共查询到20条相似文献，搜索用时 270 毫秒
1.
通过等压固结静、动三轴试验,研究了渤海湾粉质黏土在循环荷载作用下的动力性质和循环荷载后不排水静力性质。试验结果表明,循环应力幅值比越大,平均轴向应变和轴向应变幅值越大;循环应力幅值比达到0.4时,平均轴向应变和轴向应变幅值随着循环周数增加迅速增大;循环应力幅值比相同,固结应力越大,轴向应变幅值越大,而平均轴向应变越小。在较大的循环应力幅值比下,平均孔压比值和孔压幅值比值随着循环周数的增大会达到稳定;循环应力幅值比越大平均孔压比值和孔压幅值比值均越大;相同循环应力幅值,固结应力越大平均孔压比值越小,而固结应力对孔压幅值比值影响较小。循环荷载的作用会导致循环荷载后不排水剪在q-p’平面上有效应力路径和孔压发展表现出超固结土的性质。 相似文献
2.
典型基坑开挖卸荷路径下软土三轴流变特性研究 总被引：1，自引：0，他引：1
模拟基坑开挖下的卸荷路径,进行了不同卸荷条件下包括围压、卸荷路径和排水的卸荷流变试验。试验结果表明：软土在竖向卸荷试验中的回弹变形可分为瞬时回弹变形和滞后回弹变形;在应力控制式三轴试验中,围压和轴压同时卸荷时的初始变形速率较大;仅卸轴压时回弹滞后效应明显,而围压、轴压同时卸荷时由于土体产生剪切变形引起负孔压,使土体回弹滞后效应不明显;在相同卸荷路径下,排水剪切时由于土体吸水膨胀使得流变特性更明显些,且产生的负孔压最终会消散。根据试验成果,建立Merchant流变模型参数与卸荷条件的线性函数关系,并将函数关系代入Merchant模型,最终得到能考虑围压及卸荷路径影响的软土卸荷流变经验模型。研究结果为软土流变变形模型研究及卸荷后基坑变形研究提供了参考。 相似文献
3.
土体的力学特性往往因应力状态和应力路径而异。为了探讨垂直加载和等剪路径下饱和土的力学特性,制备饱和重塑黄土试样,通过固结不排水（CU）和常剪应力排水剪（CSD）三轴试验,分别测定并绘制其应力-应变曲线、孔隙水压力变化曲线和应力路径曲线。试验结果表明,饱和重塑黄土在2种路径下有明显不同的变形特点:CU路径下的应力-应变曲线皆呈弱软化型,孔隙水压力先快速上升后逐渐趋于稳定;CSD路径下维持偏应力为一常量,施加孔隙水压力后的很长时间内试样变形很小,当孔隙水压力增大至试验围压的60%~75%时,试样迅速破坏。CSD路径无偏应力峰值,文中根据轴应变随平均有效应力变化曲线定义了等效峰值破坏线。通过对比发现,2种路径下饱和重塑黄土的有效峰值强度指标差异明显,而有效残余强度指标相近,表明有效残余强度指标是重塑黄土内在属性,受应力路径的影响不大。该研究结果可为实际工程选取正确的应力路径试验提供参考。 相似文献
4.
重塑超固结上海软土力学特性及弹塑性模拟 总被引：1，自引：0，他引：1
对典型上海软土重塑样进行了围压不变和平均主应力不变的三轴排水剪切试验,得到重塑上海软土在不同初始超固结比和围压条件下的应力-应变关系,弄清了超固结比、围压以及应力路径对重塑上海软土的变形和强度特性的影响;根据土体的应力-应变曲线得到重塑上海软土的临界状态应力比及内摩擦角。采用姚仰平等建议的基于伏斯列夫面的超固结土本构模型,并根据等向压缩及三轴排水剪切试验确定其模型参数,对保持围压和平均主应力不变的三轴压缩试验进行了模型预测。预测结果表明,此超固结土本构模型能较好地反映重塑超固结上海软土的变形和强度特性。 相似文献
5.
