共查询到20条相似文献，搜索用时 15 毫秒
1.
Reflection and transmission of inhomogeneous waves in a composite porous solid saturated by two immiscible fluids 
下载免费PDF全文
下载免费PDF全文 This paper is concerned with reflection and transmission of a plane, elastic, and inhomogeneous wave striking obliquely at some discontinuity inside a porous medium composed of two distinct solids and saturated by two immiscible fluids. It is found that four P‐ and two SV‐waves are reflected, whereas four P‐ and two SV‐waves are transmitted at the interface. All reflected and transmitted waves are inhomogeneous in nature and specified with different directions of propagation and attenuation vectors. An expression for the Umov–Poynting energy flux vector is derived for the system. Continuity of energy flux along normal to the interface gives 12 required boundary conditions. Expressions of amplitude and energy ratios of various reflected and transmitted waves are derived. Variations in amplitude and energy coefficients of reflected and transmitted waves with angle of incidence are numerically studied for a porous matrix composed of shaley sandstone and clay, saturated with water and oil. The effects of change in oil saturation and volume fraction of clay are also observed on amplitude ratios. Numerical simulation reveals that the change in sign in the difference of capillary pressure across the interface causes jump in the values of amplitude ratios of all waves. 相似文献
2.
弹性孔隙介质分界面上的反透射系数特征,在岩性划分、流体识别、储层边界判识等方面有重要的应用.本文研究上层为含两项不混合黏性流体孔隙介质、下层为含单项黏性流体孔隙介质分界面上的反透射理论.首先根据两种孔隙介质分界面上的能量守恒得到边界条件,再将波函数、位移、应力与应变关系代入边界条件,推导出完全连通孔隙情况下,第一类纵波入射到孔隙介质分界面上的反透射系数方程.通过建立砂岩孔隙介质模型,分别分析不同孔隙流体类型、不同含油饱和度及不同入射角情况下,各类波的反透射系数特征.研究表明,第二、三类纵波反透射系数数值比第一类纵波小多个数量级,且两者对入射角的变化不敏感,但对孔隙流体性质、含油饱和度的变化较敏感,而横波反透射系数特征恰好与此相反;第一类纵波反透射系数特征比较复杂,入射角、孔隙流体的性质及含油饱和度的变化都对其产生影响.不同孔隙流体弹性物性的差异、孔隙介质中含油饱和度的变化及不同入射角引起垂向和切向应力分量的变化都会影响各类波的反透射系数特征,分析这些特征可以为研究储层含油气性提供理论基础. 相似文献
3.
M.D. Sharma 《Geophysical Prospecting》2019,67(8):2147-2160
Propagation of harmonic plane waves is studied in a patchy-saturated porous medium. Patchy distribution of the two immiscible fluids is considered in a porous frame with uniform skeletal properties. A composition of two types of patches, connected through continuous paths, constitutes a double-porosity medium. Different compressibilities of pore-fluids in two porous phases facilitate the wave-induced fluid-flow in this composite material. Constitutive relations are considered with frequency-dependent complex elastic coefficients, which define the dissipative behaviour of porous aggregate due to the flow of viscous fluid in connected patches. Relevant equations of motion are solved to explain the propagation of three compressional waves and one shear wave in patchy-saturated porous solids. A numerical example is solved to illustrate dispersion in phase velocity and quality factor of attenuated waves in patchy-saturated porous materials. Role of fluid–solid inertial coupling in Darcy's law is emphasized to keep a check on the dispersion of wave velocities in the porous composite. Effects of patchy saturation on phase velocities and quality factors of attenuation are analysed using the double-porosity formulation as well as the reduced single-porosity equivalents. 相似文献
4.
Reflection and refraction at an imperfectly bonded interface between poroelastic solid and cracked elastic solid 总被引：1，自引：1，他引：0
Porous solid is in contact with a cracked elastic solid at a plane interface between them. For the presence of vertically aligned microcracks, the elastic solid behaves transversely isotropic to wave propagation. The coefficients of elastic anisotropy depend on the crack density and crack porosity in the medium. A loose bonding is considered between the two solids so that a limiting case could be the welded contact. At the plane interface, the imperfection in welded bonding is represented by tangential slipping and, hence, results in the dissipation of a part of strain energy. Three types of waves propagate in an isotropic fluid-saturated porous medium, which are considered for incidence at the interface. Incidence of a wave results in three reflected waves and two refracted waves. Partition of incident energy among the reflected and refracted waves is studied for each incidence, varying from normal to grazing directions. Numerical example calculates the energy shares of reflected and refracted waves at the plane interface between water-saturated sandstone and basalt. These energy shares are computed and analyzed for different values of crack parameters as well as loose bonding parameter. 相似文献
5.
