共查询到20条相似文献，搜索用时 15 毫秒
1.
Probabilistic seismic hazard analysis for Bangalore 总被引：5，自引：3，他引：2
This article presents the results of probabilistic seismic hazard analysis (PSHA) for Bangalore, South India. Analyses have
been carried out considering the seismotectonic parameters of the region covering a radius of 350 km keeping Bangalore as
the center. Seismic hazard parameter ‘b’ has been evaluated considering the available earthquake data using (1) Gutenberg–Richter (G–R) relationship and (2) Kijko
and Sellevoll (1989, 1992) method utilizing extreme and complete catalogs. The ‘b’ parameter was estimated to be 0.62 to 0.98 from G–R relation and 0.87 ± 0.03 from Kijko and Sellevoll method. The results
obtained are a little higher than the ‘b’ values published earlier for southern India. Further, probabilistic seismic hazard analysis for Bangalore region has been
carried out considering six seismogenic sources. From the analysis, mean annual rate of exceedance and cumulative probability
hazard curve for peak ground acceleration (PGA) and spectral acceleration (Sa) have been generated. The quantified hazard
values in terms of the rock level peak ground acceleration (PGA) are mapped for 10% probability of exceedance in 50 years
on a grid size of 0.5 km × 0.5 km. In addition, Uniform Hazard Response Spectrum (UHRS) at rock level is also developed for
the 5% damping corresponding to 10% probability of exceedance in 50 years. The peak ground acceleration (PGA) value of 0.121 g
obtained from the present investigation is slightly lower (but comparable) than the PGA values obtained from the deterministic
seismic hazard analysis (DSHA) for the same area. However, the PGA value obtained in the current investigation is higher than
PGA values reported in the global seismic hazard assessment program (GSHAP) maps of Bhatia et al. (1999) for the shield area. 相似文献
2.
《Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards》2013,7(3-4):173-185
The most important seismic hazard parameters required to demarcate seismic zones are the peak horizontal acceleration (PHA) and spectral acceleration (SA). The two approaches for evaluation of seismic hazard are the probabilistic seismic hazard analysis and the deterministic seismic hazard analysis (DSHA). The present study evaluates the seismic hazard of the South Indian Peninsular region based on the DSHA methodology. In order to consider the epistemic uncertainties in a better manner, a logic tree approach was adopted in the evaluation of seismic hazard. Two types of seismic sources and three different attenuation relations were used in the analysis. The spatial variation of PHA (mean and 84th percentile values) and SA values for 1 Hz and 10 Hz at bedrock level (84th percentile values) for the entire study area were evaluated and the results are presented here. The surface level peak ground acceleration (PGA) values will be different from that of the bedrock level values due to the local site conditions. The PGA values at ground surface level were evaluated for four different National Earthquake Hazard Reduction Program site classes by considering the non-linear site response of different soil types. The response spectra for important cities in South India were also prepared using the deterministic approach and the results are presented in this paper. 相似文献
3.
Assessment of seismic hazard and liquefaction potential of Gujarat based on probabilistic approaches
Gujarat is one of the fastest-growing states of India with high industrial activities coming up in major cities of the state. It is indispensable to analyse seismic hazard as the region is considered to be most seismically active in stable continental region of India. The Bhuj earthquake of 2001 has caused extensive damage in terms of causality and economic loss. In the present study, the seismic hazard of Gujarat evaluated using a probabilistic approach with the use of logic tree framework that minimizes the uncertainties in hazard assessment. The peak horizontal acceleration (PHA) and spectral acceleration (Sa) values were evaluated for 10 and 2?% probability of exceedance in 50?years. Two important geotechnical effects of earthquakes, site amplification and liquefaction, are also evaluated, considering site characterization based on site classes. The liquefaction return period for the entire state of Gujarat is evaluated using a performance-based approach. The maps of PHA and PGA values prepared in this study are very useful for seismic hazard mitigation of the region in future. 相似文献
4.
