permeability values. Polymer fluid was used in model tests to vary the permeability of sand deposits. Excess pore pressures and settlements were measured in each test. A basic mechanism in post-liquefaction behavior and the solidification phenomenon after liquefaction were discussed based on these test results. Also, a new method for predicting the dissipation of excess pore pressure was developed. This study provides evidence of the important effect of soil permeability on the velocity with which the solidification front moves upward in liquefied ground. It is suggested that the value of coefficient of permeability of liquefied sand can increase to about 4.0 times the initial value. This variation of permeability after liquefaction should be taken into account in post-liquefaction analysis. 相似文献
5.
Estimation of residual shear strength ratios of liquefied soil deposits from shear wave velocity 总被引：1，自引：1，他引：0
Pelinzener 《地震工程与工程振动(英文版)》2012,11(4):461-484
For sites susceptible to liquefaction induced lateral spreading during a probable earthquake, geotechnical engineers often need to know the undrained residual shear strength of the liquefied soil deposit to estimate lateral spreading displacements, and the forces acting on the piles from the liquefied soils in order to perform post liquefaction stability analyses. The most commonly used methods to estimate the undrained residual shear strength (Sur) of liquefied sand deposits are based on the correlations determined from liquefaction induced flow failures with SPT and CPT data. In this study, 44 lateral spread case histories are analyzed and a new relationship based on only lateral spread case histories is recommended, which estimates the residual shear strength ratio of the liquefiable soil layer from normalized shear wave velocity. The new proposed method is also utilized to estimate the residual lateral displacement of an example bridge problem in an area susceptible to lateral spreading in order to provide insight into how the proposed relationship can be used in geotechnical engineering practice. 相似文献
6.
Critical state soil mechanics is a useful framework to understand sand behavior. In this paper, a relationship is developed for estimating undrained critical shear strength of sands based on the critical state framework. The relationship is validated by comparison with laboratory test results and sand liquefied strength from field liquefaction failure case histories. Using this relationship, the influence of fines content on undrained critical shear strength is studied for different combinations of effective stress and density. The parametric study indicates that depending on soil void ratio, effective stress, and the shape and mineralogy of the fine particles, undrained critical strength may increase, remain the same, or decrease as the amount of fines content increases. Both the susceptibility to liquefaction and the severity of strain-softening are affected by adding fines. It is suggested that the critical state parameter is inadequate for describing the behavior of liquefiable sands and sand shearing-compressibility should be taken into account in liquefaction analysis. 相似文献
7.
黄土具有极强的水敏性和动力易损性，黄土地区多次强震都引起过液化、滑坡等地质灾害，造成了严重的人员伤亡和财产损失，因此振动作用下高含水率黄土的液化问题不容忽视。在大量已有研究的基础上，以宁夏党家岔滑坡为例，研究振动作用下高含水率黄土的液化问题。现场调查发现高含水率滑带土并未达到完全饱和状态（饱和度达95%左右），在新鲜的芯样断面发现有明显的"流态化"液化破坏特征。借助室内试验和数值模拟技术，对党家岔滑坡非饱和黄土层的液化性能及液化发生机理进行分析。结果表明：（1）非饱和黄土层液化发生机理可概括为：地震作用下饱和黄土层孔隙水压力激增，高含水率非饱和黄土层孔压增长响应滞后，随着孔隙水压朝上部消散，地下水向上渗流，当平均有效应力接近0时，高含水率非饱和黄土层发生液化；（2）振动过程中不同饱和度黄土孔隙水压力增长响应具有滞后性，借鉴饱和黄土液化时孔压比的判别标准和Seed简化判别法，初步证实党家岔滑坡高含水率非饱和黄土层可发生振动液化，斜坡前缘和中部土体发生液化的初始饱和度范围分别为68.3%~100%和73.8%~100%，斜坡后缘土体不发生液化。 相似文献
8.
2011年2月22日,新西兰第二大城市克赖斯特彻市附近发生Ms6.3级地震,震中位于克赖斯特彻市西南10km处,震源深度为5km。地震造成了大量的人员伤亡和经济损失,重建费用估计高达40亿新西兰元,得到共识是砂土液化为震害主因。此次地震,液化震害极为严重,喷砂冒水范围广泛分布于城市内外,引起大量次生灾害,地震也为砂土液化特征研究,特别是检验和发展液化判别方法提供了大量宝贵的液化数据。本文收集整理震后132个勘察点的勘察资料,包括静力触探试验（以下简称"CPT"）数据、地表峰值加速度和地下水位等。通过对数据的研究,得到了地震液化场地加速度分布、地下水位分布和砂层埋深分布等特征。检验了我国现有的静力触探试验液化判别方法,结果表明:液化场地主要分布在PGA为0.5~0.65g附近,液化层5m以内居多,我国CPT液化判别方法对于10m以下判别存在明显的错误,同时此次地震还发现多个液化层位于20m以下,对于这个深度,国内CPT液化判别方法还未涉猎。 相似文献
9.
