共查询到20条相似文献，搜索用时 31 毫秒
1.
It is well known that soil is inherently anisotropic and its mechanical behavior is significantly influenced by its fabric anisotropy. Hypoplasticity is increasingly being accepted in the constitutive modeling for soils, in which many salient features, such as nonlinear stress-strain relations, dilatancy, and critical state failure, can be described by a single tensorial equation. However, within the framework of hypoplasticity, modeling fabric anisotropy remains challenging, as the fabric and its evolution are often vaguely assumed without a sound basis. This paper presents a hypoplastic constitutive model for granular soils based on the newly developed anisotropic critical state theory, in which the conditions of fabric anisotropy are concurrently satisfied along with the traditional conditions at the critical state. A deviatoric fabric tensor is introduced into the Gudehus-Bauer hypoplastic model, and a scalar-valued anisotropic state variable signifying the interplay between the fabric and the stress state is used to characterize its impact on the dilatancy and strength of the soils. In addition, fabric evolution during shearing can explicitly be addressed. Modifications have also been undertaken to improve the performance of the undrained response of the model. The anisotropic hypoplastic model can simulate experimental tests for sand under various combinations of principle stress direction, intermediate principal stress (or mode of shearing), soil densities, and confining pressures, and the associated drastic effect of different principal stress orientations in reference to the material axes of anisotropy can be well captured. 相似文献
2.
从发挥面的角度出发,分析论证各向异性是引起岩土材料出现非共轴现象的根本原因,得到与材料力学一致的结论。当共轭的两发挥面与沉积面的夹角不相等时,主应力面上将出现塑性应变增量的切向分量,所以塑性应变增量的主方向与应力的主方向非共轴。按照这一结论,对非共轴的数值模拟,也应当根据各向异性本构模型进行。为考虑各向异性影响新近提出的各向异性变换应力法,改变了各应力分量的相对大小,得到的各向异性变换应力张量与真实应力张量的主方向不一致,因此也能反映非共轴。利用各向异性变换应力法,能够在现有的弹塑性本构模型的框架下,描述土的非共轴现象。以各向异性UH模型为例,预测各种加载条件下的非共轴变形,验证了该方法的有效性。 相似文献
3.
采用离散元方法,利用半径扩展法和重力沉积法分别生成具有初始各向同性和各向异性内结构的试样,并开展三轴不排水压缩和拉伸试验,研究不同制样方法产生的初始各向异性对砂土宏微观力学特性及其临界状态的影响。运用组构张量对砂土的各向异性进行量化,分析不同初始组构各向异性对组构张量演化的影响并确定了组构张量的临界值。试验结果表明：初始组构各向异性对试样的剪胀性有重要影响,由于受重力影响形成初始各向异性,其各向异性程度越大、组构方向与加载方向越一致,剪胀性越显著;初始组构各向异性对试样的临界状态没有影响,砂土的组构张量具有唯一的临界状态值。 相似文献
4.
This paper presents a fabric tensor-based bounding surface model accounting for anisotropic behaviour (e.g. the dependency of peak strength on loading direction and non-coaxial deformation) of granular materials. This model is developed based on a well-calibrated isotropic bounding surface model. The yield surface is modified by incorporating the back stress which is proportional to a contact normal-based fabric tensor for characterising fabric anisotropy. The evolution law of the fabric tensor, which is dependent on both rates of the stress ratio and the plastic strain, rules that the material fabric tends to align with the loading direction and evolves towards a unique critical state fabric tensor under monotonic shearing. The incorporation of the evolution law leads to a rotational hardening of the yield surface. The anisotropic critical state is assumed to be independent of the initial values of void ratio and fabric tensor. The critical state fabric tensor has the same intermediate stress ratio (i.e. b value) and principal directions as the critical state stress tensor. A non-associated flow rule in the deviatoric plane is adopted, which is able to predict the non-coaxial flow naturally. The stress–strain relation and fabric evolution of model predictions show a satisfactory agreement with DEM simulation results under monotonic shearing with different loading directions. The model is also validated by comparing with laboratory test results of Leighton Buzzard sand and Toyoura sand under various loading paths. The comparison results demonstrate encouraging applicability of the model for predicting the anisotropic behaviour of granular materials.
相似文献5.