A probabilistic seismic hazard analysis for the states of Tripura and Mizoram in North East India is presented in this paper to evaluate the ground motion at bedrock level. Analyses were performed considering the available earthquake catalogs collected from different sources since 1731–2010 within a distance of 500 km from the political boundaries of the states. Earthquake data were declustered to remove the foreshocks and aftershocks in time and space window and then statistical analysis was carried out for data completeness. Based on seismicity, tectonic features and fault rupture mechanism, this region was divided into six major seismogenic zones and subsequently seismicity parameters (a and b) were calculated using Gutenberg–Richter (G–R) relationship. Faults data were extracted from SEISAT (Seismotectonic atlas of India, Geological Survey of India, New Delhi, 2000) published by Geological Survey of India and also from satellite images. The study area was divided into small grids of size 0.05° × 0.05° (approximately 5 km × 5 km), and the hazard parameters (rock level peak horizontal acceleration and spectral accelerations) were calculated at the center of each of these grid cells considering all the seismic sources within a radius of 500 km. Probabilistic seismic hazard analyses were carried out for Tripura and Mizoram states using the predictive ground motion equations given by Atkinson and Boore (Bull Seismol Soc Am 93:1703–1729, 2003) and Gupta (Soil Dyn Earthq Eng 30:368–377, 2010) for subduction belt. Attenuation relations were validated with the observed PGA values. Results are presented in the form of hazard curve, peak ground acceleration (PGA) and uniform hazard spectra for Agartala and Aizawl city (respective capital cities of Tripura and Mizoram states). Spatial variation of PGA at bedrock level with 2 and 10 % probability of exceedance in 50 years has been presented in the paper. 相似文献
5.
The seismically active Northwest (NW) Himalaya falls within Seismic Zone IV and V of the hazard zonation map of India. The
region has suffered several moderate (~25), large-to-great earthquakes (~4) since Assam earthquake of 1897. In view of the
major advancement made in understanding the seismicity and seismotectonics of this region during the last two decades, an
updated probabilistic seismic hazard map of NW Himalaya and its adjoining areas covering 28–34°N and 74–82°E is prepared.
The northwest Himalaya and its adjoining area is divided into nineteen different seismogenic source zones; and two different
region-specific attenuation relationships have been used for seismic hazard assessment. The peak ground acceleration (PGA)
estimated for 10% probability of exceedance in 50 and 10 years at locations defined in the grid of 0.25 × 0.25°. The computed
seismic hazard map reveals longitudinal variation in hazard level along the NW Himalayan arc. The high hazard potential zones
are centred around Kashmir region (0.70 g/0.35 g), Kangra region (0.50 g/0.020 g), Kaurik-Spitti region (0.45 g/0.20 g), Garhwal
region (0.50 g/0.20 g) and Darchula region (0.50 g/0.20 g) with intervening low hazard area of the order of 0.25 g/0.02 g
for 10% probability in 50 and 10 years in each region respectively. 相似文献
6.
In view of the major advancement made in understanding the seismicity and seismotectonics of the Indian region in recent times, an updated probabilistic seismic hazard map of India covering 6–38°N and 68–98°E is prepared. This paper presents the results of probabilistic seismic hazard analysis of India done using regional seismic source zones and four well recognized attenuation relations considering varied tectonic provinces in the region. The study area was divided into small grids of size 0.1° × 0.1°. Peak Horizontal Acceleration (PHA) and spectral accelerations for periods 0.1 s and 1 s have been estimated and contour maps showing the spatial variation of the same are presented in the paper. The present study shows that the seismic hazard is moderate in peninsular shield, but the hazard in most parts of North and Northeast India is high. 相似文献
7.
Probabilistic seismic hazard of Pakistan, Azad-Jammu and Kashmir 总被引：2，自引：2，他引：0
The seismic hazard study for Pakistan and Azad Jammu and Kashmir has been conducted by using probabilistic approach in terms
of peak ground acceleration (PGA) in m/s2 and also seismic hazard response spectra for different cities. A new version of Ambraseys et al. (Bull Earthq Eng 3:1–53,
2005) ground acceleration model is used, and parameterization is based on most recent updated earthquake catalogs that consisted
of 14,000 events. The threshold magnitude was fixed at M
w 4.8, but seismic zones like northern Pakistan–Tajikistan, Hindukush and northern Afghanistan–Tajikistan border had M
w 5.2. The average normalized ‘a’ and ‘b’ values for all zones are 6.15 and 0.95, respectively. Seismicity of study area was modeled, and ground motion was computed
for eight frequencies (0.025, 0.1, 0.2, 0.5, 1.0, 1.5, 2.0, 2.5 s) for different annual exceedance rates of 0.02, 0.01, 0.005,
0.002 and 0.001 (return periods 50, 100, 200, 500 and 1,000 years) for stiff rocks at the gridding of 0.1° × 0.1°. Seismic
hazard maps based on computed PGA for 0.02, 0.01 and 0.002 annual exceedance are prepared. These maps indicate the earthquake
hazard of Pakistan and surrounding areas in the form of acceleration contour lines, which are in agreement with geological
and seismotectonic characteristics of the study area. The maximum seismic hazard values are found at Muzaffarabad, Gilgit
and Quetta areas. 相似文献
8.
