共查询到20条相似文献，搜索用时 31 毫秒
1.
In dynamic geotechnical problems, soils are often subjected to a combination of sustained static and fast cyclic loading. Under such loading conditions, saturated and normally consolidated clays generally experience a build-up of excess pore water pressure along with a degradation of stiffness and strength. If the strength of the soil falls below the static stress demand, a self-driven failure is triggered. In this paper, a constitutive model is presented for the analysis of such problems, based on a general multisurface plasticity framework. The hardening behavior, the initial arrangement of the surfaces, and the nonassociated volumetric flow rule are defined to capture important aspects of cyclic clay behavior. This includes nonlinear hysteretic stress-strain behavior, the effect of anisotropic consolidation, and the generation of excess pore water pressure during undrained cyclic loading along with a degradation of stiffness and strength. The model requires nine independent parameters, which can be derived from standard laboratory tests. A customized experimental program has been performed to validate the model performance. The model predictions show a good agreement with test results from monotonic and cyclic undrained triaxial tests, in particular with respect to the strain-softening response and the number of loading cycles to failure. A procedure for a general stress-space implicit numerical implementation for undrained, total stress-based finite element analyses is presented, including the derivation of the consistent tangent operator. Finally, a simulation of the seismic response of a submarine slope is shown to illustrate a possible application of the presented model. 相似文献
2.
《Geomechanics and Geoengineering》2013,8(4):295-306
Recent developments in studies of soil response to earthquake loadings have made it possible to incorporate the rates of pore water pressure build-up in soils in to nonlinear response analyses of the grounds. Such pore pressure changes help in computing the changes in stress-strain behaviour of soils in the deposit progressively as the earthquake progresses. The rate and magnitude of pore pressure generation in soils during seismic loading will have important effects on the shear strength, stability, and settlement characteristics of a soil mass, even if the soil does not liquefy. The results in terms of pore pressure response in soils from a series of experimental investigations using strain-controlled cyclic triaxial tests on soils samples collected from liquefied sites are presented in this paper. The effect of relative density, amplitude of cyclic shear strain, number of loading cycles, confining pressure and frequency of cyclic loading on the pore pressure build-up are studied. Analytical expressions are proposed using regression analysis to define mean relationships between normalized pore water pressure and normalized cycles for the prediction of pore water pressure build-up in silty sands. Also, the pore water pressure build-up in soils is independent of frequency of loading. 相似文献
3.
循环荷载作用下软黏土刚度软化特征试验研究 总被引：4，自引：1，他引：3
循环荷载作用下,软黏土将发生软化现象,而以往的研究中大多未考虑初始偏应力的影响。通过对萧山正常固结饱和软黏土进行应力控制的循环三轴试验,研究了循环荷载作用下土体的刚度软化情况。通过分析每一次循环过程中割线剪切模量的变化规律,探讨了循环次数、循环应力水平、初始偏应力对刚度软化的影响。结果表明,随着循环次数的增加,土体刚度逐渐减小;循环应力水平的提高,初始偏应力的施加将加快刚度软化。在试验的基础上推导了反映土体刚度软化规律的经验公式,得到了萧山软黏土的破坏刚度比。 相似文献
4.
Simulation of cyclic strength degradation of natural clays via bounding surface model with hybrid flow rule 
下载免费PDF全文
下载免费PDF全文 Strength loss of natural clays subjected to seismic loading is a critical factor contributing to earthquake‐induced ground failure and associated hazards. This work proposes a bounding surface constitutive law to simulate cyclic strength degradation of natural clays resulting from the loss of structure and attendant accumulation of excess pore pressures. The proposed model employs an enhanced plastic flow rule that can simulate accurately the development of pore pressure and explicitly incorporates soil structure effects. The validation of the model with reference to the experimental evidence available for 3 structured clays shows that with a single set of parameters the proposed model can reasonably represent the mechanical behavior of natural clays under various loading conditions (1D compression, monotonic shearing in compression and extension, cyclic loading, and postcyclic shearing). Particularly, its satisfactory performance in terms of quantification of cyclic strength degradation encourages the use of the model in simulating boundary value problems related to the stability of geotechnical facilities under earthquakes. 相似文献
5.
6.
7.