一个考虑土的各向异性的孔压公式及其应用 总被引：2，自引：0，他引：2
为了研究粘土的各向异性对孔压生成的影响,在修正剑桥模型的基础上,采用关口-太田应力比概念、结合邢义川-郑颖人方程,构造了一个各向异性旋转屈服面,建立了一个各向异性弹塑性本构模型;据此推导出一个各向异性孔压表达式,该式可以考虑Lode角以及主应力轴的平面旋转对孔压的影响;并采用新的孔压表达式着重分析了三轴应力状态下Lode角旋转以及主应力轴旋转所造成的孔压发展,并对条形荷载下的平面应变各向异性粘土地基中的孔压发展进行了计算。计算结果表明,地基中由于Lode角旋转造成的孔压不明显,但在荷载边角位置主应力轴旋转造成的孔压不容忽视,尤其是在埋深相对较浅的位置。 相似文献
6.
A simple method called anisotropic transformed stress (ATS) method is proposed to develop failure criteria and constitutive models for anisotropic soils. In this method, stress components in different directions are modified differently in order to reflect the effect of anisotropy. It includes two steps of mapping of stress. First, a modified stress tensor is introduced, which is a symmetric multiplication of stress tensor and fabric tensor. In the modified stress space, anisotropic soils can be treated to be isotropic. Second, a TS tensor is derived from the modified stress tensor for the convenience of developing anisotropic constitutive models to account for the effect of intermediate principal stress. By replacing the ordinary stress tensor with the TS tensor directly, the unified hardening model is extended to model the anisotropic deformation of soils. Anisotropic Lade's criterion is adopted for shear yield and shear failure in the model. The form of the original model formulations remains unchanged, and the model parameters are independent of the loading direction. Good agreement between the experimental results and predictions of the anisotropic unified hardening model is observed. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
7.
针对传统本构理论无法描述土体单剪试验非共轴变形的不足,采用非共轴修正模型进行改进。模型基于材料状态相关临界状态理论,采用宏-细观结合的方法,将1个新的各向异性状态变量引入本构模型来描述砂土的各向异性。考虑细观组构张量和应力张量的几何关系的变化,模型可以描述砂土在主应力轴旋转条件下材料状态的变化,材料状态变化直接导致模型的硬化规律和剪胀性发生变化,因此,模型可以描述该条件下原生向异性对砂土变形的影响。引入非共轴理论对本构模型进行修正,建立了三维非共轴各向异性模型。单剪试验的加载条件会造成主应力轴相对土体沉积面发生旋转,修正模型不但能够描述砂土在主应力轴旋转条件下其原生各向异性对变形的影响,而且可以描述主应力轴旋转造成的应力诱发各向异性对土体变形的影响,因此,该模型能够对整个单剪试验的变形规律进行描述,而且物理意义清晰。通过铝棒堆积体和Toyoura砂单剪试验验证表明,非共轴修正各向异性模型能对单剪试验的整个变形过程进行较好的模拟。 相似文献
8.
Circular opening is commonly encountered in wellbore drilling of petroleum engineering, boring for cast-in situ pile installation, and tunneling excavation. This paper presents a rigorous solution for the elastoplastic responses of the anisotropic soft soil mass around a circular opening excavated under undrained and drained conditions. Both the anisotropic elastoplastic behavior and the 3D strength of the soft clay are incorporated in the present solutions. The well-established anisotropic critical state elastoplastic model S-CLAY1, which can represent the initial fabric anisotropy and stress-induced anisotropy of soft soil, is further modified by the Spatially Mobilized Plane criterion to consider the 3D strength of geomaterials. Then, the investigated problems, excavation of a circular opening under both short-term (undrained) and long-term (drained) conditions, are formulated as a system of first-order differential equations and are solved as initial value problems. The distributions of stress components and anisotropy parameters around the opening, the stress trajectory of a soil particle at the opening wall, as well as the stress–displacement curve at the opening wall are presented to investigate the elastoplastic responses of the opening. Extensive parameters show that the overconsolidated ratio and coefficient of earth pressure at rest (K0) have remarkable effects on the elastoplastic responses around a circular opening.
相似文献9.
This paper presents a micromechanics-based approach to investigate the effects of fabric anisotropy on the behavior of localized failure in granular materials. Based on a micromechanical analysis, the origin of deviatoric stress is decomposed into two components: contact force anisotropy and fabric anisotropy. Using a micro–macro approach, the back stress is interpreted as an contribution to the change of the fabric’s principal direction. The evolution of the back stress is deduced from the stress–fabric relationship and determined with reference to the deviation of the principal directions between the rate of the reduced stress tensor and the actual reduced stress tensor. With this micro–macro framework, a mixed (isotropic–kinematic) hardening model is developed based on the classical isotropic hardening theory. A laboratory simple shear test is first analyzed to validate the proposed model and illustrate the kinematic-hardening mechanism which is usually displayed under non-proportional loading. The analysis further focuses on the anisotropic aspect of localized failure. It has been discovered that the fabric anisotropy can play an important role in the occurrence of shear banding. An increasing degree of fabric anisotropy tends to delay the initiation of the strain localization and result in higher failure strength. The effects of fabric anisotropy have also been illustrated by comparing the theoretical predictions and measured results on the shear band inclination angle, shear strain level and dilatancy at bifurcation. 相似文献
10.
