共查询到20条相似文献，搜索用时 31 毫秒
1.
In this work, 3D discrete element method modeling of drained shearing tests with gap-graded soils after internal erosion is carried out based on published experimental results. The erosion in the model is achieved by randomly deleting fine particles, mimicking the salt dissolving process in the experiments. The present model successfully simulates the stress–strain behavior of the physical test by employing the roll resistance and lateral membrane. The case without erosion shows a strain-softening and dilative response, while strain-hardening and contractive response starts to occur as the degree of erosion increases. The dilative to contractive transition is mainly caused by the increase in void ratio due to the loss of fine particles. The change from dilative behavior to contractive behavior is more abrupt for the specimen with larger fine particle percentage because the soil skeleton is mainly controlled by the fine particles instead of by the coarse soil particles. The transition from “fines in sand” to “sand in fines” might be associated with the rapid increasing in the contacts associated with fine particles in the specimen as the percentage of fine content increases. The erosion scenario based on the hydraulic gradient is also modeled by deleting the fine particles based on the ranking of the contact force. Compared with the scenario based on random deletion, the remaining fine particles for the erosion scenario based on the ranking of contact force are more dispersedly distributed, which might benefit the small strain stiffness but result in a smaller strength. This work provides some insights for better understanding the mechanism behind the internal erosion and the associated stress–strain behavior of soil. The gradient of the critical state line increases with more loss of fine particles denoting that the fine particles are helpful for holding the structure of the soils from larger deformation. 相似文献
3.
Internal instability is a phenomenon of fine particle redistribution in granular materials under the seepage action and consequent change in the soil’s internal structure and hydraulic and mechanical properties. It is one of the primary causes of failures of sand-gravel foundations and embankment dams. The criteria establishment is considered the key to solving the erosion problems, so the existing internal stability criteria need a review and classification to study the recent development trends in soil seepage and erosion. Therefore, this paper aims at reviewing the internal stability factors of gap-graded soil with a focus on the internal erosion mechanism and internal stability evaluation based on geometric and hydraulic criteria. Firstly, the paper compared the effect of several commonly used geometric criteria for gap-graded soil evaluation, such as particle size, fine content, void ratio, and fractal dimension. Furthermore, it provided a hydraulic criteria overview and analyzed the effects of the hydraulic gradient, hydraulic shear stress, confining pressure, and pore velocity on internal erosion. The geometric–hydraulic coupling methods were introduced, with a detailed elaboration of the erosion resistance index method based on accumulated dissipated energy. The capabilities and limitations of these criteria were discussed throughout the paper. It was found that combined Kezdi’s criterion and Kenney and Lau’s criterion is more reliable to evaluate internal stability of soil. The gap-graded soil with fine particle content higher than 35% is not necessarily internally stable. Finally, the energy-based method (erosion resistance index method) can effectively reproduce the total amount of erosion mass and the final spatial distribution of fine particles and identifies erosion. The review's outcome can be used as a basis to evaluate the internal erosion risk for gap-graded soils. The evaluation methods discussed here can help identify the zones of relatively high erosion potential. 相似文献
4.
粗粒土作为无黏性散粒状材料具有状态依赖特性,土体的剪切特性受密度和应力水平影响。易破碎是粗粒土的另一个特点,颗粒破碎影响粗粒土的剪胀、内摩擦角、峰值强度和渗透系数。为了能够准确地描述粗粒土的应力-应变关系,采用初始状态参量描述粗粒土的内部状态,根据三轴试验数据建立考虑颗粒破碎耗能的应力-应变关系,采用相关联流动法则推导考虑颗粒破碎的粗粒土剪胀性“统一本构模型”,并建立初始状态参量与模型参数之间的关系。所建立的统一本构模型既考虑了颗粒破碎对剪胀、内摩擦角的影响,又考虑了剪切特性对土体初始状态的依赖。采用变异粒子群算法拟合试验曲线,确定模型参数。模型计算结果能够很好地拟合试验曲线。采用同一组参数对假定的初始状态进行模拟计算,计算结果表明,模型能够模拟不同初始密度和应力水平下粗粒土变形的一般规律。 相似文献
5.