主应力轴方向旋转变化是地基在波浪、车辆等荷载作用下经受的一种复杂而典型动力路径特征,为研究粉土在不同主应力轴方向变换条件下的强度特性差异,以初始密实度为70％的长江入海口饱和粉土空心试样为对象开展主应力轴旋转、拉压交变动三轴和双幅扭剪三轴试验。试验发现,等压固结条件下3种路径均使试样出现小应变崩塌液化破坏,且崩塌应力状态,可在p’-q空间中用近似平行的一组准不稳定相态线归一。而在液化和崩塌振次上,以同剪应力峰值的动扭剪下最高,动三轴次之,主应力轴旋转最低。在此基础上,提出采用崩塌损耗能对不同路径下土体动强度进行评价,结果表明,崩塌损耗能与剪应力幅值无显著关系,而在上述3种动力路径中,试样崩塌损耗能依次降低,这与3种路径下得到崩塌时刻递增的有效围压特征相匹配。崩塌能强度标准的采用,克服了复杂动力路径下由于剪应力恒定或循环变化造成应力水平无法统一而干扰强度评价的不足 相似文献
6.
围压循环变化将引起土体孔压累积,加剧土体累积塑性应变,导致地基灾变事故。为研究围压循环变化对饱和粉质黏土变形特性的影响,利用GDS双向振动三轴仪,进行部分排水时饱和粉质黏土的变围压循环三轴试验,研究不同应力路径斜率和循环动应力比时饱和粉质黏土的孔压、轴向累积塑性应变和体应变发展规律,建立部分排水条件时考虑循环围压和循环动应力耦合作用的地基粉质黏土累积应变数学模型。试验结果表明：部分排水时饱和粉质黏土孔压、轴向累积塑性应变和体应变均随循环动应力比和应力路径斜率的增大而增大;动孔压比随着振动次数的增加明显分为急剧增加、快速下降和持续平稳3个阶段;轴向累积塑性应变和体应变均随振动次数的增加而增大。当加载次数超过2 500次时,粉质黏土孔压趋于平稳,变形速率略有降低,但变形持续增加。补充试验结果表明,所建立模型与试验结果具有较高的一致性。研究结果将为交通循环荷载导致的地基灾变控制技术提供理论依据。 相似文献
7.
南京砂强度特征与静态液化现象分析 总被引：2，自引：1，他引：1
在松散、中密和密实状态下,以南京粉细砂三轴固结不排水试验结果为基础,进行了强度、变形与静态液化特征的分析。松散南京砂强度特性表现出典型的应变软化,当轴向变形小于1 %时强度达到最大值,而后急剧降低;在50,100 kPa围压时发生了静态液化。但随着固结压力的增大,静态液化消失。与南京砂具有相同土骨架的松散纯净砂却在低围压下未出现静态液化,其形成机制是：粉粒的存在未使土体孔隙比发生较大变化,却引起更大的体缩性;中密和密实南京粉细砂表现出加工硬化的强度特征,临界应力状态线倾角高达55°,具有较高的抗静态液化能力。 相似文献
8.
A database with about 60 undrained monotonic and cyclic triaxial tests on kaolin is presented. In the monotonic tests, the influences of consolidation pressure, overconsolidation ratio, displacement rate and sample cutting direction have been studied. In the cyclic tests, the stress amplitude, the initial stress ratio and the control (stress vs. strain cycles) have been additionally varied. Isotropic consolidation leads to a failure due to large strain amplitudes with eight-shaped effective stress paths in the final phase of the cyclic tests, while a failure due to an excessive accumulation of axial strain and lens-shaped effective stress paths was observed in the case of anisotropic consolidation with \(q^{\text{ ampl }}< |q^{\text{ av }}|\). The rate of pore pressure accumulation grew with increasing amplitude and void ratio (i.e. decreasing consolidation pressure and overconsolidation ratio). The “cyclic flow rule” well known for sand has been confirmed also for kaolin: With increasing value of the average stress ratio \(|\eta ^{\text{ av }}| = |q^{\text{ av }}|/p^{\text{ av }}, \) the accumulation of deviatoric strain becomes predominant over the accumulation of pore water pressure. The tests on the samples cut out either horizontally or vertically revealed a significant effect of anisotropy. In the cyclic tests, the two kinds of samples exhibited an opposite inclination of the effective stress path. Furthermore, the horizontal samples showed a higher stiffness and could sustain a much larger number of cycles to failure. All data of the present study are available from the homepage of the first author. They may serve for the examination, calibration or improvement in constitutive models dedicated to cohesive soils under cyclic loading, or for the development of new models. 相似文献
9.