A problem of reflection and transmission of elastic waves at a plane interface between a uniform elastic solid half-space and a porous elastic half-space containing two immiscible fluids is investigated. The theory developed by Lo, Sposito and Majer for porous media containing two immiscible fluids is employed to find out the reflection and transmission coefficients. The incident wave is assumed to propagate through the uniform elastic half-space and two cases are considered. In the first case, a beam of plane longitudinal wave is assumed to be incident and in the second case, a beam of transverse wave is assumed to be incident at the interface. By taking granite as impervious elastic medium and columbia fine sandy loam containing air-water mixture as porous medium, reflection and transmission coefficients are obtained. By neglecting the inertial coupling coefficients, these coefficients are reduced to those obtained by Tomar and Arora using the theory of Tuncay and Corapcioglu. It is found that the inertial coupling parameters significantly affect the phase speeds and the amplitude ratios of the transmitted waves. 相似文献
6.
In fractured reservoirs, seismic wave velocity and amplitude depend on frequency and incidence angle. Frequency dependence is believed to be principally caused by the wave‐induced flow of pore fluid at the mesoscopic scale. In recent years, two particular phenomena, i.e., patchy saturation and flow between fractures and pores, have been identified as significant mechanisms of wave‐induced flow. However, these two phenomena are studied separately. Recently, a unified model has been proposed for a porous rock with a set of aligned fractures, with pores and fractures filled with two different fluids. Existing models treat waves propagating perpendicular to the fractures. In this paper, we extend the model to all propagation angles by assuming that the flow direction is perpendicular to the layering plane and is independent of the loading direction. We first consider the limiting cases through poroelastic Backus averaging, and then we obtain the five complex and frequency‐dependent stiffness values of the equivalent transversely isotropic medium as a function of the frequency. The numerical results show that, when the bulk modulus of the fracture‐filling fluid is relatively large, the dispersion and attenuation of P‐waves are mainly caused by fractures, and the values decrease as angles increase, almost vanishing when the incidence angle is 90° (propagation parallel to the fracture plane). While the bulk modulus of fluid in fractures is much smaller than that of matrix pores, the attenuation due to the “partial saturation” mechanism makes the fluid flow from pores into fractures, which is almost independent of the incidence angle. 相似文献
7.
Wave-induced flow is observed as the dominated factor for P wave propagation at seismic frequencies. This mechanism has a mesoscopic scale nature. The inhomogeneous unsaturated patches are regarded larger than the pore size, but smaller than the wavelength. Surface wave, e.g., Rayleigh wave, which propagates along the free surface, generated by the interfering of body waves is also affected by the mesoscopic loss mechanisms. Recent studies have reported that the effect of the wave-induced flow in wave propagation shows a relaxation behavior. Viscoelastic equivalent relaxation function associated with the wave mode can describe the kinetic nature of the attenuation. In this paper, the equivalent viscoelastic relaxation functions are extended to take into account the free surface for the Rayleigh surface wave propagation in patchy saturated poroelastic media. Numerical results for the frequency-dependent velocity and attenuation and the time-dependent dynamical responses for the equivalent Rayleigh surface wave propagation along an interface between vacuum and patchy saturated porous media are reported in the low-frequency range (0.1–1,000 Hz). The results show that the dispersion and attenuation and kinetic characteristics of the mesoscopic loss effect for the surface wave can be effectively represented in the equivalent viscoelastic media. The simulation of surface wave propagation within mesoscopic patches requires solving Biot’s differential equations in very small grid spaces, involving the conversion of the fast P wave energy diffusion into the Biot slow wave. This procedure requires a very large amount of computer consumption. An efficient equivalent approach for this patchy saturated poroelastic media shows a more convenient way to solve the single phase viscoelastic differential equations. 相似文献
8.