土体的渗透稳定性是指在渗流条件下宽级配土体内粗颗粒阻止细颗粒流失的能力,土体的渗透稳定性受几何条件、水力条件和物理条件的影响。从几何条件出发,通过对收集的167种土的室内渗透侵蚀试验结果的分析,基于对土体渗透稳定性控制变量地研究,将土分成良好级配土和间断级配土两大类;基于细粒（小于0.063 mm）含量的不同,将每类土又细分为3类,针对不同细类土提出了不同的渗透稳定性几何判定准则。从水力条件出发,研究了应力状态对土体渗透侵蚀起动及破坏水力梯度的影响。试验结果表明,起动水力梯度和破坏水力梯度都随着围压的增大而增大,是由于增大围压使得颗粒间的摩擦力增大的结果。 相似文献
6.
分数阶微分理论在土体静力黏弹性本构模型中得到了广泛应用,然而,其在动力弹塑性模型中的应用尚不多见。为此,基于分数阶微积分理论分析了粗粒料在循环荷载下的变形特性,提出了粗粒料在循环荷载下的分数阶应变率;并以此为基础,进一步建立了粗粒料受静动力荷载作用下的边界面塑性力学本构模型。所提出模型包含10个参数,均可以运用常规三轴试验获得。为了验证所提出模型,选取了几种已有不同文献中的不同粗粒料试验数据进行了模拟,发现,所提出的模型可以较好地模拟粗粒料在静动力加载下的应力-应变行为,对于循环荷载下的长期变形也能较好地预测。 相似文献
7.
Oil or gas production from unconsolidated reservoirs could be hampered by sand migration near the wellbore. This paper presents a numerical investigation of production-induced migration of fine sands towards a wellbore drilled in a gap-graded sediment. The solid–fluid interaction is simulated by coupling the discrete element method and the dynamic fluid mesh. With the merit of DEM and a dynamic mesh, the model is capable of naturally capturing particle movements and spatiotemporal variations of hydraulic properties of the sediment at the pore scale. The results show that fine particles are mobilized by radial flow under an imposed hydraulic gradient, and the increase in the hydraulic gradient causes an increase in the fines production. The microscopic pattern of sand migration is clearly visualized through the simulation. The presence of fine particles affects the process of fines migration through two competing mechanisms. Under a low fine content, fine sands mainly serve as the fines production source, and thus, fines production is enhanced as the fine content increases up to a critical value, beyond which fines production is weakened with a further increase in the fine content since the blocking effect gradually dominates. A barrier layer is likely formed during sand migration due to settling and jamming of fine sands at the throats of pores, as fine sands migrate with the radial flow towards the wellbore. This layer is helpful to slow down sand migration, while it could impede production due to reduced permeability in the affected reservoir. 相似文献
8.
The flow direction is generally different from the gravity direction in geotechnical structures or slopes, the effect of which during suffusion remains unclear. This paper presents a coupled computational fluid dynamics and discrete element method approach to simulate the particle–fluid interaction relevant to this problem. The CFD-DEM approach is first benchmarked by a classic granular system problem, which is then used to investigate the characteristics of suffusion and its impact on the mechanical behavior. Five different angles between gravity and seepage directions for gap-graded soils with two fines contents are examined. Both the macroscopic and microscopic characteristics during suffusion and triaxial loading tests are analyzed. The direction angle is found to play a significant role affecting the erosion process and the mechanical consequence of soils. The results show that the greater the angle is, the harder it is for suffusion to occur and continue. 相似文献
9.