Mumbai city, the economical capital of India, is located on the west coast of stable intra-plate continental region of Peninsular India which has an experience of significant historical earthquakes in the past. The city stood as the fourth most populous city in the world. Recent seismo-tectonic studies of this city highlighted the presence of active West coast fault and Chiplun fault beneath the Deccan basalt. In the present study, spatial variability of probabilistic seismic hazard for Mumbai region (latitudes of 18.85–19.35°N and longitudes of 72.80–73.15°E at a grid spacing of 0.05°) which includes Mumbai city, Suburban, part of Thane district and Navi Mumbai, in terms of ground motion parameters; peak horizontal acceleration and spectral acceleration at 1.0-s period for 2 and 10 % probability of exceedance in 50 years are generated. The epistemic uncertainty in hazard estimation is accounted by employing seven different ground motion prediction equations developed for worldwide shallow crustal intra-plate environments. Further, the seismic hazard results are deaggregated for Mumbai (latitude 18.94°N, longitude 72.84°E) to understand the relative contributions of earthquake sources in terms of magnitude and distance. The generated hazard maps are compared with the zoning specified by Indian seismic code (IS1893: Part 1 in Indian standard criteria for earthquake-resistant design of structures, Part 1—General provisions and buildings. Bureau of Indian Standards, New Delhi, India, 2002) for rocky site. Present results show an underestimation of potential seismic hazard in the entire study region by non-probabilistic zoning prescribed by IS1893: Part 1 with significantly higher seismic hazard values in the southern part of Navi Mumbai. 相似文献
9.
Nadia Tahernia Morteza Khodabin Noorbakhsh Mirzaei 《Arabian Journal of Geosciences》2014,7(8):3259-3269
The development of the new seismic hazard map of metropolitan Tehran is based on probabilistic seismic hazard computation using the non-Poisson recurrence time model. For this model, two maps have been prepared to indicate the earthquake hazard of the region in the form of iso-acceleration contour lines. They display the non-Poisson probabilistic estimates of peak ground accelerations over bedrock for 10 and 63 % probability of exceedance in 50 years. To carry out the non-Poisson seismic hazard analysis, appropriate distributions of interoccurrence times of earthquakes were used for the seismotectonic provinces which the study region is located and then the renewal process was applied. In order to calculate the seismic hazard for different return periods in the probabilistic procedure, the study area encompassed by the 49.5–54.5°E longitudes and 34–37°N latitudes was divided into 0.1° intervals generating 1,350 grid points. PGA values for this region are estimated to be 0.30–0.32 and 0.16–0.17 g for 10 and 63 % probability of exceedance, respectively, in 50 years for bedrock condition. 相似文献
10.
In a previous paper (Makropoulos and Burton, 1985) the seismic hazard in Greece was examined in terms of magnitude recurrence using Gumbel's third asymptotic distribution of extreme values and concepts of the physical process of strain energy release. The present study extends the seismic hazard methods beyond magnitude to the estimation of expectations of levels of peak ground acceleration exceedance thus allowing for a direct comparison between these two methodologies as well as establishing information relevant to design and planning criteria.The limited number of strong motion records do not permit regional study of attenuation of ground vibration in Greece. An average formula is derived from eight well known formulae which resulted from worldwide studies, this is: a = 2164 e0.70m (r+20)−1.80 cm s−2 where a is peak ground acceleration, m is earthquake magnitude and r is hypocentral distance in kilometres. This formula agrees with the observed values of peak ground acceleration values recorded in Greece.Acceleration seismic hazard is calculated at each of six chosen cities. Values of maximum acceleration with probability 70% of not been exceeded in the next 25, 50, 100, and 200 years are obtained along with corresponding values of velocity and displacement. The same detailed acceleration evaluation is then applied to the whole area of Greece by dividing it into cells of 0.5° lat × 0.5° long, and the results are illustrated through isoacceleration maps.Differences in magnitude and acceleration hazard maps reflect the fact that in acceleration hazard assessment the focal distance from a particular place in an important factor. The cities of Heraklion and Rodhos have the lowest acceleration hazard although the expected earthquakes may have large magnitude. Intermediate depth earthquakes characterise these two cities. Acceleration estimates, unlike magnitude hazard parameters, refer to a particular place and not to an area around it. Hence, even if two places have similar earthquake depth distributions, the hazards may differ significantly because of the different spatial distribution of the foci. This is observed in the case of Athens and Corinth. These cities have almost the same magnitude hazard, but the acceleration hazard is much lower for Athens where the hazard is mainly due to more distant earthquakes.The isoacceleration maps for Greece as a whole also define areas of high seismic hazard. These are the areas around Cephalonia and Leukas Islands in the Ionian Sea and the eastern Sporadhes, Lesbos Islands and Chalkidiki in the Northern Aegean Sea. At the 70% probability level the maximum acceleration is expected to be around 0.2g within the next 50 years. The areas where the maximum acceleration at the 70% probability level is expected to reach a value of 0.3g in the next 200 years are around Cephalonia and Leukas Islands and near the Dardanelles. 相似文献
11.