循环围压对饱和软黏土永久变形的影响 总被引：1，自引：0，他引：1
通过对温州典型饱和软黏土进行一系列不同应力路径下的部分排水循环动三轴试验,研究了部分排水条件下循环围压对饱和软黏土变形特性的影响。试验结果表明：部分排水条件下,与常规的围压保持恒定,偏应力单独循环作用下的三轴试验结果相比,循环围压的存在对饱和软黏土的永久体应变和永久轴向应变均产生了的显著的影响。在相同循环应力比和循环次数下,试样的永久体应变和永久轴向应变均随着循环围压幅值的增大而增大,说明常规的恒定围压循环三轴试验会低估高速交通荷载作用下路基土体的沉降。基于试样第10 000圈的永久体应变和永久轴向应变,分别建立了可以量化部分排水条件下循环围压对饱和软黏土永久体应变和永久轴向应变影响的经验公式,并用于预测饱和软黏土在交通荷载这种包含循环偏应力和循环围压耦合作用的复杂应力条件下产生的永久变形。 相似文献
10.
Damage and Permeability Development in Coal During Unloading 总被引：1，自引：1，他引：0
Hai-Dong Chen Cheng Yuan-Ping Hong-Xing Zhou Wei Li 《Rock Mechanics and Rock Engineering》2013,46(6):1377-1390
One of the key issues in protective seam mining is the pressure relief and permeability improvement effect. In this paper, the results of X-ray CT scanning experiments and permeability experiments using reconstituted coal specimens subjected to the same stress path and the same effective confining pressure (confining pressure minus pore pressure) are combined using the stress–strain relationship to study the damage to reconstituted coal specimens and its influence on permeability during the unloading process. When the effective confining pressure (σ 3 ? p) is unloaded from 8 to 6 MPa and the deviatoric stress increases, the damage variables will increase by 0.0351 and 0.084, respectively, compared with the unloading point under the fixed axial displacement with unloading confining pressure (FADUCP) and fixed deviatoric stress with unloading confining pressure (FDSUCP) stress paths. At the same time, the permeability increased by 1.7 and 16.7 %, respectively. Therefore, the damage variable and permeability increased notably little in this process. After the effective confining pressure is unloaded to approximately 5 MPa, together with the decrease in the deviatoric stress, the growth of the damage variable and permeability begins to accelerate. In addition, the relative decrease in the deviatoric stress with appearing damage cracks, and the relative increase in permeability with the same amount of effective confining pressure being unloaded, shows that the damage to specimens under the FDSUCP stress path is larger than that from the FADUCP stress path. 相似文献
11.
Post-Cyclic Undrained Behavior of Compacted Composite Clay Subjected to Various Cyclic Loading Paths
H. R. Tavakoli A. Shafiee M. K. Jafari 《Geotechnical and Geological Engineering》2011,29(6):1085-1097
Using a sequential procedure of undrained cyclic and post cyclic tests, the strength and stiffness degradation characteristics
of compacted composite clays are studied immediately after various cyclic loading paths by triaxial and hollow cylinder tests.
The effects of cyclic loading paths, sand contents, cyclic loading amplitude and confining pressure on the post-cyclic mechanical
behavior of the composite clays are evaluated. The results point out different peculiarities which can be of interest in assessing
the mechanical behavior of the composite clays under post seismic shaking. The results show that effect of cyclic loading
on post cyclic pore water pressure build-up is significant when pore water pressure build-up is considerably lower than the
associated value in monotonic loading. The effect of sand content and cyclic loading path on degradation of stiffness is more
remarkable than shear strength. Test results also reveal that the effect of sand content on the post cyclic pore water pressure
build-up is minor. However, when the aggregate content increases the shear strength increases. 相似文献
12.
为研究高应力水平条件下岩石卸荷扩容特性及其剪胀角变化规律,开展了若干不同初始围压水平的三轴峰前卸围压试验,同时进行了相应围压水平的常规三轴压缩试验。基于试验成果分析了卸荷应力路径对砂岩扩容的影响效应,总结了卸荷应力路径下剪胀角变化规律,进而提出了基于卸荷应力路径的剪胀角函数,并给出了其数值实现方法,最后通过对三轴峰前卸围压试验的数值模拟,验证了所提出的剪涨角函数的可行性与合理性。研究表明：（1）加载路径时,不同围压水平下峰前扩容体积应变值相差不大,而卸荷应力路径时,随着围压水平的增加,峰前扩容体积应变从最小值3.15×10?3增加到最大值9.65×10?3,卸荷路径下的峰前扩容体积应变约为加载路径的1.1～4.0倍;（2）卸荷应力路径下偏应力峰值对应的体积应变基本为0或接近于0,而加载应力路径下偏应力峰值对应的体积应变均为负值;（3）卸荷应力路径条件下峰前扩容体积应变在总扩容体积应变中所占比例显著大于加载路径;（4）两种应力路径下,剪胀角随塑性剪切应变增加均经历了先增加后减小的过程,并且低围压工况下偏应力峰值对应的剪胀角和最大剪胀角均大于高围压工况;（5）与加载路径相比,卸荷路径下的剪胀角更快达到剪胀角最大值,并且其偏应力峰值对应的剪胀角和最大剪胀角更大;（6）基于砂岩三轴卸荷试验成果,采用线性拟合方法得出了以围压和峰后塑性剪切应变增量为自变量的剪胀角函数,基于该函数与应变软化本构模型的砂岩三轴峰前卸围压试验的数值模拟结果与试验结果吻合较好,表明该函数能较好地描述三轴峰前卸围压条件下砂岩的扩容特性。以上结论可为深部地下工程变形预测、稳定性分析与支护设计提供理论基础。 相似文献
13.