土的基本力学特性及其弹塑性描述 总被引：8，自引：2，他引：6
Cam-clay模型是在等向加载试验基础上建立起来的且能够描述正常固结土在常规三轴试验条件下应力-应变关系的最简单弹塑性模型,是建立各种土的弹塑性本构模型的基础。文中分别按加载方式的不同和土组构的不同,对描述与应力状态、应力历史、应力路径、持荷时间等因素有关的加载方式下土应力应变特性的弹塑性本构模型进行了归纳。对反映不同组构所形成的结构性、各向异性和颗粒破碎等特性的弹塑性本构模型进行了综述,并着重介绍了描述应力状态的三维化方法、反映应力历史影响的超固结土模型和模拟渐近状态路径的渐近状态模型等典型研究成果。 相似文献
11.
Alexandros L. Petalas Yannis F. Dafalias Achilleas G. Papadimitriou 《国际地质力学数值与分析法杂志》2019,43(1):97-123
SANISAND is the name of a family of bounding surface plasticity constitutive models for sand within the framework of critical state theory, which have been able to realistically simulate the sand behavior under conventional monotonic and cyclic loading paths. In order to incorporate the important role of evolving fabric anisotropy, one such model was modified within the framework of the new anisotropic critical state theory and named SANISAND-F model. Yet the response under continuous stress principal axes rotation requires further modification to account for the effect of ensuing noncoaxiality on the dilatancy and plastic modulus. This modification is simpler than what is often proposed in the literature, since it does not incorporate an additional plastic loading mechanism and/or multiple dilatancy and plastic modulus expressions. The new model named SANISAND-FN is presented herein and is validated against published data for loading that includes drained stress principal axes rotation on Toyoura sand. 相似文献
12.
Alexandros I. Theocharis Emmanouil Vairaktaris Yannis F. Dafalias Achilleas G. Papadimitriou 《国际地质力学数值与分析法杂志》2019,43(12):2041-2055
According to classical critical state theory (CST) of granular mechanics, two analytical conditions on the ratio of stress invariants and the void ratio are postulated to be necessary and sufficient for reaching and maintaining critical state (CS). The present work investigates the sufficiency of these two conditions based on the results of a virtual three-dimensional discrete element method experiment, which imposes continuous rotation of the principal axes of stress with fixed stress principal values at CS. Even though the fixity of the stress principal values satisfies the two analytical CST conditions at the initiation of rotation, contraction and abandonment of CS occur, which proves that these conditions may be necessary but are not sufficient to maintain CS. But if fixity of stress and strain rate directions in regard to the sample is considered at CS, the two analytical conditions of CST remain both necessary and sufficient. The recently proposed anisotropic critical state theory (ACST) turned this qualitative requirement of fixity into an analytical condition related to the CS value of a fabric anisotropy variable A defined in terms of an evolving fabric tensor and the plastic strain rate direction, thus, enhancing the two CST conditions by a third. In this way, the three analytical conditions of ACST become both necessary and sufficient for reaching and maintaining CS. In addition, the use of A explains the observed results by relating the stress-strain response, in particular the dilatancy, to the evolution of fabric by means of the relevant equations of ACST. 相似文献
13.
A matrix relating stress and elastic strain tensors for anisotropic particulate materials has been derived. The magnitude of the matrix depends on the state of the material anisotropy. Anisotropy in granular materials depends on strain because normal and tangential particle contact forces, as well as the spatial distribution of the contacts, vary with stress and strain. However, the rotation tensor and the strain tensor cannot be independent; they must satisfy certain constraints to meet the requirement for macroscopic stress tensor symmetry. These conditions and constraints lead to the derivation of the matrix presented in this article. The principal directions of the stress tensor and strain tensor are generally not coincident, and the values of deformation parameters, Young's modulus and Poisson's ratio, are direction dependent; these two aspects are also discussed in this paper. Whereas this matrix can be used in static numerical analyses for elastic problems, we note that this relationship can also be used as a basis upon which to derive a fully incremental stress–strain relationship for anisotropic granular materials in the plastic state, where the anisotropy is evolving with strain. 相似文献
14.