Seismic hazard studies were conducted for Gaziantep city in the South Anatolia of Turkey. For this purpose, a new attenuation
relationship was developed using the data of Zaré and Bard and accelerations were predicted employing this new equation. Deterministic
approach, total probability theorem and GIS methodology were all together utilized for the seismic assessments. Seismic hazard
maps with 0.25° grid intervals considering the site conditions were produced by the GIS technique. The results indicated that
the acceleration values by the GIS hazard modelings were matched with the ones from the deterministic approach, however, they
were underestimated comparing with the total probability theorem. In addition, the GIS based seismic hazard maps showed that
the current seismic map of Turkey fairly yields conservative acceleration values for the Gaziantep region. Therefore, the
constructed GIS hazard models are offered as a base map for a further modification of the current seismic hazard map. 相似文献
12.
The performance-based liquefaction potential analysis was carried out in the present study to estimate the liquefaction return
period for Bangalore, India, through a probabilistic approach. In this approach, the entire range of peak ground acceleration
(PGA) and earthquake magnitudes was used in the evaluation of liquefaction return period. The seismic hazard analysis for
the study area was done using probabilistic approach to evaluate the peak horizontal acceleration at bed rock level. Based
on the results of the multichannel analysis of surface wave, it was found that the study area belonged to site class D. The
PGA values for the study area were evaluated for site class D by considering the local site effects. The soil resistance for
the study area was characterized using the standard penetration test (SPT) values obtained from 450 boreholes. These SPT data
along with the PGA values obtained from the probabilistic seismic hazard analysis were used to evaluate the liquefaction return
period for the study area. The contour plot showing the spatial variation of factor of safety against liquefaction and the
corrected SPT values required for preventing liquefaction for a return period of 475 years at depths of 3 and 6 m are presented
in this paper. The entire process of liquefaction potential evaluation, starting from collection of earthquake data, identifying
the seismic sources, evaluation of seismic hazard and the assessment of liquefaction return period were carried out, and the
entire analysis was done based on the probabilistic approach. 相似文献
13.
香港地区地震风险评价和设防区划 总被引：3，自引：0，他引：3
香港地区隶属于中国板内地震区中的东南沿海块缘地震带。港-九块体为晚中生代至早第三纪以来以持续稳定上升为主的块体, 块体活动性明显地低于其周边相对下沉的中新生代盆地。为此, 赋予港-九块体为最大可信震级M=5.5级潜在震源区, 而其周边中新生代断陷盆地则为最大可信震级M6.0潜在震源。从大陆地震构造成因的环境、潜在震源可信震级范围M=5.0～7.5和近源地震动饱和等三个方面的可比性, 结合中国大陆地震震源破裂尺度和地震烈度影响场, 所建立的反映中国地震构造和震源破裂及地震烈度影响场特点的PGA和反应谱地震动衰减预测关系式可用于香港地区。以50%概率时的中值对中国强震记录的对比, 本研究所提供的经验期望预测关系式, 能包络实际的资料。因此, 用此地震动衰减预测模式对香港地区地震危险性进行评估, 将会得到相对保守地震动预测值。通过香港地区基岩地震动危险性分析和计算, 参照中国大陆地震设防标准, 进行了基岩设计参数确定和区划。以年概率P=0.02、P=0.002、P=0.0004三个概率标准, 对应的地震动重复周期大约分别约为50a, 500a, 2500a的基岩PGA和反应谱, 作为香港地区基岩上构筑物和建筑物可选的基 相似文献
14.