软土在不同应力路径下的力学特性分析 总被引：7，自引：0，他引：7
通过固结不排水剪应力路径试验对广州南沙典型软土在不同固结条件的力学特性进行了系统研究。分析了初始固结状态对软黏土应力路径依赖性的影响,比较了不同应力路径下土的应力-应变关系特征和孔隙水压力变化规律,探讨了孔压分布与土体变形特征的关系,认为侧向卸荷会造成剪应力增加、体应力减小,从而使土体产生剪胀趋势。研究结果还表明,不排水条件下的有效应力路径主要与土样初始固结状态有关,因而同一固结状态下的有效应力路径具有唯一性。另外,试验中的剪切控制方式对有效应力路径有明显影响,但对土体抗剪强度的影响可以忽略。 相似文献
14.
利用GDS应力路径三轴试验系统对南阳膨胀土进行3种应力速率下、4种超固结比（OCR）的被动压缩三轴试验及3种超固结比的被动挤伸三轴试验,分析了不同超固结比和应力速率下其应力（孔隙水压力）-应变关系、有效应力路径及变形模量的演化规律,对膨胀土变形模量各向异性特性进行了初步探讨。结果表明,应力速率、超固结比及卸荷路径均对膨胀土力学特性有一定影响。在被动压缩路径和被动挤伸路径下,随着应力速率和超固结比的增加,相同轴向应变时的偏应力值单调增加;不同超固结比和应力速率时膨胀土的孔隙水压力始终为负值,且其降幅总体上随超固结比的增加而增大,但其降幅随应力速率的变化规律与剪切路径有关。在被动压缩路径下,相同应变时不同应力速率下的孔压降幅基本相同;而在被动挤伸路径下,其降幅随应力速率的增加而增大。边坡开挖路径的选择对于边坡变形影响显著,被动挤伸路径下达到设定极限偏应力时的轴向应变明显大于被动压缩路径。膨胀土变形模量E100随着超固结比和应力速率的增加而增加,但各应力速率下变形模量的各向异性特性则随着超固结比的增加而变弱。 相似文献
15.
Stress-path dependent behavior of a weathered clay crust 总被引：1，自引：0，他引：1
Vinod K. Garga Mahbubul A. Khan Sai K. Vanapalli 《Geotechnical and Geological Engineering》2006,24(6):1481-1509
Triaxial compression and oedometer consolidation tests are commonly performed to evaluate the strength and deformation behavior
of soils. However, in the field, the stress paths imposed by various engineering works may deviate from the stress paths conventionally
used in laboratory tests. Moreover, the stress-paths followed by different soil elements under a foundation are different.
To obtain representative soil parameters, the laboratory stress path should be similar to that followed in the field. In this
study, a significant number of stress-path triaxial tests, with stress probes in various directions, have been conducted to
study the stress-path dependent behavior of an overconsolidated weathered crust of Champlain clay in Eastern Ontario. Both
undrained and drained tests have been conducted for samples isotropically consolidated to the in situ vertical stress and anisotropically consolidated to in situ state of stress. The yield locus of the clay crust has been defined. It has been observed that the strength-deformation and
yielding behavior of this weathered clay crust highly depends on the stress-path as well as on the in situ stress history. 相似文献
16.
Influence of pore pressure on plastic deformation and strength of limestone under compressive stress
This study is devoted to experimental investigation of effects of pore pressure on plastic deformation and failure of a water-saturated limestone. The experimental study is composed of three different groups of laboratory tests. The basic mechanical behavior of the rock is first characterized by drained triaxial compression tests on water-saturated samples without pore pressure. The results are compared with those obtained in a previous study from triaxial compression tests on saturated samples with a constant pore pressure. In the second group, water injection tests under a confining pressure of 20 MPa and different values of deviatoric stress are realized to study the effect of pore pressure increase. Finally, undrained triaxial compression tests are carried out for investigating the coupling effect of plastic deformation and pore pressure variation. Based on experimental data, the validity of effective stress concept for plastic yielding and failure strength is discussed.
