共查询到20条相似文献，搜索用时 671 毫秒
1.
水力压裂是页岩油气增产的主要手段,其核心是向储层连续泵入压裂液迫使储层产生水力裂缝/缝网形成油气运移高效通道,从而达到油气增产的目的。相较人工主缝,微裂缝具有数量大、缝宽小、走向复杂等特点,常规支撑剂无法对其形成有效支撑,如何提高微裂缝的导流能力是进一步提高页岩油气产能的关键。微缝导流能力实验表明:微支撑剂嵌入页岩裂缝表面导致一定程度的渗透率损害,但支撑微裂缝的渗透率仍比页岩基质渗透率高出2～3个数量级,仍可为页岩油气运移提供有效渗流通道。本文系统分析了微支撑剂对微裂缝的支撑特性、微支撑剂的长距离输运性能及辅助降滤等特征,提出了微支撑剂对致密油气增产的内在机制。结合我国致密油气储层基质孔隙尺度,形成了考虑微裂缝开度及基质孔隙尺寸的微支撑剂选配原则。 相似文献
2.
断层对页岩气储层压裂改造有重要影响,甚至诱发深部地震事件和近地表环境问题。本文采用多物理场耦合方法,基于渗流和应力耦合理论,研究储层水力压裂过程中断层以及封闭顶板中水力破坏区域的产生与演化机理,并分析讨论流体沿高渗通道运移扩散机理,研究结果表明:(1)断层改变储层水力破坏区域形态并且扩展了水力压裂破坏空间。较高注水压力使储层水力破坏区域扩大到封闭顶板和底板,水力破坏区域受断层影响而沿着断层带快速发育延伸。高注水压力导致断层水力压裂破坏高度急剧增加,储层封闭性发生改变。(2)在页岩储层高风险地质构造和较高注水压力条件下,水力压裂作业产生岩石破裂和裂缝局部活化诱发的微地震事件,但难以导致破坏性地震事件,多属于断层或较大断裂局部区域产生的水力耦合破坏及可能诱发的较小地震事件。(3)水力破坏区域贯通到断层带内诱发流体沿断层带迁移,断层带的渗透率较高,水力破坏区域与上部高渗透岩层贯通会加快流体的逃逸速度,增大压裂液污染上部地层的风险,导致压裂效率降低,影响储层压裂改造,降低了页岩气开发价值。 相似文献
3.
Hydrocarbon production from shale has attracted much attention in the recent years. When applied to this prolific and hydrocarbon rich resource plays, our understanding of the complexities of the flow mechanism(sorption process and flow behavior in complex fracture systems- induced or natural) leaves much to be desired. In this paper, we present and discuss a novel approach to modeling, history matching of hydrocarbon production from a Marcellus shale asset in southwestern Pennsylvania using advanced data mining, pattern recognition and machine learning technologies. In this new approach instead of imposing our understanding of the flow mechanism, the impact of multi-stage hydraulic fractures, and the production process on the reservoir model, we allow the production history, well log, completion and hydraulic fracturing data to guide our model and determine its behavior. The uniqueness of this technology is that it incorporates the so-called "hard data" directly into the reservoir model, so that the model can be used to optimize the hydraulic fracture process. The "hard data" refers to field measurements during the hydraulic fracturing process such as fluid and proppant type and amount, injection pressure and rate as well as proppant concentration. This novel approach contrasts with the current industry focus on the use of "soft data"(non-measured, interpretive data such as frac length, width,height and conductivity) in the reservoir models. The study focuses on a Marcellus shale asset that includes 135 wells with multiple pads, different landing targets, well length and reservoir properties. The full field history matching process was successfully completed using this data driven approach thus capturing the production behavior with acceptable accuracy for individual wells and for the entire asset. 相似文献
4.