Weathered rockfill materials, characterized by a mixture of soil matrix and rock aggregates, are widely distributed in mountainous areas. These soils are frequently used for subgrade or riprap in engineering practice, and the mobilized shear strength is crucial for analyzing the displacement and stability of these geo-structures. A series of direct shear tests are performed on a gap-graded soil with a full range of coarse fraction. The behavior of gap-graded soils is analyzed, and a simple model is proposed for the evolution of mobilized stress ratio during direct shearing process based on mixture theory. The change of inter-aggregate configuration is incorporated by introducing a structure variable which increases with coarse fraction and decreases approximately linearly with the overall horizontal shear strain in double logarithmic plot. It reasonably reflects a gradually transformation from a matrix-sustained structure into an aggregate-sustained one with the increase of coarse fraction. The model has four parameters, and at least two direct shear tests need to be done for the calibration. Validation of the model is done by using the test data in this work and those from the literature. 相似文献
10.
The effect of grain size distribution on the unconfined compressive strength (UCS) of bio-cemented granular columns is examined. Fine and coarse aggregates were mixed in various percentages to obtain five different grain size distributions. A four-phase percolation strategy was adopted where a bacterial suspension and a cementation solution (urea and calcium chloride) were percolated sequentially. The results show that a gap-graded particle size distribution can improve the UCS of bio-cemented coarser granular materials. A maximum UCS of approximately 575 kPa was achieved with a particle size distribution containing 75% coarse aggregate and 25% fine aggregate. Furthermore, the minimum UCS obtained has applications where mitigation of excessive bulging of stone/sand columns, and possible slumping that might occur during their installation, is needed. The finding also implies that the amount of biochemical treatments can be reduced by adding fine aggregate to coarse aggregate resulting in effective bio-cementation within the pore matrix of the coarse aggregate column as it could substantially reduce the cost associated with bio-cementation process. Scanning electron microscopy results confirm that adding fine aggregate to coarse aggregate provides more bridging contacts (connected by calcium carbonate precipitation) between coarse aggregate particles, and hence, the maximum UCS achieved was not necessarily associated with the maximum calcium carbonate precipitation. 相似文献
11.
Suffusion involves fine particles migration within the matrix of coarse fraction under seepage flow, which usually occurs in the gap-graded material of dams and levees. Key factors controlling the soil erodibility include confining pressure ( p′) and fines content ( Fc), of which the coupling effect on suffusion still remains contradictory, as concluded from different studies considering narrow scope of these factors. For this reason, a systematical numerical simulation that considers a relative wide range of p′ and Fc was performed with the coupled discrete element method and computational fluid dynamics approach. Two distinct macroresponses of soil suffusion to p′ were revealed, ie, for a given hydraulic gradient i = 2, an increase in p′ intensifies the suffusion of soil with fines overfilling the voids (eg, Fc = 35%), but have negligible effects on the suffusion of gap-graded soil containing fines underfilling the voids (eg, Fc = 20%). The micromechanical analyses, including force chain buckling and strain energy release, reveal that when the fines overfilled the voids between coarse particles (eg, Fc = 35%) and participated heavily in load-bearing, the erosion of fines under high i could cause the collapse of the original force transmission structure. The release of higher strain energy within samples under higher p′ accelerated particle movement and intensified suffusion. Conversely, in the case where the fines underfilled the voids between coarse particles (eg, Fc = 20%), the selective erosion of fines had little influence on the force network. High p′ in this case prevented suffusion. 相似文献
12.
颗粒破碎直接改变了粗粒土本身结构,对粗粒土的剪胀、内摩擦角、峰值强度、渗透系数都会产生影响。为了能够准确地描述粗粒土的应力-应变关系,特别是高应力条件下出现显著颗粒破碎时的应力-应变关系,亟待建立考虑颗粒破碎的粗粒土本构模型。根据三轴试验数据,建立考虑颗粒破碎耗能的应力-应变关系,采用相关联流动法则导出考虑颗粒破碎的粗粒土本构模型。所建立的本构模型考虑了颗粒破碎对粗粒土剪胀、内摩擦角的影响。通过变异粒子群优化算法确定模型参数,拟合试验曲线。模型计算结果与试验曲线拟合较好,能够很好地描述粗粒土在不同围压下的体积剪胀、剪缩和应力硬化、软化现象。 相似文献
13.