相似文献17.
为更加全面地掌握土石混填体的变形、力学特性,采用大型三轴剪切仪分别在常规路径、等应力比路径和等p路径下对不同含石量的土石混填体进行了一系列试验研究。试验结果表明,在低围压下土石混填体的应变软化特征并不明显,其黏聚力普遍较低,而内摩擦角则较高,随试样的含石量从25%增加到70%,其内摩擦角和变形模量亦会随之增加。土石混填体在常规路径和等p路径下的应力-应变关系曲线比较相似,其所求得的抗剪强度指标亦比较接近;而等应力比路径下的应力-应变关系曲线的形态和发展过程均与之存在明显差别。土石混填体在常规路径下具有低压剪胀和高压剪缩的特性,含石量越高,低压剪胀性越明显,反之,则高压剪缩性更为显著;等应力比路径下试样的体积应变与轴向应变之间近似呈线性关系,其斜率随应力比增加而减小;等p路径下试样则是以剪胀性为主,尤其在平均主应力较低时更为显著。 相似文献
18.
Tests on specimens of reconstituted illitic clay have examined the influence of temperature on the mechanical behaviour of clay soils. The program involved consolidation to effective confining pressures up to 1.5 MPa, heating to 100°C, and tests on normally consolidated and overconsolidated specimens with OCR = 2. The tests included isotropic consolidation, undrained triaxial compression with pore water pressure measurement, drained tests along controlled stress paths to investigate yielding behaviour, and undrained tests which involved heating and measurement of the resulting induced pore water pressures. The large strain strength envelope is independent of temperature. However, peak undrained strengths increase with temperature because smaller pore water pressures are generated during shearing. An important contribution from the study is a series of results for the yielding of illitic clay at three different temperatures. For the first time, there is clear evidence of yield loci decreasing in size with increasing temperature. An associated flow rule can be assumed without serious error. The results contribute to the confirmation of a thermal elastic-plastic soil model developed by the authors from cam clay following the addition of a small number of extra assumptions. Depending on the initial stress state, heating under undrained conditions may produce shear failure. 相似文献
19.
超固结黏土单调和耦合循环的剪切特性研究 总被引：1，自引：0，他引：1
针对超固结黏土空心试样,利用土工静力-动力液压三轴-扭转多功能剪切仪,在均等固结条件下进行了单调扭剪和三轴-扭转耦合循环剪切试验。试验结果表明：不同超固结比黏土的单调扭剪强度也可由正常固结黏土的单调扭剪强度得到,得到了不同超固结比下饱和黏土的强度及模量的退化规律;随着超固结比的增大,相同破坏循环次数的动应力比和临界循环应力比均线性增大;超固结比对耦合循环剪切的孔隙水压力的发展模式影响显著。参考Yasuhara的测量方法,采用荷载停止后继续采集孔压的方法可以更好地反映黏土在耦合循环荷载下产生的真实孔压和孔压的增长情况。提出的综合应变式同时考虑了剪切变化和正向偏差变形的共同效应,适合作为主应力连续旋转的耦合循环剪切试验的破坏标准。 相似文献
20.
围压路径对冻结粉质砂土变形行为及强度的影响研究 总被引：2，自引：2，他引：0
目前关于冻土的室内三轴压缩试验研究多采用恒围压下的轴向加载方法,而实际工程中的受压土体基本处于围压、轴压同时发生变化的情况。以冻结粉质砂土为研究对象,进行了变围压和恒围压下的三轴剪切测试。根据试后试样变形情况,给出了试样面积的统一修正公式,研究结果表明：当含水量较小时,围压路径对应力-应变曲线的初始段和最终段没有显见影响,但在应力-应变曲线中间段,变围压下的应力-应变曲线明显在相应的恒围压曲线之下,且初始围压越小,曲线位置越低。当含水量不低于饱和值时,围压路径和含冰量共同影响着应力-应变曲线的发展趋势,且变围压曲线的最终段基本都在相应的恒围压曲线之上,中间段变化特点与含冰量和初始围压有关。围压路径对强度随围压变化趋势的影响跟含水量大小有关。当含水量较小时,两种围压路径下的强度值比较接近;当含水量不低于饱和值时,恒围压下的强度值低于相应变围压下的强度值。 相似文献