页岩气的工业化开发要求对致密储层进行体积压裂改造,水平井多级分段压裂技术是成功开发页岩气藏的关键技术之一。页岩储层在地应力与致裂压力联合作用下突破页岩基质,沟通天然裂隙等弱结构面,形成高导流能力缝网系统,页岩储层中赋存的游离气和吸附气得以释放,提高了页岩气井的初始产量和最终采收率。根据渝东地区页岩储层工程地质特征,结合渝页A-2HF井、渝页B-2HF井矿场压裂施工数据,探索适用于渝东地区的页岩储层压裂工艺技术,结果表明,采用前置盐酸处理储层保持近井带导流能力,能够保障后续大排量施工压力窗口;低砂比粉砂段塞多级降滤实现“控近扩远”,增加储层改造体积;压力异常层段胶液前置充分造缝,可为后续滑溜水携带支撑剂进入地层创造有利条件。 相似文献
5.
在页岩气水力压裂开发领域中,压裂液注入排量对裂缝网络的扩展形态具有显著影响。而页岩储层中的随机天然裂缝,会给水力压裂的参数敏感性分析带来不同程度的干扰。首先,根据页岩储层裂缝发育特征,制备了包含3组正交预制裂缝的混凝土试样;然后,采用真三轴压裂系统,对试样进行三向应力加载模拟地应力环境,并以恒定排量向其内部注入流体;最后,将单位体积裂缝面积P 32作为体积压裂指标,来定量描述排量对压裂缝网扩展形态的影响。试验结果表明:（1）在块体单元边长较小（即预制裂缝密度较大）的试样中,体积压裂的效果更加显著;（2）小排量压裂液所产生的裂缝一般是激活的预制裂缝,而中排量和高排量压裂液可以使已激活的预制裂缝发生偏转,在混凝土基质中重新开启水力裂缝,从而增加裂缝网络的复杂性;（3）随着排量的增加,试样压裂后的P 32值会升高;但排量增加到一定程度后,P 32值不再增长,甚至略微下降。 相似文献
6.
In this study, the effects of the temperature difference between hydraulic fracturing fluid and rock formation on the time‐dependent evolution of fracture width were investigated using a newly derived one‐dimensional anisotropic porothermoelastic analytical solution. The solution is shown to correctly reproduce existing solutions for special cases and corrections for an earlier publication are provided. An analysis of time‐dependent fracture width evolution using Woodford Shale data was also presented. It was found that when the fracturing fluid has the same temperature as the shale formation, the fracture gradually closes back after the initial opening due to the invasion of the fracturing fluid. Practically, in this scenario, proppants should be pumped into the fracture as soon as possible to obtain maximum fracture conductivity. On the other hand, with a fracturing fluid 60 °C colder than the formation, the thermal contraction of the rock dominates the fracture aperture evolution, resulting in a fracture aperture approximately 70% larger than that produced by the hotter fracturing fluid. Consequently, in this case, it is beneficial to delay proppant placement to take advantage of the widening fractures. Finally, it was found that the fracture aperture is directly controlled by the spacing of natural fractures. Therefore, the presence of natural fractures in the shale formation and their spacing influence not only the type of hydraulic fractures created but also what kind and size of proppants should be used to keep them open. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
7.
Generally, induced hydraulic fractures are generated by fluid overpressure and are used to increase reservoir permeability through forming interconnected fracture systems. However, in heterogeneous and anisotropic rocks, many hydraulic fractures may become arrested or offset at layer contacts under certain conditions and do not form vertically connected fracture networks. Mechanical layering is an important factor causing anisotropy in sedimentary layers. Hence, in this study, with a shale gas reservoir case study in the Longmaxi Formation in the southeastern Chongqing region, Sichuan Basin, we present results from several numerical models to gain quantitative insights into the effects of mechanical layering on hydraulic fracturing. Results showed that the fractured area caused by hydraulic fracturing indicated a linear relationship with the neighboring layer’s Young’s modulus. An increase of the neighboring layer’s Young’s modulus resulted in better hydraulic fracturing effects. In addition, the contact between two neighboring layers is regarded as a zone with thickness and mechanical properties, which also influences the effects of hydraulic fracturing in reservoirs. The initial hydraulic fracture was unable to propagate into neighboring layers under a relatively low contact’s Young’s modulus. When associated local tensile stresses exceeded the rock strength, hydraulic fractures propagated into neighboring layers. Moreover, with the contact’s Young’s modulus becoming higher, the fractured area increased rapidly first, then slowly and finally became stable. 相似文献
8.