Probabilistic seismic hazard analysis for Kakrapar atomic power station, Gujarat, India 总被引：1，自引：1，他引：0
Seismic ground motion caused by earthquakes mainly affects the constructions and structures around its area of influence. In this context, the probabilistic seismic hazard analysis (PSHA) is a scientific step towards the safety analysis of any major construction such as nuclear power plant. Thus, the present study focused to estimate seismic hazard level at different probabilities for Kakrapar nuclear power plant located in the Western India. The hazard curves for the study area are developed following the procedure of PSHA suggested by Cornell–McGuire. Three source zones, Narmada-Tapti zone (NTZ), Rann of Kuchchh (ROK), and west passive margin (WPM), are classified on the basis of seismicity and tectonic setting of the study area. The estimated maximum magnitude (m max) for NTZ, ROK, and WPM are 6.9 ± 0.57, 6.5 ± 0.64, and 6.1 ± 0.64, respectively. Logic tree approach has been used for the development of hazard curves to account the epistemic uncertainties associated with the analysis. For maximum credible earthquake [MCE, i.e., the probability of exceedance of 2 % in 50 years (return period of ~2,500 years)], the peak spectral acceleration (i.e., PSA at 0.2 s) expected around 5 km of the Kakrapar nuclear power plant (site) is 0.23 g from all source zones; however, at exact site location, it is 0.18 g. The PSA values due to NTZ, ROK, and WPM based on MCE are 0.22, 0.065, and 0.052 g, respectively. In case of design-based earthquake (DBE, i.e., 50 % probability in 50 years (return period of ~110 years)), the calculated maximum spectral acceleration (SA) from all source zones is about 0.045 g. The PSA distribution for the DBE from the NTZ has reached a maximum value of 0.042 g; however, PSA for ROK and WPM is considerably low with a maximum value of 0.022 and 0.021 g, respectively. Considering the MCE and DBE, the estimated PSA at 0.2 s has a highest value of ~0.23 g from all source zones. Spectral accelerations (SAs) correspond to different periods are presented, and SA plots for NTZ zone can be considered as response spectra for the KAPS site. Deaggregation of PSHA in the present study is also discussed. PGA values reported in seismic zonation map and global seismic hazard analysis program around the present study area range from 0.05 to 0.2 g which is slightly lower than the peak acceleration obtained in this study. The results of this study would facilitate in the performance of the site-specific seismic probabilistic safety analysis. 相似文献
15.
Northeast India is one of the most highly seismically active regions in the world with more than seven earthquakes on an average per year of magnitude 5.0 and above. Reliable seismic hazard assessment could provide the necessary design inputs for earthquake resistant design of structures in this region. In this study, deterministic as well as probabilistic methods have been attempted for seismic hazard assessment of Tripura and Mizoram states at bedrock level condition. An updated earthquake catalogue was collected from various national and international seismological agencies for the period from 1731 to 2011. The homogenization, declustering and data completeness analysis of events have been carried out before hazard evaluation. Seismicity parameters have been estimated using G–R relationship for each source zone. Based on the seismicity, tectonic features and fault rupture mechanism, this region was divided into six major subzones. Region specific correlations were used for magnitude conversion for homogenization of earthquake size. Ground motion equations (Atkinson and Boore 2003; Gupta 2010) were validated with the observed PGA (peak ground acceleration) values before use in the hazard evaluation. In this study, the hazard is estimated using linear sources, identified in and around the study area. Results are presented in the form of PGA using both DSHA (deterministic seismic hazard analysis) and PSHA (probabilistic seismic hazard analysis) with 2 and 10% probability of exceedance in 50 years, and spectral acceleration (T = 0. 2 s, 1.0 s) for both the states (2% probability of exceedance in 50 years). The results are important to provide inputs for planning risk reduction strategies, for developing risk acceptance criteria and financial analysis for possible damages in the study area with a comprehensive analysis and higher resolution hazard mapping. 相似文献
16.