辽宁台安砂土属于易液化砂,提升其抗液化性能具有重要的工程意义。文章针对纳米硅溶胶(CS)对辽宁台安砂土抗液化性能的改良效果进行探究,通过不排水动三轴试验,对纯砂样和改良砂样的液化特性进行对比研究,分析CS浓度和固化时间两个参量对改良砂样动力特性的影响。研究结果表明：(1)CS能够显著提升台安砂土的抗液化性能,在动载作用下改良砂样均未发生液化破坏。(2)随CS浓度和固化时间的增加,试样动孔压ud、动应变εd呈现先迅速下降后趋于平缓的发展规律;当CS浓度增至4%、固化时间达到3周后,试样抗液化性能的提升效果不再明显。(3)改良砂样的滞回曲线变得更加稳定。随CS浓度增加,阻尼先降低后趋于稳定,动弹性模量逐渐增大并趋于平缓,但伴随有一定的波动;随固化时间增大,阻尼呈减小趋势,动弹性模量呈增大趋势。研究成果可为辽宁台安地区砂土液化治理提供参考依据。 相似文献
10.
11.
Gonghui Wang Runqiu Huang Masahiro Chigira Xiyong Wu Sérgio D. N. Lourenço 《地球表面变化过程与地形》2013,38(3):265-274
Here, we propose that an earthquake can trigger the failure of a landslide mass while simultaneously triggering liquefaction of runout‐path materials before the arrival of the landslide mass, thus greatly increasing the size and mobility of an overriding landslide. During the 2008 Wenchuan earthquake, about 60 000 landslides were triggered, directly resulting in about 20 000 casualties. While these landslides mainly originated from steep slopes, some landslides with high mobility formed in colluvial valley deposits. Among these, the most catastrophic was the Xiejiadian landslide in Pengzhou city, which traveled hundreds of meters before coming to rest. Through field investigation and laboratory testing, we conclude that this landslide primarily formed from colluvial deposits in the valley and secondarily from failure of slopes in granitic rock located uphill. Much of the granitic slope failure was deposited in the upper part of the travel path (near the slide head); the remainder was dispersed throughout the main landslide deposit. Superposition of deposits at the landslide toe indicates that landslide debris derived from colluvial soil was deposited first. The deposits at the landslide toe displayed flow characteristics, such as fine materials comprising basal layers and large boulders covering the deposit surface. We hypothesize that the main part of the landslide resulted from seismogenic liquefaction of valley colluvium, rather than from liquefaction potentially caused by undrained loading from the granitic slope failures impacting the colluvium. To examine the likelihood that seismogenic liquefaction occurred, we took samples from different areas of the landslide deposit and performed undrained cyclic shear tests on them in the laboratory. The results showed that the sandy soils that comprise most of the deposit are highly liquefiable under seismic loading. Therefore, we conclude that liquefaction of the colluvium in the valley during the earthquake was the main reason for this rapid (~46 m/s) long‐runout (1·7 km) landslide. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
12.
Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels. 相似文献
13.
The coupled mechanics of fluid-filled granular media controls the physics of many Earth systems, for example saturated soils, fault gouge, and landslide shear zones. It is well established that when the pore fluid pressure rises, the shear resistance of fluid-filled granular systems decreases, and, as a result, catastrophic events such as soil liquefaction, earthquakes, and accelerating landslides may be triggered. Alternatively, when the pore pressure drops, the shear resistance of these geosystems increases. Despite the great importance of the coupled mechanics of grain–fluid systems, the basic physics that controls this coupling is far from understood. Fundamental questions that must be addressed include: what are the processes that control pore fluid pressurization and depressurization in response to deformation of the granular skeleton? and how do variations of pore pressure affect the mechanical strength of the grains skeleton? To answer these questions, a formulation for the pore fluid pressure and flow has been developed from mass and momentum conservation, and is coupled with a granular dynamics algorithm that solves the grain dynamics, to form a fully coupled model. The pore fluid formulation reveals that the evolution of pore pressure obeys viscoelastic rheology in response to pore space variations. Under undrained conditions elastic-like behavior dominates and leads to a linear relationship between pore pressure and overall volumetric strain. Viscous-like behavior dominates under well-drained conditions and leads to a linear relationship between pore pressure and volumetric strain rate. Numerical simulations reveal the possibility of liquefaction under drained and initially over-compacted conditions, which were often believed to be resistant to liquefaction. Under such conditions liquefaction occurs during short compactive phases that punctuate the overall dilative trend. In addition, the previously recognized generation of elevated pore pressure under undrained compactive conditions is observed. Simulations also show that during liquefaction events stress chains are detached, the external load becomes completely supported by the pressurized pore fluid, and shear resistance vanishes. 相似文献
14.