The production efficiency of shale gas is affected by the interaction between hydraulic and natural fractures. This study presents a simulation of natural fractures in shale reservoirs, based on a discrete fracture network (DFN) method for hydraulic fracturing engineering. Fracture properties of the model are calculated from core fracture data, according to statistical mathematical analysis. The calculation results make full use of the quantitative information of core fracture orientation, density, opening and length, which constitute the direct and extensive data of mining engineering. The reliability and applicability of the model are analyzed with regard to model size and density, a calculation method for dominant size and density being proposed. Then, finite element analysis is applied to a hydraulic fracturing numerical simulation of a shale fractured reservoir in southeastern Chongqing. The hydraulic pressure distribution, fracture propagation, acoustic emission information and in situ stress changes during fracturing are analyzed. The results show the application of fracture statistics in fracture modeling and the influence of fracture distribution on hydraulic fracturing engineering. The present analysis may provide a reference for shale gas exploitation. 相似文献
9.
Researchers have recently realized that the non-tectonic natural fractures are developed in shale formations and significant for the exploitation of shale gas. Studies have shown that the tectonic fractures in naturally fractured reservoirs have influences on the maximization of stimulated reservoir volume (SRV) during hydraulic fracturing. However, the effect of the non-tectonic randomly natural fractures on the fracturing network propagation is not well understood. Laboratory experiments are proposed to study the evolution of fracturing network in naturally fractured formations with specimens that contain non-tectonic random fractures. The influences of the dominating factors were studied and analyzed, with an emphasis on natural fracture density, stress ratio, and injection rate. The response surface methodology was employed to perform the multiple-factor analysis and optimization in the maximization of the SRV. A sensitivity study reveals a number of interesting observations resulting from these parameters on the fracturing network evaluation. It is suggested from the geometry morphology of fracturing network that high natural fracture density and injection rate tend to maximize the fracturing network. The influence of stress contrast on fracturing network is nonlinear; an optimal value exists resulting in the best hydraulic fracturing effectiveness. 相似文献
10.
页岩储层天然裂缝、水平层理发育,水力压裂过程中可能形成复杂的体积裂缝。针对页岩储层体积裂缝扩展问题,基于流-固耦合基本方程和损伤力学原理,建立了页岩储层水力压裂体积裂缝扩展的三维有限元模型。将数值模型的模拟结果与页岩储层裂缝扩展室内试验结果进行对比,二者吻合较好,从而证明了数值模型的可靠性。通过一系列数值模拟发现：（1）水力压裂过程中水平层理可能张开,形成水平缝,水平与垂直缝相互交错,形成复杂的体积裂缝网络;（2）水平主应力差增大,体积裂缝的分布长度（水平最大主应力方向压裂裂缝的展布距离）增加、分布宽度（水平最小主应力方向压裂裂缝的展布距离）减小,体积裂缝的长宽比增加;（3）压裂施工排量增大,体积裂缝的分布长度减小、宽度增加,压裂裂缝的长宽比降低;（4）天然裂缝的残余抗张强度增大,体积裂缝分布宽度减小、分布长度增加,体积裂缝的长宽比增加。研究成果可以为国内的页岩气的压裂设计和施工提供一定的参考和借鉴。 相似文献
11.
