共查询到20条相似文献，搜索用时 15 毫秒
1.
An in-situ experimental program in a jointed rock mass was designed and implemented to investigate the rock joint effects on stress wave propagation. Accelerometers were placed on rock surface along three lines at 0, 45 and 90° to the predominant rock joint strike direction. Eight blasts were detonated in a charge hole drilled in the rock mass. The equivalent TNT blast weight ranged from 2.5 to 50.0 kg and the loading density (charge weight divided by the charge chamber volume) varied from 1 to 20.0 kg/m3. A fully coupled detonation with a charge weight of 25.0 kg was also exploded to study the coupling effect. The recorded data are presented and analyzed in this paper. The effects of rock joints on characteristics of stress wave propagation such as peak value attenuation, spectrum, and spatial variations are discussed. 相似文献
2.
Due to the presence of joints, waves are greatly attenuated when propagating across rock masses. Zhu et al. (2011) (Normally incident wave propagation across a joint set with virtual wave source method. J. Appl. Geophys.73, 283–288.) studied normally incident wave propagation across a joint set with the virtual wave source method (VWSM). The introduced VWSM has merits in some aspects, especially the capability of separating differently arriving transmitted waves. However, normal wave incidence is only the special case for wave incidence with arbitrary incident angles. Obliquely incident wave propagation across a joint set is more complicated than normally incident wave propagation due to wave transformation at the joints. As a continuation of the previous paper, this work is extended to analytically study obliquely incident wave propagation across joints with VWSM. Complete theoretical reflection and transmission coefficients across single joint described by displacement discontinuity model are derived through plane wave analysis. The superposition of P wave and S wave is for the first time mathematically expressed and studied. The VWSM is verified through comparison with the propagation matrix method. Through extensive parametric studies on wave transmission across single and multiple parallel joints, it is shown that transmitted wave energy is mainly constrained in the transmitted wave of the same type as the incident wave. And with increasing joint stiffness, the transmission coefficients across single joint increases except those whose wave type is different from the incident wave. The amplitude of superposed transmitted wave for P wave incidence increases with incident angle, which is coincident with field observations. Both joint spacing and number of joints have significant effects on transmission coefficients. We find that when joint spacing is sufficiently large, the transmission coefficient is no longer a constant as the normally incident wave propagation case (Zhu et al., 2011). And when joints are very closely spaced, wave attenuation depends little on the number of joints, which is different from the conclusions from equivalent medium method. 相似文献
3.
为研究地震产生的应力波在断续节理岩体中的传播规律和应力分布趋势,首先,采用数值模拟方法分析应力波通过贯通节理的传播规律,并与已有理论研究结果进行对比,验证数值分析的准确性和适用性;然后,对应力波在断续节理岩体中的传播进行数值模拟,分析透射系数在水平方向的分布趋势以及不同节理连续性对波传播的影响,并结合波的衍射原理,给出定性的理论解释。结果表明:应力波通过断续节理时,节理的透射作用会使应力波振幅减小,引起波的衰减,岩桥的衍射作用则会使波阵面由平面变为曲面,波的传播方向发生改变,从而导致应力波振幅在水平方向的分布发生变化;应力波通过断续节理的透射系数与岩桥尺寸Lr和衍射角μ相关,当衍射角比较小时,透射系数主要受岩桥尺寸Lr的影响,当衍射角较大时,岩桥尺寸Lr和衍射角μ共同影响应力波在岩体中的传播。 相似文献
4.
越来越多的研究表明来自基岩的地震波并不是垂直地面向上传播的。地震波在斜入射与垂直入射时所产生的场地效应有很大不同,由于存在全反射现象,SV波在斜入射时产生的场地效应更为复杂。文章基于均匀弹性半空间地震波传播理论,分别推导得到SV波入射角在小于、大于等于临界角时地震动的计算表达式,通过模型算例研究SV波全反射作用下的地震动特性。研究发现：由SV波产生的地震动主要由入射波和反射波构成,滑行波作用可以忽略;地面运动轨迹具有面波旋转振动特点;随着入射角的增大,地面震动从以水平方向振动为主逐渐过渡到以垂直方向振动为主,两个方向的振动均小于入射波峰值的2倍。 相似文献
5.