渗透变形是颗粒材料中细颗粒在渗流作用下发生重分布且导致土体的内部结构、水力及力学特性发生变化的现象,是导致砂砾石土地基及堤防结构破坏的主要原因之一。利用自主研发的刚性壁渗透仪对不同级配及细颗粒含量的间断级配砂砾石土在恒定水头渗流作用下进行渗透变形全过程试验,监测了渗流过程中的局部水力梯度空间分布以及竖向位移变化,分析了渗透试验结束后土体的颗粒级配空间分布变化。研究结果表明：土粒中细颗粒所处的欠填、满填及过填3种堆积状态决定了粗、细颗粒间不同的接触方式,影响其渗透性。渗透试验结束后细颗粒流失量沿试样高度的空间分布可以划分为3个区域,即顶部流失区、中部均匀区及底部流失区。局部水力梯度的快速下降伴随着竖向位移的突变,意味着渗透变形的开始;渗透变形启动时的局部水力梯度大于全局水力梯度,证实了采用大尺寸试验执行渗透试验的必要性。细颗粒处于过填状态的试样依然会发生渗透变形且导致强烈的沉降变形,值得进一步的研究。 相似文献
14.
粗粒土的颗粒破碎直接改变了土体本身结构,对粗粒土的剪胀和内摩擦角都会产生影响。在土体剪切过程中,体积应力和剪切应力在体积应变和剪切应变上做功,这部分能量在剪切过程中转化为颗粒的弹性储能、颗粒间的摩擦耗能、颗粒剪胀时对外做功和颗粒破碎耗能4部分。准确计算剪切过程中粗粒土破碎耗能的目的是：从能量角度分析颗粒破碎对土体本构关系的影响,为建立考虑颗粒破碎的粗粒土本构关系创造条件。通过分析粗粒土的常规三轴试验数据,计算得到了剪切过程中的粗粒土破碎耗能。计算结果表明,常规三轴试验条件下粗粒土破碎耗能主要受固结应力、土体摩擦系数M等因素的影响。 相似文献
15.
Field tests are widely used for soil characterization in geotechnical applications in spite of implementation difficulties. The light penetrometer is a well-known testing tool for fine soils, but the physical interpretation of the output data in the case of coarse granular materials is far less evident. Indeed, the data are considerably more sensitive in this case to various parameters such as fabric structure, particle shapes or the applied impact energy. In order to achieve a better understanding of the penetration process into a coarse granular material, a numerical study was performed by means of contact dynamics simulations. The penetration of a moving tip in a sample composed of irregular grain shapes was studied and the influence of the driving velocity and input energy on the penetration strength was analyzed. The results show that the latter grows with both the penetration rate and energy, despite the strong fluctuations occur due to a jamming–unjamming process in which the contact network connectivity evolves intermittently in correlation with the penetration strength. This analysis suggests that the time-averaged data provided by a penetrometer is reliable information from which the bulk strength properties of coarse granular materials can be evaluated. 相似文献
16.
Experimental evidence shows that a gap-graded soil or a widely-graded granular material may have a bimodal soil–water characteristic curve (SWCC) and a bimodal permeability function. A bimodal SWCC or a bimodal permeability function originates from a dual-porosity structure. To date, the prediction of bimodal SWCCs for gap-graded soils is still a difficult task. In this paper, a bimodal SWCC model is proposed to describe the drying process of granular soils considering a dual-porosity structure. The new SWCC model shows powerful capability in fitting the SWCCs for soils varying from gravel to silt. Regression analysis is conducted to establish empirical relations between the model parameters and the indexes of soil grain-size distribution (GSD). Based on these relations, the new model predicts well both the bimodal SWCCs for gap-graded soils and the unimodal SWCCs for well-graded soils and uniform soils. A bimodal permeability function is also proposed and linked to the new SWCC model. In the absence of experimental SWCCs and permeability functions, the new model can be used to obtain preliminary SWCCs and permeability functions for granular soils. It should be mentioned that the prediction of the SWCC from the GSD is still empirical and does not address the cyclic wetting/drying process. Measurement of the SWCC should be performed wherever an accurate SWCC is required. 相似文献
17.