微地震监测技术是页岩气开采过程中对页岩气储层压裂效果评价和指导压裂过程的重要手段,可通过观察、分析压裂过程中诱发微地震事件,获取压裂裂缝参数、导流能力、裂缝展布发育方向等信息。中牟区块牟页1井具有低孔、低渗储层特征,对含气层段的三层储层,采用大排量水力压裂施工,进行地面微地震监测、井中微破裂成像技术压裂监测及微地震监测;牟页1井监测压裂结果显示为缝长251～496m,缝宽120～252m,改造体积约为237.5×104～387.7×104 m3,方位角64°～80°。压裂实施使储层裂缝开启含气层段得到改造,指导了实时压裂和压裂效果评价。 相似文献
12.
页岩储层孔隙度和渗透率极低,天然裂缝和水平层理发育,常规压裂增产措施无法满足页岩气的开发要求,水平井多段分簇压裂是页岩气开发的关键技术之一,该技术能够大幅度提升压裂改造的体积、产气量和最终采收率。为确定页岩储层水平井多段分簇射孔压裂的起裂点和起裂压力,采用有限元方法建立了水平井套管完井（考虑水泥环和套管的存在）多段分簇射孔的全三维起裂模型。数值模型的起裂压力与室内试验结果吻合较好,证明了数值模型的准确性和可靠性。利用数值模型研究了页岩水平井多段分簇射孔压裂的起裂点和起裂压力的影响因素,研究发现：射孔孔眼附近无天然裂缝或水平层理影响,起裂点发生在射孔簇孔眼的根部;射孔簇间距越小,中间射孔簇的干扰越大,可能造成中间的射孔簇无法起裂;射孔密度和孔眼长度增大,起裂压力降低;天然裂缝的存在,在某些情况能够降低起裂压力且改变起裂位置,主要与天然裂缝的分布方位及水平主应力差有关;水平层理可能会降低起裂压力,但与垂向主应力与水平最小主应力的差值有关。获得的起裂压力变化规律,可作为进一步研究水平井多段分簇射孔条件下的裂缝扩展规律的基础,可以为压裂设计和施工的射孔参数确定及优化给出具体建议。 相似文献
13.
Although hydraulic fracturing has been massively studied and applied as a key technique to enhance the gas production from tight formations, some problems and uncertainties exist to accurately predict and analyze the fracture behavior in complex reservoirs, especially in the naturally fractured reservoirs like shale reservoirs. This paper presents a full 3D numerical model (FLAC3D) to study hydraulic fracturing behavior under the impact of preexisting orthogonal natural fractures. In this numerical model, the hydraulic fracture propagation direction is assumed perpendicular to the minimum principal stress and activated only by tensile failure, whereas the preexisting natural fractures can be activated by tensile or shear failure or a combination of them, and only tensile failure can open the natural fracture as well. The newly developed model was used to study the impact of preexisting orthogonal natural fractures on hydraulic fracturing behavior, based on a multistage hydraulic fracturing operation in a naturally fractured reservoir from the Barnett Shale formation, northwest of Texas in USA. In this multistage operation, two more representative stages, i.e., stage 1 with a relatively large horizontal stress anisotropy of 3.3 MPa and stage 4 with a comparatively small one of 1.3 MPa, were selected to conduct the simulation. Based on the numerical results, one can observe that the interaction between hydraulic and natural fracture is driven mainly by induced stress around fracture tip. Besides, the horizontal stress anisotropy plays a key role in opening the natural fracture. Thus, no significant opened fracture is activated on natural fracture in stage 1, while in stage 4 an opened fracture invades to about 90 m into the first natural fracture. Conversely, the hydraulic fracture length in stage 1 is much longer than in stage 4, as some fluid volume is stored in the opened natural fracture in stage 4. In this work, the shear failure on natural fractures is treated as the main factor for inducing the seismic events. And the simulated seismic events, i.e., shear failure on natural fractures, are very comparable with the measured seismic events. 相似文献
14.