A good number of empirical formulae and methods dealing with the analysis of the effects of blast-induced ground vibrations have been developed. The most common approach suggested for estimating the attenuation of particle velocity on the ground is to scale the distance (scaled distance, SD). This approach makes it possible to estimate the peak particle velocity when the amount of explosive charge or the distance or both are altered.Many parameters known to have an influence on particle velocity have been used for particle velocity prediction equations. Some of these parameters are maximum charge per delay, the distance between the station and shot location, burden, inelastic attenuation factor and site factors. However, the impacts of the discontinuities existing on the benches where blasts are detonated on the propagation velocity of seismic waves have not been taken into consideration in these equations.This study aims to examine the impacts of the discontinuity frequency parameter derived through geological measurements carried out on the blasting benches or nearby in a quarry mine (Supren, Eskisehir) in Turkey on the propagation of blast-induced ground vibrations. Developed based on the geological observations carried out on the benches, the model was formed by adding discontinuity frequency parameter to the particle velocity prediction model suggested by Nicholls et al. [Nicholls HR, Johnson CF, Duvall WI. Blasting vibrations and their effects on structures. Bulletin no. 656. Washington, DC: US Bureau of Mines; 1971]. In order to research the effect of the discontinuity frequency in the bench on the blast-induced ground vibrations, the relationship between the recorded peak particle velocity, scaled distance and discontinuity frequency was statistically evaluated for the site. The established relationship and the results of the study are presented. 相似文献
6.
Kemal Hacıefendioğlu Emre Alpaslan 《Stochastic Environmental Research and Risk Assessment (SERRA)》2014,28(2):415-427
This paper presents the dynamic response analysis of industrial masonry chimney subjected to artificially generated surface blast induced ground shock by using a three-dimensional finite element model. The effects of surface blast-induced ground shocks on nearby structures depend on the distance between the explosion centre and the structure, and charge weight. Blast-induced ground motions can be represented by power spectral density function and applied to each support point of the 3D finite element model of the industrial masonry system. In this study, a parametric study is mainly conducted to estimate the effect of the blast-induced ground motions on the nonlinear response of a chimney type masonry structure. Therefore, the analysis was carried out for different values of the charge weights and distances from the charge center. The initial crack and propagation of the crack pattern at the base of the chimney were evaluated. Moreover, the maximum stresses and displacements through the height of the chimney were investigated. The results of the study underline that blast-induced ground motions effects should be considered to perform the non-linear dynamic analysis of masonry type chimney structures more accurately. 相似文献
7.
Grigori Muravskii 《地震工程与结构动力学》2000,29(4):399-418
The paper presents a study of time-harmonic surface waves in a linearly inhomogeneous half-space. The study is based on the solution of that problem for an arbitrary (from 0 to 1/2) value of Poisson's ratio. Vertical vibrations due to a vertical harmonic force, which at large distances from the force represent Rayleigh-type waves, and transverse horizontal vibrations due to a horizontal force, which at large distances form waves of Love's type, are considered in detail. Material damping is taken into consideration. Inhomogeneity significantly affects relationships connecting wave characteristics and the frequency of vibration, and it is shown in the paper how this fact can be used for determining material properties (surface shear modulus, degree of inhomogeneity, damping ratio) with the help of experimental results concerning wave propagation over the surface of the half-space. It is shown that for forced waves the relationship between the wave phase angle and distance can significantly differ from a straight line, i.e. the wave number varies with distance. Therefore, it is desirable to relate experimental and theoretical results to such parts of wave propagation line, which correspond to same phase angle intervals. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
8.
Masayoshi Nakano Kazunari Fujii Shozaburo Takeuchi 《Pure and Applied Geophysics》1988,128(1-2):119-132
Theoretical calculations were performed on reflected and transmitted Rayleigh waves and scattered body waves, in the case where a two-dimensional Rayleigh wave is incident to a wedge-shaped medium having a wedge angle between 250° and 290° and arbitrary value of Poisson ratio. The reflection and transmission coefficients of Rayleigh waves were also experimentally measured in cases of wedges with 190° to 330° wedge angles. The method of theoretical analysis and the techniques of experiment are based on those developed in our preceding research (W-1. W-2 and W-3). Compared with the results where the wedge angle is smaller than 180° (W-1 and W-2), all features show consistent variation with wedge angle. 相似文献
9.
产生地震动空间效应的主要原因是地质构造的变化会极大地改变复杂场地条件下到达不同观测点的地震波,因此地震波振幅和相位发生明显变化。本文利用有限元和边界元耦合的方法,通过建立雷克子波入射时的非线性响应模型求解复杂场地条件下的波动积分方程,进行复杂近地表构造中地震波场数值模拟,旨在分析复杂场地条件下入射方向不同的地震波的动力响应规律。研究结果显示近地表会极大地改变地震波传播特征,导致地震波传播趋向不一致性的因素是由于复杂场地条件重建了地震波的传播路径,尤其须指出的是非一致性地表位移响应源于软土层中低频子波的传播。在地震响应分析中导致系统不同动力响应的其他原因是主频和地震波速度结构的改变,同时地震波入射角度的改变会引起到达观测点的时间滞后,地表位移响应随着入射角度的增大而增加,地震动的空间效应随着入射角度的减小而愈趋明显。 相似文献
10.