利用从现场取得的原状土样,通过室内动三轴试验对循环荷载作用下的变形、孔压和强度特性进行研究。试验研究主要考虑了周围固结压力、循环剪切应力比、荷载频率和循环次数等因素的影响。研究表明,在循环荷载作用下,孔隙水压力和轴向应变均是一个波动上升的过程。当循环应力比增大时,动孔隙水压力变化幅值显著增加,而残余孔压也较大。同时,孔隙水压力值也随着周围压力的增大而明显增大。当作用荷载频率比较大时,需要更多的循环次数才能达到小频率作用荷载能达到的孔隙水压力值。但是,随着循环荷载作用次数的增加,频率对孔隙水压力的影响有减小的趋势。 相似文献
8.
超固结黏土单调和耦合循环的剪切特性研究 总被引：1，自引：0，他引：1
针对超固结黏土空心试样,利用土工静力-动力液压三轴-扭转多功能剪切仪,在均等固结条件下进行了单调扭剪和三轴-扭转耦合循环剪切试验。试验结果表明：不同超固结比黏土的单调扭剪强度也可由正常固结黏土的单调扭剪强度得到,得到了不同超固结比下饱和黏土的强度及模量的退化规律;随着超固结比的增大,相同破坏循环次数的动应力比和临界循环应力比均线性增大;超固结比对耦合循环剪切的孔隙水压力的发展模式影响显著。参考Yasuhara的测量方法,采用荷载停止后继续采集孔压的方法可以更好地反映黏土在耦合循环荷载下产生的真实孔压和孔压的增长情况。提出的综合应变式同时考虑了剪切变化和正向偏差变形的共同效应,适合作为主应力连续旋转的耦合循环剪切试验的破坏标准。 相似文献
9.
土体的力学特性往往因应力状态和应力路径而异。为了探讨垂直加载和等剪路径下饱和土的力学特性,制备饱和重塑黄土试样,通过固结不排水（CU）和常剪应力排水剪（CSD）三轴试验,分别测定并绘制其应力-应变曲线、孔隙水压力变化曲线和应力路径曲线。试验结果表明,饱和重塑黄土在2种路径下有明显不同的变形特点:CU路径下的应力-应变曲线皆呈弱软化型,孔隙水压力先快速上升后逐渐趋于稳定;CSD路径下维持偏应力为一常量,施加孔隙水压力后的很长时间内试样变形很小,当孔隙水压力增大至试验围压的60%~75%时,试样迅速破坏。CSD路径无偏应力峰值,文中根据轴应变随平均有效应力变化曲线定义了等效峰值破坏线。通过对比发现,2种路径下饱和重塑黄土的有效峰值强度指标差异明显,而有效残余强度指标相近,表明有效残余强度指标是重塑黄土内在属性,受应力路径的影响不大。该研究结果可为实际工程选取正确的应力路径试验提供参考。 相似文献
10.
原状和重塑海洋粘土经历动载后的静强度衰减 总被引：5，自引：0，他引：5
根据海洋粉质粘土原状和重塑土样的动三轴试验结果, 比较和分析了两种土样应力、应变、孔隙水压力和不排水抗剪强度行为, 得到了土样的静不排水抗剪强度衰减与波浪荷载作用下土样产生的动应变以及平均累积孔压之间的关系。 并将波浪荷载作用使土样内孔压升高, 有效应力降低, 形成拟超固结现象的理论, 应用到土样不排水抗剪强度衰减与平均累积孔压之间关系的分析;同时与重塑土样的超固结静态剪切试验结果进行比较, 得到了土样在波浪荷载作用后的归一化不排水抗剪强度与拟超固结比之间的关系式。 建议以少量原状土样, 配合大量重塑土样的动三轴试验结果, 实现对实际海洋粘土地基在波浪荷载作用后的静不排水抗剪强度衰化规律的评估。 相似文献
11.
采用大型动三轴试验仪进行重塑高岭土试样的循环三轴试验,试样直径为300 mm,高度为600 mm。圆柱体试样中心放置了一块竖向排水板,在循环加载试验进行时和结束后都可进行径向排水。试验结果验证了径向排水可以有效地消散循环荷载引起的孔隙水压力。通过结合径向固结理论与不排水循环加载土体模型,提出了一个循环荷载作用下径向固结模型,用来描述在允许径向排水的情况下软黏土在循环荷载作用下的孔压累积特性。模型中考虑了应力历史和孔隙水压力消散对孔隙水压力生成的影响,并用大型循环三轴试验结果进行验证。研究发现,当施加较大循环荷载时,径向排水减缓了孔隙水压力累积到临界值的速率,因而土体在破坏前可以经历更多次的循环荷载;当施加中等循环荷载时,径向排水可有效阻止孔隙水压力增长至临界值。除此之外,还研究了加载间歇期对孔压累积特性的影响,结果显示3组循环加载结束后,累积孔隙水压力开始减小,表明之后更多的循环加载并不会引起孔隙水压力的累积增长。 相似文献
13.