High and Aswan Dams Authority (HADA) proposed a plan aiming at constructing a rockfill dam in the Kalabsha area, about 60 km south of Aswan High Dam. The aim of this dam is to restrain the overflow of water to the Kalabsha Valley for keeping one billion cubic meters from being lost due to seepage and evaporation. The safety of dams during earthquakes is extremely important because failure of such a structure may have disastrous consequences on life and property. Therefore, different factors were considered as part of a site assessment. Five seismic source zones, close enough to the site to give rise to potentially damaging earthquake ground motions, were identified. Seven active faults that have the potential for producing significant earthquakes and that pass through or near the dam site were also identified. The earthquake loading represented by ground motions at the site was evaluated. Probabilistic seismic hazard procedures were used for assessing the earthquake loading at six individual sites using Area-and Line-Source Models (ASM & LSM). The ASM is based on current observed seismicity, whereas the LSM is based on geological slip rates. The output represents the expected acceleration amplitude with 90 percent probability of not being exceeded in exposure times of 20, 50, and 100 years. The results from the two models appear to be different, the expected ground motions from ASM were twice as high as expected from LSM. This difference is due to the load of the Aswan reservoir (Nasser Lake) triggering earthquakes on those parts of the faults that lie under the lake at Kalabsha area. The hazard at the selected sites is given by the hazard curve that is represented by the relationship between the peak ground acceleration and its annual exceedance probability. By comparing the curves for the six individual sites for the same source model, it can be concluded that the potential ground acceleration level for all the sites is almost the same. Considering the mean results from the two models, the annual exceedance probability of the expected ground acceleration from ASM is approximately ten times higher than the annual exceedance probability from LSM.Since ASM is based on current seismicity, it is more appropriate forrepresenting the actual hazard for the dam site. 相似文献
17.
Masyhur Irsyam Donny T. Dangkua Hendriyawan Drajat Hoedajanto Bigman M. Hutapea Engkon K. Kertapati Teddy Boen Mark D. Petersen 《Journal of Earth System Science》2008,117(2):865-878
This paper presents the development of spectral hazard maps for Sumatra and Java islands, Indonesia and microzonation study for Jakarta city. The purpose of this study is to propose a revision of the seismic hazard map in Indonesian Seismic Code SNI 03-1726-2002. Some improvements in seismic hazard analysis were implemented in the analysis by considering the recent seismic activities around Java and Sumatra. The seismic hazard analysis was carried out using 3-dimension (3-D) seismic source models (fault source model) using the latest research works regarding the tectonic setting of Sumatra and Java. Two hazard levels were analysed for representing 10% and 2% probability of exceedance (PE) in 50 years ground motions for Sumatra and Java. Peak ground acceleration contour maps for those two hazard levels and two additional macrozonation maps for 10% PE in 50 years were produced during this research. These two additional maps represent short period (0.2 s) and long-period (1.0 s) spectra values at the bedrock. Microzonation study is performed in order to obtain ground motion parameters such as acceleration, amplification factor and response spectra at the surface of Jakarta. The analyses were carried out using nonlinear approach. The results were used to develop contour of acceleration at the surface of Jakarta. Finally, the design response spectra for structural design purposes are proposed in this study. 相似文献
18.
The growth of megacities in seismically active regions around the world often includes the construction of seismically unsafe buildings and infrastructures due to an insufficient knowledge of existing seismic hazard and/or economic constraints. Minimization of the loss of life, property damage, and social and economic disruption due to earthquakes depends on reliable estimates of seismic hazard. We have produced a suite of seismic hazard estimates for Mexico, the Caribbean, and Central and South America. One of the preliminary maps in this suite served as the basis for the Caribbean and Central and South America portion of the Global Seismic Hazard Map (GSHM) published in 1999, which depicted peak ground acceleration (pga) with a 10% chance of exceedance in 50 years for rock sites. Herein we present maps depicting pga and 0.2 and 1.0 s spectral accelerations (SA) with 50%, 10%, and 2% chances of exceedance in 50 years for rock sites. The seismicity catalog used in the generation of these maps adds 3 more years of data to those used to calculate the GSH Map. Different attenuation functions (consistent with those used to calculate the U.S. and Canadian maps) were used as well. These nine maps are designed to assist in global risk mitigation by providing a general seismic hazard framework and serving as a resource for any national or regional agency to help focus further detailed studies required for regional/local needs. The largest seismic hazard values in Mexico, the Caribbean, and Central and South America generally occur in areas that have been, or are likely to be, the sites of the largest plate boundary earthquakes. High hazard values occur in areas where shallow-to-intermediate seismicity occurs frequently. 相似文献
19.
20.
Estimation of seismic spectral acceleration in Peninsular India 总被引：6，自引：0，他引：6
Peninsular India (PI), which lies south of 24°N latitude, has experienced several devastating earthquakes in the past. However,
very few strong motion records are available for developing attenuation relations for ground acceleration, required by engineers
to arrive at rational design response spectra for construction sites and cities in PI. Based on a well-known seismological
model, the present paper statistically simulates ground motion in PI to arrive at an empirical relation for estimating 5%
damped response spectra, as a function of magnitude and source to site distance, covering bedrock and soil conditions. The
standard error in the proposed relationship is reported as a function of the frequency, for further use of the results in
probabilistic seismic hazard analysis. 相似文献