针对含细颗粒砂土的反常剪切行为,开展了双轴剪切试验的数值模拟,从宏细观角度分析了其反常剪切行为发生的内在机制。数值模拟结果表明,增加围压能提高含细颗粒砂土的抗剪切液化能力,该反常行为的根本原因在于围压上升使得粗细颗粒更有效地参与了力链传递,增加了颗粒间的接触,增强了土体的密实度。细颗粒在土骨架中的移动对砂土的液化起着至关重要的作用,而粗颗粒仅起次要作用。研究表明,细颗粒在剪切过程中会持续从有效土骨架中移出成为无效颗粒,而部分粗颗粒也因失去细颗粒的支撑作用会脱离土骨架,直至试样最终液化。细颗粒一般参与土骨架中的弱力链,而粗颗粒则一般参与强力链,导致细颗粒较粗颗粒更容易在土骨架中移动。 相似文献
18.
揭示煤层气排采储层非饱和流阶段煤粉与气体相互作用机理,对制定排采制度和提高产气量具有重要意义。通过气泡–煤粉微观作用实验装置,系统开展了不同直径大小的气泡对不同粒度和密度煤粉的作用实验,分析了气泡对煤粉运移轨迹和速度的影响及捕获煤粉特征。结果表明,气泡产出能够影响煤粉的运移轨迹,甚至能够捕获煤粉;煤粉通过气泡时会产生3种运动类型：沿着气泡表面运移到气泡底部最后被捕获、沿着气泡表面运移到气泡底部最后脱落及接近气泡时被排斥而轨迹发生偏转。煤粉若被气泡捕捉,则运动速度呈现出减小–增大–减小的变化特征;若未被气泡捕获,速度呈现出减小–增大–减小–增大的变化特征。不同条件下气泡对煤粉的捕获效率高达64.38%～86.64%;在气泡表面最高点附近发生碰撞煤粉被捕获的概率最大,并且随着偏离角度的增大,气泡捕获效率均呈现出逐渐减小的趋势;在相同的碰撞位置下,气泡对煤粉的捕获效率随着煤粉密度、煤粉粒径的增大而减小,随着气泡直径的增大而增大。煤层气产气初期应根据储层的实际导流能力合理控制降压速率,若储层导流能力较强,应加大排采速率,增大气体解吸对煤粉的扰动和捕获作用,促使大量煤粉随地下水或气泡产出;若储层... 相似文献
19.
粗粒土在较大的应力条件下容易产生颗粒破碎现象,而现有的大多数模型都没有考虑剪切过程中的颗粒破碎。模型将塑性功引入土体受力变形过程的能量方程中,推导得到土体流动法则。采用直线型屈服轨迹和非相关联流动法则,利用不排水应力路径计算得到硬化函数,建立了一个考虑颗粒破碎的粗粒土本构模型。对比分析表明：该模型对粗粒土在各种围压下的应力-应变和体应变计算结果与试验曲线吻合较好。 相似文献
20.
The effectiveness of filters to counteract internal erosion in earth structures is particularly related to their ability to capture fine particles moving under seepage flow through the porous material. More precisely, fine particles are likely to be trapped by the narrowest paths between pores: the constrictions. This paper proposes a methodology to compute the constriction size distribution of model granular filters taking into account the relative density of the material. The approach is based upon probabilistic methods which adopt stated simple geometric packing arrangements to represent the solid structure in the extreme density states. Two new models are proposed for the design of the constriction size distribution according to the type of filter grading: continuously graded or gap-graded materials. The models require the usual material characteristics: the grading curve, and the minimum and maximum void ratios for this material. Calibrated on the basis of statistical analyses over numerical assemblies of spheres generated by a discrete element method, the proposed new models constitute a promising tool to significantly improve the modeling of filtration processes in granular materials. 相似文献
|