采用真三轴物理模型试验机、水力压裂伺服系统、声发射定位系统以及压裂液中添加示踪剂等方式,在真三轴条件下对大尺寸页岩水平井进行了水力压裂物理模拟试验,通过裂缝的动态监测和压裂后剖切等分析了裂缝的扩展规律,并对页岩压裂缝网的形成机制进行了初步探讨。结果表明：（1）水力裂缝自割缝处起裂并扩展、压开或贯穿层理面,形成相对较复杂的裂缝形态;（2）裂缝中既有垂直于层理面的新生水力主裂缝,又有沿弱层理面扩展延伸的次级裂缝,形成了纵向和横向裂缝并存的裂缝网络;（3）水力裂缝在延伸过程中会发生转向而逐渐垂直最小主应力;（4）水力裂缝在扩展过程中遇到弱层理面时的止裂、分叉、穿过和转向现象是形成页岩储层复杂裂缝网络的主要原因,而弱结构面的大量存在是形成复杂裂缝的基础。其研究结果可为页岩气藏水平井分段压裂开采等提供有力技术支持。 相似文献
15.
页岩气藏矿场压裂实践表明,储层有效改造体积（effective stimulated reservoir volume,简称ESRV）是影响页岩气藏体积压裂水平井生产效果的关键因素,ESRV的准确计算对页岩气藏压裂方案评价与体积压裂水平井产量预测具有重要作用.基于页岩储层改造体积（stimulated reservoir volume,简称SRV）多尺度介质气体运移机制,建立了SRV区域正交离散裂缝耦合双重介质基质团块来表征单元体渗流模型（representation elementary volume,简称REV）,并结合北美页岩储层实例研究了次生裂缝间距、宽度等缝网参数对页岩气藏气体运移规律的影响.在此基础上根据SRV区域次生裂缝分布特征,采用分形质量维数定量表征裂缝间距分布规律,结合页岩气藏次生裂缝间距对基质团块内流体动用程度的影响规律,得到了页岩气藏体积压裂ESRV计算方法.结果表明SRV区域次生裂缝间距对基质团块内吸附及自由气影响较大,次生裂缝间距小于0.20 m时可以实现SRV区域基质团块内流体向各方向裂缝的"最短距离"渗流.选取北美典型页岩储层生产井体积压裂数据进行ESRV计算,页岩气藏目标井ESRV占体积压裂SRV的37.78%.因此ESRV受改造区域次裂缝分布规律及SRV有效裂缝间距界限的影响,是储层固有性质及人工压裂因素综合作用的结果. 相似文献
16.
西部挤压盆地内低渗性含油气砂泥岩储层构造运动期次多、埋藏深度大、泥质夹层多、高角度网状缝继承性发育,裂缝不仅是油气的有效运移通道,也是储层压裂开发效果的主要影响因素。选择西部天山山前某区块深层砂泥岩裂缝性气藏为研究区,以裂缝形成机制的探讨和研究为突破点,在岩心观察、CT层析成像扫描、成像测井解释的基础上,精细统计裂缝产状、开度、充填度,结合流体包裹体及古应力场划分裂缝发育期次,最后总结继承性裂缝的发育模式。研究结果表明,砂泥岩储层裂缝继承性缝的有利发育条件为多期次构造运动、低应力差、低逼近角度、适当泥质含量或低摩擦因数,岩性是内因,构造应力是外因。 相似文献
17.
Hydraulic fracturing is an essential technology for the development of unconventional resources such as tight gas. The evaluation of the fracture performance and productivity is important for the design of fracturing operations. However, the traditional dimensionless fracture conductivity is too simple to be applied in real fracturing operations. In this work, we proposed a new model of dimensionless fracture conductivity (FCD), which considers the irregular fracture geometry, proppant position and concentration. It was based on the numerical study of the multistage hydraulic fracturing and production in a tight gas horizontal well of the North German Basin. A self-developed full 3D hydraulic fracturing model, FLAC3Dplus, was combined with a sensitive/reliability analysis and robust design optimization tool optiSLang and reservoir simulator TMVOCMP to achieve an automatic history matching as well as simulation of the gas production. With this tool chain, the four fracturing stages were history matched. The simulation results show that all four fractures have different geometry and proppant distribution, which is mainly due to different stress states and injection schedule. The position and concentration of the proppant play important roles for the later production, which is not considered in the traditional dimensionless fracture conductivity FCD. In comparison, the newly proposed formulation of FCD could predict the productivity more accurately and is better for the posttreatment evaluation. 相似文献
18.