循环荷载作用下饱和砂土的孔压增长规律是土动力学的核心内容之一。基于笔者在给定相对密度、均等固结条件下饱和南京细砂的不排水等幅循环三轴试验结果建立的孔压增量模型,进一步进行了不同相对密度、不同固结比条件下饱和南京细砂的不排水等幅循环三轴试验,将上述均等固结的孔压增量模型拓展为适用于不同相对密度、均等和非均等固结条件的孔压增量模型。采用拓展后的孔压增量模型对试验结果进行分析的结果表明：通过该孔压增量模型预测验证试验的孔压与验证试验测试的孔压具有较好的一致性,说明该孔压增量模型具有普适性。 相似文献
15.
桥台在桥梁系统中占据重要位置,桥台的稳定性直接影响到桥梁的抗震性能。在国内外大量震害中发现大量由桥台破坏引起的桥梁损坏,而且这些破坏常常伴随着由于液化引起的地面大变形。为研究液化场地中桥台滑坡机理,采用完全耦合的有效应力分析方法,利用修正的PasterZienkiewicz Mark-Ⅲ模型来模拟砂土在地震荷载作用下的液化特性。研究台顶梁重和液化层位置对桥台位移的影响,并分析夯实作用对砂土液化的影响。结果表明:模拟得出结果与振动台试验结果基本一致,而且简单的夯实不能降低砂土液化的风险。 相似文献
16.
利用GDS循环三轴仪进行一系列饱和砂砾土不排水动三轴液化试验,研究其在循环荷载作用下的液化特性,分析含砾量对饱和砂砾土动强度和动孔压的影响规律。研究表明:含砾量对砂砾土液化性能影响较大,随着含砾量的增加砂砾土抗液化强度呈单调增加趋势;随循环周次的增加孔隙水压力不断升高,增长速率与所施加的循环应力幅值有关,同一固结压力下,振次比相同时循环动应力幅值越大动孔压比越大;破坏振次对动孔压增长模式存在影响,破坏振次较小时砂砾土动孔压增长模式呈双曲线型发展,破坏振次较大时砂砾土的动孔压增长模式可用反正弦函数来表示,且含砾量越大循环荷载引起的孔隙水压力越高;含砾量对砂砾土液化特性的影响可从砂砾土的微细观结构特征得到阐释,并借助其粒间状态参量进行分析。 相似文献
17.
ugh the sinusoid loading dynamic triaxial test, the liquefaction property of saturated loess and sand selected from a civil airport of Lanzhou, Gansu is examined. Based on the laboratory results, a comprehensive assessment on the earthquake liquefaction potential of the loess and sand is given, using the liquefaction resistance shear stress method and the results of seismic hazard assessment. It is found that under the effect of ground motion with exceedance probability of 10% within 50 years, the loess in the study is more susceptible to liquefaction than sand. 相似文献
18.
19.
循环剪切吸水条件下饱和砂土的应力应变规律 总被引：1，自引：0，他引：1
在实际土工抗震边值问题中,饱和砂土在许多情况下并非处于完全不排水条件,可能由于土性等因素的不同而出现各异的排渗条件。排水条件对土体的动力应力应变响应有较大影响,本文基于新开发的孔隙水注入控制系统,进行了循环剪切条件下饱和砂土吸水试验,研究了剪切吸水对土体动力特性的影响规律。通过试验发现:剪切吸水条件下砂土的抗液化强度较不排水条件下降低,同样的循环剪切条件下轴向应变发展更大;试样的抗液化强度降低和轴向应变增加程度随剪切吸水率的增大而增加。基于对饱和砂土体变规律的已有研究,本文初步解释了剪切吸水条件下饱和砂土应力应变特性规律的物理实质。 相似文献
20.
Pre-shear history has been shown to be a critical factor in the liquefaction resistance of sand. By contrast to prior experimental studies in which triaxial shear tests were used to examine the effects of pre-shear on the liquefaction resistance of sand, hollow cylinder torsional shear tests were used in this study to avoid the influence of the inherent anisotropy that is inevitably produced during the sample preparation process because of gravitational deposition. A series of cyclic undrained shear tests were performed on sand samples that had experienced medium to large pre-shear loading. The test results showed that the liquefaction resistance of sand can be greatly reduced by its pre-shear history, and a pre-shear strain within the range from 0.1% to 5% can cause sand to be more prone to liquefaction. During the cyclic shear tests, the samples that had experienced pre-shear loading exhibited different behaviors when cyclic shear loading started in different directions, i.e., the clockwise direction and the counterclockwise direction. If the cyclic loading started in the identical direction as the pre-shear loading, then the mean effective stress of the sand was almost unchanged during the first half of the loading cycle; if the cyclic loading started in the direction opposite to that of the pre-shear loading, then the mean effective stress decreased significantly during the first half of the loading cycle. However, this anisotropic behavior was only remarkable during the first loading cycle. From the second cycle onward, the speeds of the decrease in the mean effective stresses in the two types of shear tests became similar. 相似文献