本文定义了各向异性黏弹性参数修正因子,并将其引入到黏弹性模型中以体现泥质含量对黏弹性机制的影响,同时将波传播过程中孔隙介质骨架黏弹性力学机制与两种孔隙流体流动力学机制（Biot流动和喷射流动机制）有机地统一起来处理,从而给出了描述含泥质低孔渗孔隙各向异性介质中波传播规律的黏弹性Biot/squirt (BISQ)模型.数值计算结果表明,入射波的方位角、各向异性渗透率以及泥质含量等对含流体复杂孔隙介质中波频散和衰减的影响具有显著的方位各向异性特征,在低频范围内（地震波勘探频率）黏弹性力学机制对波传播能量的衰减起主导作用. 相似文献
9.
Saturation of porous rocks with a mixture of two fluids has a substantial effect on seismic‐wave propagation. In particular, partial saturation causes significant attenuation and dispersion of the propagating waves due to the mechanism of wave‐induced fluid‐flow. Such flow arises when a passing wave induces different fluid pressures in regions of rock saturated by different fluids. Most models of attenuation and dispersion due to mesoscopic heterogeneities imply that fluid heterogeneities are distributed in a regular way. However, recent experimental studies show that mesoscopic heterogeneities have less idealized distributions and that the distribution itself affects attenuation and dispersion. Based on an approximation for the coherent wavefield in random porous media, we develop a model which assumes a continuous distribution of fluid heterogeneities. As this continuous random media approach assumes that there will be a distribution of different patch sizes, it is expected to be better suited to modelling experimental data. We also show how to relate the random functions to experimentally measurable parameters. 相似文献
10.
An analytical model for describing the propagation and attenuation of Rayleigh waves along the free surface of an elastic porous medium containing two immiscible, viscous, compressible fluids is developed in the present study based on the poroelastic equations formulated by Lo et al. [Lo WC, Sposito G, Majer E. Wave propagation through elastic porous media containing two immiscible fluids. Water Resour Res 2005;41:W02025]. The dispersion equation obtained is complex-valued due to viscous dissipation resulting from the relative motion of the solid to the pore fluids. As an excitation frequency is stipulated, the dispersion equation that is a cubic polynomial is numerically solved to determine the phase speed and attenuation coefficient of Rayleigh waves in Columbia fine sandy loam permeated by an air–water mixture. Our numerical results show that, corresponding to three dilatational waves, there is also the existence of three different modes of Rayleigh wave in an unsaturated porous medium, which are designated as the R1, R2, and R3 waves in descending order of phase speed, respectively. The phase speed of the R1 wave is non-dispersive (frequency-independent) in the frequency range we examined (10 Hz–10 kHz) and decreases as water saturation increases, whose magnitude ranges from 20% to 49% of that of the first dilatational wave with respect to water content. However, it is revealed numerically that the R2 and R3 waves are functions of excitation frequency. Given the same water saturation and excitation frequency, the phase speeds of the R2 and R3 waves are found to be approximately 90% of those of the second and third dilatational waves, respectively. The R1 wave has the lowest attenuation coefficient whereas the R3 wave attenuates highest. 相似文献
11.
Due to the presence of joints, waves are greatly attenuated when propagating across rock masses. Zhu et al. (2011) (Normally incident wave propagation across a joint set with virtual wave source method. J. Appl. Geophys.73, 283–288.) studied normally incident wave propagation across a joint set with the virtual wave source method (VWSM). The introduced VWSM has merits in some aspects, especially the capability of separating differently arriving transmitted waves. However, normal wave incidence is only the special case for wave incidence with arbitrary incident angles. Obliquely incident wave propagation across a joint set is more complicated than normally incident wave propagation due to wave transformation at the joints. As a continuation of the previous paper, this work is extended to analytically study obliquely incident wave propagation across joints with VWSM. Complete theoretical reflection and transmission coefficients across single joint described by displacement discontinuity model are derived through plane wave analysis. The superposition of P wave and S wave is for the first time mathematically expressed and studied. The VWSM is verified through comparison with the propagation matrix method. Through extensive parametric studies on wave transmission across single and multiple parallel joints, it is shown that transmitted wave energy is mainly constrained in the transmitted wave of the same type as the incident wave. And with increasing joint stiffness, the transmission coefficients across single joint increases except those whose wave type is different from the incident wave. The amplitude of superposed transmitted wave for P wave incidence increases with incident angle, which is coincident with field observations. Both joint spacing and number of joints have significant effects on transmission coefficients. We find that when joint spacing is sufficiently large, the transmission coefficient is no longer a constant as the normally incident wave propagation case (Zhu et al., 2011). And when joints are very closely spaced, wave attenuation depends little on the number of joints, which is different from the conclusions from equivalent medium method. 相似文献
12.