采用宏细观结合各向异性破坏准则对主应力轴旋转条件下砂土的破坏特性进行分析。该准则是加载应力、组构各向异性程度和应力与组构几何关系3个因素的函数,可描述细观特性对任意应力旋转角度条件下破坏特性的影响。根据空心圆柱扭剪试验的特点推导一般正交坐标系下主应力轴旋转条件下的破坏关系式,考虑应力与砂土细观组构的几何关系,推导的关系式即可分析该条件下破坏特性。材料为各向异性时,主应力轴旋转造成破坏特性发生变化,细观各向异性程度越小变化越小;材料为各向同性时,则不会造成砂土破坏特性的变化。该式表明主应力轴旋转条件下不同破坏特性存在的根本原因是砂土各向异性的存在。采用空心圆柱试验结果进行验证,结果表明建立的关系式能较好描述不同应力加载角度条件下砂土的破坏特性。初步验证了由于砂土各向异性的存在使得主应力轴旋转造成了不同的破坏规律。 相似文献
15.
An elastoplastic model for sands is presented in this paper, which can describe stress–strain behaviour dependent on mean effective stress level and void ratio. The main features of the proposed model are: (a) a new state parameter, which is dependent on the initial void ratio and initial mean stress, is proposed and applied to the yield function in order to predict the plastic deformation for very loose sands; and (b) another new state parameter, which is used to determine the peak strength and describe the critical state behaviour of sands during shearing, is proposed in order to predict simply negative/positive dilatancy and the hardening/softening behaviour of medium or dense sands. In addition, the proposed model can also predict the stress–strain behaviour of sands under three-dimensional stress conditions by using a transformed stress tensor instead of ordinary stress tensor. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
16.
17.
18.
Fabric and its evolution need to be fully considered for effective modeling of the anisotropic behavior of cohesionless granular sand. In this study, a three‐dimensional anisotropic model for granular material is proposed based on the anisotropic critical state theory recently proposed by Li & Dafalias [2012], in which the role of fabric evolution is highlighted. An explicit expression for the yield function is proposed in terms of the invariants and joint invariants of the normalized deviatoric stress ratio tensor and the deviatoric fabric tensor. A void‐based fabric tensor that characterizes the average void size and its orientation of a granular assembly is employed in the model. Upon plastic loading, the material fabric is assumed to evolve continuously with its principal direction tending steadily towards the loading direction. A fabric evolution law is proposed to describe this behavior. With these considerations, a non‐coaxial flow rule is naturally obtained. The model is shown to be capable of characterizing the complex anisotropic behavior of granular materials under monotonic loading conditions and meanwhile retains a relatively simple formulation for numerical implementation. The model predictions of typical behavior of both Toyoura sand and Fraser River sand compare well with experimental data. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
19.
The anisotropy effect is exhibited more prominently in sedimentary depositions, and it relates the soil’s mechanical specifications to the directions of imposed loads. Even though this phenomenon has been comprehensively explored in silica sands, few research has been conducted for studying the anisotropic behavior of marine carbonate sands. To bridge this gap, the present study investigates the anisotropy effect on the mechanical behavior of Bushehr carbonate sand acquired from the north shelf of the Persian Gulf in Iran. Toward this end, some undrained principal stress rotation tests are conducted using a hollow cylinder shear torsional apparatus in such a manner that the direction of the applied principal stresses are fixed along a desired orientation and the total mean stress and intermediate principal stress ratio are kept constant. Furthermore, prior to shearing, the samples are consolidated under three confining pressures and two isotropic and anisotropic states. The results show that dilative behavior is observed in all loading directions after initial contraction; this contradicts the response observed in silica sands. The anisotropy response of soil follows two different trends in the contractive and dilative phases. The relation of soil’s mechanical properties shows a descending trend with the angle of maximum principal stress in the contractive phase; on the other hand, the anisotropy behavior shows a dominant parabola trend in the dilative phase, where the maximum ultimate pore pressure and minimum soil strength occur in the stress direction with an angle of α?=?30°. By increasing the confining pressure in the soil element, the intensity of the anisotropy in some mechanical properties except the soil deformation is reduced. Furthermore, the deviatoric-to-effective mean stress ratio in the phase transformation state from contraction to dilation is independent of the loading direction and consolidation stress state, and it is considered one of the intrinsic properties of sand. 相似文献
20.