《Journal of Applied Geophysics》2010,70(3-4):131-139
We investigated the properties of guided wave propagating in grouted rock bolts and the formation of the interface wave through theoretical analysis along with experimental and numerical simulations. Experimental and numerical simulations reveal that the wave propagating in anchorage structure is related to boundary conditions within the range of excitation wave frequencies. Waves with different frequencies have different propagation velocities and attenuation characteristics. The optimal excitation wave occurs in grouted rock bolts with minimized attenuation and maximized propagation distance, and the end reflection of grouted rock bolts can be observed clearly. Longitudinal wave propagating in rock bolts is very sensitive to anchorage strength. With the increase of anchorage strength, longitudinal wave gradually attenuates and eventually disappears. Subsequently, interface wave appears and the velocity of wave propagating in the grouted part becomes that of the interface wave. Based on these studies, ultrasonic guided wave was used to study the end reflection of embedded rock bolts with different anchorage strengths and bonding lengths. The relationships among anchorage strength, bonding length and attenuation coefficient K, as well as the means to inspect the bonding quality of the embedded rock bolts were also evaluated. 相似文献
11.
This paper focuses on the propagation and dynamic effects of blast waves in faulted rock masses. A coupled method combining UDEC and LS-DYNA is presented whereby the explosion process is simulated by LS-DYNA while the wave propagation and its dynamic effects in rock masses with faults are modeled by UDEC. The blast-induced crack evolution and failure zone distribution in faulted rock masses are explored using the proposed coupled method. The relationship between rock failure and fault parameters such as dip, stiffness and friction are also investigated. The results indicate that the coupled method is feasible and effective for evaluating explosion in discontinuous rock system and the existence of faults exerts significant influence on the pattern of rock masses failure. 相似文献
12.
Average elastic properties of a fluid‐saturated fractured rock are discussed in association with the extremely slow and dispersive Krauklis wave propagation within individual fractures. The presence of the Krauklis wave increases P‐wave velocity dispersion and attenuation with decreasing frequency. Different laws (exponential, power, fractal, and gamma laws) of distribution of the fracture length within the rock show more velocity dispersion and attenuation of the P‐wave for greater fracture density, particularly at low seismic frequencies. The results exhibit a remarkable difference in the P‐wave reflection coefficient for frequency and angular dependency from the fractured layer in comparison with the homogeneous layer. The biggest variation in behaviour of the reflection coefficient versus incident angle is observed at low seismic frequencies. The proposed approach and results of calculations allow an interpretation of abnormal velocity dispersion, high attenuation, and special behaviour of reflection coefficients versus frequency and angle of incidence as the indicators of fractures. 相似文献
13.
The phenomenon of reflection and transmission of plane harmonic waves at the plane interface between two dissimilar poroelastic solids saturated with two immiscible viscous fluids is investigated. Both porous media are considered dissipative due to the presence of viscosity in pore‐fluids. Four attenuated (three dilatational and one shear) waves propagate in such a dissipative porous medium. A finite non‐dimensional parameter is used to define the effective connections between the surface‐pores of two media at their common interface. Another finite parameter represents the gas‐share in the saturation of pores. An attenuated wave in a dissipative medium is described through the specification of directions of propagation and maximum attenuation. A general representation of an attenuated wave is defined through its inhomogeneous propagation, i.e., different directions for propagation and attenuation. Incidence of an inhomogeneous wave is considered at the interface between two dissipative porous solids. This results in four reflected and four transmitted inhomogeneous waves. Expressions are derived for the partition of incident energy among the reflected and transmitted waves. Numerical examples are studied to determine the effects of saturating pore fluid, frequency, surface‐pore connections and wave inhomogeneity on the strengths of reflected and transmitted waves. Interaction energy due to the interference of different (inhomogeneous) waves is calculated in both the dissipative porous media to verify the conservation of incident energy. 相似文献
14.
迭部5.9级地震爆破地震波动力学特性的变化 总被引：4，自引：0，他引：4
本文利用遥测传输台网可见记录和磁带记录对厂坝炮爆破进行地震波动力学特性分析,发现各次爆破记录有一致性。对失真信号进行滤波处理,经凝聚函数分析证明了爆源的一致性。对1987年1月8日迭部Ms=5.9地震的分析,表明由于介质状态的改变,记录到的地震波优势频率向高频方向移动。在近震中有关台站上,地震波位移谱出现多峰与能量分散现象,拐角频率也向高频方向移动,振幅比呈现低—高—发震的形态。在地震前二十几天,主频处地震波衰减小,而震后明显变大。上述特征可能与该地震孕育过程中应力水平和介质状态变化有关。 相似文献
15.