模拟弹性波在孔隙介质中传播，需要稳定有效的吸收边界来消除或尽可能的减小由人工边界引起的虚假反射. 本文在前人工作基础上，首次建立了弹性孔隙介质情况下完全匹配层吸收边界的高阶速度-应力交错网格有限差分算法，并详细讨论了完全匹配层的构建及其有限差分算法实现. 首先，本文通过均匀孔隙模型的数值解与解析解的对比，验证所提出的数值方法的正确性；然后，本文考察了完全匹配层对不同入射角度入射波和自由表面上的瑞利波的吸收性能，将完全匹配层与廖氏和阻尼吸收边界进行了对比，研究了这三种吸收边界在不同吸收厚度情况下对弹性波吸收能力. 数值结果表明，在孔隙介质中，完全匹配层作为吸收边界能十分有效地吸收衰减外行波，无论对体波还是面波，是一种高效边界吸收算法. 相似文献
13.
Seismic wave propagation in reservoir rocks is often strongly affected by fractures and micropores. Elastic properties of fractured reservoirs are studied using a fractured porous rock model, in which fractures are considered to be embedded in a homogeneous porous background. The paper presents an equivalent media model for fractured porous rocks. Fractures are described in a stress‐strain relationship in terms of fracture‐induced anisotropy. The equations of poroelasticity are used to describe the background porous matrix and the contents of the fractures are inserted into a matrix. Based on the fractured equivalent‐medium theory and Biot's equations of poroelasticity, two sets of porosity are considered in a constitutive equation. The porous matrix permeability and fracture permeability are analysed by using the continuum media seepage theory in equations of motion. We then design a fractured porous equivalent medium and derive the modified effective constants for low‐frequency elastic constants due to the presence of fractures. The expressions of elastic constants are concise and are directly related to the properties of the main porous matrix, the inserted fractures and the pore fluid. The phase velocity and attenuation of the fractured porous equivalent media are investigated based on this model. Numerical simulations are performed. We show that the fractures and pores strongly influence wave propagation, induce anisotropy and cause poroelastic behaviour in the wavefields. We observe that the presence of fractures gives rise to changes in phase velocity and attenuation, especially for the slow P‐wave in the direction parallel to the fracture plane. 相似文献
14.
地下岩石由岩石骨架和孔隙流体组成,通常流体含黏性.地震波在地下介质中传播时受岩石骨架和黏性流体的影响会呈现出复杂的变化.本文将流、固体位移和应力连续作为边界条件,推导出含黏性流体孔隙介质分界面上反透射系数方程;通过建立上层为饱油、下层为饱盐水的砂岩孔隙介质模型,开展反透射系数特征研究,分别分析不同频率、不同黏滞系数条件下,含黏性流体孔隙介质分界面上反透射系数随入射角的变化.研究表明,孔隙介质分界面上和等效介质分界面上的反透射系数分别随入射角的变化趋势基本一致,说明方程推导和数值计算的正确性;快纵波反透射系数受频率、流体黏性的影响较小,而快横波反透射系数在一定入射角范围内受频率、流体黏性的影响比较大;由于黏性孔隙流体的作用,慢纵波和慢横波的反透射系数受入射角、频率及流体黏性的影响都很大. 相似文献
15.
The analysis of Stoneley wave propagation in a fracture is essential for the identification and evaluation of fracture parameters from the borehole Stoneley wave. Also, it is important for many geophysics considerations, e.g. for tremor and long-period events observed in volcanoes and geothermal areas. In this paper, we investigate the guided waves propagation in a fluid layer lying between two viscoelastic vertically transversely isotropic media. The viscoelastic mechanism models the attenuation due to the presence of fluid saturation in the rock. A model based on the superposition of three inhomogeneous partial plane waves: one in the fluid and two heterogeneous waves in the solid is developed. The dispersion equation is obtained for this case. A numerical solution is carried out to obtain the guided wave velocity and attenuation coefficient. The results of this investigation show that there is a strong correlation between the velocity dispersion and attenuation of Stoneley wave and the anisotropic parameters of the medium especially in a sandstone (fast) medium. 相似文献
16.