在3种不同围压下进行了一系列重塑粉质黏土的静三轴和动-静三轴不排水剪切试验,得到了不同动应力水平条件下粉质黏土的孔压、动应变和不排水剪切强度值。通过对土样的不排水强度、孔压和动应变的无量纲化处理,确定了周期荷载作用后粉质黏土的不排水强度比与动载引起的孔压比和动应变比之间的相关关系。试验结果表明：粉质黏土在周期荷载作用后的不排水强度衰减程度取决于动载引起的动应变比值和孔压比值。当周期荷载引起的动应变比值小于0.1时,孔压比增长较快,土样的不排水强度几乎没有衰减;当动应变比大于0.1时,孔压比增长变慢,土样的不排水强度明显衰减;当动应变比值接近1时,孔压比值达到0.9,土样的不排水强度衰减程度约达到55 % 相似文献
14.
不排水循环荷载作用过程中累积孔压对细砂弹性剪切模量Gmax的影响 总被引：1，自引：1，他引：0
在土工结构物地震有效应力分析中,往往采用Hardin经验公式计算动荷作用过程中由于孔压变化对砂土初始弹性剪切模量Gmax的影响,但由于以往试验手段的限制,这种方法的有效性至今没有得到验证。为此,采用多功能三轴仪和压电陶瓷弯曲元剪切波速测试系统,研究了不排水循环荷载过程中孔压对细砂Gmax的影响。试验结果表明,细砂Gmax可由 Hardin型经验公式计算,但材料参数应通过试验确定;不排水循环荷载作用过程中,细砂Gmax随孔压上升而降低,其值可由其实际平均有效应力和固结后的孔隙比通过由试验得到的Hardin型经验公式计算。 相似文献
15.
In practical engineering, cyclic shear stresses induced by earthquakes, traffic, and waves are superimposed on the initial static shear stress in sand fills or deposits, leading to complex responses of soils such as their deformation characteristics, pore pressure generation, and susceptibility (or cyclic resistance) to liquefaction. To experimentally investigate the undrained cyclic response of saturated sand, a series of triaxial tests were performed, covering a broad range of initial static and cyclic deviatoric stress levels. The results indicate that different stress conditions lead to two types of cyclic behavior: cyclic mobility and residual deformation accumulation. The compressional static stress is beneficial to the cyclic resistance of the dense sand, whereas the extensional static stress is regarded as detrimental as it tended to reduce the cyclic strength. Moreover, by comparing the available test data obtained from the same sand with varying initial densities and confining pressures, the static shear effect on cyclic resistance was found to be dependent on the state of the sand. Compared to the interpretation made using the limiting pore pressure-based criterion, the conventional failure criterion using a cyclic axial strain of 5% may lead to a substantial overestimation of the cyclic resistance, thus resulting in unsafe assessment and design. Hence, by employing the pore pressure criterion, the pore pressure generated in the cyclic tests was investigated and was found to be significantly influenced by the static shear stress. A pore pressure generation model is proposed to obtain the pore pressure characteristics of sand under various static shear stress conditions. 相似文献
16.
动扭剪试验中砂土液化后流动特性分析 总被引：2，自引：0，他引：2
土体在初始液化后仍然可能承受动荷载作用发生大变形。引入流体力学中的剪应变率和表观黏度的概念,对振动扭剪试验中饱和砂土液化后的流动特性进行了分析。分析中将砂土的状态分为0有效应力状态和非0有效应力状态。结果表明,砂土在0有效应力状态下表现出与静扭剪试验类似的“剪切稀化”非牛顿流体的特征,表观黏度随着剪应变率的增大而减小。加载周数对“剪切稀化”状态下的剪应变率幅值有影响,随着加载周数的增加,剪应变率幅值逐渐增大,而对流动曲线的形状没有影响。在非0有效应力状态下,砂土的表观黏度随应变的增大而增大,随孔压比的减小而增大,且所有的试验得到的表观黏度与孔压比具有一致关系。 相似文献
17.