目前在地震勘探频带范围内通常假设品质因子Q与频率无关,且呈衰减各向同性.事实上,相比较速度各向异性,介质的衰减各向异性同样不可忽视.本文将衰减各向异性和速度各向异性二者与常Q模型相结合,建立了黏弹性衰减VTI介质模型,并基于分数阶时间导数理论,给出了对应的本构关系和波动方程.利用均匀平面波分析和Poynting定理,推导出准压缩波qP、准剪切波qSV和纯剪切波SH的复速度、相速度、能量速度以及品质因子的解析表达式.对模型的正确性进行了数值验证,并分析了qP,qSV和SH波在介质中的传播特性.数值试验结果表明:本模型能够实现理想的恒定Q行为,表现了品质因子和速度的各向异性特征,显示出黏弹性增强将导致能量速度和相速度的频散曲线变化剧烈;速度和衰减各向异性参数与传播角度之间的耦合效应对qP,qSV和SH波的速度和能量影响明显;qP,qSV和SH波的频散曲线和波前面随着衰减各向异性强度的改变发生显著变化,其中耦合在一起的qP和qSV波变化趋势相同,而SH波与它们呈现相反的变化规律.本研究为从常Q模型角度分析地震波在衰减各向异性黏弹性介质中的传播特征奠定了理论基础. 相似文献
16.
This paper investigates the effects of random variations of soil properties on site amplification of seismic waves. First, based on attenuation laws and the filtered Tajimi–Kanai spectrum, seismic motion at the base rock of a soil site is stochastically generated according to an assumed earthquake with a given magnitude and epicentral distance. Motions on the surface of this layered random soil site are calculated by nonlinear wave propagation methods, and by assuming the incoming seismic wave consisting of SH wave or combined P and SV waves. Soil properties, including shear modulus, damping ratio and mass density, as well as ground water level are considered as random in the numerical calculation. The Rosenblueth method is used to solve the random dynamic responses of the soil site. Parametric calculations are performed to investigate the effects of various parameters on site amplification of seismic waves. The mean and maximum ground motions on surface of the site are estimated. Numerical results indicate that the estimated surface motions differ substantially if the random variations of soil properties and soil saturation level are taken into consideration in the analysis. 相似文献
17.
应力波作用下节理面前后电磁辐射强度的变化 总被引：2，自引：0，他引：2
从压电体中的压电本构方程出发,得到了含石英等压电介质岩体在应力波作用下产生的电场值的关系表达式．电磁辐射强度随电阻率增大而增大,随传播距离发生衰减．对于电阻率较大导电性能较差的岩石来说,压电电荷的贡献是足够引起重视的．利用所得到的表达式对实际地震电磁信号幅值进行了估算,所得结果与实测结果吻合．依据所得到的电场值的表达式及应力波在节理面处的透射解,获得了垂直入射应力波作用下产生的电磁波在线性变形节理面前后的强度关系．研究了节理参数、岩体电性参数以及入射波频率对节理面前后电磁辐射强度的影响．结果表明,电磁辐射的强度随节理初始刚度增大而增大;对于节理面两侧岩体性质不同的情形,从理论上讲,电磁辐射强度随单个参数的变化是明确的,但在多种参数的综合影响下,电磁辐射强度变化情况相对比较复杂．本文的理论计算结果与其它众多学者得出的实验结果一致． 相似文献
18.
19.
To estimate the amplification characteristics of ground motions in the heavily damaged belt zone in Kobe City during the 1995 Hyogo-ken Nanbu earthquake, 3D wave propagation analyses of a 2D deep irregular underground structure model with a vertical discontinuity were performed at an early stage as a preliminary and qualitative study. The hyperelement method was applied to the analyses for incident plane waves expected from the wavefields due to the source mechanism. The observation records at Kobe University of the rock site were used as control motions. The ground motions on the engineering bedrock (assumed to be on the free surface of the Osaka group layers having a shear velocity of 500 m/s) and at ground surface were calculated. The effects of the deep irregular underground structure and shallow surface layers on the ground motion amplification are discussed. Although there are qualifications due to the uncertain characteristics of the input rock motion and shear wave velocities of the underground structure, the analytical results show that the ground motion in the heavily damaged belt zone were amplified due to the focusing effect of the deep irregular underground structure as well as the shallow surface layers, and that the calculated peak ground acceleration (PGA) distribution coincided closely with the distributions of structural damage. © 1997 by John Wiley & Sons, Ltd. 相似文献