针对饱和多孔介质中热弹性波的传播特性问题,基于多孔介质理论和广义的热弹性模型,研究平面S波在饱和多孔热弹性介质边界上的反射问题。以考虑流-固耦合的饱和多孔介质波动方程和热-弹耦合的广义热弹性基本方程出发,建立饱和多孔介质的热-流-固耦合弹性波动模型。通过引入势函数并考虑自由透水和绝热的边界条件,经过理论推导最终给出在饱和多孔热弹性介质边界上的四种反射波的振幅反射率的理论表达式。在此基础上进行数值计算,分别讨论平面S波的入射频率、入射角和热膨胀系数等参数对四种反射波的振幅反射率的影响情况。结果表明:各反射波的振幅反射率分别随频率和热膨胀系数的增大而增大,同时也受到平面S波入射角变化的影响。该结论对于土动力学的理论研究及其相关的工程勘探具有一定的指导意义。 相似文献
17.
V. Červený 《Studia Geophysica et Geodaetica》2007,51(3):391-410
The reflection/transmission laws (R/T laws) of plane waves at a plane interface between two homogeneous anisotropic viscoelastic
(dissipative) halfspaces are discussed. Algorithms for determining the slowness vectors of reflected/transmitted plane waves
from the known slowness vector of the incident wave are proposed. In viscoelastic media, the slowness vectors of plane waves
are complex-valued, p = P + iA, where P is the propagation vector, and A the attenuation vector. The proposed algorithms may be applied to bulk plane waves (A = 0), homogeneous plane waves (A ≠ 0, P and A parallel), and inhomogeneous plane waves (A ≠ 0, P and A non-parallel). The manner, in which the slowness vector is specified, plays an important role in the algorithms. For unrestricted
anisotropy and viscoelasticity, the algorithms require an algebraic equation of the sixth degree to be solved in each halfspace.
The degree of the algebraic equation decreases to four or two for simpler cases (isotropic media, plane waves in symmetry
planes of anisotropic media). The physical consequences of the proposed algorithms are discussed in detail.
vcerveny@seis.karlov.mff.cuni.cz 相似文献
18.
19.
M. G. Markov 《Izvestiya Physics of the Solid Earth》2009,45(9):769-776
The problem about the refraction of elastic waves at the interface of two half-spaces (rocks) filled with immiscible fluids
is solved with the use of modified boundary conditions of the dynamics of saturated porous media [Nagy and Nayfeh, 1995].
The solution is obtained within the framework of the Frenkel’-Biot theory with allowance for the surface tension at the interface
of fluids for a porous medium formed by two half-spaces, which differ only in the properties of the fluids filling them. Practically
important cases of the reflection from the fluid-gas (water-air) and fluid-fluid (oil-water) interfaces are considered in
detail. The calculations are performed for both harmonic waves and pulses. The possibility to determine in principle the structural
factor characterizing the pore-space geometry of rocks from measured dynamic parameters of reflected waves is shown. 相似文献
20.
During seismic wave propagation on a free surface, a strong material contrast boundary develops in response to interference by P- and S- waves to create a surfacewave phenomenon. To accurately determine the effects of this interface on surface-wave propagation, the boundary conditions must be accurately modeled. In this paper, we present a numerical approach based on the dynamic poroelasticity for a space–time-domain staggeredgrid finite-difference simulation in porous media that contain a free-surface boundary. We propose a generalized stess mirror formulation of the free-surface boundary for solids and fluids in porous media for the grid mesh on which lays the free-surface plane. Its analog is that used for elastic media, which is suitable for precise and stable Rayleigh-type surface-wave modeling. The results of our analysis of first kind of Rayleigh (R1) waves obtained by this model demonstrate that the discretization of the mesh in a similar way to that for elastic media can realize stable numerical solutions with acceptable precision. We present numerical examples demonstrating the efficiency and accuracy of our proposed method. 相似文献