盾构施工与波浪荷载耦合作用后软土力学特性 总被引：1，自引：1，他引：0
针对波浪循环荷载作用和盾构穿越海堤过程中的施工扰动对下卧软黏土地基的弱化效应问题,研究了盾构施工与波浪荷载耦合作用后海洋软土的强度和刚度变化规律。通过逐步降围压的方式模拟盾构施工过程中的地层损失所引起的应力释放,循环加载3 000次模拟波浪荷载长期作用,开展了波浪和盾构施工耦合作用后的软土空心圆柱扭剪不排水剪切单元体试验。试验结果表明:(1) 在盾构施工与波浪荷载耦合作用下,软黏土的强度和刚度均随围压变大而增强,在同一围压下,二者均随波浪循环次数和土体损失率（δ）的增大而减小。(2) 在相同的波浪循环剪切次数下,软黏土初始切线模量随δ的增加而呈线性递减趋势,而软黏土黏聚力和内摩擦角随δ的增加而呈现非线性减小。波浪和盾构施工耦合作用后软黏土的强度和刚度均呈现不同程度的衰减,二者耦合扰动作用对软黏土的弱化效应在实际工程中应充分重视。此研究对探讨复杂扰动条件下海洋结构性软土力学特性规律,丰富和发展扰动状态下结构性软土的计算理论,以及对海岛基础设施建设具有重要的参考价值。 相似文献
18.
Shear strength and pore-water pressure characteristics of sandy soil mixed with plastic fine 总被引：1，自引：0，他引：1
Recent earthquake case histories have revealed the liquefaction of mixtures of sand and fine particles during earthquakes. Different from earlier studies which placed an emphasis on characterisation of liquefaction in terms of the induced shear stress required to cause liquefaction, this study adopted a strain approach because excess pore-water pressure generation is controlled mainly by the level of induced shear strains. The current study includes the results of a set of laboratory tests carried out on sand specimens with the same relative densities and variation in the plastic fines (kaolinite or bentonite) contents ranging from 0 to either 30 % and consolidated at mean confining pressure of 100, 200 and 300 kPa using static triaxial test apparatus, in order to study the influence of fine content and other parameters on the undrained shear strength and liquefaction potential of clayey sand specimens; also, pore-water pressures in the specimens are discussed. Results of tests show that the peak strength decreases as the fines (kaolinite or bentonite) content increases up to a threshold content of fines (FCth) after which, increases in plastic fine content lead to improve the peak shear strength of specimens, and also the ultimate steady-state strength has been improved due to the increased in plastic fines content. Also, pore pressure build-up in clayey sands is generally slower than that observed in pure sand. 相似文献
19.
研究黏性土中桩土界面的抗剪强度及其参数受超孔隙水压力影响的规律,对工程实践具有重要意义。利用自制的大型恒刚度直剪仪,完成了一系列不同界面粗糙度、不同试样含水率和不同剪切速率试验条件下的直剪试验,分析了在不同试验条件下超孔隙水压力变化规律,进而得到考虑超孔隙水压力的桩土界面抗剪强度及其参数的变化规律。研究结果表明：随着界面粗糙度等级提高,桩土界面超孔隙水压力减小,桩土界面抗剪强度、有效黏聚力和有效摩擦系数增加;随着含水率的增加,桩土界面超孔隙水压力增加,桩土界面抗剪强度降低,含水率对桩土界面抗剪强度的影响主要是改变了桩土界面的黏聚力,黏聚力先增大后减小,对摩擦系数的影响较小;特定试验条件下,随着剪切速率的增加,桩土界面超孔隙水压力增加,桩土界面抗剪强度降低,桩土界面黏聚力先增大后又减小,变化幅度不超过2 kPa,对摩擦系数的影响较小。因此,桩土界面抗剪强度及其参数是界面粗糙度、试样含水率和剪切速率变化引起超孔隙水压力变化共同影响的结果,试验结果可供相关工程设计参考。 相似文献
20.
考虑循环载荷下饱和黏土软化的损伤边界面模型研究 总被引：1，自引：0，他引：1
研究表明,循环载荷作用下饱和黏土将发生软化,其机制主要有两个：一是孔压的积累;二是土体原有结构的不断损伤和新结构的不断重塑。针对上述机制,基于广义各向同性硬化准则建立了考虑饱和黏土循环软化的损伤单面模型。该模型在有效应力空间中引入损伤变量,表征土体结构的损伤和重塑程度,在连续的循环加载下,损伤不断累积,边界面则随着损伤的累积不断收缩,以模拟饱和黏土刚度和强度的软化;以应力反向点作为边界面的广义各向同性硬化中心和映射法则的映射中心,灵活地选择塑性模量的插值公式以模拟塑性变形和孔压的累积以及应力-应变的滞回特性。应用该模型对不排水循环三轴试验进行模拟,并且考查了循环周次、循环应力水平和固结历史对饱和黏土循环软化特性的影响,并与相关试验比较,验证了模型的有效性。 相似文献