储层岩体中的天然结构面对水力压裂缝网改造具有重要的影响。本文采用真实破裂过程分析软件RFPA2D-Flow,在考虑岩体非均质性和岩体渗流-应力-损伤破裂特性的基础上,对不同尺度天然结构面影响的水力压裂裂缝扩展与演化行为进行了模拟分析和讨论,研究结果表明:（1）当水力裂缝遇天然非闭合裂隙时,在水力裂缝靠近非闭合裂隙区间形成拉张应力区,水力裂缝与区间非闭合裂隙间微元体累进性张拉破坏是导致水力裂缝与非闭合裂隙贯通的主要机制;（2）层理等优势结构对水力压裂裂缝扩展及缝网形态影响十分显著,当最大主应力方向与层理面走向小角度相交时,层理结构面对水力裂隙的扩展起主要作用,当最大主应力方向与层理面走向大角度相交时,最大主压应力与层理面共同对缝网扩展起主导作用,随着优势结构面的增多和差应力的增大,水力压裂形成的缝网范围和复杂性程度随之增大;（3）储层水力压裂是一种局部范围内的短暂动力扰动过程,尽管断层的存在可以极大地影响水力裂缝的扩展模式,增大水力裂隙扩展高度,但相比于储层埋深,水力压裂对断层封闭性的破坏范围和断层活动性的扰动程度十分有限。 相似文献
19.
3500 m以深页岩气资源量占整个川南地区总资源量的比例高达86.5%,该区深层页岩气藏构造复杂,压裂形成复杂缝网的难度大,有必要通过数值模拟研究深层页岩气复杂缝网主控因素,对实现川南地区深层页岩气的效益开发具有重要意义。在对川南地区页岩气气田某井的岩芯进行细观尺度下的观察并构建二维裂缝模型的基础上,利用位移间断边界元法(DDM)模拟深层页岩水力压裂过程中水力裂缝与天然裂缝相互作用的物理力学过程,研究主应力、应力差和压裂液排量对裂缝扩展的影响。结果表明:在高应力差条件下缝网的复杂程度和总长度急剧降低,缝网的平均宽度增大,且平均宽度随排量增加而增大的能力变得有限。在高应力差条件下提升压裂液排量,缝网长度的增加以产生新生裂缝为主,同时提升排量对于激活天然裂缝有一定的提升作用,但是效果有限。相比于拉张裂缝,剪切裂缝的形成受主应力和压裂液排量的影响更显著,在高应力差条件下缝网中剪切裂缝的长度急剧降低。随着压裂液的注入,在较低应力差和相同压裂液注入量的情况下,低排量工况下的裂缝长度逐渐大于高排量工况下的裂缝长度。在应力差较高的情况下裂缝扩展的速率较低,同时会使提升排量而形成更多新生裂缝的能力变得有限。基于显微镜观察构建的裂缝模型计算出的结果能够较好地符合场地实际,为深层水力压裂设计和施工提供参考。 相似文献
20.
This communication investigates the effects fo the non-Newtonian behaviour of the fracturing fluids in the hydraulic fracturing mechanism. These effects are illustrated on the propagation of a vertical hydraulic fracture into an oil reservoir, in which the fracturing fluid is of power law and of pseudo-plastic type. The analytical solutions for evaluating the fracture lengrhs are presented for the cdases of large fluid loss and for no fiuid loss. The results obtained should be useful in the design of fracture treatments, permitting the finding of the rheological properties of the injected fluid for obtaining the desired fracture length and width. 相似文献
|
